WEBVPN and AD group membership

Similar Questions

• AnyConnect tunnel-group automatic assignment without selecting any group-tunnel-group-list alias and user-group strategy.

  Objective is that the anyconnect user must select group-alias, so that when a user enters his username and password he must go to his political group and tunnel-group specific. as I removed this command in webvpn 'no tunnel-group-list don't enable '. This I can not connect (user does not authenticate).

  1 - my question is why his past does not?

  Solution:

  If I keep only a single tunnel-group by default and make several group policies and assign to each user with his specific group policy that it works. in user attribute means I have only question following the commands it works, but if I put "group-lock value test-tunnel" that it did not identify.

  Please explain why.

  WebVPN

  allow outside

  limit the cache-fs 50

  SVC disk0:/anyconnect-win-3.0.10055-k9.pkg 1 image

  enable SVC

  internal strategy of group test-gp

  attributes of the strategy of group test-gp

  VPN-tunnel-Protocol svc webvpn

  the address value test-pool pools

  username, password test test

  username test attributes

  VPN-tunnel-Protocol svc

  group-lock value test-tunnel

  Strategy Group-VPN-test-gp

  tunnel-group test-tunnel type remote access

  attributes global-tunnel-group test-tunnel

  Group Policy - by default-test-gp

  tunnel-group test-tunnel webvpn-attributes

  allow group-url https://192.168.168.2/test

  Yes, you have the right solution. You only need to create 1 group of tunnel and multiple group policy. Under the attribute of the user, you re then group policy of vpn that you want the user assigned too.

  You can also authenticate users against AD and configure ldap attribute map to map the user to a specific group policy automatically.

  Here is an example of configuration if you happen to have the AD and will authenticate against AD:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808d1a7c.shtml

  Hope that helps.

• 'Group membership' does not get assigned to the user

  Hello
  
  Currently, we are implementing the authentication of the external table through single sign-on (SSO) as part of our security.
  In our portal, we have columns username, groupname and businessunit.
  
  As part of the implementation, I created the initialization of authentication block so that it stores the user name in the USER session variable.
  
  Select the username from usertable where upper (username) = upper(':USER');
  
  Then, I created a block of initialization of authorization in order to set the groupname. For this I used
  
  Select "group", groupname from usertable where upper (username) = upper(':USER');
  
  Now, when a user opens a session in SSO mode the user is redirected to the dashboard and initialization authentication block seems to work very well the USER session variable displays the corresponding username. Now when the user clicks on 'My account' and see his membership in a group, may not see his name of group that has been defined in the groupname column in the userstable. My scenario is similar to
  
  username GroupName businessunit
  
  x users with power Marketing
  Users are financial Mega
  
  
  
  For example, when the user opens a session x, it should be able to see its membership in the power users group. In this case I could assign privileges to these groups through the administration screen and my security.
  
  Can you get it someone please let me know where I am going wrong?
  
  Thank you

  Hello

  Try the debugging session.
  When you log on to the dashboard checks if the value stored in the GROUP session variable. If there is no value, I think that the user permissions are overridden. Normally users defined in the repository are priority to those coming from authentication to the external table. Make sure that the user you logged in with is not part of the repository (DPR) and comes via authentication external table.

  Let me know if you have any other questions.

  Thank you

• I can't get mail and news groups to appear only a specific folder

  When I registered Thunderbird tonight I usually see the folder mail and news groups. Unfortunately, only a specific folder opens and I'm unable to click the windows tab and select this option. I restarted. Close Thunderbird and it does not work. Strange thing is that it works fine on my old old PC home computer. It's my Mac laptop which is problematic. Can you please help? I have important files that I need access ASAP.

  Hello

  To better help you with your question, please provide us with a screenshot. If you need help to create a screenshot, please see How to make a screenshot of my problem?

  Once you have done so, attach the file to screen shot saved to your post on the forum by clicking on the button Browse... under the box to post your reply . This will help us to visualize the problem.

  Thank you!

• Cats 1-1 and Skype group chat doesn't work do not

  I upgraded Skype since Friday and then none of group cats, that I already have updated and I can't send a message in them. I've also added to groups by other contacts while on a call to them, and the group is created, but it shows as a group of "Untitled" with 0 participants on my screen and no video or mic.

  In addition to this, when I'm on the Cat 1-1 some of my posts don't send not the contact will go into offline mode and 1 minute later, they come online and sends the message. I thought that this could well be the first contact, but happened to 4 or 5 people I speak now.

  I use Skype version 7.21.0.100

  The first three lines of /dumpmsnp are:

  MSNP: Connection data (MSNP24):
  * Status: NetStateDisconnected
  * Current server: s.gateway.messenger.live.com
  * Server registered: s.gateway.messenger.live.com

  Please can anyone help with a solution to these problems?

