When I try to connect to my Wordpress admin, Firefox limited me to 18 characters in the password box.

Similar Questions

• I have an Airport Express, which gives an unexpected error message when you try to connect to an existing network of WEP.  Any ideas.  Tried the factory returned. He was knocked offline when someone dug into the telco cables.

  I have an Airport Express, which gives an unexpected error message when you try to connect to a router WEP (Verizon) existing iOS9.3.2

  It flashes orange, but can not be reconnected to the router or to the title of the Setup Assistant or Airport utility.  Is there a way to reconnect to WIFI or should I bite the bullet and connect via Cat5e and be done with it.  My VPN works much better without AirPort Express connected.

  Sorry, but there is no WEP settings AirPort Utility on the iPhone or iPad, or any Mac version of AirPort Utility which was used for the last 4 years or so.

  If you have an older Mac still running AirPort 5.x utility or a PC with the AirPort for Windows utility installed on the device, the WEP settings that could be used to get the Express to connect to a WEP network there.

  As you know, WEP has not been secured for a number of years, and there are any number of free utilities available on the Internet, which is crack a WEP network in a few seconds. Thus, all those who want to be on your network will not have problems to do very quickly.

  But it's your call.

• When I try to connect to my wifi it says limited access and it was working fine yesterday I don't know what's happened can someone help me please

  I tried everything and nothing work please help me this is not the wifi area, I cause I can go on the internet with my xbox

  Louis

  • You have a good signal for your WiFi?
  • Recent changes to your system?
  • Have you recently purchased any product 2.4 GHz can cause interference?

  You can try and uninstall the device and reinstall and make sure your driver is up to date follow the instructions below:

  1. click on Start and type devmgmt.msc, then Enter. The Device Manager window opens.

  2. expand network adapter.

  3. right click on the wireless network card and select Uninstall.

  4 restart the computer. Windows must now install the drivers itself.

  5. put up-to-date drivers in the same way but selecting put updated driver

• Error message when turn on computer so very strong and high beep for a minute, already entered in the password box and typing of characters is uncontrolled.

  When I turn on my computer an error message flashes but it's too fast to read, after which there is a strong and high slope beep. Then he'll ask me if I want to start my computer on Vista or run the memory diagnostics. When it gets to the entered password there are already characters and trying to type at other times the space key is out of control.

  I have run memory diagnostics and the computer to the factory settings of disks that I made, but it has not worked and I was just wondering if anyone knew how to fix?

  Thank you

  http://www.helpwithpcs.com/upgrading/post-beep-codes.htm

  http://www.computerhope.com/beep.htm

  If sounds like you have a hardware problem.

  Check the links above to find an explanation for the error "" beep ".

  See you soon.

  Mick Murphy - Microsoft partner

• The FTP folder error when you try to connect to a folder on my Web server

  When I try to connect to a folder on my server using Windows Explorer, I get the following message...

  "Windows cannot access this folder.  Make sure that you typed the filename correctly and that you are authorized to access the folder.

  Details:
  A connection with the server could not be established.

  In the knowledge base, kb/260156 says it's because of me having reserved characters.  However, my password has no reserved characters.

  Can anyone help with this?

  Graham

  Hello
  I suggest you according to the question in this forum and check if that helps:

  http://social.technet.Microsoft.com/forums/en/winservergen/

  It will be useful.

• When you try to connect to internet it sometimes makes other times it doesn't.

  Sporadic internet connection

  My friend has a very annoying problem with the PC! When you try to connect to internet it sometimes makes other times it doesn't.
  The desktop pc is connected to the router/modem (D-Link WIFI ADSL 2 + G6242) via the ethernet cable, it communicates with the router, but
  not between the router and the net!
  I can connect without problems with laptop wireless, which indicates that the problem is with the Office
  and not the router!
  I suspect that the Office might be infected with malicious software. I've updated all the thing and run Malwarebytes, Spybot
  Search and destroy and Avast AV, nothing malicious is reported.
  I have restored to previous restore points, but the problem persists. It may be a corrupt file but which!
  I would have preferred to resolve this problem, otherwise I'll have to do a restore of the system Dell Factory!
  I'd love to help with this problem appreciate.

  Specifications of the PC;
  PC is connected to the router/modem (D-Link WIFI ADSL 2 + G624T)
  REB PC
  Computer:
  Computer Type ACPI (Mobile) 86 x PC
  Operating system Microsoft Windows Vista Home Premium 6.0.6002 (Vista RTM)
  Date: 2010-04-26
  Time 16:19
   
  OS Service Pack Service Pack 2
  Internet Explorer 8.0.6001.18904
  DirectX DirectX 11.0
  Motherboard:
  CPU type DualCore AMD Athlon 64 X 2, 2600 MHz (13 x 200) 5000 +.
  Card mother name Dell Inspiron 531
  Motherboard chipset nVIDIA nForce 6100-4xx, AMD Hammer
  Memory 2048 MB (DDR2 - 667 DDR2 SDRAM) system
  DIMM3: Hynix HYMP112U64CP8-Y5 1 GB DDR2-667 DDR2 SDRAM
  DIMM4: Hynix HYMP112U64CP8-Y5 1 GB DDR2-667 DDR2 SDRAM
  Type of Award BIOS (09/11/07)
    
