VPN - Tunnel of Split

Similar Questions

• RV016 split support VPN tunnel?

  I read a rumor that the RV016 does not support split VPN tunnels.

  See here:

  http://www.SmallNetBuilder.com/lanwan/lanwan-reviews/31525-Cisco-RV082-and-RV016-v3-VPN-routers-reviewed

  My understanding is that on my router RV042 VPN tunnels will send internet traffic to the local gateway and send the traffic through the VPN tunnel only if they are intended for the remote subnet.  It is my understanding of the "split tunnel".

  Is it not true with the RV016?

  Your understanding on split tunnel is correct. RV016 behaves like RV042 in this regard.

• Tunnel of Split VPN Setup ASA to force inside the tunnel for single address

  Hi all

  We have an ASA with IPSec VPN facility to addresses Internet of Tunnel from Split.  We have an Internet address that must come from the external interface of the ASA.  I have added this address to the list of split tunnel and confirmed on the client that is the road to the tunnel, but I'm not able to get to this address via the VPN.

  How the ASA to allow this unique Internet address to come via the VPN and route back on the same interface to the Internet and the return traffic to back up in the client VPN tunnel.

  I need to get to the address is 213.92.42.118. Here's the config relavent (let me know if I left anything):

  interface GigabitEthernet0/0
  nameif outside
  IP 1.1.1.1 255.255.255.0
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  name 10.80.177.0 VPN_Pool
  Outbound_Ports tcp service object-group
  port-object eq www
  access-list extended sheep allowed any ip VPN_Pool 255.255.255.0
  access-list extended users allow icmp a whole
  access-list extended users enable a tcp
  access-list extended users allow udp a whole
  users_splitTunnelAcl list standard access allowed 10.0.0.0 255.0.0.0
  standard access list users_splitTunnelAcl allow 192.168.43.0 255.255.255.0
  users_splitTunnelAcl list standard access allowed 192.168.40.0 255.255.255.0
  users_splitTunnelAcl list standard access allowed host 213.92.42.118

  FWOB list extended access permit tcp any any Outbound_Ports object-group

  Global (LUXCVGASA01e) 2 1.1.1.1

  NAT (LUXCVGASA01i) 2 10.0.0.0 255.0.0.0
  NAT 0 access-list sheep (LUXCVGASA01i)

  Any help is appreciated.

  -Jeff

  Hi Jeff,

  Just had a chance to look through the Setup and I guess that configured nat is incorrect.

  access-list extended sheep allowed any ip VPN_Pool 255.255.255.0
  NAT 0 access-list sheep (LUXCVGASA01i)
  NAT (LUXCVGASA01i) 2 10.0.0.0 255.0.0.0

  Global (LUXCVGASA01e) 2 1.1.1.1

  The access-list says sheep that ALL traffic goes to the pool of the VPN to go UN-natted. So, when you try to access the public ip address via the tunnel VPN, the traffic the ASA, ASA then performs a search destination NAT and matches the nat command "nat (LUXCVGASA01i) 0 access-list sheep." If the ASA detects a destination NAT translation, it will bypass route search and uses the destination NAT translation to determine the output interface (in this scenario, the output interface is LUXCVGASA01i.

  So, to resolve this problem, change the acl sheep from "any to VPN_Pool 255.255.255.0" inside"to the network VPN_Pool 255.255.255.0.

  clear xlate and re-initialization of the tunnel, and this should solve the problem.

  Let me know if that answers your query.

  Kind regards

  Manisha masseur

• Tunnel of splitting, essentials, and vpn-sessiondb

  Hello

  I'm looking to clarify a few things related to anyconnect vpn.  Here is my setup, I have a portal page custom that users log in which authenticates with RADIUS.  Anyconnect then automatically downloads to the client. Apart from that I use all the features of the portal (clientless SSL was previously used, but not more).  I am preparing a device that will serve as a cold spare and because I no longer need without client I prefer to put everything just licensed Essentials on this, I'll try to find confirmation on a number of things and have not found anything definitive.  Here are the questions:

  1. I can tunnel of splitting with essentials license?  The documentation all said "complete tunnel" is the same as the tunnel of all?

  2. in the execution of a "show vpn-sessiondb svc" the session is shown as a SSL without client, it is ASA 8.2, I lab tested to confirm the default group policy is configured to only allows svc webvpn not as Protocol "vpn-tunnel-Protocol svc", which is the policy applied to the session.  Is this some sort of error 8.2 display?

  3. because I only use the portal for authentication and then page by downloading the client anyconnect this should always work with most of what I read, correct?

