VPN site to Site - contradictory subnet
Hello
I installation of the site to site VPN a lot but never pinned a front overlap problem, I need advice on the configuration / resolution the following:
Site A (our site - ASA 5505 Version 8.4)
Local subnets:
10.10.105.0 24
10.20.105.0 24
Site B (firewall remotely):
10.96.0.0 16
It comes to site B has reported that they have a route to another VPN:
FW-> get route ip 10.20.105.0
Dest for 10.20.105.0
--------------------------------------------------------------------------------------
Trust-vr:-online 10.20.0.0/16 (id = 33) via 0.0.0.0 (vr: untrust-vr)
Interface tunnel.23, metric 1
so this is redundant with our local subnet, they asked if we can NAT 10.20.105.0 24 24 to 10.10.106.0 because they do not have an entry in the routing table for that...
What is the best way to do it? can someone point out how config I can do this please.
Just saw your PM.
You need NAT the subnet on your side then.
network of the LOCAL_NET_REAL object
10.20.105.0 subnet 255.255.255.0
network of the LOCAL_NET_NAT object
10.10.106.0 subnet 255.255.255.0
network of the REMOTE_NET object
10.96.0.0 subnet 255.255.0.0
NAT static LOCAL_NET_REAL LOCAL_NET_NAT destination (indoor, outdoor) static source REMOTE_NET REMOTE_NET
You can use names for the things you love.
Then your crypto ACLs card must make reference to the NAT range IE. 10.10.106.0/24 and not the actual IP addresses.
Jon
Tags: Cisco Security
Similar Questions
-
VPN site-to-site-1 ip private 6 subnets of vlan
My firewall is a Cisco ASA 5520 8.4 (5) running.
I have to install a tunnel vpn site-to-site between a private ip address and 6 private subnets. I work with another engineer on the other side.
private - external ip address static public ip<------site to="" site-----="">outsite static public ip - 6 private VLAN.
Each VLAN must be able to get to the private ip address and vice versa. I'm trying to understand what would be the best configuration.
Any suggestion would be appreciated.
Thank you
Carlos
I think that there is no configuration 'best' just a configuration that should work:
On your ASA set up the VPN with a crypto-ACL as follows:
the object PRIVATE IP network
host 10.10.10.10
network to NETWORK-VPN-REMOTE object-group
object-network 10.100.1.0 255.255.255.0
object-network 10.100.7.0 255.255.255.0
object-network 10.200.1.0 255.255.255.0
...
!
VPN - XXX access list permit ip object object-group PRIVAT-IP NETWORK-VPN-remote CONTROL
!
card crypto VPN 10 corresponds to the VPN - XXX address
On the other side, the crypto ACL must be exactly in the opposite direction. And you have to exempt NAT traffic.
--
------site>
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
VPN site to Site - ASA to PIX - same subnet on the inside
Chaps,
I have a unusual scenario, whereby case I need a tunnel vpn site-to-site between a pix of cisco version 7 and version 8 cisco asa, which have the same subnet ip to each endpoint. Is it possible to create such a tunnel from site to site or do I change one of the remote endpoints?
Thank you
Nick
Hi Nicolas,.
To allow the traffic through the tunnel when having the same at both ends addressing scheme, you should NAT VPN traffic.
That is to say.
Site a 10.1.1.0/24 LAN
Site B LAN 10.1.1.0/24
The site config:
NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0
(in, out) static 192.168.1.0 access-list NAT
license of crypto list to access ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
Site B config:
NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.1.0 255.255.255.0
(in, out) static 192.168.2.0 access-list NAT
license of crypto list to access ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
The idea is that Site A will to 192.168.1.0 translatefd when you go to Site B, and Site B will result to 192.168.2.0 when you go to the Site A.
Hope that makes sense.
Federico.
-
Use the remote website via VPN site-to-site
Hi all
We have two sites, the site has and B. At site A, we have a Web site we want to share with all of site B. Currently, site B can access the site via the VPN site-to site on X 0, which is their LAN. Nothing outside X 0 cannot access or ping to the address.
We added access rules to allow access from the DMZ to this interface, but again, no ping and no communication at all. The other strange thing is that we see that no trip package for these access rules either.
Any help is appreciated. Thank you.
It seems that the demilitarized zone is not part of the VPN tunnel.
Can you confirm that the DMZ subnet is part of local destinations on the site B and a part of the local destinations on site?
Kevin
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
Problem with the VPN site to site for the two cisco asa 5505
Starting with cisco asa. I wanted to do a vpn site-to site of cisco. I need help. I can't ping from site A to site B and vice versa.
