Vs model model empty

Similar Questions

• I want to print black and white with empty color cartridge. My model is all-in-one HP Deskjet 4288.

  I want to print black and white with empty color cartridge. My model is all-in-one HP Deskjet 4288.

  The Deskjet F4288 joined the printheads on the ink supply.  These are replaced at each change of cartrdige so there is no concern about printing empty color or black cartridges.

  You should be able to print in ink entry mode "backup" by removing color (or black, but not both) cartridges.  There will probably be a warning message about ink backup mode but you should be able to print and the printer will work regardless of the cartridge is available.  In handwritten backup with the only color black cartrdige mode areas will print in shades of gray.  If print ink backup mode only the installed color cartridge then black will be printed by mixing colors.

  See page 75 of the manual here, that says:

  Use the entry ink-backup mode
  Use ink-backup mode to operate the HP all-in-one with only one cartridge. The
  ink-backup mode begins when an ink cartridge is removed from the print cartridge
  transport. During the ink-backup mode, the product can only printing from the computer.
  You cannot start a print job from the control (such as copying or scanning a Panel
  original).

  NOTE: When the HP all-in-one device works in ink-backup mode, a message is
  displayed on the screen. If the message appears and two print cartridges are installed
  in the product, check that the piece of tape plastic protection has been removed
  each print cartridge. When the plastic strip covering the contacts of the print cartridge, the product
  cannot detect the cartridge is installed.

• Table repository - Business model - 10g OBIEE logical to physical table, column mapping is empty

  Hi, I'm really new to OBIEE 10 g.

  I've already implemented a database SQL Server 2005 in physics and import a vw_Dim_retail_branch view.

  The view has 3 columns: branch_id, branch_code, branch_desc.

  Now, I want to set up the business model to map this physical table (view).

  I created a new business model

  Adding new logic table Dim_retail_branch

  In sources, added the vw_Dim_retail_branch as a table source.

  But in the logical table source column mapping tab window, it is empty. I thought he should be able to identify all of the columns in vw_Dim_retail_branch, but no. The spectacle of the mapped column is checked.

  What should I do here? Each column type manually?

  Hello

  You can drag and drop the columns from the physical layer to layer MDB.

  Select 3 columns and drag and drop it to the logical column created in the MDB layer.

  For more reference: http://mkashu.blogspot.com

  Kind regards

  VG

• How to print line empty on the model of BEEP when the field has no value?

  I have a BEEP pattern like below and all these CHILDREN, NAME, GRAND_CHILDREN, are fields arranaged in the model as a line. REPS can enter the values in each of these areas for maximum 3 lines. The first 2 rows have values and the last is empty.
  
  CHILDREN: NAME: GRAND_CHILDREN: NAME:
  Son daughter of John Smith
  Daughter Laura son Kevin
  
  In the third row, because the fields have no value, the report print empty lines, but I want to remove this blank line and display only the rows (first 2 rows) that have values for the fields.
  
  Does anyone know how to get around this problem? Please help me solve this problem.
  
  Thanks in advance,
  RV

  Just having a condition in 3rd row, where DependentDD3 is printed.

  -3rd line 1st column
  last column - 3rd row

  This is true for nullity of DependentDD3. If you want to check for all columns and hide, use condition as

• Data Modeler: the empty namespace at the opening of physical model

  Data Modeler 2.0.0 build 584
  
  I am experiencing strange behavior when opening a physical model recorded previously.
  For some tables, primary keys, and unique keys names are empty.
  Objects that exhibit this problem seem to be random, but which can be otherwise when I hit on a rational model that I have not yet found.
  Also, the generated DDL statements do not contain the name.
  
  Initial situation:
  Data Modeler is not running.
  A data model called MyTestModel including a relational model and a physical model.
  It contains the table named APP_TEST and several other tables.
  
  1. research in the APP_TEST XML to the model of relationship level I see the correct name APP_TEST.
  (The xml file is located in the MyTestModel\rel\ < RelationModelNumber > \table directory)
  If I look at the APP_TEST xml file I see the correct name (APP_TEST) for the table in the physical model.
  (The xml file is located in the MyDataModel\rel\ < RelationModelNumber > \phys\ < PhysicalModelId > \Table directory)
  2. then I launch Data model and open MyDataModel.
  There is no visible physical model for the model of relationship at this point.
  The table at the level of the relationship model shows the name APP_TEST. (Also when you open the properties for the table).
  I open the physical model for Oracle Database11g I saved at the previous session and open the node tables.
  The APP_TEST table has a name, while the other tables have their correct names.
  Do not open the properties for the table APP_TEST the Name property on the general tab is empty, even no space character.
  3. I fill APP_TEST for the Name property, click apply and then OK to exit the properties.
  The physical model is saved and closed. MyTestModel is saved and closed and I out Modeler data.
  4 search for xml files, I see the name APP_TEST is correct for the table at the relational level and the physical model.
  5. I start Data Modeler and reopen MyTestModel. The name of the table is empty again at the level of the physical model.
  