  Display:
  NVIDIA GeForce 8300 GS (128 MB) video card
  NVIDIA GeForce 8300 GS (128 MB) video card
  Accelerator 3D nVIDIA GeForce 8300 GS
  Monitor Dell E207WFP (digital) [20 "LCD] (YM30682B6CFL)
    
  Multimedia:
  Audio adapter Realtek ALC888/1200 @ nVIDIA nForce 6100-400/405/420/430 (MCP61) - High Definition Audio Controller
    
  Storage:
  IDE controller NVIDIA MCP61 Serial ATA Controller
  IDE controller Standard dual channel PCI IDE Controller
  Storage controller Microsoft iSCSI Initiator
  Hard drive WDC WD50 00AAKS-75YGA SCSI Disk Device (465 GB)
  PBDS DVD +-RW DH - 16W1S SCSI CdRom Device optical drive

  Network:
  Main IP 192.168.1.2
  Primary MAC address
  Network card NVIDIA nForce Networking Controller)
    
   
  DMI:
  DMI BIOS vendor Dell Inc.
  DMI BIOS Version 1.0.7
  DMI system manufacturer Dell Inc.
  DMI system product Inspiron 531
  The system DMI 00 version
  DMI system number 5NNFJ3J
  DMI system UUID 44454C4C-4E00104E-8046B5C0-4F4A334A
  DMI Motherboard manufacturer Dell Inc.
  DMI Motherboard product 0RY206
  [NVIDIA nForce Networking Controller]
    
  Properties of the network adapter:
  Network card NVIDIA nForce Networking Controller
  Interface Type Ethernet
  Hardware address
  Connection connection to the Local network name
  100 Mbps connection
  MTU 1500 bytes
  DHCP lease obtained 26/04/2010 16:01:26
  DHCP lease expires 26/04/2010 17:01:26
  Bytes received 3931673 (3.7 MB)
  Bytes sent 279120 (272.6 KB)
    
  Network adapter addresses:
  IP / subnet mask
  Entry door
  DHCP
  DNS
    
  Manufacturer of the network adapter:
  Company name NVIDIA Corporation
  Product information http://www.nvidia.com/page/mobo.html 
  Download driver http://www.nvidia.com/content/drivers/drivers.asp 
  Update drivers http://driveragent.com?ref=59

  That's what shows in ipconfig/all, when it does not connect to the internet.
  Although I can connect with laptop computer when this happens on the desktop!

  Microsoft Windows [Version 6.0.6002]

  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\>ipconfig/all

  Windows IP configuration

  Name of the host...:-PC
    
  Primary Dns suffix...:
    
  Node... type: hybrid
    
  Active... IP routing: No.
    
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
    
  ... Description: NVIDIA nForce Networking Controller
    
  Physical address.... : (I have hidden for security)
  DHCP active...: Yes
    
  Autoconfiguration enabled...: Yes
    
  Autoconfiguration IPv4 address. . : 169.254.163.97 (Preferred)
    
  ... Subnet mask: 255.255.0.0.
    
  ... Default gateway. : 0.0.0.0.
    
  NetBIOS over TCP/IP...: enabled

  C:\Users\ >

  Of course, it does not show what it should show such as;

  Lease obtained...:
  Expiry of the lease...:
  ... Default gateway. :
  DHCP server...:
  I tried to reset with the following commands unsuccessfully;

  Start, all Programs\Accessories and right click on command prompt, select "run as administrator" to open a command prompt.

  In the command prompt window, type the following commands, each followed by the Enter key:

  Reset the battery TCP/IP IPv4 default installation. netsh int ipv4 reset reset.log

  Reset the battery TCP/IP IPv6 default installation. netsh int ipv6 reset reset.log

  Reboot the computer.

  Microsoft Windows [Version 6.0.6002]

  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Stebex>ipconfig/all

  Windows IP configuration

  Name of the host...: Stebex-PC
    
  Primary Dns suffix...:
    
  Node... type: hybrid
    
  Active... IP routing: No.
    
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
    
  ... Description: NVIDIA nForce Networking Controller
    
  Physical address.... : 00-1A-A0-80-67-76
    
  DHCP active...: Yes
    
  Autoconfiguration enabled...: Yes
    
  Autoconfiguration IPv4 address. . : 169.254.163.97 (Preferred)
    
  ... Subnet mask: 255.255.0.0.
    
  ... Default gateway. : 0.0.0.0.
    
  NetBIOS over TCP/IP...: enabled

  C:\Users\ >
  Would appreciate help please!

  Problem solved by a relocation complete!

• I had to have an iphone 4, but is unable to operate in Italy. It is supposed to be unlocked by Apple and O2, but when I try to connect with wind or Tim there is no service. What should I do?

  I had to have an iphone 4, but is unable to operate in Italy. It is supposed to be unlocked by Apple and O2, but when I try to connect with wind or Tim there is no service. What should I do?

  Maybe it is locked, Apple do not unlock phones, then call O2.

