Why do I have a Spinning beachball when waking from sleep?

Similar Questions

• Repeated restarts when waking from sleep

  I have a MacBook Pro OS 10.10.5. The computer was started by browsing sometimes restart several cycles when waking from sleep. When this happens, I don't me the login screen. I held down the power button to turn off the computer, and then restart. About 6 weeks, the original internal hard drive has failed and was replaced by a SSD drive. But the problem didn't start until a few days ago. There were no other change in hardware or software. The computer is connected to an external monitor and external power is all the time, except when I travel or deliberately to drain the battery for maintenance. I checked the various discussions, but could not find any solution accepted to this problem.

  Start - computer restarts by itself-Yosemite

• iMac is suspended when waking from sleep

  When I return to my iMac 21 inches for the wakes, I get my password from the screen and it does nothing but display the spinning beachball. It remains this way for an indefinite period. The only way out, as far as I know, is to do a power of the force down (hold the power button for 10 seconds) and the power it upward. Otherwise, everything works fine. Any suggestions on what to check?

  Please read this message before doing anything.

  This procedure is a diagnostic test. It is unlikely to solve your problem. Don't be disappointed when you find that nothing has changed after you complete it.

  The test is intended to determine if the problem is caused by a third-party software that loads automatically at startup or logon, by a device, by a police conflict or corruption of system files or some system caches.

  Disconnect all devices wired except those required to test and remove all the expansion cards from secondary market, as appropriate. Start in safe mode and log on to the account of the problem.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, with limited graphics performance, and some things work at all, including an audio output and a Wi - Fi connection on some models. The next normal boot can also be a bit slow.

  The login screen is displayed even if you usually connect automatically. You need your password to log on. If you have forgotten the password, you will have to reset it before you begin.

  Test in safe mode. Same problem?

  After testing, restart as usual (not in safe mode) and make sure you always have the problem. View the results of the test.

• HP Envy X 2 touch screen not responding do not when waking from sleep

  About half of the time when I wake up my HP envy X 2 version sleep 128 GB touchscreen is unresponsive. The mouse pad and the keyboard usually work but screen tousch work again until it is restarted.

  I took a peek in the Device Manager, while the touch screen did not work and I don't see under User Interface devices, I have a HID I2C device that has a yellow warning sign. When I open it under device status, it says "Windows has stopped this device because it has reported problems. (Code 43) »

  Someone at - it information on how to solve this problem?

  I had already tried to upgrade the Synaptics drivers and it does not solve the problem.

  I noticed several times that when I wake the PC from sleep that Google Talk would be stuck with about 40% of the use of processer according to the Task Manager. I usually just close and re - open Google talk and he would not stuck using the processor.

  A couple of days ago I closed Google Talk and did not restart the program, during the last 2 days I didn't only once when the touch screen has been non-responsive after waking up from his sleep.

  I've said before, but I had a similar problem with the rotation sensor, after waking up from his sleep, he would be intermittenetly does not work and I could also see in Device Manager that another I2C HID device was a code 43 error. Also since the closing of google talk, I didn't freeze the rotation sensor.

  Like I said its only been a couple of days, so it can always happen, but 2 days is the longest I can remember never go without this problem.

  mfhengst, you have google talk installed on your laptop?

• Computer Vista freezes / crashes when waking from sleep/hibernate. I installed the latest drivers. Any thoughts?

  I also checked the event viewer, and it has a critical error.  Kernel-power of the source.  Event ID 41.  General description: "the last sleep transition was unsuccessful.  "This error can be caused if the system unresponsive, failed, or power during the transition from sleep loss."  Does anyone have an idea as to what this may highlight or where to look next for more information?

  Hi Helpme_971,

  1. did you of recent changes on the computer?

  You can try these steps and see if it helps.

  Method 1:

  Step 1:

  You can try to check if the problem occurs in safe mode.

