Warranty on the brocken screen

Similar Questions

• The gray bar appear on the new screen

  Hi Apple,

  I am facing problem of gray bar on the top of the touchscreen iPhone page. I have been using iPhone for 2012 and very loyal user. For the past two weeks, the touch screen problem is disable and I have to press the top of the screen face hard to exploit the iPhone. My warranty of phone was actually more than 6 months ago. I need another faulty phone. My cousins had the same problem but luckily covered 1 year manufactured warranty. I had already changed my phone twice in the year last because of the same issue. Unfortunately, I have to buy a new device with no choice. If any of you have a good solution please let me know.

  Thank you.

  < published by host >

  Hello

  Your profile says your iPhone is running iOS 7.1.1.

  If that is correct, you can update your iPhone by tapping settings > general > software update (via Wi - Fi) or connect your iPhone to a computer and update via iTunes.

  And try the troubleshooting steps here > If the screen of your iPhone, iPad or iPod touch does not respond to touch - Apple Support

• L2206tm: Image is turning, but the on-screen menu is not.

  My computer woke up this morning to find he had himself handed on and input of the monitor of my Center is "random". However, the menu screen is not. Here's a video. https://goo.GL/photos/1FPTDQ4osarVPVFY8

  Warranty has expired a month ago... numbers.

  Any suggestion would be appreciated. Contact doesn't seem to be affected - touching the top of the screen when the screen is 50% yet "rolled" places the mouse over the available surface.

  I unplugged the monitor for a while. Two months later I tried just for laughs, and it works fine. Very cheap repair bill, I guess.

• Satellite L640 hangs at the splash screen

  Hi all

  I have a L640 / 01 H that I bought earlier this year. In addition to the original Windows 7 OS, I installed a Linux system on a separate partition.

  Earlier today, I was using Linux (which is what I normally use) and everything was really slow.
  Finally I force-shut-down, power button.

  Now, I noticed a problem with the BIOS on this laptop - if I try to start when there is a USB flash drive is connected, the splash screen just hangs. Today when I rebooted I realized that I had left a flash drive, then I got out and I tried to start it again, a couple of times. Whenever the computer crashes just indefinitely on the startup splash screen.

  Finally I gave him enough time and it takes the selection of Linux boot menu, so I tried to start my usual kernel but he gave me some message about a bad MBR.
  I kept trying to start, but the boot process is stuck, what happens is as follows:

  * The three lights on the left (power, battery and light) come on, no problem
  * HARD drive flashes white for a few seconds, then turns off. Occasionally, it will blink again.
  * At the same time, the screen is just stuck on the startup splash screen. If I try to press f2, f12 or any key too many times it will start emitting beeps whenever I press it. There is no way to get into the BIOS settings.

  Also, I can't boot from CD (Windows recovery CD or Linux LiveCD). Finally some kind of time-out of the entry into force, and the computer restarts itself to start the process all. Yay!

  I tried the stuff "unplug the power cord, remove the battery, hold down the power button / stop, plug back in, try to start" but nothing has changed. I also tried switching memory locations (only one chip of RAM, so I can't try a process of elimination on the RAM).
  Finally, I also open the door to HARD disk and removed the HARD drive, then tried to start. This time the BIOS has answered, if only to tell me that there is no appropriate boot media. At this point, the BIOS was responsive and I could change settings in there, but I could not boot from the CD.

  I thought I'd try resetting the CMOS battery, but I'm worried I'll damage something / make the problem worse. Someone at - it ideas? I know that the thing is still under warranty, but service centres are often slow and I don't want to lose the data from the hard drive.

  Any help would be really appreciated.

  > Finally, I also open the door to HARD disk and removed the HARD drive, then tried to start. This time the BIOS has answered, if only to tell me that there is no appropriate boot media. At this point, the BIOS was responsive and I could change settings in there, but I could not boot from the CD.

  It could be a problem with the CD/DVD drive what you think of this idea?
  Perhaps the BIOS does not recognize the CD/DVD drive properly and so there is a problem starting the bootable disc.

  In addition, it might be possible that failures of HARD drive and, therefore, you received an error message about the MBR (master boot record).

