We have a new RDS terminal server

Similar Questions

• 2611XM Terminal Server + ACS + new authentication when selecting menu options

  Hello

  I managed to configure ACS authentication on my 2611xm router,

  After you connect to the router, I have an autocommand configuration to run a menu.

  My problem is when you select the option in the menu,

  You are then re invited to reauthenicated against the router before connecting to the line,

  can someone tell me how to prevent it.

  Thank you for your time and effort in advance, I have attached a config below.

  DDRAS01 #sh running-config

  Building configuration...

  Current configuration: 6854 bytes

  !

  ! Last modification of the configuration at 10:28:49 GMT Sunday, February 21, 2010 by

  !  NVRAM config update at 19:25:53 GMT Saturday, February 20, 2010 by

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  Service linenumber

  sequence numbers service

  !

  hostname DDRAS01

  !

  boot-start-marker

  boot-end-marker

  !

  Security of authentication failure rate 3 log

  Passwords security min-length 6

  logging buffered 51200 informational

  record of the rate-limit all 10000

  recording console critical

  enable password 7

  !

  AAA new-model

  !

  !

  AAA authentication login default group Ganymede + local

  AAA authentication login if_needed local

  the AAA authentication enable default

  AAA of authentication ppp default local

  AAA authorization exec default group Ganymede + local authenticated by FIS

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  !

  AAA - the id of the joint session

  clock timezone WAS 10

  summer time clock WAS recurring last Sun Oct 02:00 last Sun Mar 03:00

  no location network-clock-participate 1

  No network-clock-participate wic 0

  IP cef

  !

  !

  !

  !

  list of IP domains

  list of IP domains

  IP domain name

  the IP 2033 172.16.1.1 host dd-cr-01F

  ddsws01 host IP 172.16.1.1 2034

  ddsws04 host IP 172.16.1.1 2035

  ddce565 host IP 172.16.1.1 2040

  IP-name server

  IP-name server

  !

  !

  !

  password username d ' operators 15 7 privilege

  !

  !

  property intellectual ssh source interface FastEthernet0/0

  property intellectual ssh event logging

  property intellectual ssh version 2

  !

  !

  interface Loopback0

  IP 172.16.1.1 255.255.255.255

  !

  interface FastEthernet0/0

  IP 255.255.255.0

  Speed 100

  full-duplex

  !

  interface Serial0/0

  no ip address

  Shutdown

  !

  interface BRI0/0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet0/1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0

  !

  IP http server

  no ip http secure server

  Ganymede IP source interface FastEthernet0/0

  !

  radius of the IP source interface FastEthernet0/0

  exploitation forest installation local6

  logging

  SNMP-server RO community

  SNMP-server RW community

  SNMP server location

  contact Server SNMP d ' operators

  !

  title of menu ddras01 ^ C

  Server Terminal Server for Cisco

  Select number from the list below

  Use "ctrl + shift + 6" then 'x' to switch to the menu

  ^ C

  text of ddras01 to menu 1 connect to the DD-CR-01

  order of menu 1 ddras01 resume JJ-cr-01 / dd-cr-01 2033 telnet connection

  ddras01 text menu 2 connect to DDSWS01

  order of menu 2 ddras01 resume ddsws01 / ddsws01 2034 telnet connection

  text menu 3 ddras01 connect to DDSWS04

  order of menu 3 ddras01 resume ddsws04 / ddsws04 2035 telnet connection

  text menu 8 ddras01 connect to DDCE565

  order of menu 8 ddras01 resume ddce565 / ddce565 2040 telnet connection

  menu 9 ddras01 text output

  menu ddras01 command menu-exit 9

  ddras01 menu clear-screen

  menu ddras01-status line

  menu-ddras01 line mode

  radius-server host 10.2.0.50

  RADIUS-server application made

  radius-server key 7

  !

  control plan

  !

  privilege exec 15 level write terminal

  writing level 15 privileges exec

  Ping privileges exec level 1

  privilege exec 10 undebug ip icmp level

  privilege exec 10 undebug ip level

  level of privilege exec 10 undebug all

  privilege exec 10 undebug level

  terminal monitor exec level 10 privileges

  privilege exec 10 level terminals

  privilege exec 15 level show running-config

  See configuration at the privileged exec level 5

  show privileges exec level 5

  privilege exec 10 debug ip icmp level

  privilege exec level 10 debug ip

  privilege exec 10 level debug all

  debugging privileges exec level 10

  clear interface of privileges exec level 10

  clear counters at level 10 privilege exec

  level of privilege exec 10 clear

  !