  Start your computer in safe mode

  Step 2:

  If you are not faced with the question in safe mode, then you can try to perform a clean boot and see if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please refer to clean the boot link to put the computer to normal startup mode.

  Method 2:

  You can also check the following items and see if it helps.

  The problems of wake the computer from sleep mode

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista

  Hope this information is useful.

• Monitor shows erratic colors when waking from sleep

  Brand new Mac Mini, two monitors Dell, OS 10.11.3. The monitor which is connected to the Mini with a bolt of lightning > HDMI cable, when he wakes up from his sleep, sank about half the time the monitor changed to a purple that covers the entire screen. I see the desktop but everything is purple in color. If I disconnect the monitor for 10-15 seconds and turn it back on, the color scheme is usually back to normal. Can't get on the other monitor connected with a HDMI > HDMI cable.

  Only, I raised the issue here because my previous Mac Mini had video problems - both monitors would turn off randomly to black screens asking the full restart. Assumed a Mini hardware problem so I bought a new Mini and now I am having a problem of monitor again on the new Mini. (I remember reading a couple of years on the problems of video/monitor on Mac mini).

  Question: before concluding it is a hardware of the monitor problem, are there any known issues with a bolt of lightning > HDMI connection? I have not purchased and tried a new cable, but would that be a problem?

  A graphics display card problem?

  Thanks for the tips and suggestions.

  Hi, William.

  Please visit Apple support communities.

  I understand that you are having problems of color with a screen connected via Thunderbolt to HDMI.  If you have tried an adapter or an extra cable and the problem persists, try the troubleshooting steps in the article below.

  The Thunderbolt ports and displays: frequently asked questions (FAQ)

  See you soon

• When waking from sleep, the date changes to 2029

  Sometimes when my computer wakes up from being asleep, the date changes until 2029.  The month and day are the same, but the changes of the year.  I then have to set manually the date, the automatically sync with windows server doesn't fix it.  Its really annoying because then my anti-virus thinks its out of date as well as the update of windows.  My internet browser also has security due to date problems.  I can not understand what causes the date change 2029!

  Hello Nevik09,

  A possibility is that the CMOS battery is out. Did you replace the battery to determine if it could be a cause?

  Also, take a look at this thread on Technet for another possible solution. http://social.technet.Microsoft.com/forums/en/w7itprogeneral/thread/9d180368-35ee-4334-9cce-cd2b2c7f1f2a

  Hope this helps

  Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Mid-2015 15-inch Macbook Pro kernel panicked retina when waking from sleep

  This kernel panic to wake up a Mid-2105 15 - in retina Macbook Pro to sleep. He has been

  connected via the port of a HP E241i screen display. It happened several times.

  I've included below the stacktrace. I'm hoping to see if there are known issues/fixes for this model of Macbook.

  Anonymous UUID: DFA34557-7796-67BA-7F2E-AAAD330EDC04

  Mon Feb 15 13:45:30 2016

  Panic report *.

  panic (cpu 0 0xffffff8002616df2 appellant): Kernel trap at 0xffffff800230e11b, type 14 = page fault, registers:

  CR0: 0X000000008001003B, CR2: 0XFFFFFF81EBA07000 CR3: 0 X 0000000005473000, CR4: 0X00000000001627E0

  RAX: 0 X 0000000000000000, RBX: 0X000000000000030E RCX: 0 X 0000000000000220, RDX: 0X00000000180F0000

  RER: 0XFFFFFF81EB11BC88, RBP: 0XFFFFFF81EB11BD00, IHR: 0X0000000000002D00, RDI: 0XFFFFFF81EBA07000

  R8: 0 X 0000000000000024, R9: 0XFFFFFF8002BFB6D4, R10: 0X000000000000001A R11: 0 X 0000000000000023

  A12: 0 X 0000000000000004, R13: 0XFFFFFF81A0E48000, R14: 0 X 0000000000000002, R15: 0XFFFFFF81EBA05400

  RFL: 0 X 0000000000010206, RIP: 0XFFFFFF800230E11B, CS: 0000000000000008, SS 0 X: 0 X 0000000000000010

  Lack of CR2: 0xffffff81eba07000, error code: 0 x 0000000000000002, CPU error: 0x0

