Windows could not start. Status: 0xc000014c

Similar Questions

• PC with Windows Vista does not restart after installing updates, "Windows could not start...". "File:\Windows\system\winload.exe status: Oxcoooooof.

  Last night, I installed Windows updates on my HP Pavilion dv6227cl and now Windows will not boot.  I get the message "cannot start Windows.  A recent hardware or software change might be the cause.  File:\Windows\system\winload.exe status: Oxcoooooof Info: the selected entry could not be loaded because the application is missing or damaged.  I DO NOT have the Windows Setup disc.

  Hello

  I suggest you borrow the CD of windows vista to your friends

  Method 1:

  Step 1:

  I suggest you check in safe mode.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  If you be able to start your computer in safe mode, I'd say make clean boot and check.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, make sure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I also suggest you to see link and check.

  Error: Windows could not start. A recent hardware or software change might have caused the problem after installing Windows updates

  http://support.Microsoft.com/kb/2674065

• Windows could not start. Winload.exe corrupted

  Been having some problems with my Equius has therefore decide to start, F8 and do a system restore toshiba.

  Started and started to format the drive. All of a sudden he projected blue.

  The problem is now I can not even start until now to get the recovery/restore option. I get: -.

  Windows could not start. A recent hardware or software change might be the
  cause...

  File: \Windows\system32\winload.exe
  Status: 0xc000000f
  Info: The selected entry could not be loaded because the application is
  missing or damaged.

  Not sure how it all works, but I guess that recovery stuff are stored on a separate partition. Problem is I guess you must be able to start to load windows before you even get to do this?

  I downloaded and tried a boot with no joy, and of course vista recovery disk, toshiba provide a vista disk. How the hell can I recover from this situation?

  Hello!

  If you are not able to get in the boot menu for HARD drive recovery, you must use a Microsoft Vista disc to reinstall the OS.
  Or you use the Toshiba recovery disc but I think you forgot to burn the disk because normally you get a message (recovery point) you want to burn the disc.

  However, you can order a Toshiba Toshiba recovery disc directly:
  https://backupmedia.Toshiba.EU/landing.aspx

  Good bye

• Windows could not start on Satellite L510

  HI :)

  I'm not very tech savvy, I've only had my laptop a month. And yesterday, when I turned it back on I got this message...

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem: Insert your windows installation disc, and then restart your computer
  If you do not have the disk, contact your manufacturer computer or system administration.

  file: \boot\bcd
  status: 0x000000f
  Info: an error occurred trying to read the boot configuration

  I have been all over these forums and the internet looking for a solution, but no luck. It's the weekend, so I can not communicate with the service line.
  I would appreciate a process step by step what it is, that I need to download or reset. I do not have the windows installation disc, because it did not come with my laptop.

  I really appreciate your help in advance ;)

  Hello

  Well, the error message says everything to me. Insert the Windows disk * or * contact manufacturing (Toshiba). ;)

  By the way: it would be interesting to know if you can boot into safe mode. Check it!
  If so, you may start the HARD drive recovery. Therefore, select Repair my computer in the Advanced Start menu and follow the instructions on the screen.

  Yes, with the laptop didn't come a disc, but you can create one!
  Please read the operating manual always first.

  Now it s too late to create such a floppy, but you can order directly into a new Toshiba:
  https://backupmedia.Toshiba.EU/landing.aspx

• Windows could not start the background service Itelligent transfer service on local computer. 87 error: The parameter is incorrect

  I had a crash dump blue screen, tried solutiions to the problem and told me to go to windows update and download all windows updates. downlownloading all updates failed and I got the error.

  Code 80246008

  Click on get help with this error and was instructed to go to services and start the background intelligent service services, it gave me the error message;

  Windows could not start the background service Itelligent transfer service on local computer. 87 error: The parameter is incorrect

  Not very computer savvy! no idea what it all means or what I would do to this topic! Thanks a lot for any help

  Try this:

  To change or restart the Service (BITS) Background Intelligent Transfer

  1. Open administrative tools by clicking the start , clicking Control Panel, clicking system and Maintenance, and then clicking Administrative Tools.

  2. Double-click Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. Right click on the service of Intelligent Transfer (BITS) background and then click Properties.