Cisco Config asa1
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 172.xxx.xx.4 255.255.240.0
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.60.2 255.255.255.0
!
passive FTP mode
network of the Lan_Outside object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
Access extensive list ip 192.168.60.0 Outside_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_2 of object-group a
network of the Lan_Outside object
NAT (inside, outside) interface dynamic dns
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 172.110.xx.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.60.0 255.255.255.0 inside
http 96.xx.xx.222 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 96.88.75.222
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
inside access managementdhcpd address 192.168.60.50 - 192.168.60.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_96.xx.xx.222 group strategy
attributes of Group Policy GroupPolicy_96.xx.xx.222
VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 96.xx.xx.222 type ipsec-l2l
tunnel-group 96.xx.xx.222 General-attributes
Group - default policy - GroupPolicy_96.xx.xx.222
96.XX.XX.222 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Cisco ASA 2 config
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 96.xx.xx.222 255.255.255.248
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the Lan_Outside object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_4
ip protocol object
icmp protocol object
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_2 of object-group 192.168.1.0 255.255.255.0 192.168.60.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_4 of object-group a
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.60.0_24 NETWORK_OBJ_192.168.60.0_24 non-proxy-arp-search of route static destination
!
network of the Lan_Outside object
dynamic NAT (all, outside) interface
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 96.xx.xx.217 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 172.xxx.xx.4 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 172.110.74.4
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd address 192.168.1.50 - 192.168.1.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_172.xxx.xx.4 group strategy
attributes of Group Policy GroupPolicy_172.xxx.xx.4
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 172.xxx.xx.4 type ipsec-l2l
tunnel-group 172.xxx.xx.4 General-attributes
Group - default policy - GroupPolicy_172.xxx.xx.4
172.xxx.XX.4 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
inspect the httpFor IKEv2 configuration: (example config, you can change to encryption, group,...)
-You must add the declaration of exemption nat (see previous answer).
-set your encryption domain ACLs:
access-list-TRAFFIC IPSEC allowed extended LOCAL REMOTE - LAN LAN ip
-Set the Phase 1:
Crypto ikev2 allow outside
IKEv2 crypto policy 10
3des encryption
the sha md5 integrity
Group 5
FRP sha
second life 86400-Set the Phase 2:
Crypto ipsec ikev2 ipsec IKEV2-PROPOSAL
Esp aes encryption protocol
Esp integrity sha-1 protocol-set the Group of tunnel
tunnel-group REMOTE-PUBLIC-IP type ipsec-l2l
REMOTE-PUBLIC-IP tunnel-group ipsec-attributes
IKEv2 authentication remote pre-shared-key cisco123
IKEv2 authentication local pre-shared-key cisco123-Define the encryption card
address for correspondence CRYPTOMAP 10 - TRAFFIC IPSEC crypto map
card crypto CRYPTOMAP 10 peer set REMOTE-PUBLIC-IP
card crypto CRYPTOMAP 10 set ipsec ikev2-IKEV2-PROPOSAL
CRYPTOMAP interface card crypto outside
crypto isakmp identity addressOn your config, you have all these commands but on your VPN config, you mix ikev1 and ikev2. You have also defined political different ikev2. Just do a bit of cleaning and reached agreement on a 1 strategy for the two site (encryption, hash,...)
Thank you
-
Routing of traffic between two VPN Site-to-Site Tunnels
Hi people,
I am trying to establish routing between two vpn Site-to-Site tunnels which are destined for the same outside the interface of my Cisco ASA.
Please find attached flowchart for the same thing. All used firewalls are Cisco ASA 5520.
Two VPN tunnels between Point A and Point B, Point B and Point C is too much upward. I activated same command to permit security level interface also intra.
How can I activate the LAN subnets traffic behind Point to join LAN subnets behind C Point without having to create a tunnel separated between Point A and Point C
Thank you very much.
Hello
Basically, you will need to NAT0 and VPN rules on each site to allow this traffic.
