Windows 10/ESXi 6.0 NIC ad nauseam resets
I am running Windows 10 on ESXi 6.0.0 build 2494585. I was running into the problem that others have experienced where windows will shut down in ~ 24 hours. I came here on these forums and learned that it was thanks to the SATA cdrom drive. Thanks for this tip.
In the next issue, I have found now that my computer can stay long enough for a new problem to occur:
I thought that I was running on this problem even once when I went to RDP on my computer and it was not available. I opened vSphere and of course, the machine is running, but the State of the network said no connectivity. I have to disable and re-enable the network interface to find the connection. I have pasted below information from system logs. This message is repeated hundreds of times, incrementing the newspaper each time. Does anyone have an idea what I can do to work around this problem? It happened at least 3 times now. I found a similar problem on another forum with a person running Windows 10 on Parallels, but the County was nowhere near as high. I have followed the advice on this thread and disabled IPv6 when even in the case where.
Event 10400
Network interface "Intel (r) PRO/1000 MT Network Connection" started resetting. There will be a momentary in network connectivity interruption, while hardware resets.
Reason: The network driver asked that it resets itself.
This network interface reset 784 times since it has been initialized last.
-System
-Supplier
[Name] Microsoft-Windows-NDIS
[Guid] {CDEAD503-17F5-4A3E-B7AE-DF8CC2902EB9}
EventID 10400
Version 0
Level 3
Task 0
Opcode 0
Keywords 0x2000000000000000
-TimeCreated
[SystemTime] 2015-09 - 15 T 04: 43:00.030527700Z
EventRecordID 33966
-Correlation
[ActivityID] {B24FC05A-C7D0-4A32-B408-F6B497C97193}
-Execution
[ProcessID] 4
[ThreadID] 8308
Channel system
Computer RWDW10
Security
-EventData
IfGuid {B24FC05A-C7D0-4A32-B408-F6B497C97193}
IfIndex 6
IfLuid 1688849960927232
AdapterName Intel(r) PRO/1000 MT Network Connection
ResetReason 2
ResetCount 784
NIC that is attached to the guest operating system: you can try with vmxnet3.
Tags: VMware
Similar Questions
-
P2V Windows 2000 ESXi 5.5 conversion
Hello
We lack ESXi, vCenter 5.5 with 3 5.5 hosts. I am trying to convert an old Windows 2000 Server physical and add it to one of our ESXi hosts.
It seems that the latest version of the Agent converter that I can run on the W2K Server is 4.01. Something more recent than that will not install.
And version 4.01 of the stand-alone converter cannot connect to a host ESXi 5.5, (because it is not not compatible I suspect).
If I run 5.5 Converter Standalone and connect you to the W2K Server, he wants to upgrade the agent which, of course, he can't.
Anyone have this working?
Do I have other options?
Thank you.
For anyone else who may find themselves in this position.
I used to convert physical server Win2K Server VMware vCenter Converter Standalone 4.01 virtual 2.x.
When it's done, I used vCenter Standalone Converter 5.5.3 to convert the image to Vmware Server 2 5.5 ESXi infrastructure.
I went all start the server ESXi without a NIC attached and all seems OK, so confident when I do for real, it should work.
-
I have been sign out of windows xp man and do not have the reset disk (forgot password)
I was disconnect from windows xp man and do not have the reset disk (I forgot the password) I try usign the Ctrl, Alt, delete twies and does not work then what I can do someone can help me. Thak you Gracias
Keep passwords secure - Microsoft on passwords strategy
http://support.Microsoft.com/kb/189126What to do if you forget your Windows password:
http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-you-forget-your-Windows-password -
Dell R710 and ESXi 4.1 NIC issue.
Please bare with me, I'm a newbe with vMware.
My question is this:
Got a new Dell R710 with Broadcom BCM5709 quad. Install ESXi 4.1 CD. Then, I created a virtual machine and install Win Server 2008 R2 64 bit.