  4. Under the tab general, next to startup type, make sure that automatic (delayed start) is selected.

  5. Next to Service status, check whether the service is started. If not, click Start.

• Windows could not start. A recent hardware or software change might be the cause.

  I have a Toshiba M300 and it fails to start. Here's what he said.

  Windows could not start. A recent hardware or software change might be the cause.

  If the files in the window were damaged or configured incorectly, startup rapir can help diagnose and fix the problem. If the power was interrupted during startup, choose start windows normally.

  Lanch Startup Repair

  Start window normally

  Well, I had two options... and nothing works. It gets stuck just on loading thingy, where it says MICROSOFT WINDOWS and keeps loading... I leave for 2 days and he continued make it... and it also won't let me restore my computer...!

  PLEASE HELP :(

  Hi Suzanna2001,

  Were present from recent changes to the system before the show, such as adding new hardware or software (including Windows Update).  You have access to a Windows CD/DVD?  Run the startup from the CD/DVD repair.  There is also an option to perform a restore of the system on the CD/DVD.  If no option is the problem, follow the steps below:

  1 1 demarrer start from the Windows 7 DVD, select your language and keyboard options, select repair your computer, and then select command line.

  2. from the command prompt, run the following command:
  DISM image:c:------/ Get-Packages

  This will produce a list of updates installed and packets.  They will look like this:

  The package identity: Package_for_KB978262 ~ 31bf3856ad364e35 ~ x 86 ~ ~ 6.1.1.0
  Status: installed
  Output type: security update
  Install time: 02-11-2010 13:01

  3. find the most recent and then make a note of the identity of the package.

  4 run:

  DISM image:c:------/ Remove-Package /PackageName:Package_for_KB978262~31bf3856ad364e35~x86~~6.1.1.0 (name of the update from the previous step)

  Until it is complete, you will get a status of the collection.

  5. restart your PC.

  You want to start with the most recent, and then remove them one at a time to find the problem update Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows could not start. A recent hardware or software change might be the cause. (vista)

  I've updated pctools free and there was a mistake by because it came when the computer restarts,

  Windows could not start. A recent Ministry of hardware or software may be the cause. To solve the problem.

  1. Insert the windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "repair your computer".

  File: \windows\system\drivers\PCTCore.sys

  status: 0xc0000098

  Info: windows could not load a critical system driver is missing or corrupt.

  I tried I went to my computers startup options advanced and tried to run in safe mode, but the same previous screen came. Each option in my boot options is the same screen. I realize that to solve this problem, I might have to reload my OS together.  I tried to put what I believe to be the installation disc in and restart but it starts and says the same message. I don't know how to start from the DVD.

  Someone at - it solutions?

  Change the boot order in the BIOS to boot from the CD drive first.
  How to change the boot sequence in the BIOS
  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  C:\windows\system32\drivers\pctcore.sys file information
  http://www.file.NET/process/PCTCore.sys.html

• I get a message from Windows could not start whenever I turn on my computer.

  Original title: Windows could not start.

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  (1) Insert your disc to Installations of Windows, and then restart your computer
  (2) select language settings, and then click "next".
  3) click on "repair your computer".

  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.

  File: \Windows\system32\drivers\volsnap.sys

  Status: 0xc0000221

  Info: Windows could not load a critical system driver is missing or corrupt.

  ***
  Whenever I restart the computer, this is the window that appears and I can't go in front of her.  It cannot boot without failure, or any other mode.

  ANY help is appreciated! I don't have the original installation disc for Windows.  And since I can't go beyond that I can't the product key...

  My computer is a Sony Viao VGN-N350E

  mnmshemi

  Hello

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  and if all else fails and you need to reinstall vista are the normal methods for computers preinstalled vista portable

  Contact the computer manufacturer and ask them to send vista recovery discs

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

• Windows could not start - black screen

  My laptop does not start - I have a black screen with the message

  Windows could not start.  A recent hardware or software change might be the cause.

  
  

  File CLFS. SYS

  Status: 0xc00000e9

  Info: Windows could not load because a required file is missing or damaged.

  I ran the Vista startup repair disk, but results from that start-up cannot repair this computer automatically.  root cause found: critcal C:\CLFS boot file. SYS is corrupt

  I can't start in safe mode - when I try it starts to list files, stops after about 5 and then sends me the black screen message.