  Remove the CD/DVD drive and try to install the Windows booting from a USB flash drive.

  _Regarding the battery CMOS: _
  I would not recommend to disassemble the laptop because you could damage other parts and in addition it should know that the CMOS battery is not removable it s soldered to the motherboard

• Tecra M2: Vertical lines appeared and cannot go beyond the Toshiba screen

  I was watching a movie on DVD WIN and froze my TECRA M2 I restarted, I noticed blue vertical lines on the windows on the screen, then the loading screen went white, I restarted the pc and it Gauthier go beyond screen black screen of toshiba. Some people told me that it is the other HDD VGA. What do you think?

  Hello

  For me, it certainly looks like the graphics card failure!
  It's really bad, because for the most part to the whole motherboard must be replaced! :(
  But to be 100% sure the diagnostic test is necessary.

  I think you should contact the ASP in your country. Guys to explain the situation and ask for clarification.

  Maybe your warranty is valid? In this case all replacements would be FRO free!
  Usually the guarantee must be valid for 24 months if you have saved this notebook on the Toshiba page.

  concerning

• Errors of pixels on the login screen

  For 3 months I have faults of pixels in my login screen. Some black pixels on the screen. But once the connection disappears all the defects of pixels. I have this problem only on the login screen.

  I have this mac for only about 11 months. iMac 27-inch with AMD Radeon R9 M295X 4096 MB. (Retina, 5K). In my opinion, it could be a software problem.

  Someone at - it the same problem? I hope this isn't a hardware problem.

  Thank you.

  You should try to reinstall OS X from your recovery partition. If you have not already, you should consider purchasing Apple Care extended warranty before your one year warranty runs out.

• HP Pavilion Elite HPE-555sc desktop PC - will not get past the first screen of the BIOS

  Hello

  Since yesterday my PC, a HP Pavilion Elite HPE-555sc desktop computer, does not start. It freezes at the start screen "HP".

  It only allows me to enter the BIOS and it meets no other entry.

  I thought it might be the motherboard.

  Is anyone know about this problem? Is it already happened?

  It comes to my PC

  My PC was already supposed to be an upgrade, but I would like to know if this can be corrected before I create a new.

  I knew no more probably is not on warranty.

  Thank you.

  Hello

  Which is usually caused by a corrupt BIOS. You can clear the CMOS. Sometimes, but not always, which solves the problem.

  It is of the card mother reference web page.

  Look for the clear instructions of the CMOS. The instructions do not specify this, but it is best to remove the RTC battery before performing the clear procedure of CMOS.

  While the RTC battery is out and the PC unplugged, press and hold the power switch of the PC for about 15 seconds. When you replace the RTC dough the + must be facing upwards.

  Best regards

  ERICO

• Satellite M60: grey spots on the LCD screen

  It seems that I have a problem with my Satellite M60. I noticed a few more dark spots on the LCD screen. Looks like the screen is dirty (grey size spots about 5-6 pixels), but it seems to be not in the surface of the screen, but on the inside (the surface is perfectly clean) and, certainly, is not the problem of dead pixels or subpixels.

  Is it possible that there is little dust inside of screen? Is it possible to clean it somehow? Such a strange thing is covered by the standard warranty?

  Hi Fox

  Possible it s not a BIOS issue. Of course, I read the other case, but perhaps it s not the same question.

  But do not forget that you are using the good BIOS!
  A lot of users here uses a bad BIOS or bad BIOS procedure.
  In addition, the BIOS version performed from 14/09/06. That is why it s not very old updated.

• HP probook 4520 s held the first screen of the logo

  I was installing windows when the system which took place facing upwards. When I rebooted, it crashes on the first screen of the hp logo. where written "press ESC to display the boot options. without key works ceiling light flashes several times and turn off.
  It is repeated each time. Help, please.