• I have an internet connection, but when I try to enable Thunderbird software appears on my desktop screen, but could not complete the connection process.

  I have Thunderbird installed on my desktop and laptop. So far, it worked very well on both machines. Today, when I try to activate the Thunderbird, the software on my desktop and laptops come on the screen, like the "sign-in" box When I try to connect, however, the process hangs part way through and the circle around the rotation shows that the activity occurs. Finally Windows 7 on the laptop tells me that the program is not responding.

  The same result occurs on two machines, the desktop and the laptop. I checked and I have an active internet connection on both machines.

  What should I do?

  John Gardner

  There is no right or wrong with using POP or IMAP. It really depends on what you're trying to reach. There is a lot of information on the web about POP or IMAP, here is an example.
  http://www.howtogeek.com/99423/email-whats-the-difference-in-POP3-IMAP-and-Exchange
  For more information on the transfer of data to a new profile, see this article. But I guess you have already covered everything you need.
  http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Thunderbird

• Since the installation of El Capitan, I can't connect to shared on the network computers. I can see them, but when I try to connect it says connection failed. I can connect directly in Parallels using a shortcut.

  I can't connect to shared network computers. Not a problem already before the update to OS X El Capitan. The computers appear in the Finder under heading Shared, but when I try to connect it says connection failed. However, under Parallels Windows 7 I can properly connect via the shortcut or mapped drive. Any suggestions?

  El Capitan is a bit fussy about safety. Try

  Finder > go > connect to server...

  and enter the address of the server explicitly in the dialog box that appears.

  C.

• When you try to connect to a Yahoo link, like yahoo mail, I get (error code: ssl_error_bad_cert_domain)

  This connection is Untrusted

  You asked Firefox to connect safely to we - mg5.mail.yahoo.com, but we cannot confirm that your connection is secure.

  Normally, when you try to connect safely, sites will present a reliable identification to prove that you're in the right place. However, the identity of this site cannot be verified.

  You use a bookmark to open this link?

  If you then try to open the page https://mail.yahoo.com/ instead and, possibly, change the URL of the bookmark to delete the foreground we mg5

  It is generally not a good idea to bookmark the pages directly as long as such links to specific areas can become valid.

• When I try to connect it to my sync account, he said that there is no such user.

  When I try to connect it to my sync account, he said that there is no such user. I don't want to save again, as this is a perverse way to the creation of duplicate accounts. I also have an account password file to keep track of user login data: user name, email address, password, so it's not a matter of just forget the name of account etc. I've just updated to 29 of Firefox, this could be a coincidence.

  I use windows 7, with the latest updates and patches.

  29 Firefox introduced a new synchronization mechanism. This new system has existed only for about 2 months, so it is likely that you have actually not account. You can see the information for the new synchronization here: synchronize bookmarks of Firefox, history, passwords and more.

• I had to change my password online gmail accnt and now I get a msg "configuration could not be verified" when I try to connect with the new password.

  I had to change my password for the gmail online account. I can access my account with the new password through my browser and my cell phone. But when I try to connect to my gmail account in Thunderbird
  by using the new password, I get a "Configuration could not be verified" error message.
  Any help would be appreciated.
  Thank you
  Brendan

  It looks like you are trying to create a new account. What are you doing exactly?

• Error 1003: I get this error when you try to connect to a Web site. I have revived the iPad and was able to do, however, when I left the game I got error 1003. I tried

  Error 1003: I get this error code when I try to connect to a Web site. I have revived the iPad and was able to do, however, when I left the game I got error 1003. I tried to reconnect and automatically received this error message. This happens with all browsers on my iPad. I deleted the cookies, cache, etc, it may not always connect. Help, please.

  You can try this by using a different connection? If possible cell or another location of WiFi?

  If it goes with several browsers - it's probably your network

• Keep gettig this error message when you try to connect to Firefox, the proxy server refuses connections.

  Redownloaded Firefox and keep getting this error message when you try to connect: proxy server refuses connections

           Firefox is configured to use a proxy server that is refusing connections.
  

   Check the proxy settings to make sure that they are correct.
   Contact your network administrator to make sure the proxy server is
     working.
  

  Go to Options > advanced > network > connection > settings, then choose 'no proxy '.

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

  Not related to your question, but...

  It is important that you keep updated IE. The information included with your question indicates that you use IE7; you need to update to IE8 for your own protection. IE9 will be available for Windows XP.

  • http://Windows.Microsoft.com/en-us/Internet-Explorer/products/IE/home

• I gave my Iphone update, he asked me my Apple ID but when I try to connect it says my Apple ID is incorrect, but I am logged in it from my computer, what should I do?

  I gave my Iphone update, he asked me my Apple ID but when I try to connect it says my Apple ID was wrong (it cannot be used to unlock my iPhone) but I am connected with it from my computer, what should I do?

  Post edited by: Lorayma12

  Most of the time that what happens when people change their email address main apple id without first signing in iCloud on their phone - the phone remains signed with the old e-mail address. Here's the latest from apple If you can not activate your iPhone, iPad or iPod touch after installing iOS 9.3 - Apple Support

  If you can connect to iCloud.com AND see your phone under appliances, you can remove the account as a last resort.