  Thanks for taking a peek.

  1. you can probably split tunnel. "full-tunnel" here means "not without customer", everything works exactly as with ordinary vpn cisco client.

  2 al ' 8.4 it shows this:

  Protocol: AnyConnect-Parent-Tunnel SSL

  3. it will work for authentication and the client download, but nothing more.

• No access to Internet with Tunneling active split

  Hi all

  We are facing a problem with tunneling split. Our VPN profile has split the tunnel enabled with only networks allowed to enter the tunnel and the internet traffic is going on locally. Now it works fine almost 90% of users, but some users are unable to access internet when they connected to the VPN. Intranet works very well. Here are some observations from the affected user's machine:

  1. when trying to ping any public FQDN (for example google.com), it is resolved, but when I try to ping with the IP address that it works.

  2. most users access internet VPN has the House, wireless networks usually network 192.168.1.0/24.

  3. this question is only met by some users, other users who also connect to VPN via WiFi at home can successfully both internet & intranet access.

  4 road print machine users watch WiFi router default gateway (192.168.1.1 or private IP). DNS is also the same.

  5A took a capture of packets of users on both adapter AnyConnect & WiFi adapter machine. After analysing captures what we have seen that the public DNS requests are not considered in making that ran on WiFi adapter.

  All guess what might be the problem?

  Any help will be appreciated.

  Thank you.

  Kind regards

  Gerard

  Gaurav,

  Have you tried to disable the IPv6 option under the physical card?

• How to apply internet traffic in VPN tunnel users

  Hello

  Perhaps it is a simple matter to most of you, but it confuses me right now.

  Here's my situation:

  home - internet - ASA 5510 users - CORP LAN

  We have remote Ipsec VPN and anyconnect VPN, I think that the solution must work on two of them.

  My question is: "how to apply internet traffic user home to the VPN tunnel?

  We have "split tunnel" to only"'interesting traffic' VPN tunnel access LAN CORP.

  but now I need apply all traffic (internet + CORP LAN) user through VPN tunnel passes.

  so far, I did what I know:

  1. remove the "split tunnle" group policy

  2. the address in "remote user VPN address pool" are perhaps NAT/PAT travers ASA5510

  but I don't get why it doesn't work.

  all suggestions are appreciate!

  Thank you!

  A few things to configure:

  (1) Split tunnel policy to be passed under split in tunnelall tunnel

  (2) configure NAT on the external interface to PAT to the same global address.

  (3) configure "allowed same-security-traffic intra-interface" so that the tunnel VPN for Internet traffic can make a u-turn.

  Please share the current configuration if the foregoing still does not solve the problem. Thank you.

• VPN Tunnel access to several subnets ASA 5505

  Greetings,

  We spent a little time trying to configure our ASA 5505 in order to TUNNEL into several different subnets.  Subnets include 192.168.1.0 / 192.168.2.0 / 192.168.10.0

  Someone is about to review this setup running and indicate where we have gone wrong.   When I connect via the VPN Client, I can access the 192.168.1.0 network, no problem.  But fail to reach the other two.   Thank you very much.

  Output from the command: 'show running-config '.

  : Saved

  :

  ASA Version 8.2 (5)

  !

  hostname BakerLofts

  activate kn7RHw13Elw2W2eU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  switchport access vlan 12

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.254 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 74.204.54.4 255.255.255.248

  !

  interface Vlan12

  nameif Inside2

  security-level 100

  IP address 192.168.10.254 255.255.255.0

  !

  passive FTP mode

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  vpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

  outside_access_in of access allowed any ip an extended list

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.3.0 255.255.255.0

  Inside2_access_in of access allowed any ip an extended list

  permit Inside2_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 Inside2

  IP local pool vpn 192.168.3.1 - 192.168.3.254 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (outside) 0 192.168.3.0 255.255.255.0 outside

  NAT (Inside2) 0-list of access Inside2_nat0_outbound

  NAT (Inside2) 1 0.0.0.0 0.0.0.0

  Access-group outside_access_in in interface outside

  Access-group Inside2_access_in in the interface Inside2

  Route outside 0.0.0.0 0.0.0.0 74.204.54.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication enable LOCAL console

  AAA authentication LOCAL telnet console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  Crypto ca certificate chain _SmartCallHome_ServerCA

