Windows 7 installed, the Intel storage driver?

Similar Questions

• Satellite L500 - cannot install the Intel video driver

  Ok
  complete failure of the hard drive, no recovery cd was created, reloaded windows 7, looked up and downloaded the drivers from Toshiba, BUT there are only two video drivers listed, amd and Intel, both marked "for model only supported" its an Intel machine so I tried the Intel driver but it doesn't install, it just closes which I believe if the corresponding material is not found is the default action for these drivers.

  But I'm stuck with 'standard VGA graphics adapt' all other drivers loaded perfectly, (I installed the driver from chipset Intel first and rebooted, so it should be ok but it s not)

  Any ideas?

  Rgds
  SYB

  What Satellite L500 you exactly (L500-xxx)?
  Do you use 32 or 64 bit OS?

• Satellite L500 - 1 7 cannot install the Intel graphics driver

  I can't install drivers for my graphics card on my computer. It's a satellite L500 - 1 7.
  You can see his Setup here:
  Manufacturer: Intel
  model: Mobile Intel GMA 4500 M

  On the site of the intel, they said download the drivers on the toshiba Web site but here does not install the drivers.
  During the installation a message saying:

  «This system does not have the minimum system requirements make the installation of the software.» The installation program will stop. »

  I was able traduct by 'the system has not requiered minimum configuration for the installation of the program. The game program will stop.
  I have download this driver:
  12/02/09
  Chip Set Utility
  Intel Windows 7-64 bits 9.1.1.1019 World Wide

  I'm sure it's good drivers, so what could I do to be able to install this driver I need?

  Sorry for my bad English!

  In General, it is always recommended to use the Toshiba drivers only. Toshiba drivers are tested and adapted to work with graphics placed in the laptop. There are also some overheating protection mechanism and damage graphics card.

  If you check this forum, you will find many users with the same problem. manufacturers of graphics cards write on the pages of own download for portable computers, it is strictly recommended to use the drivers from the laptop manufacturer.

  I think that you think that is good driver, but do you also think that s Toshiba driver is not good or not good enough?

• Satellite A300-RJ1 - cannot install the new graphics driver from Intel page

  Hello.

  Another problem.
  When I use the "integrated" Vista, I can not install the new graphics driver (intel inside).
  Whenever the error message: the driver is not validated by your system, please contact your producer.

  So if I install a clean windows, so I can install the new graphics driver: S and I want to install because it is much more recently than the preinstalled :(

  Hi mate

  You can install this driver, but you need to use different installation procedure.
  You must install it in the Device Manager.

  Here, you can choose Advanced Setup, then choose don't search. I will choose the driver, then point to the driver files that you have stored on the HARD disk and complete the installation.

  But note; I read here that the use of non-Toshiba drivers is always at your own risk

• Installing the Intel driver

  After a fresh install of Win 10 (Microsoft ISO), I tried to install the Intel driver. First of all, everything works and Microsoft installed a driver that seems to work with the installation of Win10. But with regard to the double graph I want install drivers Lenovo. The ATI works without problem, but if I try to install the Intel Lenovo site I got the error that I need to contact the manufacturer for a special driver

  Look in your device manager, see if the Intel HD Video graphics or 4000 Intel are installed. If so, you need not to all other drivers.

  If not yet installed, look for the marked entries red or yellow, right click and select Properties, then the Details tab, then down to hardware ID. Copy the string and paste it into the answer.

  CB

• Laptop bought with windows vista installed, the hard drive was completely cleaned and windows 7 installed, I have to uninstall it and install a genuine windows xp pro - how do this please.

  Laptop bought with windows vista installed, the hard drive was completely cleaned and windows 7 installed, I have to uninstall it and install a genuine windows xp pro - how do this please.

  On Sunday July 25, 2010 10:11:30 + 0000, pc_novice wrote:

  Hi Gordon

  I just downloaded drivers from the Dell website in support of xp

  I have tried to reboot from the XP cd but got the following message when I tried to install

  "This program is blocked due to compatibility issues"

  Program - the installer of Windows

  Editor - Microsoft

  Location: D:\1386\winnt32.exe

  Setup cannot continue because the version of Windows on your computer is newer than the version on the cd. If you decide to remove the version latest Windows that is currently installed the files and settings cannot be recovered"

  I don't want Windows 7 at all so I'm ready to lose all data, so how can I do to remove it?

  You say that you have started from the XP CD, but something is wrong with that
  you do. Just boot from the CD and follow the prompts for a
  clean install. A new installation by formatting the
  drive and does not care what version of Windows is installed (or
  even if any version of Windows is installed.

  Ken Blake

• When I plug my new Seagate Free Agent Desk GoFlex external drive, I get an error message saying that Windows does not recognize the hardware. I'm stuck and need help to install the external hard drive.

  My problem is that the software is supposed to be on the disk but I do not see the player to download. I tried to download the Seagate Manager, but it shows no available disks. Any help will be most appreciated.

