Windows 7 installation / drivers required

Similar Questions

• Windows 7 installs drivers / print Oki 431dn printer

  Hello MS community.

  I've upgraded a Windows XP computer to Windows 7 to upgrade to windows Vista then 7. then I put the hard drive in a newer computer (in order to have an improved machine) and made a windows repair if it works properly. everything works in their computer, except that I can't get the Oki 431DN printer working. is it possible that the pilots are now corrupt? already, I went in management of printing and removed the printer and its driver besides files. You can provide any help would be great!

  Unless you had a commercial full version of win7 when you put the HD in a new PC and repaired, it may fall at any given time.

  On the support site of Oki that there could be a utility to remove it completely if so use it, restart the PC reinstall Oki drivers

  http://www.Oki.co.UK/support/printer/printer-drivers/results.aspx?ProdID=TCM:122 - 107774 & search = 1 & DiSo = Windows 207% 20 x 64 & languageId = ENGLISH & type = | drivers

• New Windows XP installation disc required?

  I have a plu Sony notebook comes with pre-installed XP Pro and I would perform a clean reinstall of the operating system. Restore disks from the system that comes with it (no Windows disk was provided) force the partition from the C: drive to a maximum of 15G (for some reason any) with the rest of the HD (60G total) space assigned to a logical drive D:. In addition, the recovery process reinstalls the original beam of s/w that is now mostly obsolete and unnecessary. That leaves very little space on the C drive for additional applications and many of the old Sony uninstall apps causes system instability.

  If I could just re - install Windows XP on a single partition without all other garbage, I'm back in business. But, I can't seem to find a way to get a new copy and license of Windows XP (there are a lot of fakes out there, but I'm not interested).

  The computer does not have a sufficient memory for Windows 7 and I have a few important apps that does not work under Vista, so what, if any, options are available to me?

  Any advice would be appreciated.

  If your computer has an i386 folder, then you might be able to try this procedure.

  http://www.howtohaven.com/system/createwindowssetupdisk.shtml

  I did it with XP home SP2 disc.  It is installed with success twice on the same computer.

• Error message from Windows XP Pro SP3 1720 Windows installation Script required

  Original title: WINDOWS XP PROFESSIONAL VERSION 2002 SERVICE PACK 3-__ERROR MESSAGE 1720 FOR WINDOWS - installation SCRIPT REQUIRED FOR INSTALL NOT running.

  I get error message 1720 whenever I try to install an Internet card mobile broadband (MC760) at Virgin Mobile

  Hello Ivpg1963,

  I saw a suggestion in another forum that said to remove drivers Virgin Mobile via Add/Remove programs.
  Then, remove the Novatel directory in Program Files. They claimed that remove the directory was the key.

  Then add the drivers of Windows XP to return to the large map Strip MC760.

  Please reply back and let us know if this can help.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Canon Pixma ip1600 drivers required. Lost my origial installation CD. Help!

  Help! Canon Pixma ip1600 drivers required. Lost my origial installation CD. Just got a new PC, but... Cannot use my printer because of mentioned clearly.

  You should be able to download the drivers and software you need to:

  PIXMA iP1600 - PIXMA iP Series
   http://USA.Canon.com/Cusa/support/consumer/printers_multifunction/pixma_ip_series/pixma_ip1600#DriversAndSoftware

  Make sure you get the bit-version appropriate for your Windows 7 system, that is, (x 86) 32 - bit or 64-bit (x 64).

  I hope this helps.

• Windows cannot copy files required for installation. The files may be damaged or missing. Error code: 0 x 80070241.

  I had a lot of trouble trying to install the 64-bit version of windows 7 Home Premium on my 64-bit vista, and my question is multi-part. If it is relevant, it's my 2nd copy of windows 7 I have tried. Initially, I had the problem of not being able to run the installation on two copies with the error "'autorun.dll' could not be found or is damaged. Error code is [0x7E]. "However, I managed to get into with my 2nd copy installation after restarting my computer. Once in Setup, I got another error that stopped the installation that says "windows not could create an installation folder. Error code is 0 x 80070017. "Again, I rebooted my computer and started the installation again, this time following installation was decently through but stopped when I got the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. "I then backed up and restarted my computer and then tried to use the option to install custom but then got the error"E:\sources\autorun.dll is not designed to run on windows or it contains an error. Try to install the program using the original media, or contact your system administrator. "coupled with the error"the file 'autorun.dll' could not be loaded or is corrupt. Error code is 0xC1"again once I restarted and tried the custom option but got the error" Windows has no load the required file WinSetup.dll.» The file is possibly corrupted. To install windows, restart the installation. Error code is 0x3E6. "I restarted my computer and tried the custom triple option more and still have the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. »

  I understand that my problem is very complex, but it seems to be built around a missing or damaged file. Thanks if you can tell what's wrong or what to do.

  Tips for solving common problems when Windows 7 won't install troubleshooting

  1. start Windows Upgrade Advisor to see if there are known issues that might affect the installation and correct them.
  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  2 disable any security software, including anti-virus programs and firewalls.
  3 make sure that your computer has the BIOS and latest drivers.
  4. disconnect all external devices except the keyboard and mouse before installing.
  5. If your computer/motherboard integrated video use and remove the dedicated video card.
  6. If you have a large amount of RAM (memory), try to reduce the amount of RAM installed. 1 GB if 32-bit installation, 2 GB for 64-bit, then replace RAM if the upgrade was successful.
  7. If you have downloaded Windows 7 and it burned a DVD test burn again at the slowest speed possible. It is also possible the download may have errors, you can try to download it again.