I think that the configurations should look something like below. Naturally you will already probably a NAT0 configuration and certainly the L2L VPN configuration
Site has
access-list NAT0 note NAT0 rule for SiteA SiteC traffic
access-list allowed NAT0 ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note L2L-VPN-CRYPTO-SITEB access-list interesting traffic for SiteA to SiteC
access-list L2L-VPN-CRYPTO-SITEB permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteA LAN to LAN SiteC traffic must use the VPN L2L existing SiteB
Site B
access list OUTSIDE-NAT0 note NAT0 rule for SiteA SiteC traffic
OUTSIDE-NAT0 allowed 192.168.1.0 ip access list 255.255.255.0 192.168.3.0 255.255.255.0
NAT (outside) 0-list of access OUTSIDE-NAT0
Note L2L-VPN-CRYPTO-SITEA access-list traffic for SiteA to SiteC through a Tunnel between A - B
access-list L2L-VPN-CRYPTO-SITEA ip 192.168.3.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Note L2L-VPN-CRYPTO-SITEC access-list traffic for SiteA to SiteC through a Tunnel between B - C
access-list L2L-VPN-CRYPTO-SITEC permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- OUTSIDE-NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic. It is this time tied to the 'outer' interface, as traffic will be coming in and out through this interface to SiteB
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEA (and SITEC) = are the ACL in the configurations of VPN L2L that defines the SiteA LAN to LAN SiteC traffic should use existing VPN L2L connections.
Site C
access-list NAT0 note NAT0 rule for SiteC SiteA traffic
NAT0 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note list-access-L2L-VPN-CRYPTO-SITEB SiteC to SiteA interesting traffic
L2L-VPN-CRYPTO-SITEB 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteC to SiteA NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteC LAN to LAN SiteA traffic must use the VPN L2L existing SiteB
To my knowledge, the foregoing must manage the selection NAT0 and traffic for VPN L2L connections. Naturally, the Interface/ACL names may be different depending on your current configuration.
Hope this helps
-Jouni
-
Hello please could someone help me regarding my PROBLEM with VPN site-to-site.
I have installation of gateway to gateway unfortunetly I don't have any static IP address, so I have 2 accounts of DynDNS.org on two installation Sites. The two RV042 connect to another router/Modem.
I put the two as router in router Mode and not as a gateway. The VPN status remains tab just to "waiting for connection" I can see the dynamic IP address to connect remotely on the main site and distance from each other. I can ping so two dyndns names. But unable to connect...
The VPN log shows the following.
ERROR: error report asynchronous network on eth1 to message to the port of 105.237.1.xx 500, complainant 192.168.137.153: no route to the host [errno 148, original ICMP type 3 code 1 (unauthenticated)]
What is the main site and 192.168.138.0 the remote site, the main site has a subnet of 192.168.137.0
Please could someone help me or point me in the right direction? Thanks in advance.
Hi Stephen, it may be a few problems. The first is maybe that you said that you have a modem/router device, this means that it is for the RV042 nating. If that's the case then the modems/routers upstream need port forwarding to go to the RV042. ICMP type 3 is a destination unreachable error. That means subnet remote th could not be reached by the applicant rv042. This can withdraw your NAT problem with modems/routers.
So, first thing I would do is port before all the RV042 services to make sure that the firewall on the modems/routers aren't pipe upward works.
-Tom
Please mark replied messages useful -
Static NAT enable VPN site-to-site.
Hello
We plan to build VPN site to site, but, we have a single public routerable internet IP address to assign VPN on Site A, but Site B is ok.
in this case, I think that we must use static NAT on the router, the simple diagram is as below.
internal a subnet - router VPN - router for Internet of the Site - to - VPN - B B Site internal subnet.
the final goal is to make the communication between internal a subnet and subnet B on IPSEC tunnel.
OK, as I said, Site A having a public IP address, then it must use the static NAT and need to apply on the Site router.
Router
interface x/x
Head of ESCR to the internet
NAT outside IP
!
interface x/x
Head of DESC to internal (VPN)
IP nat inside
!
IP nat inside source static (like IP address x.x.x.x) public (as private VPN interface IP x.x.x.x)
so, wouldn't be work without any problem? I think it will work, but I would find other one just in case.
Hey,.
Is that what you try to achieve:
subnet A - A = vpn router = router B - Sub-B network
and you need communicate between Subnet A and subnet via ipsec vpn b?
Concerning
-
Cisco ASA VPN Site to Site WITH NAT inside
Hello!
I have 2 ASA 5505 related to IPSEC Tunnel VPN Site to Site.
A 192.168.1.0/24 'remotely' inside the network and a local "192.168.200.0/24' inside the network (you can see the diagram)
The local host have 192.168.200.254 as default gateway.
I can't add static route to all army and I can't add static route to 192.168.200.254.
NAT the VPN entering as 192.168.200.1 or a 192.168.200.x free to connect my host correcly?
If my host sends packet to exit to the default gateway.