  When it is connected to your desktop computer, can you feel if he goes? When you say that the Bureau does not detect the hard disk, which is in the bios, or when you open my computer?  If the drive is recognized in the bios, you can buy a software like ntfs getback who will try to rebuild the fat table so you can copy items over to the hard drive of the desktop computer.  You can download a trial version that will let you know if it will work, but you will have to buy it to actually transfer the software on disk from the desktop. You can also try to download the certification test of the drive manufacturer that will fix the bad sectors and some minor problems. SpinRite will try to retrieve data for each of the areas that may be of low bits set not completely (upwards or downwards). If the Office does not see the drive in bios, the circuit board on the hard drive is bad or the disc is not rotating. If you gently hold the disc in hand and slightly turn the disc, you should feel a gyroscopic effect of the spinning drive. If you do not feel the disc spins, the motor is probably bad or racing circuit on low hard drive circuit is bad. Sometimes (perhaps 50%), you can try to replace the circuit board with the exact same model Platinum (even if you buy the same model of car, they may have different circuit boards).  The problem is that newer readers have a flash memory chip that stores the settings for each specific access accurate and speed reader. If the exact same Platinum turns the drive, but can't read well, he have to unsolder the flash chip and move it to the new circuit board. Then, the chances improve for recovery. If the new Platinum will not turn the engine, the engine is bad. You will need to send the drive to the manufacturer or to a recovery company that can remove the platters and mount them on their equipment, calibrate and read it (probably $1000 + without warranty). There are people who post how to break on the old engine and replace it with a new one, but I think it would be a mistake to try.

• Lenovo Y510P does not start, the white screen at startup

  Hello world

  I got a Lenovo Y510P with SLI 750 m for about 1 year and 3 months now. 2 weeks (at the time, that I've upgraded to Windows 10). My laptop is suddenly unable to boot most of the time.

  When I press the power, it hangs on the initial empty screen with no logo pop up. I managed to get it started before, simply by restarting again and again, but it's been 3 days and no luck. He simply stays on a blank screen (no), although the keyboard button and the power light.

  Here are the steps I took to solve problems:
  -> Battery removed, disconnected ca, played "suppression of ephemeral power" now the power button for 60 seconds (did it this several times)

  -> RAM removed, changed slots etc. When there is no RAM, the computer continuously restarts
  -> Deleted HARD drive, reinstalled

  -> Removed 2 GPU. When the 2nd GPU is plugged in, the fan will try and turn from time to time

  -> Connectors disconnected to the wi - fi module

  -> Restarted several times

  -> Press the NOVO button, he just brings him to the white screen

  Any advice would be much appreciated. The laptop itself is in good condition and has little physical ware. Unfortunately, is no longer under warranty, and I don't know the cost to send it is quite high.

  
  

• Pile on the Welcome screen

  Nice day

  My HP Probook 430 pile on the Welcome screen, I start HP PC hardware diagnosis for hard drive, I had this IDEA of failure

  Smart Check: spent

  Long DST: failure

  Failure ID: Q0BQ8C-000797-QFPJWK-61AA03

  Product ID: F3k78PA #UUF

  can someone help me with this error?

  Hello

  Error code 24 characters long drive Self Test (DST) would indicate that hard is defective and must be replaced.

  If your laptop is still under warranty, contact HP Business Support and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• I have a HP Photosmart C8180 printer on the printer screen it displays C2FF8575.

  I have a HP Photosmart C8180 printer.  On the printer screen, it displays C2FF8575.  It won't turn off, unless I unplug islet that my Undo button keeps flashing. What does all this mean?

  The code of C2FF8575 refers to a fatal mistake in the firmware of the printer. The only thing you can do when this error is a hard reset. I will include the instructions below. If this does not work, you will need to replace the printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form:
  http://goo.GL/w7Hgh

  To do a hard reset:
  1. make sure that the printer is turned on.
  2. pull on the power cord from the printer.
  3. pull out the power cord from the wall.
  4. wait for 30 seconds.
  5. plug in the printer and turn it on.

• 2014 Pavilion pass the recovery screen

  I have a HP Pavilion model 17-e019dx running Windows 8. Whenever I turn it on, it stops with a blue screen that says:

  Recovery

  Your PC needs to be repaired

  A required device is not connected or is not accessible

  0xc000000f error code

  When I press on enter to 'Try again' it back with:

  File:\Windows\System32\winload.efi above the above error code.