  Backtrace (CPU 0), frame: return address

  0xffffff81eb11b930: 0xffffff800252ad21

  0xffffff81eb11b9b0: 0xffffff8002616df2

  0xffffff81eb11bb70: 0xffffff8002633ca3

  0xffffff81eb11bb90: 0xffffff800230e11b

  0xffffff81eb11bd00: 0xffffff7f8374eee9

  0xffffff81eb11bd30: 0xffffff7f8476dd6e

  0xffffff81eb11be20: 0xffffff7f83750534

  0xffffff81eb11be60: 0xffffff7f8374f792

  0xffffff81eb11be90: 0xffffff7f8374b8e3

  0xffffff81eb11bef0: 0xffffff8002ad595d

  0xffffff81eb11bf40: 0xffffff8002ad37cd

  0xffffff81eb11bf80: 0xffffff8002ad38c6

  0xffffff81eb11bfb0: 0xffffff80026116e7

  Extensions of core in backtrace:

  (2.4.1) com.apple.iokit.IOGraphicsFamily [8922721D-5517-3883-BD3A-57422D0244A0] @0 xffffff7f83740000-> 0xffffff7f8377afff

  dependency: com.apple.iokit.IOPCIFamily (2.9) [BDA92C3B-AD86-33E5-A7F1-1603465350A7] @ 7f82d3d000 0xffffff

  com.apple.driver.AppleIntelFramebufferAzul (10.0.6) [7E7652B8-CBEF-3216-A12C-B7CF AA1D67D4]@0xffffff7f84768000-> 0xffffff7f847b2fff

  dependency: com.apple.iokit.IOPCIFamily (2.9) [BDA92C3B-AD86-33E5-A7F1-1603465350A7] @ 7f82d3d000 0xffffff

  dependency: com.apple.iokit.IOACPIFamily (1.4) [70E2B65E-A91A-3522-A1A0-79FD63EABB4C] @0xfffff f7f8365e000

  dependency: com.apple.iokit.IOAcceleratorFamily2 (156.16) [1259B80F-E4C5-3BC9-BED5-65B42289E8 C0]@0xffffff7f8465a000

  dependency: com.apple.iokit.IOReportFamily (31) [781C9DD1-4CE9-3AEB-85EA-D420CEC18916] @ ff7f83657000 0xffff

  dependency: com.apple.AppleGraphicsDeviceControl (3.10.25) [DFDCFB7E-74E4-397F-AA6F-6ECFC41D5 649]@0xffffff7f84761000

  dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [8922721D-5517-3883-BD3A-57422D0244A0] @0 xffffff7f83740000

  Corresponding to the current thread BSD process name: kernel_task

  Mac OS version:

  14F27

  Kernel version:

  14.5.0 Darwin kernel version: Wed Jul 29 02:26:53 PDT 2015; root:XNU-2782.40.9~1/RELEASE_X86_64

  Kernel UUID: 58F06365-45C7-3CA7-B80D-173AFD1A03C4

  Slide kernel: 0 x 0000000002200000

  Text of core base: 0xffffff8002400000

  Text __HIB base: 0xffffff8002300000

  Name of system model: MacBookPro11, 4 (Mac-06F11FD93F0323C5)

  Availability of the system in nanoseconds: 35568964195350

  last load kext to 8407315731: com.sophos.kext.sav 9.4.50 (addr 0xffffff7f82c46000 size 28672)