In vSphere Client under configuration-> network-> properties (per virtual switch)-> network-> adapter details maps I see the Broadcom adapter. But in Windows in the Device Manager the NIC comes as Intel PRO/1000MT.
This is the expected behavior? ESXi support a pilot intel virtual any? or must we show Broadcom NIC.
If this is not the expected behavior, please suggest a solution.
Thank you
Welcome to the community,
what you see is expected and in design. ESX mask the real hardware and presents a virtual hardware to virtual machines. In this way, you are able to move the virtual machine across different hosts and even VMware Workstation, player,... without a lot of changes.
André
-
Windows 2008 server and second nic
Hello
I added a second NIC on a server win2008r2. The NETWORK adapter has been configured for a different use for dedicated backups segment. I see traffic, send and receive. Public/not identified said interface. I found articles to change privately and did so with no luck. I have disabled the firewall for profile modeling with no luck. Any help would be appreciated. Thank you
Post in the Windows Server Forums:
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/ -
I have two hosts (vhost1 = ESX 4.0, vhost2 = 5.5 ESX) both are configured for the Group and both connected to a switch of 1544 Adtran L3 (named sw01). vhost1 has been in production for several years with the config below and has been solid as a rock. I'm trying to reproduce the installation of grouping/collage on vhost2 and it does not work when are associated but will work when you are using a single NIC (with or without aggregation).
To be more specific about what does not work, two virtual servers have "Network server" (vlan 8) defined as a group of ports. Both physical and virtual servers on the same vlan cannot ping or resolve queries arp for virtual machines on vhost2. Everything that is sent from a different subnet can connect to the virtual machines on each virtual server.
So the question is this: why not ESX 5.5 works as ESX 4.0 when the configs are also near identical, as I can make them and they are connected to the same switch?
Thanks for any input you can provide!
S
This is the configuration for vhost1
switch 1 (sw01)
SW01 #sho run int port 3
Building configuration...
!
!
interface port-channel 3
Description LAG for vhost1
no downtime
switchport mode trunk
switchport trunk allowed vlan 1.8
!
end
SW01 #sho run int 0/23 concert
Building configuration...
!
!
0/23 gigabit-switchport interface
Vhost1 vmnic2 vswitch1 description
no downtime
channel-group mode 3 on
!
end
SW01 #sho run int concert 0/24
Building configuration...
!
!
0/24 gigabit-switchport interface
Vhost1 vmnic1 vswitch1 description
no downtime
channel-group mode 3 on
!
end
vhost1
[root@vhost1 ~] # esxcfg - NICS - l
Name PCI Driver link speed Duplex MAC address MTU Description
vmnic0 03:04.00 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f4 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter
vmnic1 03:04.01 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f5 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter
[root@vhost1 ~] # esxcfg - vmknic - l
Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type
vmk1 VMkernel - Server NetIPv4 10.1.8.31 255.255.255.0 10.1.8.255 00:50:56:78:9e:7e 1500 65535 true STATIC
VMkernel - SAN Net IPv4 10.1.252.20 vmk0 255.255.255.0 10.1.252.255 00:50:56:7 c: d8:7e 9000 65535 true STATIC
[root@vhost1 ~] # esxcfg - vswif - l
Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE
Service vswif1 - NetIPv4 management 10.1.1.12 console 255.255.255.0 10.1.1.255 true STATIC
[root@vhost1 ~] # esxcfg - vswitch - lSwitch name Num used Ports configured Ports MTU rising ports
32 4 32 1500 vSwitch0
Name PortGroup VLAN ID used rising Ports
0 3 VM network
Switch name Num used Ports configured Ports MTU rising ports
vSwitch1 64 12 64 1500 vmnic1, vmnic0
Name PortGroup VLAN ID used rising Ports
Server network 8 7 vmnic1, vmnic0
Console - management service vmnic1 Net0 1, vmnic0
VMkernel - server 1 vmnic1 Net8, vmnic0
On the Load Balancing vSwitch it Hash IP value.