  Line con 0

  password 7

  Synchronous recording

  line 33 64

  No exec-banner

  exec-timeout 0 0

  no activation-character

  No exec

  preferred transport telnet

  transport of entry all

  character of exhaust-27

  StopBits 1

  FlowControl hardware

  line to 0

  line vty 0 4

  password 7

  Synchronous recording

  ddras01 menu autocommand

  line vty 5 181

  password 7

  Synchronous recording

  ddras01 menu autocommand

  !

  NTP-period clock 17208487

  source NTP FastEthernet0/0

  NTP server

  end

  Hello

  You have aaa login default configured for authentication, with this you get invited

  When you try to access the line.

  Under line VTY 5 181 try adding:

  authentication of the connection /NOAUTH

  exec authorization /NOAUTH

  Add the lines of aaa:

  /NOAUTH AAA authentication login no

  /NOAUTH AAA authorization exec no

  This should stop the authentication to the lines.

  -Jesse

• I have a windows 2008 Server, it works fine and original OS. now, I want to use TERMINAL SERVER.

  I have a windows 2008 Server, it works fine and original OS. now I want to use TERMINAL SERVER please tell me for terminal server I have to buy
  any server terminal server license or not.

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• I have a new server and you cannot use Remote Desktop connection.

  I HAVE A NEW SERVER (HP ML110 G6) AND HAVE USED OLD HARD DISKS, BUT MY REMOTE DESKTOP CONNECTION WILL NOT ME OR OTHERS - WHAT COULD THE REASON BE?

  Hello

  I suggest you to try the steps below and check if it helps.

   The problem can also be caused by your security such as anti-virus program or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.
  Disable the antivirus software:

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  May also need to do this on other computers as well.

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Hope this information is useful.

• Terminal Server license EXPIRING under Advanced Server 2000 Services

  We will be upgrading to a new server (using windows Server2008) S/W & hardware with a new provider in the next 6 months. However, we need to use Terminal Server services for the next 6 months on our current Server 2000 advance server until we have transitional...

  We just started having this message when logging in remotely: "your Server Terminal services temporary client license will expire in 13 days. Please contact your system administrator to get a permanent license. »

  Although advanced server 2000 is not supported, we need to access the remote server for about 6 months until we do the transition...  We are a very small medical office and if we cannot access the server remotely, we are in big trouble! Our doctor S/W is old and is no longer sold or taken in charge by the seller.  We were told that it would not go on the latest server software that is available.

  Is it possible to temporarily reactivate (period 6 months) the license for Terminal Server services?  I thought we had a permanent license and have never seen this message before. My guess it is initially set to expire at that time.

  Is there something we can do?  Registry editing? Y at - it another software that we could use instead of the Terminal services Server to temporarily access the Advanced server 2000 remotely, once the Terminal Server services license expires? Can we buy a license 'enewal"for a period of 6 months/1 year until we have to transition?

  I hope someone can help us, any help is greatly appreciated!

  Hello

  You can ask your question on Windows Server here on the TechNet forums. They are a team who assists the server problems.

  https://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer

  Hope the helps of information.

• Terminal Server RDP is very slow!

  Hello!

  I have a small network with a domain controller Active Directory (Windows 2003) - including the Exchange, I had a Windows 2003 Terminal Server initially, but have replaced the Windows 2003 Terminal Server with a Terminal Windows 2008 Enterprise Server (not R2). Windows 2008 is a completely new system, not an upgrade.

  The problem is that the new Terminal Server ('08) is running very very slow one time the old 2003 Terminal Server is not present on the network. Although I use is no longer the old server, he seems to have an impact on the performance of the network.

  For example, if I should shut down the old server, the new server becomes very slow. It takes about 5 + minutes to services/applications load after you try to connect to the server using RDP. You get a white screen for a long time before the icons are loaded and everything works really slow, including Outlook. On the contrary, once the old server is started in Windows, the new server works very well.

  All servers are physical boxes and I'm not going to finally get rid of the old Terminal Windows 2003 server.

  When you configure the 2008 Terminal Server, I did transfer the IP address of the Terminal Server, the Terminal Server 2008 Server, 2003 server and give the old server a new IP address. I don't know if it has something to do with the behavior, but the old server is not used. It is initialized only to try to keep the stable network.