  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130

  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a

  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b

  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504

  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72

  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269

  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d

  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31

  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b

  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20

  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65

  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332

  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329

  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f

  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d

  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597

  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10

  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc

  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b

  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845

  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd

  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced

  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f

  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201

  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868

  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101

  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff

  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777

  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a

  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406

  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973

  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403

  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1

  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b

  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973

  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30

  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603

  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04

  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d

  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101

  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e

  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a

  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018

  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16

  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0

  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8

  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28

  6c2527b9 deb78458 c61f381e a4c4cb66

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal vpn group policy

  attributes of vpn group policy

  value of server DNS 8.8.8.8

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpn_splitTunnelAcl

  username, password samn aXJbUl92B77AGcc. encrypted privilege 0

  samn attributes username

  Strategy-Group-VPN vpn

  username password encrypted QUe2MihLFbj2.Iw0 privilege 0 jmulwa

  username jmulwa attributes

  Strategy-Group-VPN vpn

  jangus Uixpk4uuyEDOu9eu username encrypted password

  username jangus attributes

  Strategy-Group-VPN vpn

  vpn tunnel-group type remote access

  VPN tunnel-group general attributes

  vpn address pool

  Group Policy - by default-vpn

  Tunnel vpn ipsec-attributes group

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  anonymous reporting remote call

  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e

  : end

  I see two problems:

  1. your ASA has not an interior road to the Incas inside networks. You must add:

  Route inside 192.168.2.0 255.255.255.0

  Route inside 192.168.10.0 255.255.255.0

  .. .specifying your gateway address of these networks.

  2. the statement "access-list standard vpn_splitTunnelAcl permit 192.168.1.0 255.255.255.0" sends only a route for 192.168.1.0/24 to your customer. You need to add entries for the other two networks.

• Internet via the VPN tunnel

  Hi I have a question.

  I hope one of you can help me.

  My problem is that I want to the internet using VPN tunnenl.

  I have a VPN connection with my ASA 5505 at home.

  I am able to access the entire inside of the devices. But I'm unable to access the internet.

  is it possible the internet using the internet connection I have at home.

  i'f played a bit with the following commands:

  same-security-traffic permits intera-interface &

   same-security-traffic permit intera-interface & split-tunnel-policy tunnelall

  ASA version: 9.1 2

  ASDM version: 7.1 (3)

  Greetings

  Palermo

  the client that is connected via VPN you are able to ping 4.2.2.2?

  If Yes, if you issue a nslookup google.com is the resolved name?

  If this isn't the case, then I think that the following command highlighted is the problem:

  Group Policy home-attributes VPNSSL
  WINS server no
  DNS server no
  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  Try setting your DNS here server and test.

  --

  Please do not forget to select a correct answer and rate useful posts

• Profile VPN (tunnel group) under the same IP pool

  Hello

  I have on my clients VPN from Cisco ASA 5510 works perfectly. The thing is that now I want to create a new profile or a tunnel in order to create the new cause of ACL I want to restrict only to certain hosts. But I don't know if I can do it under the same IP pool. If the answer is yes how could bind the new tunnel group to the correct ACL.

  This is my config:

  vpnxxxx list of allowed ip extended access all 192.168.125.0 255.255.255.0

  IP local pool ippool 192.168.125.10 - 192.168.125.254

  NAT (outside) 1 192.168.125.0 255.255.255.0

  NAT (inside) 0-list of access vpnxxxx

  RADIUS Protocol RADIUS AAA server

  RADIUS protocol AAA-server partnerauth

  AAA-server partnerauth (inside) host xxxx.xxxx.xxxx.xxxx

  key xxxx

  Crypto-map dynamic dynmap1 20 set transform-set Myset1

  lifespan 20 set security-association crypto dynamic-map dynmap1 seconds 28800

  Crypto-map dynamic dynmap1 20 kilobytes of life together - the association of safety 4608000

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  internal group RA - VPN strategy

  attributes of RA-VPN-group policy

  Server DNS 172.16.1.100 value

  VPN-idle-timeout 30

  Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

  Split-tunnel-policy tunnelspecified

  type tunnel-group RA - VPN remote access

  General-attributes of RA - VPN Tunnel-group

  ippool address pool

  authentication-server-group (outside partnerauth)

  Group Policy - by default-RA-VPN

  tunnel-group RA - VPN ipsec-attributes

  pre-shared-key *.

  Thank you

  The command is "vpn-filter" in the Group Policy section.

  Define a group policy for each group of tunnel and select it with 'by default-group-policy' in the section of the tunnel.

• Tunnel work Split... but only for a single IP address.

  Hi all

  Dealing with a really frustrating problem. Our facility, roughly speaking, is as follows:

  -We have a remote VPN access that users connect to any Connect; in turn, they receive a local LAN address: 10.1.11.192 - 10.1.11.200

  -We have a VPN site-to site that connects to Amazon AWS Access 10.0.249.0 and other subnets and now some hosts on the Amazon * public * network (for example, 54.1.2.3). This is done via a tunnel from split.

