Why firefox fails during the upgrade?

Similar Questions

• Win7 fails during the upgrade of a Phenom II X 2 a X 4

  I am running Windows 7 64 bit on a card mother Biostar TA790GX A3 + AM3. I have been running a Phenom II X 2 555 CPU and want to switch to a X 4 965 processor but I can't get Windows 7 to boot when I swap the processors. Both processors are supported by the motherboard and both processors work fine when they work the FRIEND bios routines or control program memory but the motherboard restart when loading Windows 7, usually just after I get my user name and press ENTER.

  The only thing I replaced is the CPU. I tried to reset using the reset ROM bios jumpers, I set the bios to the OPTIMUM setting, and I've tinkered with most of the bios settings, trying to get Windows 7 to go past the login screen.

  This is a security feature to prevent me from moving my copy of system builder OEM of Windows from one computer to another? Is there a work around? I have to call Microsoft? Is there a phone number?

  Well, after having played with a number of commands that have been listed on this website as possible solutions to get a Windows 7 system to start again, I have finally given and decided to do a new install.

  My machine had worked for two years with Windows XP and it had worked for 6 months with Windows 7 32 bit. It worked for 2 months after I upgraded to Windows 7 64 bit. Then I swapped the AMD processor 2 955 X for an AMD X processor 4 965.

  I ran SFC SCANNOW and BOOTREC and I returned my system to the last known good configuration, but I couldn't get my machine to stop crashing to 7 seconds (sometimes 14) after windows login screen appears. After losing a few days I look at Windows 7 boot and planting in an endless loop, I decided to buy a new hard drive and do a fresh install. One of the best solutions is to use MSCONFIG command line program in Win7 to tell Windows to run my CPU upgrade as a processor X 2 or X 3 X 4. This seemed to solve all the problems with Win 7 crash.

  I had a copy of Windows XP for this machine on a hard drive. When I plugged in SATA cables and tried to boot Windows XP with X 4 CPU it initialized right to the top and ran for two days. So, it was not the CPU.

  After a good amount of lost time, I could not have my win7 64 bit system starts so I bought a new hard drive and installed Windows 7 64 bit from scratch. This configuration had no problem for a few days until Windows 7 has started to download UPDATES. It downloaded and installed updates 93 both and rebooted fine. A while later you download 4 updates more. I stopped the machine and started it again and it went into his routine update of files. He said that he applied for 1 of 4 updates. On the second or the third update, he got 32 percent and the judgment. It does three or four times, whenever it came with the F8 boot screen which gives you the opportunity to start with minimum windows. I chose the one with networking. As it starts in this environment, he said that updates had failed and that he would come BACK. HE arrested 3 or 4 times saying it was files back. Finally he started and gave me a login screen. I connected and made a few things, so I closed my computer to see if it would start. He repeats the four files Windows Update reboots, then I went into the minimum windows with networking, he gave me the screen back again, and then he crossed four recovery restart.

  I decided to document the process here in the forum of ANSWERS.

  Now when I pass my cursor on the START > SHUTDOWN button shows Windows 7 wants to "install updates day and then stop" just as he did the last two times. Each series of stops takes about half an hour to go through four cycles of updates and four cycles of returns.

  Now, I'm looking for a way to prevent Windows 7 to try to apply the same 4 updates that have already failed twice.

  I have not mentioned so far, but the 100 MB on my hard drive which is called RESERVE SYSTEM is also a problem, as is PROTECTION on my files. I have a directory on drive E: called IMAGES. He had thousands of photographs that have been put there under Windows 7 in the last years. Now that I can't have that Windows 7 built to start all files have a SECURITY LOCK on them. It is not a problem as a new installation of Windows 7 will allow me to break the lock, as long as I am the administrator. The problem is that I need to break the lock on each directory. Whenever there are a dozen clicks. I'm glad that Windows 7 allows me to break the locks but worth a lock if it can be so easily broken?

  Now, I need to know how to CANCEL these 4 waiting for file updates that will happen automatically when I stopped.

• Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process.

  Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
  Tried running firefox.exe Pei but error message:

  XML parsing error: the undefined entity
  Location: chrome://mozapps/content/profile/profileSelection.xul
  Line 18, column 1:
  "< dialog < =" "^ =" "p =" "> < / dialogue >

  Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.

  Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)

• Error: The installer cannot set Windows XP required configuration information during the upgrade to Windows XP Home SP3 of Windows XP Pro.

  Original title: OEM Windows XP Home SP3 update XP Pro

  Here is a compilation of the messages from another forum regarding
  My problem:
  ---------------------------------------------------------------

  I'm trying to upgrade a Windows XP Home Sp3 OEM system to
  Windows XP Pro. (There are a few Pro features
  that are not available in the House I now need: (1) the files offline and
  (2) an add-on available for free to Onenote 2007, Top2onenote, requires a Pro).
  I don't want a clean install, but an upgrade. I bought a Windows XP Pro
  Upgrade CD on Ebay that was Windows XP Pro
  Gold (v2002). I'm sure that's true for the following reasons:

  It has been listed as an upgrade, but the CD is not labeled "Upgrade".
  It seems very authentic with all Microsoft holography.
  He came in the standard package of Windows XP (without box),
  and it was sealed.
  The name of volume for the CD is WXPFPP_EN. The Internet,.
  It is the retail of Windows XP Pro RTM (gold)!

  Here are things I tried initially.

  (1) I tried to upgrade to Pro from the purchased CD. It is immediately
  has refused to upgrade indicating the upgrade OS (Pro) is older than the
  installed OS (home)...

  (2) I read about "slipstreaming". "Slipstreaming" allows to integrate
  a service pack with an earlier version of the operating system. I created a
  upgrade XP Pro SP3 with Nlite slipstreamed CD image (and
  Autostreamer later, but it made no difference) from the purchased CD
  and a file containing SP3.

  After you burn the CD and start the upgrade
  (Windows installation), the upgrade process
  product through "information collection."
  "Dynamic update" and "Preparation of Installation" with
  no problems. My computer restarted and returned to
  "Installation preparation". A progress bar called 'Progress '.
  quickly filled to about 90% and the hanging system
  at that time there for about 15 minutes.
  Then, I got the following error message:

  Setup cannot set the required Windows XP configuration
  information. This indicates an internal Setup error.

  This is where I am stuck. I had to leave the installation at this point.
  My drive is starts raining and I had to restore a backup.

  (3) just for the heck of it, I formatted my hard drive and
  reinstalled my original OEM XP Home SP3 OS (no clean up, no user file).
  I immediately used my XP CD slipstreamed Pro to try one
  upgrade to XP Pro and IT WORKED! I need to find out why the
  properly clean XP Home OS upgraded to XP Pro but my pre-existing
  (with the files users, drivers, etc..) XP Home OS does not level
  successfully to XP Pro.
  -------------------------------------------------------------

  Another post:

  Yet once, today, I installed a new copy of OEM Windows XP Home Sp3.
  I continue with installation of all the essential and the add-on
  pilots (essentially all my original version). Then, I
  set up a network connection and firewall. With this configuration,.
  I ran the Pro XP slipstreamed SP3 CD. The upgrade to XP Pro
  success (even if the upgrade not configured my graphics
  card properly). I guess my current problem is either the registry,
  the WINDOWS, some user file or parameter file.
  ---------------------------------------------------------------

  Another post:

  I made a file and the backup of the folder C:\Windows folder
  on my system that is pre-existing (OEM XP Home Sp3). I also did a
  separate the backup the State of the 'system' on my pre-existing system.
  These are added my full image backup of her pre-existing
  system a month ago.

  I did a backup image of my system (minimum fees OEM XP Home
  SP3 with all the original installed drivers over a network configured
  connection and a firewall configured). This system will upgrade
  XP Pro with XP Pro SP3 slipstreamed CD successfully.

  Experiment 1:

  I've restored my minimum system. I then restored the C:/Windows folder
  and the State of the pre-existing system backup system. A startup
  has managed (with a minor irritant). I had to activate Windows.
  Then, I tried upgrading the slipstreamed XP Pro processor. He stopped
  at the same place during the upgrade and gave the same error as before:

  Setup cannot set the required configuration information Windows XP.
  This indicates an internal Setup error.