  Restart your computer in Safe Mode with network and then try to start Skype.

• WebVPN and remote VPN access

  Hello

  Is there a difference between WebVPN and remote VPN access or they are the same.

  Thank you.

  access remote vpn consists of

  -IPSEC VPN remote access. It is part of the ASA, no permit required, requires pre-installed Client from Cisco VPN IPSEC on PC

  -with AnyConnect SSL VPN remote access. It requires licensing of SSL VPN on SAA. AnyConnect client can be installed automatically on the PC with the launch of web.

  -with Essentials AnyConnect SSL VPN remote access. Beginning with ASA 8.2 (1), almost license $ 0. It's the same AnyConnect client as in the previous article, but it cannot be installed automatically with the launch of web. It must be previously installed as of Cisco IPSEC VPN client.

  -webvpn aka clientless vpn. It is a portal HTTPS which allows HTTP connections, file sharing, telnet, RDP and much more (with smart tunnels) resources without having to install a real client on the PC. It requires licensing of SSL VPN on SAA. It cannot be used if "AnyConnect Essentials" license is activated on SAA after 8.2 (1)

  Kind regards

  Roman

• WebVPN and remote vpn, ssl vpn anyconnect

  Hi all

  Differences between webvpn and remote vpn, ssl vpn anyconnect
  All require a separate license?

  Thank you

  Hello

  The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port

  send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address

  address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL

  Web-mangle that allows us stuff things in theSSL session.

  SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and

  envelopes vpn traffic in the ssl session and thus also an assigned ip address has the

  tunnel's two-way, not one-way.   It allows for the support of the application on the

  tunnel without having to configure a port forward for each application.

  AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.

  For anyconnect licenses please see the link below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Kind regards

  Kanwal

• WebVPN and anyconnect on the same interface

  Hello!!

  We have ASA 5520 firewall running with code.9.1 (2). We already have webvpn running on the firewall and has active users to use it. Now, the client came with a new requirement to configure firewalls on the same anyconnect. We have installed VPN more premium license.

  (1) is it possible to enable webvpn and anyconnect on the same interface. If Yes, what are the aspects we must consider to allow them both on the same interface?

  (2) how much webvpn and anyconnect vpn licenses should I do with my premium lincense?

  Please help on this.

  shver attached for reference.

  Best regards

  Sri

  Your peers licenses AnyConnect Premium gives you the right to access SSL VPN without customer and focused on the customer.

  Licensing is based on the concurrent users so regardless of the simultaneous dosing will work - as long as the number of connected does not exceed 100.

  Your site to site VPN IPsec does not count against this permission, but is rather against "Other peer VPNS" which does not require a separate license and is limited by the capacity of the ASA equipment (750 on your platform).

• ASA political anyconnect and default group policy

  Hello world

  ASA is configured with anyconnect tunnel group and anyconnect group policy.

  AnyConnect group policy for

  in ASDM to allow concurrent connections box inherit

  timeout in ASDM watch checkmark on inherit

  By default of exhibitions in political group or system default

  simultaneous connections show 3

  timeout idlle shows 30 mins

  Need to understand that when we create anyconnect group policy and we click on inherit means it will take the value of this field of

  default group policy?

  As above default group policy also indicates that it has simultaneous connections for 3 and if I change to 2 concurrent connections in anyconnect group policy

  then the Group anyconnect policy will take precedence over the default group policy?

  The default system policy also shows idle time-out of 30 minutes that means it disconnects the anyconnect session after 30 minutes?

  Concerning

  Mahesh

  You're right about the strategy of group by default. If you assign a simultaneous connection of different to your group policy for the anyconnect profile these settings will override default group policy. Any changes of setting that explicitly to any group policy on the system replaces what has configured the default group policy.

• What is main groups of work and home-group?

  
  Dear moderator,
  
  What is main groups of work and home-group?
  
  Best@regards
  Faruksao
  From Bangladesh
  

  Homegroup, you need windows 7 or a later version to use.

  Group work is part of a network, if your PC is part of a

• Group and the Group of the United Nations

  Hi all

  I'm doing a code can select all the objects,text blocks and layers and then group them all the (CTRL + A) +(CTRL+G) , then I'll add more steps

  After that, I want to make a group of the United Nations again (CTRL + A) +(CTRL+SHIF+G)

  I try with this code but I see a few layers not selected and ungrouped, can anyone help please

  var doc = app.activeDocument;

  doc.selectObjectsOnActiveArtboard ();

  newGroup = app.activeDocument.groupItems.add ();

  for (a = app.activeDocument.layers [0].pageItems.length - 1; a > 0; a)

  {

  app.activeDocument.layers [0] .pageItems [a] .moveToBeginning (newGroup);

  }

  Thank you very much

  app.executeMenuCommand ("selectall");   (CTRL + A)

  app.executeMenuCommand ('group');   (CTRL + G)

  app.executeMenuCommand ('separate');  (CAPS + CTRL + G)

• How can I cancel my membership Adobe Acropro and activate my membership Adobe Lightroom?