  What we see is the following:

  -Users to connect to the VPN and are assigned to one of the addresses above. We use 10.1.11.192 for this example.

  -They can then access anything in the 10.0.249.0 subnet (by the split tunnel) very well. It goes through two ASA devices.

  -They can then access anything in the public network from Amazon (by the split tunnel) very well. This should use Remoting ASA.

  So, it seemed that everything was working. When connected to the VPN, Amazon hosts in 10.x.x.x networks and public IPs I had precisely in tunnel (we plan make the transition to a VPC soon) were accessible, and access came through the VPN IP remote access (IE, when connecting to 54.1.2.3, it showed the user being logged from the address of the gateway from the Cisco IP (, as opposed to the local client IP).

  Now, here's where things are weird: * public * hosts on Amazon in tunnel only works with the first address in the pool, 10.1.11.192. No other addresses don't work. 10.0.249.x is always available, regardless of the assigned IP. 54.x.y.z is only available avec.192.

  I used the same computer with different assigned IPs (10.1.11.193 - 10.1.11.200), and none work. I connected using different computers... they work si.192, but not no matter what other addresses assigned. Other users report the same problem.

  Transfer TCP protocol is a failure

  I'll use our IRC server (and sometimes ssh server) for testing. I can see my laptop the customer with a SYN_SENT on this specific topic. I can see the IRC with a SYN_RECV and shows Server ASA a SYN timeout after 30 seconds. So, it seems that the IRC server packages cannot make their way through the ASA for my laptop the customer.

  I suspect it has something to do with the dynamic static vs NAT, etc, but I've fiddled with every setting I can and come in white.

  I am also puzzled as to pourquoi.192 works, but no other addresses don't.

  I have attached our configuration, less keys and passwords and addresses IP/hostname. It's a little ugly because there some poor attempts to solve this, things will probably remove once it works, but... It might have something to do with randomization of TCP sequence?

  Thanks in advance for any help.

  Hello

  I also enough to explain everything in detail. Even if sometimes it is just too much for my head when I'm tired

  Have you managed to fix the problem that arised to change settings?

  The output of "package Tracker" for the failed connection would be important.

  But now that I look at your original configurations and consider your need for VPN Clients to access a selection of public IP addresses through the ASA it seems to me that perhaps your problem is lack of NAT configuration for this traffic. (which may indicate the "packet-tracer" )

  You need a dynamic PAT from the 'outside' to 'outside' for users VPN be PATed to the external IP address of ASA

  Something like this for example

  network of the VPN-CLIENT-AMAZON-AWS-PAT object

  10.1.12.0 subnet 255.255.255.0

  dynamic NAT interface (outdoors, outdoor)

  Or if your original pool of VPN is used, change the network above.

  Dynamic provisioning PAT above essentially aims to intercept coming from behind 'external' VPN traffic that goes through the 'outside' interface and the dynamic application of PAT for the public IP address of the ASA. For the moment, that seems to me that address network-10 crosses the ASA without NAT essentially leading to SYN timeout newspapers.

  But if I understand you are saying that one of the pool reached VPN address IP address of public destination that does not really correspond with the situation described above. However, I don't see any NAT/PAT configuration for VPN traffic to the public IP address. Look at your log messages. They mention the same IP VPN address pool twice (the other inside the () ) which means there is no NAT for the source address and the ISP traffic naturally declines.

  -Jouni

• How to get specific IP through VPN tunnel

  I've implemented remote access via VPN Cisco VPN.
  We use the tunneling split at the tunel internal IP of VPN tunnel only range.
  Now I need to get a specific IP address on the Cisco VPN Client
  through Internet and internal network.
  I added this specific IP address to split tunnel ACL
  I can check it out using Cisco VPN Client, status > statistics, details of the itinerary.
  but when I traceroute to that specific IP address it ends on
  first jump, ASA public interface.
  ASA road 0.0.0.0/0.
  I need to put in place?

  Hello

  If you need to allow the VPN client to connect to the ASA and you--turn to the Internet, you must:

  permit same-security-traffic intra-interface

  Also, make sure you NAT traffic:

  NAT (outside) 1 VPN-range

  Global 1 interface (outside)

  Be careful with the above NAT commands (is just one example and depends on your configuration).

  Federico.