  Finally unloaded kext to 373748193372: com.apple.driver.AppleFileSystemDriver 3.0.1 (addr 0xffffff7f84b62000 size 8192)

  kexts responsible:

  com Sophos.kext.SAV 9.4.50

  com Sophos.nke.SWI 9.4.50

  com.github.osxfuse.filesystems.osxfusefs 2.7.4

  org.pqrs.driver.Karabiner 10.15.0

  com.credant.iomediafilter.CREDANTShield 6659

  com.credant.kext.CREDANTCrypto 4581

  com.sektioneins.driver.SUIDGuardNG 1.0.6

  com Apple.filesystems.autofs 3.0

  com.apple.driver.AudioAUUC 1.70

  com.apple.iokit.IOBluetoothSerialManager 4.3.6f3

  com.apple.driver.AGPM 110.19.6

  com.apple.driver.ApplePlatformEnabler 2.2.0d4

  com.apple.driver.X86PlatformShim 1.0.0

  com.apple.driver.AppleOSXWatchdog 1

  com.apple.driver.AppleGraphicsDevicePolicy 3.7.7

  com.apple.driver.AppleUpstreamUserClient 3.6.1

  com.apple.iokit.IOUserEthernet 1.0.1

  com.apple.driver.AppleHDA 272.18.1

  com.apple.Dont_Steal_Mac_OS_X 7.0.0

  com.apple.driver.AppleHWAccess 1

  com.apple.driver.AppleLPC 1.7.3

  com.apple.driver.AppleBacklight 170.7.4

  com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.3.6f3

  com.apple.driver.AppleHV 1

  com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

  com.apple.driver.AppleMCCSControl 1.2.12

  com.apple.driver.AppleThunderboltIP 2.0.2

  com.apple.driver.AppleCameraInterface 5.36.0

  com.apple.driver.AppleSMCLMU 2.0.7d0

  com.apple.driver.AppleIntelHD5000Graphics 10.0.6

  com.apple.driver.AppleIntelFramebufferAzul 10.0.6

  com.apple.driver.AppleTopCaseHIDEventDriver 67

  com.apple.driver.AppleUSBTopCaseDriver 67

  com.apple.driver.AppleUSBCardReader 3.5.5

  com.apple.driver.AppleUSBHub 705.4.2

  com.apple.driver.XsanFilter 404

  com.apple.iokit.IOAHCIBlockStorage 2.7.1

  com.apple.driver.AirPort.Brcm4360 930.37.3

  com.apple.driver.AppleUSBXHCI 710.4.11

  com.apple.driver.AppleAHCIPort 3.1.2

  com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

  com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

  com.apple.BootCache 36

  com.apple.driver.AppleSmartBatteryManager 161.0.0

  com.apple.driver.AppleACPIButtons 3.1

  com.apple.driver.AppleRTC 2.0

  com.apple.driver.AppleHPET 1.8

  com.apple.driver.AppleSMBIOS 2.1

  com.apple.driver.AppleACPIEC 3.1

  com.apple.driver.AppleAPIC 1.7

  com Apple.NKE.applicationfirewall 161

  com Apple.Security.Quarantine 3

  com.apple.security.TMSafetyNet 8

  com Apple.kext.Triggers 1.0

  com.apple.iokit.IOSerialFamily 11

  com.apple.driver.DspFuncLib 272.18.1

  com.apple.kext.OSvKernDSPLib 1.15

  com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.3.6f3

  com.apple.iokit.IOBluetoothFamily 4.3.6f3

  com.apple.driver.AppleBacklightExpert 1.1.0

  3.10.25 com.apple.driver.AppleGraphicsControl

  com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

  com.apple.driver.AppleSMBusController 1.0.13d1

  com.apple.driver.X86PlatformPlugin 1.0.0

  com.apple.driver.AppleSMC 3.1.9

  com.apple.driver.IOPlatformPluginFamily 5.9.1d7

  com.apple.driver.AppleHDAController 272.18.1

  com.apple.iokit.IOHDAFamily 272.18.1

  com.apple.iokit.IOAudioFamily 203.3

  com.apple.vecLib.kext 1.2.0

  com.apple.iokit.IOUSBUserClient 705.4.0

  com.apple.iokit.IOSurface 97.4

  com.apple.iokit.IONDRVSupport 2.4.1

  3.10.25 com.apple.AppleGraphicsDeviceControl

  com.apple.iokit.IOAcceleratorFamily2 156.16