  More observations:
  -When you register a different name (IE APP_TEST_2) from the original at the level of the physical model, the name is preserved when the reopening of the model. Again change its name of origin APP_TEST and name is empty again at the reopening.
  -Fill in name, save, close, and reopen physical model MyTestModel without closing (and savings) shows the same behaviour. If the problem seems really are the physical model.
  -Do not fill in the name (leaving blank) but change a unique key for APP_TEST to the level of the physical model. After you save and close the xml file now also contains an empty name.
  -The same behavior is observed for the primary and unique keys. These keys can belong to a table with an empty name, but also to a table with the name.
  
  Empty names are very problematic because Data Modeler uses the names of the physical model to generate DDL statements.
  Someone at - it problems experienced like that or knows how to get around them?
  
  Thank you
  Enrico

  Hi Enrico,.

  Thanks for the detailed explanation. This behavior is observed when you open the design created with a previous version of the Data Modeler. Physical template names follow the names of relational model if you do not explicitly change them - then name of physical model is used. I hope that the next version will solve your problem.

  knows how to work around the

  the only solution is to change a property in the files, it should be:
                 

  in your case, it is true instead of false.

  Philippe

• Model by default - table cell has no border when the cell is empty: IE6

  Hello
  
  I use the model: dark blue with the model of report of ratings in the region.
  I have a problem in displaying the result in IE6.
  
  When a cell is empty, I have white border in my table instead of edge banding.
  
  Do you know where I can fix this?
  
  Thank you
  
  Roseline

  Roseline,

  You must locate the corresponding css file and look for something like it's - t10 is the number of my theme so replace it with your theme

  Th.t10ReportHeader

  TD.t10data

  TD.t10dataalt

  and add the following code to the css classes:

  empty-cells:show;border-collapse:collapse;
  

  Denes Kubicek
  -------------------------------------------------------------------
  http://deneskubicek.blogspot.com/
  http://www.Opal-consulting.de/training
  http://Apex.Oracle.com/pls/OTN/f?p=31517:1
  -------------------------------------------------------------------

• Win32.Autorun.CFTO [1 - $95CE1D85] (TRegExpr (model): * + operand can be empty (pos 1))

  Using SpyBot... and I get the error message that I can't fix.  Here is the error message I get.

  -List of search results-
  Error in saving! : Win32.Autorun.cfto [1 - $95CE1D85] (TRegExpr (comp): * + operand can be empty (pos 1)) (status)

  How to solve this problem? What this means, is it dangerous?

  Leo, for me that's exactly what happened, Spybot accusing me the same type of malware, avast free antivirus not to blame just about anything!

• Model e9300z #AZ217AV-ABA: help! All files and images are missing. Empty programs

  My PC for 3 1/2 year, has been very slow for a few days. He actually hung online last night and I had to physically stop. I turned everything on time and the screen says welcome to HP as if it were a brand new computer. The homepage is not the usual.  I clicked on the Chrome and the display shows Bienvenuechez Chrome and how to put in place. Ditto for Mozilla Firefox.  Then I go to files and they are empty. Documents and photos. went. Family tree maker is there, but it also gives me the Welcome screen. I went to the original Image and it says that it has been changed in 2013 - day and the year of purchase. It seems empty. It's as if my computer has been deleted.  I backed up a month or two ago and I was actually going to save last night, but when he hung up, I turned it off. I thought that the original Image was a return to the top.  I have Norton AntiVirus.

  What can I do to recover my files? Any suggestions? Can I have a virus? or what happened? Can I fix it myself? A computer store can recover files? I'm typing this on my work laptop. Because I don't know about the use of the computer.

  Thank you all very much.