Thank you for your support
Best regards
Marco
The configuration must be applied on the SAA with the 192.168.200.0 subnet it is inside, there must be something like this:
permit 192.168.1.0 ip access list VPN_NAT 255.255.255.0 192.168.200.0 255.255.255.0
NAT (outside) X VPN_NAT outside access list
Global (inside) X Y.Y.Y.Y (where the Y.Y.Y.Y) is the ip address
If you have other traffic on the vpn through the tunnel that requires no nat, then you must add external nat exemption rules since these lines above obliges all traffic through the asa to have a nat statement.
See if it works for you, else post your config nat here.
-
some help me
(Q) ping remote ip unable on ASA is not Firewall not on pc (VPN site to site on SAA) configired no proxy, icmp not inspect, no chance
Note - I can ping PC but not the same subnet ip on ASA2 L3
PC---> > ASA1 - ASA2<>
Hi Matt,
Let me answer your question in two points:
- You cannot ping an ASA on another interface other than the one where you are connected to the ASA of.
For example, ASA1 and ASA2 are connected through their interfaces 'outside '. ASA1 (or any other device on the external interface) can not ping/access ASA2 on his (ASA2) within the interface. The only time wherever this can be substituted is a tunnel VPN with the command "access management" configured for other interface, for example management-access inside
- Traffic ASA1 ping to a remote client behind ASA2 won't over the VPN tunnel and as such is not encrypted. That's because ASA1 will forward traffic based on its routing table that probably this way through its 'outside' interface Except that traffic is allowed with the ASA2 (using the ACL), it will fail.
We can do on the routers of sourcing our ping to another interface, but it will not work on the SAA.
-
cannot ping between remote vpn site?
vpn l2l site A, site B is extension vpn network, connect to the same vpn device 5510 to the central office and work well. I can ping from central office for two remote sites, but I cannot ping between these two vpn sites? Tried to debug icmp, I can see the icmp side did reach central office but then disappeared! do not send B next? Help, please...
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
!
object-group network SITE-a.
object-network 192.168.42.0 255.255.255.0
!
object-group network SITE-B
object-network 192.168.46.0 255.255.255.0
!
extended OUTSIDE allowed a whole icmp access list
HOLT-VPN-ACL extended access-list allow ip object-CBO-NET object group SITE-a.
!
destination SITE-a NAT (outside, outside) static source SITE - a static SITE to SITE-B-B
!
address for correspondence card crypto VPN-card 50 HOLT-VPN-ACL
card crypto VPN-card 50 peers set *. *.56.250
card crypto VPN-card 50 set transform-set AES-256-SHA ikev1
VPN-card interface card crypto outside
!
internal strategy group to DISTANCE-NETEXTENSION
Remote CONTROL-NETEXTENSION group policy attributes
value of DNS server *. *. *. *
VPN-idle-timeout no
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value REMOTE-NET2
value by default-field *.org
allow to NEM
!
remote access of type tunnel-group to DISTANCE-NETEXTENSION
Global DISTANCE-NETEXTENSION-attributes tunnel-group
authentication-server-group (inside) LOCAL
Group Policy - by default-remote CONTROL-NETEXTENSION
IPSec-attributes tunnel-group to DISTANCE-NETEXTENSION
IKEv1 pre-shared-key *.
tunnel-group *. *.56.250 type ipsec-l2l
tunnel-group *. *.56.250 ipsec-attributes
IKEv1 pre-shared-key *.
!!
ASA - 5510 # display route. include the 192.168.42
S 192.168.42.0 255.255.255.0 [1/0] via *. *. 80.1, outside
ASA - 5510 # display route. include the 192.168.46
S 192.168.46.0 255.255.255.0 [1/0] via *. *. 80.1, outside
ASA-5510.!
Username: Laporte-don't Index: 10
Assigned IP: 192.168.46.0 public IP address: *. *.65.201
Protocol: IKEv1 IPsecOverNatT
License: Another VPN
Encryption: 3DES hash: SHA1
TX Bytes: bytes 11667685 Rx: 1604235
Group Policy: Group remote CONTROL-NETEXTENSION Tunnel: remote CONTROL-NETEXTENSION
Opening time: 08:19:12 IS Thursday, February 12, 2015
Duration: 6 h: 53 m: 29 s
Inactivity: 0 h: 00 m: 00s
Result of the NAC: unknown
Map VLANS: VLAN n/a: no
!