  Also, I tried to install the external hard drive on a Windows Vista 64-bit computer and a Windows 7 Home Premium 64-bit.  Same result on both.

  Hello

  I suggest you try to run this under fixit and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  It will be useful.

• Cannot install Windows 8 on the replacement hard drive

  I got the replacement from Dell hard drive which he said would come with Windows 8 and pre-installed drivers. Well, I installed the hard drive and he said no. OS can be found. I didn't have a chance to make my own backup discs, but Dell sent a CD Windows 8 recovery media with the laptop and now with the replacement hard drive.

  When you try to install Windows 8 on the new hard drive, I get to the part where it tells me to choose a partition to install Windows 8 on and none of them will not let me. There are 5 to choose from and I don't know what to do to get past this. The largest partition either 5A about 934 GB of space left out of 1 TB, but as I said I can't choose it or one of the other ones for the installation.

  You just have to click on next, in any case, despite the message?  Otherwise:

  Start on the DVD of Windows 8, instead of install now, click repair your computer, Advanced Options, invites ... when it opens, type the following:

  DiskPart
  Select disk 0
  clean

  Then, try to install.

  The above will remove all the data partition and disk, allowing you to do a clean install on an empty drive (these scores are not required, and Windows will create its own partitions (two) he needs to install and run).

• Error when you try to burn a CD: Windows Media Player cannot burn the files. If the burner is busy, wait until the current task is complete. If necessary, check that the burner is connected properly and that you have installed the latest device driver

  Windows Media Player cannot burn the files. If the burner is busy, wait until the current task is complete. If necessary, check that the burner is connected properly and that you have installed the latest device driver. ???

  I just burn a CD with no problem at all.  Using the same type of CD, brand new, I tried to burn another CD and got this error message:

  Windows Media Player cannot burn the files. If the burner is busy, wait until the current task is complete. If necessary, check that the burner is connected properly and that you have installed the latest device driver.

  I close all programs running, restarted my computer, changed on the devices tab, the speed of burning... everything I know to do and all the things I've read in these forums, no luck... still get the exact same message.  No idea why my CD-writer has decided to stop working for me?

  Hi Cierrajade,

  1. you have any third-party DVD burning software installed on the computer?

  Method 1

  You can use the convenience store open playing and burning CDs, DVDs and Blu - ray discs built in Windows 7 and check to see if it helps you to trouble the CD plays the questions.

  For more information about how to open the resolution of problems in Windows 7, go to the link below and follow the steps.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-and-burning-CDs-DVDs-and-BluRay-discs-Troubleshooter

  Method 2

  If you have any third party CD\DVD software installed on the computer of engraving I suggest you uninstall and check back later if you can burn CDs with success.

  Disc burning: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/disc-burning-frequently-asked-questions

  Method 3

  If the previous step fails, check if you can burn CDs using Windows Explorer

  Burn a CD or DVD in Windows Explorer

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Explorer

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Buning CD error: "Windows Media Player cannot burn the files. ... Install the latest device driver"

  original title: when I try to burn a cd, I get the following message

  When I try to burn a cd, I get the following message: "Windows Media Player cannot burn the files. If the burner is busy, wait until the current task is complete. If necessary, check that the burner is connected properly and that you have installed the latest device driver. "I just burn a cd of two days using a blank of the same pack then, what's the problem?  I installed itunes.  Could be the problem?

  Hi AnnaMiller,

  You can try reducing the burn speed to see if that solves the problem.

  1 open Windows Media Player

  2. click on the burn tab

  3. click on the burn icon options (windows with the box on the right)

  4. Select burn more options...

  5. click on the burn tab

  6. in the general section, change the burn speed.

  7. click on apply

  8. click on OK

  
  

  If this does not resolve the problem, make sure you have the latest drivers for your DVD drive. You can locate the drivers on the Technical Support Web site of the manufacturer of your computer.

  1. download the driver from the manufacturer's website and save it to your desktop so that it is easy to locate.

  2. click on Start

  3. right click on computer

  4. Select Manage

  5. Select Device Manager

  6. develop CD-ROM/DVD-ROM readers

  7. right click on your device

  8. Select Properties

  9. Select the driver tab

  10. click on set to update driver

  11. Select Browse my computer for driver software

  12. click on Browse > Desktop > and then select the file that you saved

  13. click OK

  14. click Next

  
  

  You can also run the Media Player troubleshooting utility to reset the media player to its default settings.

  1. click on Start

  2. click on Control Panel

  3. Select Troubleshooting

  4. Select programs

  5. Select the Windows Media Player settings

  6. click Next

  7. Select apply this hotfix

  8. follow the remaining instructions.

• Windows cannot install the Canon MF8300C series UFRII Lt kernel-mode print driver.