  Jale01

  Ask in the forum Windows Server:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Errors in user profile on the server terminal server 2008 R2

  I have a problem on a Windows Server 2008 R2 SP1 running Terminal Server services with roaming profiles. The server works as a terminal server server for some time without any problems, but a few weeks ago he began logging on users with temporary profiles or refusal to sign indicating "the user profile Service has no logon. User profile cannot be loaded. "Once rebooted the server seems to act normally, but when 8-10 users have experienced successful logons, the above behavior reappears. At the end of the day, when the activity of the user falls, he can still connect new users - it seems that it is not related to the content of the files of the user's profile. When I check the event logs, the user profile service seems to work, successfully copying profiles on local profile paths. The Windows Modules Installer service cannot be started, error 1450 insufficient system resources. SFC and Windows Update don't work either, probably related to the error of the Windows Modules Installer. In addition, a mistake DCOM ("the server is not registered... ") is recorded in the log of events after each reboot, by referring to the"component base maintenance Session. My impression is that this problem is related to a kind of inadequate resources (non-material resources, the server is well equipped for the current level of activity), so I was running after the registry size, memory management, memory paged and nonpaged pool size, etc, but without any significant success. I realize that it is a somewhat soft and open query and I'll be happy to provide all necessary information - I spent a bit of time on this problem, and any suggestion or comment is welcome.

  This kind of question is really beyond volunteers in this forum, which
  deal with Windows users with security issues.  You must go to
  TechNet and browse the forums to see if there is a good place for this post,.
  TechNet is where the gurus of Pro and server IT hang out.

• Error in Windows Server 2008 R2 Terminal Server printing

  Hello

  Recently, we encounter an error when printing with our new printer to Terminal Server (Windows Server 2008 R2 Standard 64-bit Edition). Once we remotely to the Terminal Server, we are able to see the printer redirect, but when we test print he meets an error and cannot print. Please help and advice. Your quick response with goodness and advice will be highly appreciated. Thank you.

  Hello Djemila,

  Microsoft Communities is for consumer issues in Windows 8, Windows 7, Windows Vista and Windows XP. Your question is dealing with Terminal Server in Windows Server 2008 R2 server and would be better treated in the TechNet forums.
  Click here for the repost in Windows Server 2008 Terminal Server forums.

  They have experts for help with your issue.

  Sincerely,

  Marilyn

• Server Terminal Server 2000 running, Memory Dump, restarting and checking bug error 0x0000007f

  I've been to dump memory and blue screen on a Windows Server 2000 Terminal Server running.

  I had to change the server for a complete memory dump to just check bug 64 MB because memory dumps were fill the C drive and it is the same mistake each time it fails.

  It is a production server and is vital to my business.

  I don't want to just install the 5 or 6 different patches from Microsoft that references the same exact error code, error message stop and symptoms for Server 2000.

  I just replace the memory new inside with two sticks and I even changed the boxes it was with one that has no hardware problem as I have a few of them.

  So he this 2000 Server had the motherboard, processor, memory, network, Audio card, changed video cards and I always get this accident a few times a day.

  I can't find anything definitive on this so if anyone has had the same problems and found a solution, then I'd be very happy to help.

  I am doing a complete network upgrade in the next month or two.

  My work is located in the middle of the busy season and I cannot take the server down and impossible to install anything that could cause a hard accident and not to start again.

  I'm in the middle of an upgrade of the network and we'll go virtual with this server with as many others as I can.

  I need to this Terminal Server to stop crashing and to find a solution for it, while the summer crowd is full swing at my work and it will improve after this summer.

  Any help would be awesome.

  Thank you and sorry for the long post.

  Here's the info I get from BlueScreenViewer when you look at the minidump

  Bug UNEXPECTED_KERNEL_MODE_TRAP control chain

  Bug check code: 0x0000007f

  Parameter 1: 0x00000008

  Caused by the driver ntoskrnl.exe

  Plant address: ntoskrnl.exe + 66e09

  32 bit processor

  This forum is for the support of end users, the users of the computer at home, have problems with Windows.  People server all hang out them in the TechNet forums then you might want to try this post it there instead.

• I managed to install user Terminal Server 2003 10 CLIENT access on a Small Business Server Premium 2003R2 licenses but I've always allowed 2 simultaneous connections.

  The Terminal server server is located on the the same computer as the SBServer also I have validated licenses with Microsoft as well as installation.

  Hello

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• HP Color LaserJet Pro M176n can take care of Terminal Server print?

  Hi all

  Because my HP P1102 printer cannot print RDP, so I decided to buy a new printer for the printing of the server terminal server. I am currently using Windows 7 64 bit and the terminal server of my company is can I 2008 Server 64 bit.

  Someone know if HP Color LaserJet Pro M176n support RDP printing needs? If not, please would you advise another model of the printer for the printing of the server terminal server thank you.