  How can I cancel my membership Adobe Acropro and activate my membership Adobe Lightroom?

  You may please check out the link below for instructions on cancellation.

  Cancel your membership creative cloud

  For more information you can contact the Support from Adobe by clicking on the link below.

  Contact the customer service

  Please make sure that you are connected to the right Adobe ID.

  Hope this will help you.

  Kind regards

  Hervé Khare

• Is there a way to get the list of hosts and its groups of belonging to the vCenter folder level in 5.5 web vsphere client plugin development?

  Hello

  I need to get the list of all hosts and its groups of belonging to the vcenter folder level.

  1. I created a view giving the extension point: vsphere.core.folder.monitorViews.

  2. After this step, I wrote the constraint as in my class of mediator,

  var ListConstraint:Constraint =

  QuerySpecUtil.createConstraintForRelationship ( _contextObject, 'childEntity');

  I was expecting a list of all child entities such as hosts, dc, cluster... But I have only the immediate child object which is only the Datacenter as my result.

  Is it possible to get all hosts and vCenter folder level Clusters because I need the entire list to vCenter (highest level).

  Other info:
  

  Object file has only two properties:

  1 childEntity - list of entities

  2 childType in-kind folder ('Virtual Machine', 'Data center'...)

  Is it possible to write a constraint specifying which list of childEntities I need using childType in.

  Example: Make Me childEntities that has a 'Host' and 'Cluster' childType but childType in doesn't have these two types.

  In addition, at this level, I could see the 'Associated objects' tab which has all the information I need, such as Clusters and Cluster tab hosts and host tab respectively.

  So, I think its possible to get this list to vCenter folder level.

  I have attached a screenshot representing the need. Kindly ignore the Conventions of naming in there since I edited the example comes with the sdk program.

  
  

  Query:

  1. How can I get the host and Cluster (table of relationship) list to vCenter folder level or even at the level of the vise.global.view?

  2. once I get this list, is it possible for me to manipulate that list and send the new list to IU?

  3. is there another way to do the same thing without the help of model classes and mediator?
  

  
  

  Pointers to this will be very useful.
  

  It is not possible to obtain all hosts a folder specific vCenter from a single query Data Manager.  You need to get the list of centers of data first and then get a list of data center hosts.

  It is best to make these repeated requests to the java level and return only the list that you want to the user interface.

  You can get all the objects in the host of the system with a simple query using a constraint with targetType = 'HostSystem', but you will need to eliminate those from other vCenter servers.  See how this chassis example queries all hosts the Java later in the getHosts() method: samples/chassis-app/chassisRackVSphere-service/src/main/java/com/vmware/samples/chassisRackVSphere/ChassisRackVSphereDataAdapter.java

  Another option is to use the vSphere Web Services SDK to browse vCenter. See the vSphere management forum for help on these APIs.  See this plugin of the sample using this SDK

  samples/vsphereviews/vsphere-wssdk-provider/src/main/java/com/vmware/samples/wssdkprovider/VmDataProviderImpl.java

• We were members of creative cloud and when the membership was to be renewed, we asked one month free. This leads to 2 accounts creative cloud on our page... a renewed and paid for and the other related to the temporary use.  How to get rid of the tempo

  We were members of creative cloud and when the membership was to be renewed, we asked one month free. This leads to 2 accounts creative cloud on our page... a renewed and paid for and the other related to the temporary use.  How get rid of the temporary use of a month?  They both have the same ID and both appear on the administration page.  Thank you.

  Please contact customer service to get this resolved.

• How can I add and synchronize groups and AD users after a successful installation?

  Hello

  Maybe I don't see the wood from the trees.

  I have successfully installed a working environment of the Horizon.

  Now, I would like to add a few new users and AD groups, so that they would be synchronized with Horizon Workspace.

  If I am logged on as admin-account on the portal of the workspace, and I can see the tab "users and groups".

  There, I also see synchronized users during the installation, I added.

  But how can I add and synchronize the users in my ad?

  Kind regards

  André

  AD synchronization is done automatically on the schedule that you specified during the Setup installation ad part. You can change it and thus force a manual synchronization. But it is done on the connector and not the ordinary administration portal. You access your connector by using https:// Connector_URL:8443