  Experiment 2:

  I've restored my minimum system. I then restored the system state only
  the backup of the pre-existing system. After startup I was asked to
  activate Windows, but answer Yes to the question would be to disconnect me
  the system. I couldn't get connected to try the XP Pro upgrade.

  Experience 3:

  I've restored my minimum system. I then restored only the C:/Windows
  the backup of the pre-existing system folder. Once again, as in experiment 1,
  the upgrade failed at the same place with the same error message.

  ----------------------------------------------------------------

  Before the experiment 3, I hoped that 3 experience would succeed so I
  could conclude that I had a registry problem. I'm not sure now.
  I don't know what to try next. Take the minimum system and reinstalling
  my files of the user is not an option that my hard drive has over 200 GB of
  programs! If I restore all files and folders of my pre-existing
  I would still have backup to restore a system state the reliable (read the registry).
  ---------------------------------------------------------------------

  Sorry for the length! If anyone has any ideas I would appreciate your responses.

  Thank you

  Hello

  This problem can occur if a piece of hardware that is installed on your computer is not compatible with Windows XP.

  For more information, see this link:

  Error message: Setup cannot set the required Windows XP Configuration information

  Hope the helps of information.

• Optiarc bd rom bc - 5500 s work stopped during the upgrade to Windows 7, Windows Vista 64-bit impossible to load the driver.

  Hello

  I use sony vaio VGN-FW290 JTH. I tried to upgrade to Windows 7 and has been invited to uninstall iTunes, Vaio Care, ATI Catalyst Install Manager, ATI Catalyst Control Center, Google Toolbar. I uninstalled it, rebooted the PC and then tried to run Windows 7 installation DVD. Then, I realized that my CD/DVD/BD does not, marked with! in the Device Manager. I tried the procedure in this forum to the http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/957a26d4-4219-4b76-8e89-2e74e6ee2a0e/. I ran SFC tool - it pointed out some problems he couldn't fix it. I tried to update to the latest drivers for the drive, but Windows says that the latest drivers are installed. The properties for the device say: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39):

  I hope someone from Microsoft or Sony can help - I think that it is catch 22 during the upgrade to Windows 7.
  Concerning
  Tomgold

  Hi tomgold,

   

  Welcome to Microsoft Answers Forums.

  This can also occur if an incorrect device driver has been installed for the DVD-ROM device.

  I suggest that you visit the DVD drive manufacturer site download the latest drivers for the drive and install on the computer and if it works. Make sure you download the Windows vista 64-bit driver.

  Device Manager error codes

  http://support.Microsoft.com/servicedesks/webcasts/wc091802/devicemgrerrcodes.htm?gssnb=1

  If the above, step fails I would suggest that you run the patch available in the link below and check if it works.

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• "Windows could not update the configuration to start the computer" error during the upgrade of Vista in Windows XP

  I have a laptop Dell Inspiron 1505, that is running Windows XP Media Center Sp3. I'm doing a place in upgrading to Vista since the disks to upgrade Dell... Everything's fine until the 'Expansion of the files' [27%], then the installation fails with this message: "Windows could not update the configuration to start the computer. Installation cannot continue. Any changes made to your computer during the upgrade". I did a google search for a fix that involves changing a value in the registry in the HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E976-E325-11CE-BFC1-08002BE10318} for example change the value to PartMgr Upperfilters. Unfortunately, this value was the default for my registry key changes could be made. Some other fixes involved the renaming of Upperfilter.bak, for Upperfilters unfortunately this .bak value does not exist in my registry.

  I tried to boot from the disk of Vista and changing the msconfig for a selective startup but without result.

  In addition, the stall even appears at a similar point when you try to upgrade to Windows 7. Is it because of the presence of hidden Media Direct and Dell restore partitions? Compatibility Assistant programs for the two operating systems found nothing significant. Anti virus has been disabled during the installation procedure. Any help will be greatly appreciated. Thank you.

  Hello

  Not quite, but pretty close. Media Direct could not lock the boot sector. It must be a BIOS lock or a mechanism of protection provided by your antivirus software.  Given that, I would check your program settings then for all that prevents changes to the boot sector. You may find more easy just uninstall it and reinstall it after the upgrade. Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Authorization request during the upgrade of the application.

  Hello

  I have the problem with the permission of the application.

  When I install the application, I get the message of trust application, but when I upgrade the application, I don't get the message of trust application but get the message "this application of [application name] has asked an http connection [link URL]" with checkboxes.

  These permission prompts appear 7 times in my application for different URLS.

  Why the permission is changed during the upgrade and how to avoid these prompts for permission?

  What you see is what I see too.  Updates seem to "revoke" the application permissions.

  To work around this problem, I recommend to start the application, that it has the required permissions.  The permissionsApiDemo is a good example of how to do this.  If the application has lost permissions, then you must prompt the user for you give the appropriate permissions - new PermissionsApiDemo is a good example,

  Don't forget that you can actually loose permissions in other ways, for example the user permissions of your application in editing parameters.  If it pays check every time.

• New installation fails during the expansion of the files Windows 7 Pro

  Recently, I built a new computer after my old man died. I installed Windows 7 Pro, I had on the old system. Everything worked well for about a month. Then I started having various errors, some suggesting a memory error. I ran several times using the most comprehensive parameters of memtest and no problem not found. Further inspection, I discovered that a critical system update was applied just before that the problems started. I decided to roll back the change. It does not solve the problem. I tried to do a system repair. That did not work. She only had basic as IE11 and Skype applications. I had also installed the utilities for the motherboard and graphics card. So, I decided to do a clean install. Each time, it fails during the expansion of the files. The error message is, "Windows cannot install required files. The file may be corrupted or missing. Make sure all files required for installation are available, and restart the installation. "Error code: 0 x 80070570." He gets up to 30% each time. I tried to install for a V300 Kingston SSD (120GB). I also tried another SATA II HDD (750 GB) with the same problems. I downloaded a new ISO and tried to install from that. Yet once, it is not at the same point. I noticed that whenever it creates a partition system reserved 100 MB which is almost full. At one point, I got a message saying that there are about 8 000 MB of free space. (I think that was all trying to manually unzip the files by a tip I found online). I found several suggestions for similar problems, but the solutions proposed did not help. I'm sure it will be a simple solution, but I'm out of ideas. Any help would be appreciated.

  Motherboard: MSI MPower Max
  CPU: Intel i7 - 4770 K 3.5 GHz (not overclocked)
  RAM: Crucial Ballistix Sport 16G (2x8G) DDR3 - 1600 MHz
  SSD: Kingston SSDNow V300 Series 120 GB (no special driver needed)
  HARD drive: Seagate 750 G 7200 RPM SATA II
  Video: EVGA GeForce GT 2 640 GB
  Case: Corsair 400R
  Power supply: Corsair TX650M
  CPU cooler: H80i
  DVD: HP, BluRay BD R/W drive
  OS: Windows 7 Professional 64-bit upgrade (the old computer was an XP update)
  CPU Temp is around 42 C.

  If Memtest86 fails then you need to get into the BIOS and set the RAM timing.  Memtest86 + displays the calendar then use the value displayed and compare to the real specs for your memory.  Also, you may need to increase the voltage to the RAM (in BIOS) place a small amount.

  As regards the function of Intel EIST, let her enabled for now. Then enable it after installing Windows successfully.

  =============================================================

  It's the set of test utilities that I use on every new system that I'm building.

  Note: If you are OverClocking or use an automatic overclocking or BIOS power saving features, start by disabling: Intel EIST, Turbo Mode, Cool and pretty and fall back to the speed of stock as a starting point.

  Disconnect any other (additional) internal hard drives and external USB devices.
  Look for any loose hard drive power or cables SATA, graphics card or other power cables.

  First run Memtest86 +:
  It runs from a floppy disk or CD and should eliminate or confirm if one or more of your memory
  sticks are bad or the values of the SPD in the BIOS are correct.
  Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), so no errors at that time then your ram is OK.
  http://www.memtest.org/
  Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
  http://www.overclockers.com/forums/showthread.php?t=409152

  Hard drive test:
  If you do not know your readers of the brand and model, try "Speccy",.
  It provides information from the computer/system in detail:
  OS, CPU, RAM, motherboard, graphics, Hard Drive, optical, Audio, peripherals, network.
  Note: Option RAM indicates number of slots, DRAM Timing.
  Works your memory speed (frequency). The nominal frequency of your memory.
  http://www.Piriform.com/Speccy

  Test your player - create a Bootable CD:
  Ranging from 5 to 25% (depending on the make and model) new hard disks are defective.
  Note: Reliability of HDD sank medium over the past 18 months.

  Test your drive with the car manufacture utility.
  If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools
  (bootable CD) and check bad sectors.
  SeaTools for information: http://www.seagate.com/support/downloads/seatools/
  SeaTools for Windows download: http://www.seagate.com/support/internal-hard-drives/enterprise-hard-drives/saturn/seatools-win-master/
  SeaTools for DOS download:
  http://www.Seagate.com/support/internal-hard-drives/consumer-electronics/LD25-series/SeaTools-DOS-master/

  For Western Digital readers to download the .iso from WdDiag file: http://support.wdc.com/product/download.asp?groupid=611&sid=30&lang=en

  Samsung Estool: http://www.samsung.com/global/business/hdd/support/utilities/ES_Tool.html
  Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm

  Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT
  Diagnostic tool available for use by customers who believe that having a brand Toshiba Fujitsu hard drive:
  http://SDD.Toshiba.com/main.aspx?path=ServicesandSupport/WarrantySupport/SoftwareUtilities

  Notice of suport Fujitsu disk utility: http://www.fujitsu.com/us/services/computing/storage/hdd/

  Toshiba CD bootable: (BACK Diagnostic Tool version 7.0 for IDE/ATA/SATA hard disks)
  http://SDD.Toshiba.com/main.aspx?path=ServicesSupport/FujitsuDrivesUSandCanada/SoftwareUtilities#diagnostic

  ============================ SSD Test Software =============================

  Intel® drive SSD Toolbox
  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=18455

  Life of the SSD: http://ssd-life.com/

  OCZ Toolbox: http://ocz.com/consumer/download/firmware

  SanDisk SSD Toolkit: http://kb.sandisk.com/app/answers/detail/a_id/9328/

  = Once Windows installed =.

  Device drivers: have you installed latest drivers from device of the manufacture of the motherboard?
  Check their support site for the latest drivers as the CD that came with the computer
  or motherboard may be older and less stable drivers.

  Visit the download of the manufacture of the graphics card:
  Download and install the most recent Windows 7 or 8 drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index.aspx?lang=en-us

  See also the test of 'Smoke box' Nvidia or other demos: http://www.nvidia.com/object/cool_stuff.html#/demos
  or equivalent ATI.

  Prime 95:
  http://www.Mersenne.org/freesoft/
  It's a stand alone .exe file contained in an archive .zip.
  Simply choose to run the 'stress test' option for 8 hours or more.
  If your PC can pass this test, your memory and CPU
  are very good (close the housing cover in order to maintain adequate ventilation)

  Core Temp:
  The temperature of each core of the processor.
  Note: For the overclockers using stock radiator and cooling fan Intel/AMD you can expect
  a range of 35 to 40 at idle and 60 to 65 C max temperature when running Prime95.
  http://www.alcpu.com/CoreTemp/

  CPU-ID (CPUZ): http://www.cpuid.com/cpuz.php
  Watch the clock speed of the CPU under various conditions of loading
  (when using speed step technology Intel EIST).
  #1 Note:
  CPU - ID has two tabs - tab 'Memory' that shows the actual speed of the memory
  and the "SPD" tab shows the nominal speeds for each memory location that is filled.
  #2 Note:
  COMPARE the two values, the actual speed of the memory must not exceed the rated speed of your memory.

  CPUID HWMonitor: Hardware program that reads the sensors of health main PC monitoring systems.
  voltages, temperatures, fans speed.
  http://www.CPUID.com/HWMonitor.php

  Test of Stress of FurMark GPU (graphics card):
  http://www.oZone3D.NET/benchmarks/fur/

  Pass marks burn in test: http://www.passmark.com/
  Burnin test, and their test bench at the same time give a good workout from all the major parts of Windows.

  HD Tune:
  Provides information of the car and has an option (tab scan error) to test your drive.
  http://www.hdtune.com/

  CrystalDiskInfo:
  http://CrystalMark.info/software/index-e.html
  User Manual: http://crystalmark.info/software/CrystalDiskInfo/manual-en/
  Monitoring the State of health and the temperature. Solid State Drives brackets (value of the software).

  SpeedFan:
  Monitors internal temperatures and has a function of analysis health online (SMART tab) for hard disks drive.
  It displays your drives model number and compares your drive with other discs of the same brand and model.
  Note: Unfortunately now includes a lot of bloatware, be very careful when installing remove bloatware.
  http://www.almico.com/SpeedFan.php

  GPU - Z:
  A utility light, designed for you give information about your video card and GPU.
  http://www.techpowerup.com/GPUZ/

  PC WIZARD:
  A powerful utility designed especially for detection of hardware, also analyses more.
  He is able to identify a large scale of system components and supports the latest technologies
  and standards.
  http://www.CPUID.com/pcwizard.php

  J W Stuart: http://www.pagestart.com

• Update of the WSF fails during the installation of OLIVIER 11.1.1.9.2 on windows

  Hello

  By updating the WSF using psa.bat when OLIVIER 11.1.1.9.2 on Windows installation I get the following error.

  Downloads have been collected from delivery

  All other steps are completed successfully until ATGLite update, but following the step to update "update of the WSF" fails with the following error. There was no error in one of my previous steps for this installation.

  It is an open question in the forum for the same mistake by an another developed for which there is no resolution.

  ATGLite updated successfully but in error during the upgrade of the WSF installing ODI BIAPPS 11.1.1.9.2

  Please advice.

  [2015-09 - 04T 14: 09:19.272 + 05:30] (Framework) [NOTIFICATION] [update. Framework] addition of dependence on dimension MDS for the invocation BI1 plugin

  [2015-09 - 04T 14: 09:25.711 + 05:30] (Framework) [NOTIFICATION] [update. Framework] user confirms the condition has been met: complete database backup

  [2015-09 - 04T 14: 09:25.711 + 05:30] (Framework) [NOTIFICATION] [update. Framework] user confirms the condition has been met: database version is certified by Oracle Fusion Middleware upgrade

  [2015-09 - 04T 14: 09:55.898 + 05:30] (Framework) [NOTIFICATION] [update. Channel for WSF JDBC connection Db framework]: thin: *.

  [2015-09 - 04T 14: 10:02.746 + 05:30] (Framework) [NOTIFICATION] [update. Channel for WSF JDBC connection Db framework]: thin: *.

  [2015-09 - 04T 14: 10:02.855 + 05:30] (Framework) [NOTIFICATION] [update. Framework] begins to examine the components.

  [2015-09 - 04T 14: 10:02.855 + 05:30] (Framework) [NOTIFICATION] [update. The Framework libraries] for WSF. WSF

  [2015-09 - 04T 14: 10:02.855 + 05:30] (Framework) [NOTIFICATION] [update. C:/Oracle/middleware/Oracle_BI1/jlib/FunctionalSetupManagerLitePlugin.jar frame]

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [INCIDENT_ERROR] [UPGAST-00056] [update. Framework] error of initialization of the plugin update for the WSF. WSF

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [INCIDENT_ERROR] [update. Framework] Cause: a unexecpted error occurred a upgrade plug-in initialization.

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [INCIDENT_ERROR] [update. Framework] Action: contact Oracle Support.  See the secondary error for more details.

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [INCIDENT_ERROR] [update. Framework] []

  java.lang.reflect.InvocationTargetException

  at sun.reflect.NativeConstructorAccessorImpl.newInstance0 (Native Method)

  at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:62)

  at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)

  at java.lang.reflect.Constructor.newInstance(Constructor.java:422)

  at oracle.ias.update.plugin.Plugin.instantiatePlugin(Plugin.java:241)

  to oracle.ias.update.plugin.Plugin. < init > (Plugin.java:222)

  at oracle.ias.update.plugin.Plugin.getPlugin(Plugin.java:156)

  at oracle.ias.update.plan.PlanStep.getPlugin(PlanStep.java:273)

  at oracle.ias.update.plan.PlanStep.examine(PlanStep.java:286)

  at oracle.ias.update.UpgradeDriver.doExamines(UpgradeDriver.java:395)

  at oracle.ias.update.gui.UAExamineThread.run(UAExamineThread.java:44)

  Caused by: java.util.MissingResourceException: can't find oracle.apps.setup.lite.upgrade.plugin.UpgradePluginResourceBundle bundle

  at java.util.logging.Logger.setupResourceInfo(Logger.java:1945)

  to java.util.logging.Logger. < init > (Logger.java:380)

  to java.util.logging.Logger. < init > (Logger.java:374)

  to oracle.ias.update.UpgradeLogger. < init > (UpgradeLogger.java:57)

  at oracle.ias.update.UpgradeLogger.getLogger(UpgradeLogger.java:90)

  at oracle.ias.update.LoggingManager.create(LoggingManager.java:287)

  at oracle.ias.update.plugin.UpgradePlugin.createPluginLogger(UpgradePlugin.java:142)

  to oracle.ias.update.plugin.UpgradePlugin. < init > (UpgradePlugin.java:127)

  to oracle.apps.setup.lite.upgrade.plugin.UpgradeSchemaPlugin. < init > (UpgradeSchemaPlugin.java:57)

  ... 11 more

  ]]

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [ERROR] [UPGAST-00182] [update. Frame] the phase of investigation for WSF plugin. WSF will not run due to a previous error.

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [ERROR] [update. Framework] Cause: an error occurred when loading or initialization of the plug-in which prevents the implementation of the phase requires.

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [ERROR] [update. Framework] Action: review the log file for more details.

  [2015-09 - 04T 14: 10:02.871 + 05:30] (Framework) [NOTIFICATION] [update. Finishing frame] examination of the components.

  • 
    
    

  Hi, it solved finally got with this

  Navigate to the following location and run the command

  \Middleware\Oracle_BI1\biapps\tools\lib

  update the settings in the following command and run it, it works very well

  java-jar biappsrepositoryutil.jar upgradeFSM bi.oracle.home=C:\Oracle\Middleware\Oracle_BI1 work.dir = C:\wkdir biacomp.user = DEV_BIACOMP biacomp.password = db.conn.sid.url = localhost:1521:orcl fsm.db.seed.url=localhost:1521/orcl db.sys.user = sys db.sys.password oracle = *.

• During the upgrade in ARCHIVELOG mode

  Hi all
  
  During the upgrade of the database 10 g and 11 g... I'll put my mode to archivelog noarchivelog mode database to save disk space.
  
  That this task is improving or speedsup improvement process or any impact.
  
  Suggestions please.
  
  Kind regards
  TEJAS

  PL identify accurate versions of "10 g" and "11 g", as well as your OS version

  During updates of database, for most databases, it is recommended to disable archiving because this will speed up the upgrade process. See the exceptions listed by MOS Doc below. Jose has recommended as the upgrade is a case all or nothing - if the upgrade fails for any reason, you need to restore from a backup and start over. Once the upgrade has completed successfully, in archivelog mode must be switched back on again.

  Best practices to minimize downtime during upgrade [ID 455744.1]

  HTH
  Srini

• ORA-04063: package body 'SYS. DBMS_SQLTUNE error' during the upgrade

  Hello
  I am trying to upgrade the oracle 10.2.0.2 on 11.2.0.1 with dbua tool database. During the upgrade "Oracle Server" ORA-04063: package body 'SYS. DBMS_SQLTUNE"error has occurred.
  In the oracle server log:
  
  ---------------------------------------------------------------------------------------------------------------
  
  REM create the automated SQL Tuning task
  REM If the task exists already (catproc is re-of running) is not error.
  Start
  2 sys.dbms_sqltune_internal.i_create_auto_tuning_task;
  exception 3
  so 4 than others then
  5 if (sqlcode =-13607) then - task already exists
  6 null;
  7 other
  8 lift;
  9 end if;
  10 end;
  11.
  Start
  *
  ERROR on line 1:
  ORA-04063: package body 'SYS. DBMS_SQLTUNE"contains errors
  ORA-06508: PL/SQL: called program unit is not found: 'SYS. DBMS_SQLTUNE ".
  ORA-06512: at line 8 level
  
  ------------------------------------------------------------------------------------------------------------------------------------------------------------
  
  After unsuccessful upgrade I have restore and recover the database. SYS. The DBMS_SQLTUNE package and package body were valid. But when I compile them the package becomes invalid.
  I get the error and reach 390221.1 metalink Note:
  
  ------------------------------------------------------------------------------------------------------------------------------------------------------
  
  Solution
  -Drop synonyms
  Drop public synonym existsnode.
  excerpt from Drop public synonym;
  
  ----------------------------------------------------------------------------------------------------------------------------------------------------
  
  But there are no synonyms, which is mentioned in this note in my PB.
  
  How can I solve this problem? Thank you.

  If you have not read the note ORA-04063: package body 'SYS. DBMS_SQLTUNE' errors - upgrade to 10 G and 11 G fails on ID Dbms_sqltune 1271490.1+?

  Nicolas.

• What should I stop time machine during the upgrade at El Captian?

  Do I have to stop the machine in time during the upgrade to El captain?

  N °

  Make sure that your Mac meets the requirements > update of OS X El Capitan

• Why Firefox has disabled the only version of Flash (10.1.53.64) my computer can use? (Mac PowerPC G5) Help!

  Why Firefox has disabled the only version of Flash (10.1.53.64) my computer can use? (Mac PowerPC G5) Help!

  Your computer hardware has arrived at the stage where most of the software needs resources your machine cannot provide because it's too old. You have a few choices.

  1. Get new hardware that can handle the latest software
  2. Use a different operating system, like Linux (which is free)

  I rehabilitated an old G5 recently and it runs very well in the latest Firefox. I put Lubuntu on the machine instead the MacOS. Lubuntu (pronounced Loo-boon-two) is sort of a Ubuntu lite - a user-friendly version of Linux. There are many applications of your choice, and everything is free.

  You can also use the Ubuntu greediest in resources and a little more user-friendly, also free, but you can be more pleased with the performance of Lubuntu instead.

  The PowerPC, I did this on was one of the old blue Bondi ones. Firefox 8 had no problem to start on it at all and has all necessary plug-ins for video, audio, etc... I gave him a church and it works well for them.

  You can download older versions of Firefox, but you'll just open to security problems if you do.

  FYI: The Mac operating system is based on Linux.

• Cannot check iOS 9.3 during the upgrade process. When there is a good connection internet, says no internet. Tried more than 30 times, even after reboot. Any suggestions?

  Cannot check iOS 9.3 during the upgrade process. When there is a good connection internet, says no internet. Tried more than 30 times, even after reboot. Any suggestions?

  You chose the option in iTunes to download the firmware first and install it in a second time after that?

• Qosmio G20 failed during the installation of SP3, now bluescreens on startup!

  Qosmio G20 failed during the installation of SP3, now bluescreens on startup!
  Any suggestions?
  I can't restore to a date prior to the node without danger, he keeps failing?
  Please help me...

  Hello

  Have you tried booting with the CD of Microsoft WXP facilities and try to fix it?
  Sorry, but I don't see any other solution.

  A few months ago, I got a blue screen after installing the new software. I tried to do the same with the safe mode and system restore, but it has not t worked for me.
  At the end I backed up all my important data and installed new WXP.