  Kind regards

  Lapson

  Don't worry about the model of the printer when you print from.  Is the printer driver which needs to understand where the print job is coming so that he can pass the print stream to the printer.  If the printer driver is not allowed to communicate between the server and your computer, then you must correct this problem first.

  Printing from a Server Terminal Server is normally something that needs to be configured when printing to a USB cable.  Your RDP client has its enabled print transfer function which allows him to pass the objects on your printer to your personal computer on the server.  Without the correct feature is enabled, you will not be able to print with any printer USB model.  Check with your system administrators to see if they can enable redirection of printer for you.

  Otherwise, you will need to find a way to install your printer on the network.  This can be difficult if you are telecommuting from a personal network printer does not exist on the corporate network.  It's less that you can get your company to install a router with a VPN feature on it.  In this way, you can connect multiple personal devices on the corporate network.  However, your network admins should be aware that you eat additional IP addresses on their network and that he can't ask you to do it at all.

  Otherwise print on a network currently on the network printer should be child's play.  All what you need to do is install a UPD on the server and that it points to the IP address of your network printer desired.  The server will have no problems to send jobs to the printer from here.

• Problem with Photoshop crashes or freeze for users on a server terminal server

  Dear Forum!

  I'm having trouble with Photoshop gel over a period of 20 minutes when you (1) user gum with special brushes and (2) copy and paste the material to a PDF file in Photoshop. As you can see by the size of this post, I'm getting quite depserate here and need help.

  Some background information...

  Photoshop CS6 is installed on a server terminal server with approximately 25 active users where 3 of them are using Photoshop.

  The operating system on the server is Windows Server R2 2012.

  There are no extra modules just a simple installation of Photoshop in this case.

  The server uses 40-60% of the memory most of the time (for the most part, a little less, sometimes a little more, but never 100%) and 40% of the CPU.

  There is enough free space on the disk.

  The problem in detail...

  There are two occasions where the gel was held most of the time. After that it crashes for the first time, it will happen whenever you do any operations over a period of about 20 minutes and it is reciprocal for all users. When it freezes, freezes any terminal session but the program, I always answer (it is not in of "not responding") when you look at another user via the Task Manager. Ending the process as an administrator works sometimes, although the moment where I end it process it takes about 10 to 60 seconds before the program closes actually and the user gets back control. The best thing to do most of the time, if an administrator requires them to close the session.

  
  

  1. the first opportunity is when you use the eraser with a brush that is not a standard but added manually. The names of the brush packages used are:
  Extacy__Elemental

  KKC_Fractal

  Kornkid's_Grunge_Set

  and the problem is with all the brushes inside those packages. How I evoke the problem is the following:

  1. start Photoshop

  2. create new

  3. fill the background with any color

  4. Select the Eraser tool

  5. change the brush to one of those mentioned above

  6. program freezes

  2. the second scenario when the problem occurs is when users copy something from a PDF in Photoshop. The way I talk about it is:

  1. open a PDF file

  2. Select the box and copy it

  3. open Photoshop

  4 create new

  5 paste in Photoshop

  6. program freezes

  So far, we've tried solutions...

  I worked on it for several tour now and I'm not entirely sure on what exactly I did. I'll try and do the following once more, but I'm sure I've tried most of them.

  
  

  Update graphics card drivers.

  Reset all tools:

  1. Select a tool options

  2. choose «Reset all tools»

  Reset default settings:

  1. hold ctrl + shift + alt for Photoshop to start

  2. Select "Yes".

  Tested if it matter if I have a pen or not connected, which it doesn't.

  Removed Special brushes (but it's still freezing when copy/paste of the PDF)

  Deleted 'save in the background' and 'automatically save recovery information' options

  Update to the latest version.

  Off to OpenGL

  Solutions I have not, but I'll try...

  Reinstall Photoshop

  Change the font preview size

  1. go to "type".

  2. Select "prview font size."

  3. Select 'none '.

  Delete the cache of system fonts

  1. Close all Adobe applications, including the application of office (if installed) creative cloud.
  2. Go to \Windows\ServiceProfiles\LocalService\Appdata\Local
  3. Remove the * FNTCACHE. * DAT or * FontCache*.dat files.
     NOTE: the asterisk (*) indicates the different numbers, letters or words, such as FontCache-S-1-5 - 21.dat or COFFfntCache.dat.