This is the configuration for vhost2
switch 1
SW01 #sho run int 4 port
Building configuration...
!
!
interface port-channel 4
LAG description for vhost2
no downtime
switchport mode trunk
switchport trunk allowed vlan 1.8
!
end
SW01 #sho run int concert 0/17
Building configuration...
!
!
0/17 gigabit-switchport interface
Description vhost2
no downtime
channel-group mode 4 on
!
end
SW01 #sho run int concert 0/18
Building configuration...
!
!
interface gigabit-switchport 0/18
Description vhost2
no downtime
channel-group mode 4 on
!
end
vhost2
~ # esxcfg - NICS - l
Name PCI Driver link speed Duplex MAC address MTU Description
vmnic0 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 0000:08:00.00 1500 c Intel Corporation 82574 L Gigabit Network Connection
vmnic1 0000:09:00.00 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 d 1500 Intel Corporation 82574 L Gigabit Network Connection
~ # esxcfg - vmknic - l
Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type
Management 10.1.1.15 IPv4 network vmk0 255.255.255.0 10.1.1.255 c 1500 65535 real STATIC 00:25:90:e7:0e:9
~ # esxcfg - road - l
VMkernel itineraries:
Interface of network gateway subnet mask
10.1.1.0 255.255.255.0 subnet local vmk0
by default 0.0.0.0 10.1.1.1 vmk0
~ # esxcfg - road - n
Expiration type neighbor Interface MAC address
10.1.1.1 00:a0:c8:8 has: ff: 3 b vmk0 19m13s unknown
~ # esxcfg - vswitch - l
Switch name Num used Ports configured Ports MTU rising ports
vSwitch0 4352 7 128 1500 vmnic0, vmnic1
Name PortGroup VLAN ID used rising Ports
Server network 8 1 vmnic0, vmnic1
Management network 0 1 vmnic0, vmnic1
On the Load Balancing vSwitch it Hash IP value.
Hello
Do you share the vmnic for ESXi management and network of the VM?
Try to follow the steps in this KB: VMware KB: NICs using EtherChannel grouping allows intermittent network connectivity in ESXi
Trying to team adapters using EtherChannel, network connectivity is disrupted on an ESXi host. This problem occurs because grouping NIC properties will not propagate to the network management portgroup in ESXi.
When you configure the ESXi host for grouping of NETWORK cards in attributing to the road based on ip hashload balancing, this configuration is not propagated to the portgroup management network.
Workaround
Note: to reduce the possibility network loss please change the route based on the hash of IP using this method of balancing load vSwitch
- Close all ports in the physical switch team leaving a single port as active.
- Change the Route based on ip hash vSwitch and load balancing management Portgroup.
- Set up the physical switch port channel.
- Activate the physical switch ports.
Notes: Using this method will avoid a loss of connection when you switch to a port channel. Also make sure that under the properties for vmk portgroup # used for network management you tick the box "Enabled".
-
Customization of Windows on ESXi 5.1 with a failure of vCenter 5.5
Hello!
We have a problem with o/s (2008 R2 SP1) of Windows customization on our 5.1 ESXi update 3 (build 1743533) hosts
given that we have updated the server vCenter Server since 5.1.0 in the last 5.5 Update 1 version.
The sysprep command works normally and personalization seems to be good at the end of the day,
but we do not get "successful personalization" more in the events of the virtual computer.
This is the end of the file "C:\Windows\TEMP\vmware-imc\guestcust.log":
[2014 06-09 T 12: 43:50 INFO] Called GuestCustUtil .