  I have upgraded to windows 8. Now I can't print. Called Canon, ran uninstall it, reinstall and got this error

  Windows cannot install the Canon MF8300C series UFRII Lt kernel-mode print driver. To obtain a driver that is compatible with the version of windows running with the manufacturer.

  Hello

  Thank you for giving us the opportunity to help you.

  Depending on your problem, you have upgraded to Windows 8, but you are not able to print through Canon MF8300C series UFRII you found the error.

  I would like to ask you a few questions about it.

  (1) have you been able to print earlier?
  (2) do you have a driver with this printer support?
  (3) are you an error during the installation of the printer driver?

  Installing the driver in Compatibility Mode

  Please follow the steps below to install in compatibility mode:

  (a) make a right click the driver installation file and select properties and then tap or click on the Compatibility tab.
  (b) check the run this program in compatibility mode for: box.
  (c) press or click the menu drop down and select a previous operating system, and then tap or click OK.
  (d) try to install the driver and verify.

  For more reference, you can go through the link given below.

  You can also search the driver from the link given below.

  http://www.USA.Canon.com/Cusa/consumer/products/printers_multifunction

  Hope your problem is solved now, please write us back if the problem persists.

• Intel storage driver sp46531

  Model two - Pavilion DV7 - portable hard drive

  by default, the storage driver intel - standard AHCI 1.0 serial ATA controller got installed (for IDE ATA ATAPI controllers).

  When HP automatic driver selection suggested to install intel storage driver sp46531, the laptop it picks up well and reading of data has been significantly faster.

  But my second hard drive disappeared from "my computer."    Worse, the "file search / indexing ' stopped.  could not find anything in appearance or Explorer.

  Windows search and services stpped - indexing when tried to start manually, stopped immediately.

  Found some have reported a similar problem with installing Intel storage driver.

  Uninstalled the storage driver Intel - Presto - everything has started to work well

  Hope Intel will take note and suply a new driver soon.

  supervisdr

  the new driver is windows 7 Intel Rapid Storage Technology driver

  http://ftp.HP.com/pub/SoftPaq/sp64501-65000/sp64981.exe

• Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

  Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

  The duplicate thread information:

  Cannot connect Epson scanner/Nikon camera to printer!

  Hi Carolyn has Culp,

  
  Thanks for asking this question to Microsoft Community!
  
  I understand that your scanner and Nikon camera is not getting recognized in windows vista.

  He would be grateful if you could answer these questions. This will help us to a better way to get a resolution of the issue.
  1. have you made changes on the computer before this problem?
  2. What is the brand and model of the scanner?
  3. are you an error message or error code?
  4. is that your other USB devices work?
  I would suggest trying the following methods and check if it helps.

  Method 1:
  

  Try connecting to another USB port and check if the camera is detected or try to plug the camera on another computer.
  Method 2:
   
  Hardware devices do not work or are not detected in Windows: http://support.microsoft.com/mats/hardware_device_problems/en-us
  Method 3:
   
  Remove and reinstall all USB controllers.
  To remove and reinstall all USB controllers, follow these steps:
  (a) click Start, run, type sysdm.cpl in the Open box, and then click OK.
  (b) click on the Hardware tab.
  (c) click the Device Manager button.
  (d) expand Bus USB controllers.
  (e) right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  (f) restart the computer and reinstall the USB controllers.
  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.
  
  Method 4:
  To update the chipset drivers and check if it helps.
  Update a hardware driver that is not working properly: http://windows.microsoft.com/en-us/windows-vista/Update-a-driver-for-hardware-that-isn ' t-work properly
  
  Reference:
  The problems of scanning: http://windows.microsoft.com/is-IS/windows-vista/Troubleshoot-scanning-problems

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• uninstalled the Intel Graphics driver

  I accidentally uninstalled an Intel Graphics driver... How can I get it back?  I have Windows Vista on a Dell inspiron 530.

  Hi Terrell Gibson,

  Usually drivers will install automatically after you uninstall and restart the computer.

  Otherwise, you can check the Dell support to address following link and try to update the latest version of the Intel graphics driver.

  Drivers & downloads for Inspiron 530 desktop PC =

  For more information, you can consult the following article:

  Update drivers: recommended links

  Hope this information is useful.

• How to put Windows 7 on the new hard drive without boot cd? How will I know if 32 or 64 bits? This computer yourself running windows 10?

  * Original title: windows 7 download

  I have a laptop dell M4400 with windows 7 pro OA. HARD drive crashed and I replaced with a new one. How to put Windows 7 on the new hard drive without boot cd? How will I know if 32 or 64 bits? This computer yourself running windows 10?

  It has probably comes with Windows 7 Professional 64 bit.

  You can download a copy of Windows 7 Professional using the following instructions (update of Microsoft recovery software supports downloads with the COA key):

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  You can also use Windows 10 too as you have the right to it as a free upgrade:

  • How to download official Windows 10 ISO files
  • How to: perform a clean installation of Windows 10
  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).