  I tried the recovery and after a LOT of waiting time, it always comes back to the above screen. I also ran all the diagnostics that are available on the laptop and all come back normal. I don't have the disks or the original documents that I "received this laptop as a 'gift/curse' of another frustrated individual who he bought earlier this year. It seems to be under warranty through 12/14, but I have no purchase receipts, so I don't think I can take it anywhere. It is, however, saved for me.

  Help, please!

  You can order your support page recovery media. Scroll through the list of software drivers to see the possibility of ordering:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4132&LC=en&cc=us&DLC=en&sw_lang=&product=6627485

  BTW-check status guaranteed here:

  http://h10025.www1.HP.com/ewfrf/wc/weInput?cc=us&LC=en & LC = in

• HP 15 Notebook PC L3Q92EA #ABU: HP Pavilion, 8.1 Win "Please wait" when the unlock screen saver

  Just bought an HP 15 Win8.1 running laptop.  I think it's a huge pain to use.  Once the screen lock is committed, it takes forever to get the login screen to appear.

  I move the mouse or press a key to get the screen to go back, but I see is the screen "Please wait" for more than a minute then a background appears.  Click the mouse and I have one more minute of "Please wait" before the logon screen appears.

  Can anyone help, until the laptop goes through the window?

  Hello

  Thanks for posting your concern on the Forums for Support and sorry about the problem you are having. I went through your post and it sounds like I should be able to help with the problem.

  I suggest you perform the test (Test of the HARD disk) on the computer. Follow the steps below-

  • Switch off the appliance.
  • To turn back press the power button and as soon as you release, keep pressing the "ESC" key, unless a screen comes up, you might want to wait a minute while tapping the button.
  • In the start menu, choose F2 - System Diagnostics.
  • HDD test would be under the Test component. (usually, it is recommended to test rapid and wide, but for now because the PC is new I rather suggest you simply run the Quick Test).
  • After you choose the Quick Test, click on run once.

  If he succeeds, you can proceed with the recovery, part if she fails to give a call to tech support at the number mentioned below, since the unit is under warranty, you should be able to get help to get the drive replaced.

  On the recovery procedure, its complete restoration of unit settings factory which means that the data on the computer is cleared and with it, the software that can be installed on it. Please follow the steps below to perform recovery-

  • Switch off the appliance.
  • To turn back press the power button and as soon as you release, keep pressing the "ESC" key, unless a screen comes up, you might want to wait a minute while tapping the button.
  • In the start menu, choose F11 - system recovery.
  • On the next page of options, you can choose - "troubleshooting." (If it is a unit of windows 8, or you can skip this step)
  • On the next page, you will need to choose "Recovery Manager". (If it is a unit of windows 8, or you can skip this step)
  • On the next page in the first column, under "I need help immediately", you must choose "Reduced Image Recovery"
    • Now, here, you can get an option to backup your files, because it would be an option to say - recover after saving files or recover without backup of data.
    • You will need to insert the disc followed the screen - instructions here on and unit should be returned to its original state.

  Now if you need help email us back or call HP SUPPORT @ 1-800-474-6836 [24/7 SUPPORT].

  Although I work for HP, but I am personally.

  Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution. Click on the 'Bravo Thumbs Up' on the left to say 'Thank you' for helping!

  Concerning

  Aks3621

• How to activate the touch screen HP Pavilion Touch Smart (10-e010nr)

  The list of features on the HP website says that this laptop has a touchscreen, but the first time that I booted up (new with box), it doesn't seem to work.  I have run Windows Update and installed all security and optional updates.  I also installed all video updates from the HP support page.  What can I do else?  It has touch screen or not?  It had pre-installed Windows 8.1.  Thank you!

  Last night I did the reset complete back to factory settings... erase all files and reinstall Windows 8.1.  It took several hours.  It did not touch screen feature.  I also tried pressing F2 at startup and running the diagnostics on all of the touch screen.  He failed and gave me an error code.  As the computer is still under warranty (I don't have possession for another week yet), I talked to HP technical support on live chat and gave him the error code.  He said he must be sent to HP for service.  Since I live on a military base that, he told me that I must call their number of military sales to the United States.  When I called them, they were closed.  I won't and I'll try to return it to the base exchange where I bought it.  Thanks for trying to help me solve this problem.  I guess that's just DOA.

  Andrew