  com.apple.iokit.IOGraphicsFamily 2.4.1

  com.apple.driver.AppleHIDKeyboard 176,2

  com.apple.driver.AppleMultitouchDriver 264,6

  com.apple.iokit.IOUSBHIDDriverPM 710.4.7

  com.apple.iokit.IOUSBHIDDriver 705.4.0

  com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.5

  com.apple.iokit.IOUSBMassStorageClass 3.7.2

  com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.5

  com.apple.driver.AppleUSBMergeNub 705.4.0

  com.apple.driver.AppleUSBComposite 705.4.9

  com.apple.driver.AppleThunderboltDPInAdapter 4.0.6

  com.apple.driver.AppleThunderboltDPAdapterFamily 4.0.6

  com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2

  3.1.7 com.apple.driver.AppleThunderboltNHI

  com.apple.iokit.IOThunderboltFamily 4.2.2

  com.apple.iokit.IO80211Family 730.60

  com.apple.driver.mDNSOffloadUserClient 1.0.1b8

  com.apple.iokit.IOUSBFamily 720.4.4

  com.apple.iokit.IOAHCIFamily 2.7.5

  com.apple.iokit.IONetworkingFamily 3.2

  com.apple.driver.AppleEFINVRAM 2.0

  com.apple.driver.AppleEFIRuntime 2.0

  com.apple.iokit.IOHIDFamily 2.0.0

  com.apple.iokit.IOSMBusFamily 1.1

  com Apple.Security.sandbox 300.0

  com.apple.kext.AppleMatch 1.0.0d1

  com.apple.driver.AppleKeyStore 2

  com.apple.driver.AppleMobileFileIntegrity 1.0.5

  com.apple.driver.AppleCredentialManager 1.0

  com.apple.driver.DiskImages 398

  com.apple.iokit.IOStorageFamily 2.0

  com.apple.iokit.IOReportFamily 31

  com.apple.driver.AppleFDEKeyStore 28.30

  com.apple.driver.AppleACPIPlatform 3.1

  com.apple.iokit.IOPCIFamily 2.9

  com.apple.iokit.IOACPIFamily 1.4

  com.apple.kec.Libm 1

  com Apple.KEC.pthread 1

  com Apple.KEC.corecrypto 1.0

  Uninstall this software:

  Sophos AV

  GitHub and OSXFuse

  Carabiner

  CREDANT shield/Crypto

  SektionEins driver and SUIDGrardNG

  One or more are at the origin of the crash. Start by removing Sophos. Since the graphics family is one of the problems, don't forget to remove anything you have installed which would be new for your use of the GPU.

  Be sure to use any uninstaller provided with the software. Something that comes with an uninstaller uninstall not manually.

• Sony Vaio laptop BSOD when waking from sleep. 8.1 64bits

  Hello

  My Sony vaio is strange. Whenever I put it to sleep and it wakes the BSOD while it recharges to the 'not found operating system". Now the power button down for 30 seconds and then it turning it back makes me back in the operating system without any problem.

  I've updated the BIOS and run that all pilots availible to do this and the model.

  I also reset the BIOS to the factory settings.

  I have also reinstalled the operating system.

  VPCSA290X

  Everything works well except the mode 'sleep'.

  Nobody has any ideas? OK, Im going to the customer and to recommend that he not spend a dime on Sony laptops in the future. His name is Dayne Sampson.

• Windows 7 is no longer asking for a password when waking from sleep

  Windows 7 has been asking password whenever the computer has been coming out of sleep, but he ceased to do this now. I checked and I still have this option turned on. I tried to change the password and not restarted still no change. Can any ideas on how I fix?

  Windows seems to be struggling to control this setting sometimes so you must check in three places to make sure it was taken correctly.

