When I start my laptop, I get the screen of my password, however, my keyboard and mouse do not work

Similar Questions

• Keyboard and mouse do not work when connecting

  I have windows 7 and ubuntu 9.10 "multiboot". He had been working well, until I rebooted. I had just done a WinPE boot drive, and I wanted to test it.

  Now the keyboard and mouse do not work on screen or login in safe mode.

  Help, please

  LKGC?

• Keyboard and mouse did not work properly after the service pack 2 update

  key Board runs very slowly and mouse runs through the screen when it is used. Acer Aspire 5050-3371 came with Vista home

  Hello

  Do you use a touchpad or mouse wired / wireless?

  Your laptop is connected with laptop keyboard?

  I suggest you to check if the keyboard and mouse work will find in safe mode. Follow the steps that will help you perform the following checks:

  Method 1

  a. restart the computer.
  b. start typing the F8 key.
  c. you get early boot option window.

  For more information, see: the boot advanced (including safe mode) options

   

  After the entry into SafeMode Log in your user account and check if the keyboard and mouse are working.

  After you perform method 1 Troubleshooting and if you find the keyboard and the mouse does not work correctly then you can perform the following procedure.

  Method 2:

  You can also perform the clean boot and check if you are able to start successfully. Clean boot will start Windows Vista by using a minimal set of drivers and startup programs and helps eliminate conflicts of third party software.

  The following link has steps showing how to perform the clean boot: http://support.microsoft.com/kb/929135

  Note: Please make sure that the computer is configured to start as usual according to step 7 of the article: how to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7:http://support.microsoft.com/kb/929135.

  Hope the helps of information. Please post back and we do know.

• Windows 7 - USB keyboard and mouse do not work once Windows starts

  The following happens occasionally:

  The keyboard works perfectly in the BIOS, the post OFFICE and when the Windows 7/64 Ultimate starts (I can tell the [Numlock] led shines). But when you see the Windows login screen, both, USB keyboard, USB mouse and stop working.

  I can say this from the [Numlock] LEDS go off and, mouse and keyboard, does not.

  There is no discernible specific deadline. Even wait minutes does not get the mouse or the keyboard back from work. In this case, the only way to get both mouse and keyboard, back from work is to reset the machine.

  I noticed this strange behavior with several keyboards, mice and different motherboards. So, it doesn't seem to be a problem related to a particular device.

  Independent since I also noticed the following:

  • I am currently using a card mother GIGABYTE Z68XP-UD3-iSSD. If I activate XDR (caching system with the small SSD disk) then Windows 7 starts up very quickly but keyboard and mouse get disabled for about 5 seconds when the login screen appears.
    .
  • During the installation of Windows, the keyboard rarely has not activate during the POST at all.

  I noticed that several people share the same problem. Is this an inherent problem USB HID? Or is there a bug in Windows that should be fixed?

  Hello

  This might be a question of power, where Windows is shutting off the power to your USB ports. Try this:

  Open the Device Manager
  Click on the tree "Universal Serial Bus".
  For each "USB root hub" do the following-
  Right-click on 'USB hub root'
  Select Properties
  Click the power management tab
  Make sure that the box "Allow the computer to turn this device to save power" is NOT checked.

  Try restarting now. If all goes well, that will take care of the issue.

• When I start my laptop I get the RunDLL error - wintwl32.rom

  What registry is corrupted, and how to fix it. Also why it seemed at first.

  Hello

  Cannot find this file on Google so you probably dodged some software malware and you should do a
  very thorough control. Message on how to remove the error message if still it y
  After the audits of malware.

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often
  easy to detect malicious software often comes with a much harder to detect and remove the
  payload. So its best to be now too thorough than paying the high price later. Check
  with an extreme overdose point and then run the cleaning only when you are very
  that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap you start, however, you should
  also run in regular Windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/products/malwarebytes_free

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with the other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here or
  Use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  -----------------------------------

  Original version is now replaced by the Microsoft Safety Scanner
  http://OneCare.live.com/site/en-us/default.htm

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  ----------------------------------

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing system
  files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

• Computer laptop keyboard and mouse does not work (updated Bios and took the batttery)

  I have HP G60-530US.
  
  I read all the posts that talked about updating the BIOS and then by doing a hard reset by removing the power cable and speaking on the battery and then hit the power button for a minute or simply to leave the computer for several minutes.
  
  A lot of people seems to have solved their problems.  Not me.
  
  I updated the BIOS and also did the hard reset like 10 times.  What other options are there?
  
  I have Windows 7-64 bit.  This problem occurred after I did the updates windows 11/04/13 or 12/04/13.
  
  Mouse power switch and the power button wifi button keys are the only ones that seem to work.

  Hello

  Go back to the device, right click on the Device Manager and select uninstall - when it is finished, restart the laptop.

  Any change?

  Kind regards

  DP - K

• Keyboard and mouse does not work / computer does not start

  I have a HP Pavilion a6403w that my daughter uses to the school. One day, the computer stopped boot-up.

  I get to the blue screen to choose (F10 = Setup) ect... The only key that seems to work at all is the F-10. If I press it, the computer responds by indicating it's to enter the configuration mode (but only if I press it very shortly after you turn on the machine), but the computer is hang.

  I can't get into safe mode.

  I put the recovery disk and turn on the machine, but nothing.

  I'm at a loss... any help would be great!

  Thank you.

  Stick with the HARD drive. Ask them to send it to you.

• I have a Canon MG6120. When I start it up I get the error code 5050. Does anyone know how to fix this?

  I have a Canon MG6120 all-in-one. When I start it up I get the error code 5050. Does anyone know how to solve this, more power to the wide / power?

  Hello gregg.

  Please, try the following to see if we can solve your problem:

  1. turn off the printer.

  2 disconnect the power from the printer for at least 5-10 minutes.

  3. once unplugged, remove any paper from the device.

  4. check for obstructions in the paths of the unit or the paper.

  5 If no obstacles are, plug the power back in and switch on the device.

  If the problem persists, the unit will require repairs for the correction.  We apologize for the inconvenience.  Please contact our support group using the 'Contact us' below for further assistance.

  It has not responded to your question or problem? Find more help at the Contact Us.

• When I start my computer, I get a screen that tells me the EULA has expired and I need to call the computer of the company rented to renew, however is not a rental?

  When I start my computer, I get a screen that tells me that the CONTRACT has expired and I need to call the company, that the computer can be rented to renew, however is not a rental? I have no idea what this same refers to, however, it gives me a password to enter, tells me that I have to wait 10 minutes, then it resets a chipset and allows the computer to, and then starts. I can't even take a screenshot of this message, because what it comes to control over the computer. I've scabbed virus and comes back clean. All this shows is a name of agent: HLZR4G1, then the Version 5.6.5 (Build-a-1028). The password was Wanker that seemed fishy, now the password is numbers and letters. Can someone explain this to me?

  Hello

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  make it work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Windows 7 64 bit worked very well and when was time to save I get the cyclic redundancy check, I try several times and made the same thing I need help please

  worked very well and when was time to save I get the cyclic redundancy check, I try several times and made the same thing I need help please

  Hello Hans,.

  Thanks for choosing Microsoft Community!

  According to the description of the problem, you have problems when you use the backup on Windows 8 feature.

  Please answer these questions to better understand the issue and help you:

  1. are - what you're talking to backup and restore functionality on Windows 7?

  2 have you made any changes to the computer before the show?

  It is perhaps to cause bad sectors on the hard drive, run the disk check to repair bad sectors

  Check your hard drive for errors:

  http://Windows.Microsoft.com/en-us/Windows7/check-your-hard-disk-for-errors

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  For more information:

  Backup and restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/back-up-and-restore-frequently-asked-questions

  Hope the helps of information. Don't answer if you need assistance, we will be happy to help you.

• I can't refine edge to work in 2014 of CC.  I select the mask, do the steps required to refine the mask and get a negative icon, a circle with a slash, and it does not work.  I used refine edge before and it has always worked.  This happened on fo

  I can't refine edge to work in 2014 of CC.  I select the mask, do the steps required to refine the mask and get a negative icon, a circle with a slash, and it does not work.  I used refine edge before and it has always worked.  This has happened for a while.  Very frustrating!

  Adobe Creative Cloud to edge CC>

• Keyboard and Touchpad do not work on my Samsung laptop.

  Original title: help

  keyboard and touchpad do not work in my computer samsung laptop... can you help me how to activate it? / Thank you

  Thanks for your reply. I did refresh the system and its working now. TNX again...

• Internal keyboard and mouse do not randomly respond time forcing me to restart my laptop 15 times until it works again

  1. sometimes this feedback haptic on the mouse is not triggered, leaving me by clicking on the mouse, while feeling against nature - something that is not supposed to happen

  2. after I close my laptop / closing of the lid/Eve (do not turn it off) the keyboard and the mouse literally don't work - it forces me to restart my laptop several times (sometimes around 15, take me 5-10 minutes just to get my laptop to work)

  Additional details:

  -J' tested a USB keyboard and mouse with my laptop and it works perfectly, even when the internal don't - maybe it's a hardware problem?

  -I went to the apple store a few weeks ago and spoke to someone at the "Genius Bar," which really helped at all - he told me I have to restart my laptop every time I open and I should do another user account - although I was skeptical about the logic used to arrive at these "solutions" I tried them anyway , here we are with the same problem - also, I don't have to close my laptop down 15 times every time I want to use, it's ridiculous, and that's why I bought a mac rather than a pc.

  -I'm not running any software/battery intensive programs on my laptop - especially just the word and the Google Chrome, which is not a lot

  -Here is a link to a video I downloaded from google reader showing how ridiculous, it's... https://drive.Google.com/open?ID=0B4oQ4C8NCLcWTWo5aVlrbDE1QmM

  Questions

  -I don't think that a fix is quite likely, but any suggestions are welcome!

  -Can I bring to the apple store and require a replacement? I left two years of care of apple

  This is probably in the wrong category, I apologize in advance - but it is a really weird problem that I don't think has a solution. Nevertheless, thank you for the reading of my rants and seizure of your advice!

  One thing that causes the mouse further trolling, is if your CPU is completely consumed by something. This can be checked in activity monitor CPU (all processes).

  Two other things can keep your Mac to be properly adjusted:

  GPU is suspended. These are cases where the GPU is no longer and can usually be seen in the console log, with symptoms such as GPU hang or WindowServer does not.

  Disk crashes.

  For the rotation of the discs, this can be a sign of imminent death of player.

  For SSDS of spare parts, this can be caused by the accumulation of deleted blocks, used in activating do not trim for your third-party SSD drive.

  -------

  The reason of suggests that you create a new user id is as a check against the clogging of a particular userid with junk that keeps things from being reactive. [a new user id will not have it clutter accumulated, so can react differently. He is not really a solution, it's a diagnosis.]

• HP PAVILION DV9000 WITH VISTA 64. KEYBOARD AND MOUSE NO LONGER WORKS AND CANNOT FIND THE DRIVERS. ANY SUGGESTIONS

  HP PAVILION DV9000 WITH VISTA 64. KEYBOARD AND MOUSE FOR LAPTOP DOESN'T WORK ANYMORE AND CAN NOT FIND THE DRIVERS. ANY SUGGESTIONS OF HOW I CAN RESTORE THESE?

  I had the top plug a mouse and external keyboard to access my laptop that works.

  Hello

  ·        What is the specific name of the laptop?

  Check if an error code or error message is listed in the Device Manager.

  a. Click Start, type devmgmt.msc and press to enter.

  b. expand the device and double click on the sub element.

  Here is the link to the HP website to download the drivers for the keyboard and mouse, look for the specific model number and download the drivers for the same thing: http://h20000.www2.hp.com/bizsupport/TechSupport/ProductList.jsp?lang=en&cc=us&taskId=135&prodSeriesId=1842187&prodTypeId=321957

  You can uninstall the drivers for the keyboard and the touchpad and install the drivers from the link above or let the update of Windows install the drivers for the device:

  a. Click Start, type devmgmt.msc and press to enter.

  b. expand the device and right click on the sub element and click on uninstall.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• When I start my computer, I get the message "runner error invalid BAckWeb application id 137903" what is it and how can I fix/get rid of it?

  Runner error invaldi 137903 backweb application ID

  Runner error invaldi 137903 backweb application ID

  You can have an application antivirus or antimalware too aggressive.  Which do you have?

  See: http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c00061410

  I suggest NOT to take advice of HP to make an "HP System Recovery".  If you are unable to uninstall HP or Compaq connections, you can probably prevent the error message by disabling the application HP Backweb to start as follows:

  Removes the AutoRuns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Install and let it scan.  When the analysis is complete, click the 'connection '.  Examine the entries in the tab log for an entry which seems related to the Backweb or HP or Compaq connections connections.  If found, clear the check box for this item.

  Restart and confirm that the error message does not appear.

  If you cannot determine which of the no doubt several items related to HP is the culprit, uncheck half of them and restart.  This repeatedly until you identify the startup item that is causing the error message.

  In AutoRuns, leaving an unchecked item prevents him from starting automatically at startup, but you can restore the automatic start simply be rechecking the box.  Once you determine you want to never see again the question, you can remove it.