  Hello

  To begin with, would not be clfs.sys C:\, it would be under C:\Windows\System32. This could indicate one of the following two issues:

  (1) your boot sector is damaged.

  (2) you have a virus masquerading as a legitimate system file.

  For one, the first thing you should try are the steps detailed here: http://support.microsoft.com/default.aspx/kb/927392?p=1

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Windows could not start after activating the boot.

  Hi all

  I have a very serious problem.

  A few lost technology from Microsoft asked that I have to do the following:

  http://support.Microsoft.com/kb/929135.

  Immediately after the restart, I was confronted with the following message:

  Windows could not start.

  Status: 0xc000000e

  Info: A required device is not connected or is not accessible.

  Startup Repair does not work. -Root cause found: the partition table has not a Sys component validates.

  System Restore does not work - the system cannot find the specified file (0 x 80070002)

  Bootrec - rebuildbcd works no item was not found.

  Bootcfg does not work - could not open the TRUNK. INI file.

  Bcdedit does not work - the requested system device cannot be found.

  GParted does not work - cannot load the ntfs module: invalid argument.

  How can it be fixed, please?

  It is an extremely urgent situation which must be resolved immediately, because I use this computer for work and need to return to work on a large commercial project Monday. Forget the original question that MS tech was trying to 'help' with, everything what I need now is to be able to get into Windows, or even just make this record available and accessible on the LAN computer.

  Hi all, thank you for the advice.

  Problem has been resolved after a cold start.

• Windows could not start HomeGroup Listener

  Windows could not start HomeGroup Listener on. Local computer. For more... the 2147023817 service-specific error code. I also have a problem with the provider of the home group. . I tried almost every thing. .. .i can join the Group of home. Thank you

  Don t think it has something to do with the Toshiba laptop.
  It looks like more because of Microsoft.
  Found this discussion in the Microsoft forum:
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/thread/453c3e1d-A980-417C-a6e6-d4c5c1af79a1

  _Someone wrote there: _

  + For those of you who could not startHomeGroup service listener and HomeGroup provider to ensure that these services are started and set to automatic: +.

  +-Function Discovery Provider Host +.
  +-Function Discovery Resource Publication.

  + (Activate in the following order): +.
  +-Peer Networking Identity Manager +.
  +-Peer name resolution protocol.
  +-Peer Networking Grouping +.

  + If these services are disabled this is maybe the reason why you couldn't create a homegroup. +

• Equium A300D - 16 c - Windows could not start

  I have a Toshiba Equium A300D - 16 c, and all of a sudden it turns on and goes on the windows boot and said Manager that Windows could not start and he won t let do me something else.
  I put really know what to do and all my United work is about it.

  It says to put the installation disc windows but it s does don't not to all drives what so ever.

  If anyone could help I'd be grateful
  Thank you

  You can start Windows in safe mode?

• Satellite C660D froze and won't start - Windows could not start

  OK, enough of the more dense person you will ever likely to meet when it comes to things like that. but will try my best to explain.

  There are a few days that my laptop has frozen on me on me having to turn it off and start it again by the power button. When I started again the message below appears.

  WINDOWS ERROR RECOVERY
  Windows could not start. A recent hardware or software change might be the cause.
  If windows files have been damaged or misconfigured in, Startup Repair can help diagnose the problem, if the power was interrupted during startup upward, choose start windows normally.

  -Launch start repair (recommended)
  -Start windows normally

  When I press launch Start up repair that it goes to a screen with a big cursor (that you can move) but nothing happens.
  When I pressed the start windows normally put it went through the windows logo while starting but then stops at this point.

  My question is, is - this easy to fix & if not where is the best place to consider to get fixed. Said I was dense enough: p

  Thanks for looking

  Dean

  > My question is, is - this easy to fix & if not where is the best place to consider to get fixed. Said I was pretty dense

  I think its easy to correct, but you'd need a Toshiba recovery disc.
  Have you created one in the past?

  If not, try to start the HARD drive recovery: turn on the device, press F8. Now choose fix my computer.
  Now new window should open, and here you must select Toshiba HDD recovery option. This would create the laptop back to factory settings.

  In case this isn't possible, you will need to boot from a recovery disk to reinstall the system.