• Tunnel of splitting with the keyword «exclude...» »

  Client (remote site) = cloud = ASA (HQ) Internet

  Objective, Clinet visit some (blocked on the remote FW) website on the internet through HQ ASA, all other web sites through the

  directly at a distance.

  what I want is to divide the tunnel. and I prefer to use "excluding" an ACL. I have it set to the ASDM. It seems that it does not work. all traffic are always being in the tunnel at the ASA and slitted.

  Also, should I check "Allow Local LAN access" on the Transport tab on the client side?

  newgroup group policy attributes

  value of server DNS X.X.X.X

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy excludespecified

  value of Split-tunnel-network-list ExcludedIP

  Split-dns no

  !!!! some entries in the ACL

  ...

  ExcludedIP standard access list permit 48.14.0.0 255.254.0.0

  Standard access list ExcludedIP allow 48.16.0.0 255.255.0.0

  ....

  When network trace the 48.14.0.0.0 client user, he went to the ASA first...

  Any idea?

  Thank you

  Han

  HI Han,.

  I'm sorry for any delay.

  I duplicated it and that's what you can expect:

  type RA tunnel-group remote access

  tunnel-group RA-global attributes

  address VPN_POOL pool

  Group Policy - by default-RA

  tunnel-group ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  Group RA internal policy

  attributes of RA-group policy

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy excludespecified

  value of Split-tunnel-network-list RA_EXCLUDE

  !

  RA_EXCLUDE list standard access allowed host 4.2.2.2

  RA_EXCLUDE list standard access allowed host 0.0.0.0

  Standard access list RA_EXCLUDE allow 10.198.12.0 255.255.255.0

  Standard access list RA_EXCLUDE allow 10.198.16.0 255.255.255.0

  

  

  Now, I have tested with the latest VPN client available on CCO running on a Windows 7 x 86 computer.

  You don't encounter any problems.

  As agreed before, please test from another machine and let me know.

  Thank you.

  Portu.

  Please note all useful posts

• Configuration of the tunnel of split on an ASA

  Hi Sir,

  I'm setting up a ASA to end remote access VPN. ASA version is 7.2 (1) 24. Client VPN version is 4.6.04.

  I want all the ASA except that user traffic to destination network 10.200.75.0/24-tunnel.

  My config as follows:

  !

  ACL_SPLIT_TUN list standard access deny 10.200.75.0 255.255.255.0

  Standard access list ACL_SPLIT_TUN allow a

  !

  attributes of Group1-group policy

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list ACL_SPLIT_TUN

  !

  The configuration above does not fulfill what I want, during a test in production. Let me know if I have it configured incorrectly.

  Help, please.

  Thank you.

  B.Rgds,

  Lim TS

  Hi Lim,

  It seems that this is not a valid solution... Your question has been to deny traffic on the tunnels of split... The answer

  It's not. None of the clients understand a deny, and therefore refuse is not a valid syntax for the list of split tunnel.

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• SBS 2008 office1 Serv2008 Office 2 need to share assets between them via a site to site VPN tunnel

  Hi all.

  I really need help on this one.

  The office 1 installer running SBS2008 Office 2 running Server 2008.

  Each firm has its own FQDN Office 1 CompanyABC 2 A_B_C of the company office.

  Each firm has its own internal IP address pool Office 1 192.168.69.xxx and office 192.168.20.xxx 2.

  Site to site VPN tunnel between 2 office routers Netgear SRX5308 1 and 2 Netgear FVS318G Office established and working.

  Each firm has its own DNS server and acts as a domain controller

  How to configure the 2 networks to see each other and be able to use assets on every network (files, printers)?

  Is it so simple that the addition of another pool internal IP for each DNS server?

  Thanks in advance for your help.

  Hello

  Your Question is beyond the scope of this community.

  I suggest that repost you your question in the Forums of SBS.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

  "Windows Small Business Server 2011 Essentials online help"

  https://msdn.Microsoft.com/en-us/library/home-client.aspx

  TechNet Server forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• LRT224 impossible to deal simultaneously with more than one VPN tunnel?

  We have configured a client to gateway VPN tunnel group and six in the tunnels of single user gateway on a LRT224. Each unique connection works perfectly using Shrew soft client. But when we try to connect with a second tunnel, the first tunnel disconnects. It seems that the LRT224 cannot process more than one VPN tunnel at the same time? Is there any configuration, that we would have missed?

  TLR log seem to indicate that the Shrew Soft customers use all 192.168.30.0 that their IP address instead of a random IP address in this range.

  Try to set each Shrew Soft client with a specific IP address in the 192.168.30.1 - 50 rank instead of ' use virtual adapter and address randomly.