Windows 7 rdp connection error "the request is not supported.

Similar Questions

• Windows ip configuration is an internal error: the request is not supported

  I cleaned up a few viruses out of a Windows XP Professional computer to a customer, and now he can't go on the internet.  When I check ipconfig, I get the following error.

  Windows IP configuration
  An internal error has occurred: the request is not supported.
  Contact Microsoft technical support for more help.
  additional information: host name of request impossible.
  So I googled some results. Have replaced the TCPIP.sys file with one from another computer, I still get the same message.  I don't have a windows XP original disk to put it into recovery mode.
  I also ran the command "netsh int ip resetlog.txt" but which did not help either.  I saw on another blog.
  The NIC is to see that there is a power cable plugged into it as well.  Help, please!
  Thank you
  Trever

  Hello Trever,

  Follow the methods and check:

  Method 1: You can refer the following Microsoft Knowledge Base article and check.

  "Error 1068" error message when you try to enable Internet connection sharing

  http://support.Microsoft.com/kb/827328

  Method 2: Try the SFC (System File Checker) scan on the computer.

  To run the System File Checker tool, follow these steps:

  a. click Start and click run, then type cmd in the box start the search.

  b. right click on cmd in the list programs, and then click run as administrator.

  c. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  d. at the command prompt, the following line and press ENTER:

  sfc/scannow

  For more information, see the article:

   

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  http://support.Microsoft.com/kb/310747

   

  File system (CFS) Checker

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/system_file_checker.mspx?mfr=true

  Let us know if that helps.

• Windows live mail send error "the server does not support an SSL connection. Server error 250.

  Original title: Windows live mail error send

  Cannot send mail to Windows Live Mail.  Error message... The server does not support an SSL connection. Server error 250. Server - * address email is removed from the privacy *. Windows Live Mail error ID - 0x800CCC7D. SMTP Protocol.  Port 25.

  It's better, thank you. This message is not from the BT Server; It comes from your Avast antivirus which is intercepting your mail. You would be well advised to turn off the Avast Mail shield; It does not add any additional security if you don't by attention elsewhere, and can cause problems.

  I see that it is the record of mail in bulk that because of the problems in this case. Connect to the Web e-mail account and clear the items junk and deleted records.

  BT is recommended to use SSL, but your original question indicated that SSL was not taken in charge for SMTP on port 25. I think we'd better go on all your settings. Recommendations of BT are on this page: BT email: what are the settings for outgoing and incoming mail servers?, but they only work if you disable Avast scanning mail.

  Right-click on the account name in the folders pane, and then select Properties.

  • Under the servers tab, make sure that my server requires authentication is selected.
    Select connect with authentication in clear text.
  • On the Advanced tab, select this server requires a secure connection (SSL) for both servers.
    Make sure that the incoming (IMAP) port is 993 and port for outgoing (SMTP) is 465.

  When you've made all these changes, close Windows Live mail and wait five minutes for the program do its cleaning and save the modified settings. Then, restart the computer and make sure that the Mail of Avast shield is always off.

  Launch Windows Live Mail, then dial a new test message and send it to yourself. Post a new message in your response.

• I get an error "the server does not support an SSL connection" with a code of error 0x800CCC7D in Outlook express.

  I followed Bruce Hagen and still cannot send to the OE section. Reception is no problem. When I try to send I got the following error msg: "the server does not support an SSL connection. "Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, server response: ' 250 8BITMIME ', Port: 25, secure (SSL): Yes, Server error: 250, error number: 0x800CCC7D. I tried to change the port for outgoing to 456. When I do so I get this error msg: failed to connect to the server. Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, Port: 456, secure (SSL): Yes, Socket error: 10060, error number: 0x800CCC0E.  Is there a cure for this. He just started two days or at least that's when I noticed I cud not send. If you can help me I will appreciate it more. Thank you.

  JP banks

  Original title: cannot send using OE 6. Reception Ok.

  Hi JPBANKS,

   

  Thanks for keeping us posted and share this information with us.

  Glad to know that the problem is solved. Do not hesitate to contact Microsoft Windows Forums for issues related to Windows in the future.

• Get this error "The Office does not support the requested protocol display."

  Just built a new environment of view 4.5 and became "The Office does not support the requested protocol display" when trying to use the client to connect through PCOIP, but works very well with RDP... What Miss me?

  Wwill price points righ away.

  When you installed the Agent of 4.5 view you ensure that PCoIP components have been selected?

  -Mike

• In the error message is Vista "Windows Media Player cannot play the file, might not support the codec used to compress the file.

  It worked very well what place please?

  * original title - Window Media Player cannot drive cannot read the file the player could does not load the file or may not support or does not support the codec used to compress the fichier.*

  Hello

  1. what changes have been made to your computer before the problem?
  2. the problem occurs on a particular file?
  3. What is the format of the file you want to play in Windows Media Player?

  You may encounter this error message for the following reasons:

  (a) the file type is supported by the drive, but the file was compressed by using a codec that is not supported by the player.

  (b) the file might have been encoded with a codec that is not supported by Windows Media Player. If this is the case, Windows Media Player cannot play the file.

  Windows media player will play only the files and videos only if it supports this type of file.

  Please see the bottom of the article that gives you information on the types of media files that supports Windows Media Player.

  http://support.Microsoft.com/kb/316992

  If the files are not supported by Windows media player, then you will need to use a few players from third party that supports this file format.

  WARNING OF THIRD PARTY SOFTWARE

  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  See the link below for more information on the codec.

  Codecs: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/codecs-frequently-asked-questions

• Windows Vista computer connects to the internet, but not ping to auto DHCP name

  Trying to get my Vista machine to have the file and printer sharing, I can see attached machines, and they can see the Vista machine, but does not connect to the computer.  The Vista machine will not see public folders with error code: 0 x 80070035 the network path was not found.

  Ping the DHCP name provides:

  Main2 ping [fe80::12:f74:b94e:94fb 8%] of 8% with 32 fe80::12:f74:b94e:94fb
  YTES of data:
  General failure.
  General failure.
  General failure.
  General failure.

  Ping statistics for fe80::12:f74:b94e:94fb 8%:
  Packets: Sent = 4, received = 0, lost = 4 (100% loss),

  Ipconfig/all

  Windows IP configuration

  Name of the host...: Main2
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Belkin Wireless G Desktop Card
  Physical address.... : 00-11-50-D6-32-97
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::e497:9802:e6a6:40ce % 10 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Tuesday, October 21, 2008 23:06:50
  End of the lease...: Thursday, October 23, 2008 11:06:50
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e50:12:f74:b94e:94fb (area
  ED)
  Address IPv6 local link...: fe80::12:f74:b94e:94fb %8 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {E71A931D-A587-49DD-BF49-209236344
  523}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Any help?

  
  

• upgrade to vcenter 5.5 to 6.0 error: the database driver not supported

  When I try to upgrade vCenter of 5.5 to 6.0 I get error:

  Error: database driver not supported

  c:\Windows\system32\sqlncli.dll

  Solution: Make sure you use vCenter Server with supported driver

  vCenter used SAerver of SQL 2005 Express. I tried the upgrade SQL Server 2008R2 Express, but the error is the same

  What ODBC drivers?

  Those who are actually supported?

• I'm trying my computer, but for some reason any that it won't let me back. Error "the request could not be performed because of an i/o device error (0 x 80070450)"

  Original title: I try my computer, but for some reason any that it won't let me back. and I get an error message

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: have problems with window vista home premium

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello Mipregunta,

  Thanks for your quick response! I suggest that you try to visit the following article for steps on how to solve your problem:

  http://support.Microsoft.com/kb/952272

  Please let me know if this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Windows 7 wireless connection to the field is not possible if the connection to the account not set cache

  We have a Cisco wireless network if a user is not logged previously wired and caching fails.    Is there a requirment W7 that successfully connect before it will make a wireless connection to authenticate on a domain controller?

  Kazakovvictor,

  Thank you for visiting Microsoft Answers!

  The question you have posted is related to networking in a commercial environment and would be better suited to the TechNet community.

  Please visit the link below to find a community that will support what ask you:
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 0x8007045D error: the request cannot be performed because of an i/o device error

  I brought a new seagate hard drive I tried windows backup to the windows image. But I got error 0x8007045D error: the request could not be performed because of an i/o device error. I tried safe mode and clean boot state, but nothing works. I'm not able to access backup windows in safe mode. In the State of clean boot, I get the same error

  Hello

  Welcome to the Microsoft community.

  It seems that you are unable to run the Windows backup utility on the new external hard drive. It would be great if you can answer the following questions:

  1 have had any changes made on the computer before the show?

  2 are you able to access the external hard drive? If it is detected by the computer?

  To resolve this problem, I suggest to refer to article and follow these steps:

  Error message when you try to perform a full backup on a Windows Vista-based computer: "the application cannot be performed because of an i/o device error."

  http://support.Microsoft.com/kb/952272

  The article also applies to the Windows 7 operating system.

  Note: when running chkdsk on the drive hard if bad sectors are found, it tries to repair this sector and if all the available data may be lost.

  If you are always faced with the question, please answer and we will be happy to help you.

  Thank you.

• Errors running SQLIOSim - Simulator/o SQL - error: 0x8007045D error text: the request could not be performed because of an i/o device error. Description: failed to get the info from cache drive to C:\

  When we execute SQLIOSim on a Server Windows 2003 VM hosted on an ESX 3.01 or 3.5 server, you get the following messages:

  Error: 0x8007045D

  Text of the error: the request could not be performed because of an i/o device error.

  Description: Failed to get the info from cache drive to C:\

  Anyone know what is the cause or how to solve the problem (if it is a question)?

  Thank you

  Had the same error and found this blog:

  http://blogs.msdn.com/psssql/archive/2008/01/14/SQLIOSim-error-request-could-not-be-performed-unable-to-get-disk-cache-info.aspx

  It will be useful.

• The request is not taken in charge (0 x 80070032) while trying to make a backup on an external hard drive

  Original title: the request is not supported (0 x 80070032)

  This is the answer I get trying to external and hard disk backup.

  • I have all of the products norton... I use ms essentials
  • My hd is big enough for this make upward
  • I use power power ac

  Hello
   
  Remember to make changes to your computer before the problem?
   
  Follow these steps and check if the problem persists.
   
  Step 1:
   
  You can check if the backup and restore services are started when you try to make a back up of files.
   
  a. click on start
  b. in the start search box, type Services
  c. click right on - RUN as ADMINISTRATOR

  These are the services that must be running when you try to make a return to the top.

  Automatic started Windows event log
  Task Scheduler started auto
  Backup Windows stopped manual
   
  Step 2:
   
  You may want to consider temporarily disabling your security software and then try to save.
   
  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Step 3:

  I would also say that you check your disk for errors.

  Check a drive for errors

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  WARNING:
  Important: All performing hard disk the disk check if bad sectors are found on the disk hard disk check is trying to repair this area if all available on which data may be lost

  Let us know.
   
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Error: The system does not meet the installation requirements. the software does not support this versio

  1 LASERJET PRO CP1525nw

  2. Windows XP

  3 error: the system does not satisfy the installation requirements. the software does not support this version of Windows. Search hp.com for more information on this product compared to this error.

  4. no change

  Thanks, but I arrived on the support desk and the problem was that for XP, you use the printer Install "Option in the drop down box and then select the"TCP/IP"Port, if you choose the option 'Wireless'.

• The system does not support the mode full screen for cmd

  Respected Sir/Madam

  I am user of Windows vista HOme basic... .also I have Windows 7 user... I'm basicllly, a student in computer engineering...

  I get an error "The system does not support the mode full screen" for cmd.exe in C++ turboo or JDK.. .then I getproblem by entering n compiled the program...

  my PC configuration is

  :-AMD 6000 + dual core Athlon 64 X processor

  Monitor:-Viewsoni

  RAM :-1Go

  Please give me a solution to problem 4 I wanted to run cmd mode full screen...

  your help will be appreciated by me highlly...

  thanking you

  Philippe

  Vista + do not support a command prompt full screen, as indicated by the message. You can manipulate the available to the command window to specify the width and height to be as big as you want, but this isn't quite the same thing...