  1 set the screen saver - Panel, customize, Screensaver [in the lower right corner of the window]. You can change the time and whether or not sign it again after it also activates.

  You should then check the opening of session of this parameter in both part

  2 power options, [on the left side of the window] require a password on wake up

  3 power options, plan {power} active settings change, change of plan avancΘs, [you will have to click on "view the currently hidden settings] {active power plan}, require a password on wake up

  Steps 2 & 3 are simply verify that the change has been defined & saved - there should be no problem under normal circumstances.

• Satellite A100-049 screen remains empty when reactivated from sleep mode

  Intermittently, have been left for a while my screen A100-049 remains empty when reactivated from sleep mode. It does not meet the access keys and have checked the settings which seem to agree.

  Notice that in this case the power button remains 'blue' and not to return to 'Orange flashing. Is this a common problem?

  Hello

  What do you with the mode 'sleep'? Do you mean the hibernation mode or the mode booth? What operating system do you use?

  Listen buddy. It's really not easy to say why it happens without running diagnostic tests. I think you should try to update the graphics driver and check if you are using the latest version of the BIOS. Two updates might be useful in resolving these issues

  Good luck

• Why do I have a loud hum when with audio recorded when I read a file saved with Microsoft LifeCam with the latest version of Microsoft Essentials?

  Why do I have a loud hum as well as audio recorded when I play a file saved using Microsoft LifeCam with the latest version of Microsoft Essentials?

  HUMS are usually ground fault loops.

  If it is a test of laptop with and without the power connected (using battery instead)

  The mic can also have a cut wire, etc.

• Acrobat CC - Spinning Beachball when opening files

  I'm on OS 10.10.1 running Adobe Acrobat Pro DC 2015.007

  I noticed that whenever I open a pdf file (any file, any size or complexity) I get a spinning beachball for about 30 seconds before allowing to do almost anything.

  No alternative workaround for this or why it is happening?

  Hi TGMike,

  Please post on the Adobe forums.

  Please try to set the value to 1 under the label of Documents in recently used list in ' Edition > Preferences > Documents.

  Close and re-launch Acrobat.

  Let me know if it helps.

  Kind regards

  Ana Maria

• USB-232/4 causes Windows hang when wake from sleep

  I have a problem of resumption of the functioning of the laptop that follows "sleep" or "hibernate".

  With the connected USB-232/4, the computer does not return the Windows normally.  The display does not return (without backlight or external video output), but the LED indicators (bluetooth, disc, power, etc.) appear normal.  When I remove the USB from the USB-232/4, the display reverts immediately to the State before the mode 'sleep' activated.  Tried all 3 USB ports - all the same behavior.  No index by using the event viewer.

  Win 7 (64 bit)

  Series NI 3.7, NEITHER VISA NOR spy 2.7.2 5.0.2 MAX 4.8

  Serial port assignments seem to be OK:

  Port 1 - com15

  2 port - com9

  Port 3 - com16

  Port 4 - com8

  Any suggestions on the next steps to solve this problem?

  Thanks in advance.

  Solved the problem!

  The BIOS has a setting in the section advanced to Wake Up capability.  Compatible USB S3 Wake.  Now, the USB-232/4 is powered over the recovery of the standby mode.  When this feature is disabled, the USB-232/4 light not upon resuming from sleep mode and probably hung up the pilot, preventing a normal recovery.

• Why do I have a 'General' error when trying to connect to a site on my laptop, but my office works fine?

  After an update from Microsoft, I tried to connect to a gambling site, but all I get is a "General error". He told me to refresh the page and try again. When I go to my office, I have a problem to connect. Why? Desktop is running xp, computer laptop windows 7.

  You can try the following steps in case of problems with web pages:

  Reload Web pages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  Clear the cache and cookies only from Web sites that are causing problems.

  "Clear the Cache":

  • Firefox/tools > Options > advanced > network > content caching Web: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Firefox/tools > Options > privacy > Cookies: "show the Cookies".

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes