[Win8] Grayed out Bluetooth switch

Similar Questions

• "Allow a device to plug" is grayed out, bluetooth

  I am unable to connect any device to the laptop via bluetooth, even if I used the service before.

  When I turn on the bluetooth and right-click on bluetooth icon - "authorize a device to plug"is grayed out'.

  I use Windows 7, 64 bit. Any suggestions...?

  HOW PAIR/CONNECT A BLUETOOTH SPEAKER FOR LAPTOP/PC/WINDOWS 7 COMPUTER SOLVED...

  Bought a Bletooth long time speaker, it's good for what it is and managed to get coupled with all my other devices - tablet, phone but have never been able to connect it to my laptop Sony Vaio - always pair then would never be able to connect to it. Here's how I managed to do work...

  I decided to start over and delete all Bluetooth devices and start again.
  Make sure you have your computer Bluetooth on
  Down in the bottom right toolbar right-click on Bluetooth icon
  Click on join a personal area network
  Opens a new window in devices and printers
  Turn on your Bluetooth speaker to find out the mode of
  Click on add a device
  Your speaker should appear
  DO NOT CLICK NEXT...
  AT LA PLACE A MESSAGE SHOULD APPEAR IN THE TOOLBAR SAYING THAT ASKS A DEVICE TO CONNECT
  CLICK ON THIS MESSAGE
  It will then ask you to add a matching number to connect (add the number by default if your speaker has a refer to the manual)
  In this case the XMI X-Mini WE does not come with one so I put in 0000
  Worked!
  Paired
  Now click Start - devices and printers, and you should see the XMI X-Mini US speaker
  Right click and click on the control
  Click on connect...
  Combined BOOM and work
  Don't know how or why his works but I have one now listening to music through my Bluetooth speaker.

  Now I have now, it may not work for everyone, but it was driving me nuts and hope that it works at least for some...

• Grayed out Bluetooth device

  Hello

  my Sony-Ericsson Bluetooth mobile is connected, but grayed out in the
  Devices and printers > Control Panel Bluetooth devices section.
  I use Windows 7.
  When I connect my old Sony Ericsson phone, just before installing the new, everything worked properly;
  I could even use it as a remote control (which is pretty awesome btw).
  Help and all the details for the necessary info are greatly appreciated.
  Ian
  Hello
   
  Method 1:
   

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us
   
  Method 2:
   
  Check out these links.

  Add a Bluetooth device to your computer

  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

  Change settings for a Bluetooth compatible device

  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

  Connect to Bluetooth and other wireless or network devices

  http://Windows.Microsoft.com/en-us/Windows7/connect-to-Bluetooth-and-other-wireless-or-network-devices
   
  Hope the information is useful.

• Bluetooth monitor - power option grayed out

  I just got a laptop Toshiba Satellite A100-163 and trying to set up bluetooth.

  It came with XP Home installed, but I formatted and installed xp professional.

  I had to install drivers manually and got most sorting

  There is always the network left of network controller in the Device Manager I have a feeling is the bluetooth because its nowhere else in Device Manager

  I have problems turning on bluetooth - I installed the bluetooth stack and bluetooth monitor

  Bluetooth monitor is in the taskbar - I right click on it and an option is a wireless link which does not seem to do anything. There is an option to power on and off, but the two are grayed out

  any ideas? I've rebooted etc.

  Thank you

  Hello

  A simple answer: you cannot use the Bluetooth because the Bluetooth device is not available on the Satellite A100-163.

• Android Bluetooth paired with my laptop that Bluetooth was grayed out (NOT the ability to Exchange files)

  Hello

  Connection Bluetooth to an Android mobile with Bluetooth in HP laptop has failed

  I followed these steps to pair the Bluetooth to my HP laptop and the other Bluetooth Android.

  
  First: I clicked on "Add" device "." Second, the Android mobile Bluetooth showed up. Then I connected to it. After that, "Comparing matching Codes" shown to me. (Screenshot below)
  

  Next: The user of each Bluetooth accepted us as confirmation. Finally: The pair has been established well. (Screenshot below):

  

  Although Bluetooth Android was paired with my laptop HP My Bluetooth successfully, the Bluetooth Android is grayed out on my my list of Bluetooth mobile phone as shown in the screenshot below:

  

  Whenever I clicked on the Android Bluetooth listed in my Bluetooth devices, I don't got no control Bluetooth shows me (NO way to send files from Android Bluetooth appears dimmed) also, whenever the user who has the mobile phone android trying to send file in my laptop Bluetooth paired with its Bluetooth Android, it has encountered an error in sending do not file.

  Although the Android Bluetooth is enabled to be detected by other Bluetooth devices.  If there is a problem with my laptop Bluetooth, then I would be facing the same problem with connecting (pairing) my laptop Bluetooth with Nokia Bluetooth.

  Second: A Nokia mobile with the computer HP Bluetooth Bluetooth laptop was successful:

  I followed the same steps to connect Nokia Bluetooth for my laptop Bluetooth, and he was successful.

  

  Then windows checked drivers for Nokia Bluetooth.

  

  

  Then the control of Bluetooth has been illustrated that will allow to me and the other a user send and receive files via Bluetooth pairing:

  

  NOTE THE DIFFERENCE BETWEEN a connection NOKIA BLUETOOTH WITH MY BLUETOOTH, AND ANDROID BLUETOOTH WITH MY COMPUTER PORTABLE BLUETOOTH LAPOTP):

  1. There is no verification windows drivers for the moment got sync to my laptop Bluetooth Bluetooth Android. However, there is a windows drivers for Nokia Bluetooth control when it is obtained associated with my laptop Bluetooth.

  

  2 - THE NOKIA IS NOT CLOTHING OUT(active/enabled), HOWEVER, THE ANDROID IS GRAYED OUT (inactive/disabled)

  

  I hope you understand the answer for me and me.

  Hello

  I suggest you post your query on the HP forums to get information on the numbers of care for the HP customer for your location because we have no details for him.

  HP Support Forums

  http://h30434.www3.HP.com/

  I hope this helps.

• Options grayed out after that migration vSwitch0 vmk0 to distributed network switch

  I have a bunch of ESXi 6 guests, where I would like the default vSwitch0 to a vDS management interface. However, it seems that the management network gets screwed more or less of this operation

  First I tried to simply migrate the physical interface and vmkernel to vds = no chance (resets the form configuration time to hosts)

  Then I tried to connect a NIC seconday to the same switch, adding as a management console interface, make two interfaces marked as management interfaces. The uplink of vSwitch0 is replaced by the new interface and the vds is mapped to the original management interface. From this point, I can migrate vmk0 to the distributed switch and remove the extra card. All good, at least at first glance. The army continues to communicate with vCenter and so on. However, return to the console options to "Network adapters" and "VLANS (optional)" are grayed out. The only way I managed to get back them is again a reset to the default settings of the management network.

  After som test front and rear, it seems that these options disappear as soon as vm0 leaves vSwitch0?

  Any ideas how to solve this problem?

  The army continues to communicate with vCenter and so on. However, back to the console options for "Network adapters" and "VLANS (optional)" are grayed out. The only way I managed to get back them is again a reset to the default settings of the management network.

  I guess that's the expected behavior, because once your vmk0 has been migrated to vDS, now the vDS control plan which is with vCenter server will allow you to change these settings as network card and VLAN ID etc.

• < Display Caller ID > disabled and grayed out.

  The title says more or less. I found yesterday from my wife that when I call him my number comes as "unknown". I know where the preference "Show Caller ID" is, but it is grayed out as non-functional. It is set to 'stop' and will not be can depend on.

  The phone is updated with iOS 9.3.2 and the update has been applied to several weeks (4-8) before this problem arose. I don't know things that occur out of no where, but that's how it seems. I restarted the phone and also reset network settings, but none has made a difference.

  Just days before that, I discovered late one day that all my calls for the day have been "missed". I knew that something was wrong here. Started with AT & T and it turns out that I threw a good sting. AT & T had recently made an update to the system and it had somehow me switched to a phone restricted, could make calls but not receive calls. A few minutes later everything was fine - thought. Today, they assure me that the problem today is not theirs and I should call Apple. Long call with Apple broke and I had to get a call, it never came.

  Don't know what else to say here. Any ideas/help appreciated.

  IMO no matter what AT & T told you, it seems that the fault is theirs. You can just try it with a different sim card and you will have the answer. Also, try to connect your phone to iTunes and "check for updates". This function also checks the parameters of your career, so if there is an update, you will get it.

• Satellite Z930 - mode boot Boot CSM and grayed out on the value

  Hello

  Hope someone can help me please.

  I have a Toshiba Ultra Z930 friends book.

  When you start the laptop does not start it comes up with the meesage PXE - E61: Media Test Failure.

  It is a Windows 8 portable 3rd Gen i7.

  I can boot from Hiren'S and the hard drive is located and can be selected and all files seem to be intact.

  I went into the BIOS and found that the startup mode is set to MSC Mode.
  However, Windows 8 requires the for UEFI boot mode.

  I can't find how to change the boot of the CSM Mode in the UEFI.
  The option is grayed out and cannot be selected.

  Help
  Please

  Hello

  Go to the BIOS by pressing F2.
  Then put the BIOS on the default settings, save the changes and power the laptop off.
  Then switch on the device and access to the BIOS, once more the key F2.

  According to my experience, secure boot option must be available, and you should be able to change the startup mode UEFI/CSM layout too.

• Pavilion p6506f: System Recovery option grayed out when you use the recovery to factory default reset disk

  Dear experts,

  Please help me on what I am making a solution for about 4 hours now...

  Somehow my recovery partition is damaged, so I use the recovery disk that I created when I bought the computer.

  I used the disc to start the computer and after loading files and everything on the menu of Recovery Manager "System Recovery" is grayed out.  Note that I have not changed any hardware on the computer.

  Help, please!

  Thank you!

  Hello

  You did do the right thing. But you created a Win 7 recovery disk, not the game of HP recovery disks.

  You can switch to Win own 10.

  You will need the product key Microsoft of the COA sticker attached to the frame of your PC of 25 characters.

  Images of example COSTS:

  

  Do a clean install of win 10 If you do not know the product key of Windows 7 on the certificate of authenticity.

  Win 7 PC sometimes have problems updating to Win 10.

  I really think you should get support from HP Win 7 recovery. If the Win 10 upgrade fails you can always return Win 7 If you have a Win 7 HP recovery media.

  Your choice.

  Jay

• Qosmio X 870/016: win 8.1 - 3D DVD player option grayed out

  I have a Qosmio PSPLZA-016003 with Win 8.1
  What news I couldn't play 3D 3D Blu - ray discs no problem on Win 8
  I've updated to Win 8.1 but did not check the 3D DVD worked.

  After that Toshiba Service Update Blu - ray player, I couldn't play the 3D 3D discs - they appeared as 2D with 3D icon grayed out. The update of the Blu - ray player service was at 1.0.5.175

  I have:
  1 update of BIOS to 6.3 on the support site.
  2 player deleted and reinstalled from my c: drive
  ... program files, PINES, COMPS1, Toshiba blu - ray Disc Player - V1.0.5.48
  3 installed V1.0.5.175_A on the support site (this indicates in "Any player" V1.0.5.175)

  I still have the problem DVD 3D showing as icon 2D and 3D shaded in the player window.

  I guess the combination of Win8.1, 6.3 Bios and DVD Player V1.0.5.175_A should work - any suggestions?

  Hello

  I guess you did something wrong during the update to win 8 to 8.1 Win

  On this page of Toshiba (responsible for the Australian series laptop) here is information how to change units to win 8 to 8.1 Win
  http://support.Toshiba-tie.co.jp/windows81/upgrade_au.htm

  On this page you will find the Driver and Application updates, the Limitation and notifications, and additional information in case you want to do a clean install of 8.1 to win:
  http://support.Toshiba-tie.co.jp/windows81/update_au.htm

  On this page you will find the drivers Win 8.1 and tools for Qosmio X 870 (PSPLZ *) series
  http://support.Toshiba-tie.co.jp/windows81/drivers/PSPLZ_Up_au.htm

  You can find the TOSHIBA Blu - ray Disc Player V1.0.5.175 to Win 8.1 and other drivers

• I can't get the tabs of the previous session of the return when I reopen it Firefox. The header of the window, or 'Quit' in the file Menu using 'Close' of Firefox not working. Note that "Restoration of previous Session" on my Menu history is grayed out so

  Question
  I can't get the tabs of the previous session of the return when I reopen it Firefox. I tried closing with 'Close' header of Firefox window, but also 'Quit' in the file Menu. Note that "Restoration of previous Session" on my Menu history is grayed out so I can't use it. In addition, there is no tab at the top of my window to open Firefox Firefox - only a menu bar that shows "File", "Edit", "View", "History", "Favorites", "Tools" and "Help". I am running Windows 7 Home Professional and Firefox 4.01

  "I can't do the tabs from the previous session of the return when I reopen it Firefox.

  Remember that you are not private browsing or they are in permanent private browsing mode. See: https://support.mozilla.com/en-US/kb/Private%20Browsing (2nd and 3rd options menu on this page)

  Make sure that you are not clearing history during a session or when Firefox is closed. See:

  • Clear recent history: https://support.mozilla.com/en-US/kb/Clear%20Recent%20History
  • Clear history of Firefox closing: uncheck 'Clear history of Firefox closing' options > Privacy panel (the first item under "History" on this Panel should be set on "Firefox will be: use the custom settings for history" to see that point to uncheck)

  "There is no Firefox tab at the top of my Firefox window open - only a menu bar.

  The Firefox button is supposed to be on by default in Vista and Windows 7.

  In Firefox 4, you have the choice of using the Firefox (orange or grey) button in the upper left or the menu bar (File, Edit, View, history, Favorites, tools.) Help).

  • The selections on the Firefox button are distinguished by the menu bar options.
  • You can easily switch between the Menu bar and the Firefox button or leave one or the other active.
  • One used depends on if the Menu bar is enabled
    • Bar menu checked = Bar Menu on, Firefox off button
    • Bar menu unchecked = Menu Bar off, Firefox button on

  When the Firefox button appears and you want to temporarily view and use the menu bar, press ALT or F10 displays the menu bar and you can make your selections in the Menu bar displayed temporarily.

  To check (or uncheck) the menu bar, do one of the following:

  • using the Firefox button: click on the Firefox button > Options > Menu bar
  • using the Menu bar: click on view > toolbars > Menu bar
  • Hold DOWN the ALT key while pressing the VTM keyboard letters

• Most of the pieces in my albums and playlists is grayed out and will not play.

  When I go to play the songs in iTunes a lot of my songs (mastered and uploaded) are grayed out and I can't play. For example, when I press shuffle play only items not greyed out. Sometimes, the album is grayed out and will not play. This has never been a problem until recently. I used to love iTunes, now with each update, it seems more confused. Help please. Thank you. Rock ' Roll!

  Switch to the view of songs. The greyed out, you saw previously correspond to unchecked items? If for Cmd-click any empty box must all check.

  TT2

• 3110em: HP recovery partition exists, but the recovery of the system in the grayed out Recovery Manager?

  I have a hp recovery partition on my laptop, and I want to recover my PC.

  I go into the Recovery Manager, windows system restore is available, but the HP system recovery is grayed out and unavailable.

  I don't know what to do, is partition recovery for windows 7, but since I upgraded to Win8.1, I had a lot of problems, and I want to go back.

  Please help me if you can.

  The system recovery option means that it seems to be corruption or another problem with the score of recoveryt.

  As is the case, then you would use the recovery (USB or a game disc) media, you have already created to perform the recovery.

  If you have not created a recovery media, you will need to order a recovery USB stick (preferably) or a record of recovering HP or HP partner. The cost is usually about $30,00 USD

  Order a HP recovery disk

• SRW2008P - Advanced QoS Mode is grayed out

  Hello

  QoS-section of the web interface SRW2008P I can choose between Disable and basic, advanced mode is grayed out.

  I created a new ACL but advanced QoS mode is not available.

  What can I do to activate it?

  -----------------------------------------

  Start the Version: 1.0.1

  Software version: 1.0.4

  Hardware Version: 00.03.00

  ------------------------------------------

  Any help much appreciated, thanks in advance!

  Hi, I also had this problem with the advanced QoS mode is grayed out in the web interface. A firmware update, many factory reset without success, very frustrating and disappointing as I too bought this switch for its QoS functionality. However...

  1 console Telnet to the switch, log in using your user/pass

  2. Ctrl-z to exit from the menu, you will get a > prompt

  3. type lcli - you will be asked once again in your credentials, it takes you in a familiar Cisco IOS-like CLI

  4. type conf - enters configuration mode

  5. type advanced qos - you will be asked to confirm it clears basic QoS settings.

  You can now create your class cards and set policies to interfaces.

  In fact, using the light CLI rather than the web interface to configure.

• Button grayed out ordering?

  Does anyone know what would cause the button to place an order to be grayed out? I see the end button in the final stage of Fund but his gray. No error showing. Only recent change was connected to the switch from USD to EUR currency and now I can not place the order? New here, any help is greatly appreciated.

  Hello

  You must have a ship to address and the invoice to the full address, a selected payment type, a full delivery mode, and

  If you have terms of Conditions &, they must agree to so that the Place Order buttons to be available.

  Confirm the value of the IBE profile option: enforce the terms and Conditions by user review

  B2B (business) user must have a role with IBE_CREATE_ORDER permission to display the button to place an order.

  Kind regards

  Debbie