[2014 06-09 T 12: 43:50 INFO] Params: flagComplete
[2014 06-09 T 12: 43:50 DEBUG] Current customization, the value 0 to 2014-Jun-09 12:43:50
[2014 06-09 T 12: 43:50 DEBUG] RPCI: Send request = 'deployPkg.update.state 5 C:\Windows\TEMP\vmware-imc\guestcust.log 0'
[2014 06-09 T 12: 43:50 DEBUG] RPCI: Envoy = 'deployPkg.update.state 5 C:\Windows\TEMP\vmware-imc\guestcust.log 0' request, response is "unknown command", len = 15, status = 0
[2014 06-09 T 12: 43:50 ERROR] Cannot create the personalization in vmx State.
[2014 06-09 T 12: 43:50 DEBUG] SysprepDecrypter has the password successfully unobfuscated
[2014 06-09 T
This is the only mistake we have in all the newspapers (C:\Windows\System32\sysprep\Panther\setupact.log is 100% success)
and it seems that it is just the end "GuestCustUtil flagComplete" which does not work.
Wouldn't be a compatibility problem with the GuestCustUtil of vCenter command 5.5 (as dated 16/04/2014) with our 3 ESXi 5.1 update hosts?
Thanks in advance for any ideas.
We have an open for this issue support ticket.
There is a work around in this article: http://kb.vmware.com/kb/2078352
-
Windows Server 2012 R2 4 NIC team LACP
Good day to all
I configured a LACP 4 niic bundle on my Server R2 of 2012, all network cards are the same. I set up my 4-port CISCO 6509 as follows
Interface Port-channel50
Description * link to Backup Server *.
switchport
switchport access vlan 130
switchport mode access
endAll 4 ports are configured in the same way as shown below
!
interface GigabitEthernet1/2/27, 03/01/27, 02/02/29, 03/02/29
Description * BackUp Server 1 *.
switchport
switchport access vlan 130
switchport mode access
spanning tree portfast edge
passive mode of channel-group 50
endI have all 4 cards in a single team LACP with hash address as mode. When I plug in cards NETWORK 3 and 4, the machine works as it is on an old earthling in modem 36 600 dial and says "Media disconnected" with the "link"light, but the activity of flashing light. " If I turn off then re-enalbe the NIC led "link" is that they work until I restart. However 4 NIC always gives me
"Blame LACP negotiation."
Any ideas on why this is happening, especially the restart and they never seem to initialize, at that time, I have 3 were team together and it seems to work properly, of course, until I restart.
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
ESXi 5.5 NIC not detected
I have an ASUS M4N68T-M V2 with built in network card, while I'm installing eSXI 5.5, I get an error of not detected NETWORK card. an advise please. Thanks in advance :-)
I can't tell you if the NETWORK card works with older versions of ESXi as he is not on the list of supported network cards. You can try if.
Anyway, other users on the forum succeeded with an adapter Intel Pro/1000 GT desktop, you may be able to get at a lower cost. From what I have found, your motherboard has two PCI slots, so it could be something to consider.
André
-
I want to install WindowsServer 2012 and after gpoing through the configuration it is just a windows black screen with the spinning circle counter. Everyone see it and have a fix.
Look at the KB 2021887
You should also look at
-
VMDK file between windows and ESXi with VMFS on iSCSI copy
Hi all! I searched here and that you find that no good answer but then I hope that someone can help you.
We have a group of 3 servers ESXi running off a single iSCSI target and often need to copy VM from the VMFS file system.
To help the conversion tool is incredibly slow, it's on. WinSCP and FastSCP work at about 5 MB and 3 MB/sec. FTP is the best option so far, but it is only 8 MB/sec. When we have to copy around a virtual machine that takes a lot of time of 20 GB. In addition, when we make 15 copies of a VM is incredibly long.
I hoped to be able to directly connect to the iSCSI target and mount the system files somehow, but can't seem to find a way to do it. Defect is there any method better or faster? Perhaps a better FTP server than the option of proftpd?
We hoped a local copy with either USB or eSATA method, but doesn't seem to work. USB is not detected even and I can not get a non-VMFS file system to mount via eSATA.