  Delete the cache of Photoshop police

  1. Release of Photoshop and the creative cloud (if installed) desktop application.
  2. Navigate to the appropriate folder
  • Photoshop CS6 and earlier versions.
    Windows XP: \Documents and Settings\Local Settings\Application Adobe application
    [Windows 7: \Users\[user name] \AppData\Local\Adobe
  • Photoshop CC and CC 2014
    [Windows 7 and 8: \Users\[user name] \AppData\Roaming\Adobe\Adobe Photoshop CC or CC 2014

  3. delete the TypeSupport (Photoshop CS6 and earlier) or the folder of police CT (Photoshop CC and CC 2014) Cache and the empty the trash.

  
  

  Some links that I've been using...
  

  t http://blogs.Adobe.com/Crawlspace/2012/07/Photoshop-basic-troubleshooting-steps-to-fix-MOS - issues.html
  http://helpx.Adobe.com/Photoshop/KB/Photoshop-CS6-GPU-FAQ.html#troubleshoot
  http://helpx.Adobe.com/Photoshop/KB/troubleshoot-fonts-Photoshop-CS5.html
  

  To be updated for future visitors to this case, we discovered that the problem might be with a bug in Windows, so we downloaded the latest updates and are currently waiting for your comments. I'll update once more when some time has passed and we have confirmed whether the update has worked or not.

• Cannot start ip-virtualization in Win server 2008 R2 (server role terminal server) on ESXi 4.1 U1

  Need help, pls

  Cannot start ip-virtualization in Win server 2008 R2 (server role terminal server) on ESXi 4.1 U1. User terminal session or program receives no DHCP or static IP http://technet.microsoft.com/ru-ru/library/ee382306 (WS.10) .aspx.

  

  On ESXi 4.1 U1 hypervizor run configuration:

  1 win 2008 R2 Enterprise (10.0.0.3)

  Roles:

  Servises (RDS) (ON IP-virtualization) remote desktop

  2 win 2008 R2 Enterprise (10.0.0.2)

  Roles:

  -Domain services AD

  -DNS

  -DHCP

  3 win 2008 R2 Enterprise (10.0.0.1)

  Gateway Kerio Control 7.1.2

  Terminal server server events: looks like everything is good

  

  Is of the opinion that the reason can in that the server must be started in the virtual environment.

  Help, please!

  Have you tried to uninstall VMwareTools as test? I remember at one point that there was some question about VMwareTools and R2 IP virtualization...

  VMCI driver provided by the tools has been the question if I remember...

  / Rubeck

• ESX 3i is good to consolidate the Services Terminal Server?

  Hello people, I am new to VMware, we have a company with 15 servers 7 of them to run Terminal Server, we plan to use VMware to consolidate servers TS but I don't know it's possible with it. Can you please tell us. ?

  Thank you.

  Can't say anything bad

  In fact I myself with HP blades, and it was a tough decision between blade and rack servers. Grid candidates were 380 and 580.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• I have several new emails in the Inbox, but I'm unable to view or even see them?

  I have several new emails in the Inbox, but I'm unable to view or even see them?

  Hey CRB123,

  Thank you for being a part of the communities of Apple Support.

  If I understand your message, you see a badge that you have unread e-mails in your Inbox, but they are not appearing.  An easy way to separate the emails read from the unread macOS that Sierra is to click the button to filter in the list of messages, or sort by unread:
  

  • Activate the filters: Click the filter button at the top of the list of messages, click unread to display the list of available filters, and then select one or more filters. A check mark indicates a filter is active.

    

    If you use more than one email account in Mail, you can filter the Inbox into account - for example, only show emails from your iCloud account.

  • Disable an active filter: Click on the filter.

  • Disable all filters: Click the filter button .

    Mail remembers your filters and automatically applied the next time that you click the filter button to activate the filters.

  You can also sort the list of messages - just click on "sort by" at the top of the list of messages, then select an attribute, such as and a sort order. In a typical configuration, click on a column header.

  Mail for Mac: filter the list of messages in Mail

  If no unread messages, then I would like to confirm if you have emails unread looking webmail for your email account. If you see the unread messages in webmail, go back to the mail app, and then rebuild your Inbox:
  

  You may have to re-create a mailbox to update the list of the messages it contains. For example, if messages seem to be missing or garbled, or if you don't find any relevant messages when you search by using the entire Message search option.

  • Select a mailbox in the Mail sidebar, then choose BALL > rebuild.

  When you rebuild the mailbox for accountIMAP or Exchange messages and attachments stored on your computer are discarded and then downloaded again from the mail server to your Mac. Your mailbox is empty until the download is complete.

  Mail for Mac: rebuild the mailboxes

  Take care.