• I have error #1053 windows could not start the printer spooler. Help

  Windows could not start the printer spooler. I received the error #1053.
  whatever it is sent to the printer never finished loading and crashes to the top
  my computer, so I have to re - start.

  This forum is for posting comments on the web site of Microsoft Answers, is not for technical questions.  Ask your questions to http://answers.microsoft.com/en-us/windows/forum/hardware, making sure that you specify your Windows version in the drop-down lists at the top.

• Once I turned on the computer I got the following message: Windows could not start because the following file is missing or damaged. System32\Drivers\Ntfs.sys

  I just download Microsoft Office 2010 Professional and then turns off the computer with XP operating system. Once I turned on the computer I got the following message:

  Windows could not start because the following file is missing or damaged;

  System32\Drivers\Ntfs.sys

  You can try to repair this file by starting Windows Setup using the original Setup CD

  Select 'r' in the first screen to start repair.

  Then, I started the computer with the Original installation CD and press 'r' by following the instructions. Then, I received this message:

  1: C:\WINDOWS

  Which Windows installation you want to connect?

  (to cancel, press enter)

  What do I put here?

  You must first start on doing something so USB drive a bootable Hiren.

  Here's how:

  I'll recommend you use Hiren boot CD (it will go also to a flash/USB stick/USB).

  It's good for you, because there a lot of tools more on that on the Recovery Console CD of XP, doesn't your administrator passwords and you will not have to futz round in your BIOS, if any afflicted system has SATA drives - Hiren can deal with this.

  You will have a bunch of great tools that you have in XP... Recovery Console an editor of the register, adjustable password and an office that resembles Windows XP so you will feel comfortable flexibility.

  You can easily copy your personal data (documents, pictures, music) to an external drive.

  A system of work, start by downloading the latest version on Hiren Boot CD from here (it is a substantial download but worth it):
  http://www.hirensbootcd.org/download/    (look to the bottom of the page).

  Unzip the Hiren to a folder where you can find it.  There's a Hiren. BootCD.15.x.iso that you have to then.

  Hiren was instructed to make a bootable USB drive that you can use, but it takes you first burn the .iso to a CD image file and a few other measures, so I suggest another way and here's how:

  Download RUFUS 1.3.2 or whatever the latest version is here (read a few things on the page so you can learn more on this subject):

  http://Rufus.AKEO.IE/

  I will warn to be careful that don't accidentally format you a hard disk - don't forget your USB key is in and know what the drive letter!  This part makes me still a little nervous, so be careful.

  Launch of RUFUS and all default values should be fine for the device, choose letter of your USB drive, quick tag format FAT32, it if you want and in the Format options box, click on the little icon that looks like a CD and a window will open.  Navigate through this dialogue to point to the folder that contains the Hiren. BootCD.15.x.iso that you have unpacked above and the box should change to say the image ISO (RUFUS includes the Hiren ISO file).

  Double check you have the right device selected in the top (NOT you HDD) click Start, acknowledge receipt of the warning and let it finish (it will take a little time) it copies the files.   Hiren ISO is also a good size.

  When RUFUS is finished, it will say "DONE" at the bottom.

  Put the USB in the afflicted machine and reset/reboot and regardless of the button you press to get a boot menu where you can select the USB drive as first boot device (it's F11 for me).  If you do not see a start menu choice, you will need to set your BIOS to boot from USB first instead of the HARD disk.

  When the Hiren menu displays, choose the XP Mode of Mini and it will start loading (slowly from a USB key) and finally, you should see a windowsy looking for office.  You should recognize the part and feel uncomfortable, but it is not your office - the office of the Hiren!

  Remember: you do not start on your hard drive, - you started in the Office of the Hiren.

  A way to check the drive for errors is to open my computer and right-click on your afflicted player and choose Properties, tools, error, check checking now... put a check mark in the boxes and then start.

  Sometimes that works, then you can also click on start, run and in the type box:

  cmd

  Click OK to open a command prompt window and enter the following command (assuming that XP is installed on your C drive)

  CHKDSK c: /r

  This disk check can last a long time (perhaps several to several hours) depending on the size of the volume, the amount of data on the volume and what the disk check finds to do.  You may need to run more than once.