If it works better we can set up a linux machine to mount iSCSI target if copies of file can work this way.
Thanks for the tips!
NFS?
-
I have a HP proliant running ESXi 4
The vnet0 is set to static IP address
It is connected to a firewall
The vnet1 is connected to the same firewall and there is a DHCP server provides IP addresses of
10.10.10.10 for 10.10.10.250
A virtual server connected to the (default) vswitch0 works fine, but the second server connected to the another vswitch using the second network card
is having a few problems.
I tested on a different network, as a test environment, now I need for this production and that causes a problem.
Can someone give me an idea on what may be wrong with this configuration?
Thank you
Xavier
Welcome to the VMware forums communities. Is both connected to the same switch, HP network adapters or you have a LAN / DMZ or similar split? Virtual machines on the 2nd vSwitch have a problem in obtaining an IP address? What is the nature of the problem having these virtual machines?
-
ESX 3.5 - Guest OS Windows 2008 R2 x 64 NIC Drivers
I installed 2008 R2 x 64 as a guest operating system on ESX 3.5. The NETWORK adapter is displayed but no driver and install vmware tools has nothing. Where can I get the x 64 drivers for 2008 R2 x 64? The esx perhaps U1 or U2.
Thank you.
Hi COS.
2008 R2 is not supported before the update 5. You can try to configure the virtual NIC to e1000 and install new VMware tools.
Good luck.
Concerning
Franck
-
'Check' updates from Windows Update is stuck after that I have reset my laptop
I refreshed and reset my laptop but it will always get stuck 'Check updates' and everything works so slow... than ever before.
Is this a problem with my hard drive?Sorry, but your reset laptop reset Windows Update.
I recently had to do this in one of my PC and it took three days complete (!) for the Windows Update process finish. One day find updates, one day to download and one day to apply.
To add to the frustration, during downloads, progress 'freeze' to zero percent!
So, I had it got stuck - but she didn't - and this is important! Go to C:\Windows\Distribution. If there are files and folders, Windows Update works, it is simply not updated status information.
You can check that from time to time, and while its download yet, he will continue to grow. As long as there are files and folders there DO NOT shut down your PC! This will force again when you reboot.
Sorry... but you just have to leave it on and it will run its course.
Good luck
I'm a volunteer and I do not work for, or represent, HP.
========================================================================
If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.
-
I don't remember my password for mail electronic windows and can not find a way to reset
Icannot remember the password for windows mail the remember me box became disabled and I can't find a way to reset
Hello
I suggest you go to the following Microsoft article and check if it helps.
Microsoft's strategy concerning lost or forgotten passwords: http://support.microsoft.com/kb/189126Hope the information is useful.
Maybe you are looking for
-
How can I show only music actually present on the iphone?
I recently had to reformat completely in iPhone 6s. Now, the 'Music' application shows all the music on my laptop iTunes library: I just want to see music actually physically present on the iPhone. I don't want to see I have to listen to or download
-
Installation upgrade value package
Belatedly, for various reasons (mainly the uncertainty and concern that I would mess up the computer at an inopportune time), I have round for a second attempt to install the published Package value update January 9, 2008 (with various other latest d
-
Touch screen suddenly not working
I have the HP Split 13 2 removable PC with Windows 8.1 x and when I got it the touch screen worked fine with or without be switched to the keyboard. A few days ago, I noticed that the touchscreen became completely unresponsive. I have not checked thr
-
Hello I'm using LabView 8.6 Standard. Could someone please direct me to the appropriate examples please or advise me on a solution. The problem. I have an image varying in shades of color that has been transformed into a sorta like a heat scan summar
-
ADJUST THE SIZE OF THE SCREEN LOOKS A
Currently, my display screen is not in line with the size of the computer screen. There is an inch of black on each side of the display area. Using the browser to stretch the screen does not work. Ralph