ASA - 5510 # display l2l vpn-sessiondbSession type: LAN-to-LAN
Connection: *. *.56.250
Index: 6 IP Addr: *. *.56.250
Protocol: IPsec IKEv1
Encryption: AES256 3DES hash: SHA1
TX Bytes: bytes 2931026707 Rx: 256715895
Connect time: 02:00:41 GMT Thursday, February 12, 2015
Duration: 13: 00: 10:00Hi Rico,
You need dynamic nat (for available IP addresses) for the two side to every subset of remote access to the other side remote subnet and so they can access every other subnet as if both from the traffic from your central location.
example:
Say, this IP (10.10.10.254) is unused IP to the central office, allowed to access remote tunnel 'A' and 'B' of the site.
object-group network SITE-a.
object-network 192.168.42.0 255.255.255.0
!
object-group network SITE-B
object-network 192.168.46.0 255.255.255.0dynamic source destination SITE-a. 10.10.10.254 NAT (outdoors, outdoor)
public static SITE SITE-B-Bdestination NAT (outdoors, outdoor) SITE-B 10.10.10.254 dynamic source
SITE static-SITE aHope this helps
Thank you
Rizwan James
-
Configure VPN site to site with CCP
Hello
I have several VPN site to site of small offices, at Headquarters.
Is possible to make a single configuration for all virtual private networks on the "vpn server"(ISR 1801) or I still need to add an entry for each VPN subnet? ". If Yes, is possible with the CCP?
Kind regards
Nuno
You can then configure the VPN using CCP.
I prefer the command line, and if there are many VPN from Site to Site, you can have a model, and what's happening to one VPN to another is interesting traffic, the INVESTIGATION period by peers and the pre-shared key.
It depends on the policy.
Federico.
-
the traffic in a vpn site-to-site tunnel restrictions
Hello
I have install a VPN site-to site between an ASA 5550 7.2 (3) and the external network of the contractor. I have set up the VPN using the wizard and it worked fine. The wizard has created the cryptomap acl see below
outside_2_cryptomap list extended access allowed object-group ip 10.0.0.0 LOCAL_IPS 255.255.255.0
where LOCAL_IPS is a group of objects containing our local subnets to be dug and 10.0.0.0/24 is the network of the remote end.
I'm trying to restrict the traffic tunnel at about 6 tcp ports, so I changed the acl (using the GUI as well from the CLI) to the following:-
outside_2_cryptomap list extended access permitted tcp object-group LOCAL_IPS 10.0.0.0 255.255.255.0 PERMITTED_TRAFFIC object-group
where PERMITTED_TRAFFIC is a group of TCP services containing the ports we'd like to tunnel.
As soon as I apply this acl (applied at the other end also) the tunnel down and or end it can re - open.
My question is - how do you restrict what traffic (tcp ports) that you want to send in the tunnel on the SAA?
Thank you
Andy
You have 2 options.
VPN-filter
Or something like that...
No sysopt permi-vpn connection
list of access vpn extended permitted tcp object-group LOCAL_IPS 10.0.0.0 255.255.255.0 PERMITTED_TRAFFIC object-group
list of vpn access deny ip 10.0.0.0 LOCAL_IPS object-group 255.255.255.0
extended vpn allowed any one ip access list
group-access vpn in interface inside
-
Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)
Hello
I say hat the chain and responses I've seen to achieve this goal have been great...
https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...
and
https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...
My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"
Thank you
Of course, all this can be configured via ASDM.
Looking at the second example you posted above, they point you first change:
ACL split of the tunnel for the AnyConnect customer
This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.
You then change:
Crypto ACL for the tunnel from Site to Site
To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.
Then, allow the
ASA to redirect back on the same interface traffic it receives
.. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply
Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.
Good luck. Don't forget to note the brand and posts useful when your question is answered.
Maybe you are looking for
-
Satellite A300 - webcam does not work
I'm having the problem with my webcam on Toshiba Satellite A300.I have Windows 7 and just downloaded the latest driver Win 7 for Camera Assistant Software. Software of the camera always not allow me to open camera - keeps saying "Webcam is either dis
-
How to simulate the key 'Enter' in VI?
Hello I would like to do the deed in my vi: 1. open Notepad 2. type '2 '. 3. Type "enter". The problem is that I am not able to simulate the button ENTER. I enclose my vi. Here is the link for my reference above. http://zone.NI.com/DevZone/CDA/EPD/p/
-
problem with timer elapsed sub vi - given RPM
I'm trying to find the rpm of a motor using a proximity detector connected to my cRIO-9012, 9205 module. I am using the timer has elapsed in order to find the time between two pulses of the prox sensor under vi. My problem is it seems to reset when
-
I was using my computer and graphics and words has become fuzzy or blurred, making it difficult to watch and read
-
I am successfully using Microsoft Digital Image Pro 10 with Vista. I used this for many years and do not want to give it up, but maybe need to buy the new computer. Is there a there editing program that compares in quality and ease of use that works