  8. check your RAM (memory) to find errors. This can take some time.
  (A) Insert the Windows 7 DVD and restart the computer.
  (B) start from the Windows 7 DVD.
  (C) select your language, and then click Next.
  (D) click on "repair your computer" then select the operating system to fix it.
  (E) click on the link of the Memory Diagnostics in the system recovery menu.
  (F) the computer will restart and your memory is checked for errors.

  9 turn off startup programs:
  (A). Click Start, type MSCONFIG in the search box and press ENTER.
  OK the authorization of user account control and password if necessary
  If you are using XP: click Start, run, and type: MSCONFIG and click OK.
  (B) on the general tab, click Selective startup.
  (C) just below the selective startup, clear the checkbox "Load Startup items".
  (D) click the Services tab, check "Hide all Microsoft Services", and then click Disable all.
  (E) click OK, and then restart the computer.
  (F) try the upgrade again.

  (NOTE: If the upgrade fails and you continue to use your rear security software, then also go back into MSCONFIG and under the general Tower XP/Vista tab, click "Normal startup", and then click OK to exit.)

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• installation of window cannot find drivers (bootcamp)

  First I found the problem on appleSSD.sys, someone said to use oldbootcamp 5.1.5640 (I use macbookpro 2014 middle) to fix

  1 use Boot Camp Assistant, prepare the USB key. Select the first two points, then prepare the drive. Boot Camp Assistant to quit smoking.

  2. in the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  3. spread the former Boot Camp drivers (they are a zip file) on your desktop.
  4. copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.
  5 open Boot Camp Assistant and only select the third option, install Windows 7.
  6. sit and relax because the installation takes place.

  BUT! is not working and I found new window problem installation cannot find drivers

  Sorry for my bad English

  Can you post a Finder of listing of the files on the USB key? Please show only the first level. Just delete the folder AppleSSD64.

• Installation of drivers required on the device target

  Hi, I'm sure I used to know the answer to this, but I paint a white.

  What is the best way to install the software/drivers required on a target computer (which isn't the PC that I have developed on)? Am I right in saying that if I build a Setup program for my application, this should automatically include the necessary drivers? If so, should I install before or after adding the SMU cards to the controller chassis?

  Thank you

  Well Yes, the installer is the way to go. You can include additional installers to include in the installation package. You can also include MAX configurations with installation for if you have defined tasks for information to this unit.

  I suggest you to install the cards first, although I don't know if that makes a difference.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• Upgrade Vista to Windows 7 error: "Windows cannot copy files required for installation. The files may be damaged or missing. Error Code Ox80070017.

  I am upgrading of Windows Vista Home Premium (32-bit) for Windows 7 Home Premium (32 bit) - but getting stopped everytime I try, I end up with a dialog box stating: "Windows cannot copy files required for installation. The files may be damaged or missing. Make sure all files required for installation are available, and restart the installation. Error Code Ox80070017.

  What should I do to resolve this problem and allow full of Windows 7 installation? (my computer is a Compaq Presario V6000).

  Hello

  What installation media you are using?

  Method 1:

  Error 0 x 80070017 translates "CRC error" which means that the files that are copied from the disc are not making it to the hard drive with the same structure, which means that the 'original' the disk files are modified/changed/corrupted while being copied to the location of the 'destination' on your disk during Setup.

  This usually means a bad DVD, or an error reading on the DVD player.

  I suggest you follow the link and check.

  Upgrade Windows Vista to Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-Vista-to-Windows-7?T1=tab02

  Method 2:

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  WARNING: There may be loss of data through an analysis using firewall to eliminate the virus as appropriate

  Method 3:

  I also suggest you to follow the link and check.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Norton 360 diagnosis reported: Microsoft ISATAP Adapter #2 is malfunctioning and windows cannot load the drivers required - code 31.

  Original title: ISATAP adapt #2 does not properly. How can I solve this problem?

  My Norton 360 diagnostic report detected a hardware device unusable.  The device type is: Microsoft ISATAP Adapter #2 and the device situation mentions that it is working properly and windows cannot load the drivers required - code 31.

  I think that it is also affecting my internet connection and disrupt its speed.

  Can you please help with this question?

  Thank you very much
  Tony

  Hi Tony,.

  You can try reinstalling the device driver and check if it works.
  Uninstall and reinstall the device in Device Manager.
  a. Click Start, type devmgmt.msc and press to enter.
  b. Locate the Microsoft ISATAP Adapter device
  c. right-click on the device and select uninstall
  d. restart the computer and check.

  You can also consult the following article:

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/default.aspx/KB/932520

  Hope this information is useful.

• In my report of diagnostic systems that it establishes that there is an error indicating the symptom is "device is not working properly." Windows cannot load the required device drivers. "I don't know what to do.

  Windows cannot load the required device drivers.  It shows the details like Microsoft ISATAP adapter reports "tv_ConfigMgrErr31.  This device won't be available until the problem is resolved.  The Plug-and-Play ID is 17.  What this mean and how can I make the correction of this error and operate?

  Hello

  Control Panel - devices - right click on - UNINSTALL - REBOOT Manager

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you wish
  and on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message
  http://support.Microsoft.com/kb/932520

  Y at - it no devices work not?

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.