  Lindsey

  I unplugged the computer because I was worried that if the hard drive was not, that its use could write on previous data. In addition, the power in the House going on and off for a reason any. Since I'm not tech savy, I decided to hire a computer programmer rather than trying to back up my hard drive by using the adapter by myself. When the computer was reconnected overnight by the computer guy, he came as usual. All my files and pictures were back. The screen looked normal.  Yay! The computer guy said my hard drive was fine, but the computer probably had a virus 'Lotus '. I have Norton Anti virus. He ran a few malware research programs and found some viruses. It works fine now. Hope it stays like that. Thanks for the help.

• How to avoid a line empty in the model of .rtf

  Hello
  
  I developed a .rtf report where I have to print the notes of the seller on the table of the line. I want to avoid the empty line if there is no value.
  
  I tried with if condition and decode the State, it did not work. <? xdofx:decode(POL_NOTE_TO_VENDOR,'','',POL_NOTE_TO_VENDOR)? >
  
  Pls advise.
  
  Thank you
  Sridhar

  I guess that the condition is a column. Check if the condition works.
  Remove the space before the end if.
  If this condition does not work, check if the field is referenced correctly.

• I am the only user of this model. Can I remove all or part of the Docs & setting records all users, default user, LocalService, or NetworkService? They are all still empty.

  The only files are in my own project Docs & settings.  Win XP SP3 IE8

  Hello

  If you are the only user who uses the computer the files you are referring are those that would be needed for troubleshooting for any failure of the system. I recommend you do not remove all the files that are hidden or disk rot.

• My library of models is still essentially empty?

  I've updated my yet.  I installed the addition of content.  General menu templates seem to be there... but there is absolutely nothing in the other catalogs... buttons, backgrounds, images, text etc etc.  Nothing there.

  Is there a way to re-initial of the content library?

  Or what could happen here?

  Again help | Download content/functional content free library can help... as I remember, there are TWO files... the program and 'some' of content and a 2nd download for the rest

• "New model of selection" (from sequence) is the empty track creation, with no sequence media

  When I import a sequence After Effects CS6 and then try to create a publication with this sequence, it creates the composition, but there is no track, and there is no media display in the composition in the timeline panel.

  I saw in two different videos, so why isn't my request has the same way?

  After Effects do not use "sequences", that compositions.  That get-sequence converted into a mock-up of the AE import PP.  Simply double click to open it.

• HP HDX 9350EB recognized as HP 8510 X

  Hi all

  I have a weird problem. In my possession is the HP HDX 9350EB, but he thinks it's an HP 8510 X. Even if it is said the system.

  

  This causes of my recovery disks do not work, because the discs are for a HP HDX 9350EB but since it tends to think that it is a HP 8510 X, they are not accepted by the computer.

  I don't have reinstall to factory settings, but it did not help.

  I hope someone can help me and make being recognized as a HP HDX 9350EB again.

  This isn't a software problem, because the factory settings didn't help.

  Model = HP Pavilion HDX 9200 Series

  Message edited by Martin on 26/05/2009 03:19
  Message edited by Martin on 26/05/2009 03:20

  Contact HP or him give to the service. We cannot do anything about it. That's all we can do it by yourself. Here is the link how to get in touch with HP. Choose first your country then you will have this phone in support, links how to find services in your country, e-mail and contact online. Tell them about your problem and that you have updated your Bios to the latest version, but it does not solve it.

  When will contact you keep this open thread or information with you:

  Manufacturer: Hewlett-Packard

  Laptop model: (empty) *

  ID of the system board: 30E2

  Reference number: CH543EA #UUG

  Service ID: 00000

  Processor type: Intel Core (TM) Duo CPU T8300 @ 2.40 Ghz

  Processor speed: 2400 Mhz

  Memory size: 4096MB

  ROM date: 19/06/2008

  The ROM BIOS version: F.39

  Laptop serial number: (empty) *

  Number of portable UUID: (empty) *

  Installed at the factory OS: Vista

  (empty) * no = no value in the BIOS

  This way, you will be able to tell what information is missing in your Bios.

• How to create a pick list in the navigation bar

  Hello

  I use apex5 universal theme and I have an obligation to create a selection list in the navigation bar (before the username and logout) and join a dynamic action. Can someone tell me please how to do this.

  Note: I have created a page zero region. But none of the region of downtown suites this obligation to show the point just before the username and logout.

  Thank you

  Stephanie.

  Guys,

  I thought about a way myself. Its works fine as well. Please find the steps below.

  • Create a region in page zero as a model "empty with attributes.
  • Create a P0_SELECTION to a P0_SELECTION class (if you do not use this class, you can still refer with ID P0_SELECTION, your choice)
  • Create a bar the entrance to the navigation list with the following properties-online class/Image = SELECTIONPOSITION, entry list Label =, Target = URL, target URL = javascript: void (0);

  When you have finished the above activities, go to a page where you would like this item placed in the navigation bar. Simply put the code below in the section JS page (Execute when the Page loads).

  $(". P0_SELECTION')

  .appendTo(".) SELECTIONPOSITION");

  The jquery above to add the item to the navigation class class. Now the best way is to designate the ID. All you need to do is change as below.

  $("#P0_SELECTION")

  .appendTo ("#SELECTIONPOSITION");

  In this way, you can position your elements from anywhere in the page. All you need to do is to create and DISPLAY or class position and adds the element using jQuery.

  Hope this information is useful for someone struggling to position elements in the Web page.

  Thank you

  Stephanie.

• Number of comparison in the sem_match filter clause failed to Jena

  Hello

  I have the following query of sem_match, which has a filter clause to compare a variable with a number. It works in oracle very well; but, he failed in Jena.

  Select interval_length

  table (sem_match ('{? dose_interval RDF: type: Dose_Interval.? dose_interval: dose_interval_hourly? interval_length.}))

  {filter (? interval_length < "6.0" ^ ^ xsd: Decimal)}'.

  sem_models ('test'),

  sem_rulebases ('owl2rl', 'testRules'),

  sem_aliases (sem_alias (", 'http://www.example.com/test#')), null))

  I run the query in Jena, but got the following error:

  Exception in thread "main" java.lang.Error: problems compiling pending:

  The operator * is not defined for the argument type java.lang.String, java.lang.String

  Syntax on the token "6.0" error, * expected

  Is this a bug or something wrong with my request? Thank you very much in advance.

  Hong

  Salvation Hong,

  SEM_MATCH works well on JDBC. (Adapter Jena has performed SEM_MATCH on JDBC for many years.)

  Now, I tried to compile your code and could not be compiled. After correction of some minor problems, I can compile it and run it without encountering errors.

  public class TestHong

  {

  public static String szJdbcURL = "jdbc:oracle:thin:@localhost:1521:orcl";

  public static String szUser = 'scott ';

  public static String szPasswd = "Tiger."

  public static String szModelName = "test";

  public static oracle Oracle new = Oracle (szJdbcURL, szUser, szPasswd);

  Public Shared Sub main (String [] szArgs) throws SQLException {}

  Chart GraphOracleSem = new GraphOracleSem (oracle, szModelName);

  Instruction stmt1d = null;

  try {}

  stmt1d = Oracle.GetConnection () .createStatement ();

  String res = null;

  String szQuery = "select interval_length ' +.

  "table (sem_match ('{?})). dose_interval RDF: type: Dose_Interval. ? dose_interval: dose_interval_hourly? interval_length. " +

  "filter (?). interval_length< \"6.0\"^^xsd:decimal)="" }',="" "="">

  "sem_models ('test'), ' +.

  "null," +

  "sem_aliases (sem_alias (", 'http://www.example.com/test.owl')), "+".

  "null));

  System.out.println ("Request is" + szQuery);

  ResultSet checkInterval = stmt1d.executeQuery (szQuery);

  System.out.println ();

  System.out.println ("* case 1: dose of the medication that is less than the recommended interval range *");

  System.out.println ();

  System.out.printf ("% - 25 s \n", "duration (hours)" ");

  System.out.println ();

  If (! checkInterval.isBeforeFirst ())

  {System.out.println ("OOPS! In case 1, the medication dose intervals were not ");

  System.out.println (); }

  else {}

  While (checkInterval.next ()) {}

  RES = checkInterval.GetString ("interval_length");

  System.out.printf ("" % - 25 s & \n, res);

  }

  }

  System.out.println ();

  }

  Finally {stmt1d.close () ;}

  }

  }

  This is the result I got against a model empty.

  Query is select table interval_length (sem_match ('{? dose_interval RDF: type: Dose_Interval.? dose_interval: dose_interval_hourly? interval_length. filter (? interval_length < "6.0"^^xsd:decimal)="" }',="" sem_models('test'), ="" null,="" sem_aliases(sem_alias('',=""> http://www.example.com/test.owl')}), null))

  * Case 1: meantime of dose of the medication that is less than the recommended interval

  Duration (hours)

  OOPS! In case 1, the medication dose intervals were not

  It will be useful,

  Zhe Wu