Windows Driver crash condition caused by ntoskrnl.exe

Similar Questions

• Windows 8 BSOD caused by ntoskrnl.exe

  Hello.

  I get a lot of the dreaded BSOD lately.
  From the beginning I thought that it's nvidia drivers. Update of those fixed everything except a BSOD I get.
  Now I get the same BSOD, and it is caused by ntoskrnl.exe and playback memory problems.
  I've been all around you are looking for assistance and use of memtest86 without result.
  The Msinfo32 and .dmp files are located here: DMP.zip 
  Anyone have any idea what may be causing this?
  I couldn't find the RAM that I use in the compatibility table for the motherboard. So that's what I think may cause the problem.
  Any help is greatly appreciated.
  Kind regards
  Arve

  Hi Arve,

  All attached files of the DMP are the bug check IRQL_NOT_LESS_OR_EQUAL (a) .

  This indicates that Microsoft Windows or a driver in mode accessed kernel memory paged at DISPATCH_LEVEL level or above.

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high. The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If we look at the call stack:
  
  STACK_TEXT:
  "fffff880 '0335caf0 fffff880' 06a4d817: fffff880 00000000' fffffa80 ' 00000008 fffffa80 ' 12fdbe10 00000005' 00001f80: nt! KeSetEvent + 0x2ad
  fffff880 '0335cb60 00000000 fffff880': fffffa80'00000008 fffffa80 '12fdbe10 00000005' 00001f80 fffffa80' 1458a6a0: MBfilt64+ 0 x 1817
  fffff880'0335cb68 fffffa80'00000008: fffffa80 '12fdbe10 00000005' 00001f80 fffffa80 '1458a6a0 fffff800' 9bc62d4c: 00000000' 0xfffff880
  fffff880 '0335cb70 fffffa80' 12fdbe10: 00000005' 00001f80 fffffa80'1458a6a0 fffff800 '9bc62d4c fffffa80' 1458a6a0: 0xfffffa80'00000008
  fffff880 '0335cb78 00000005' 00001f80: fffffa80 ' 1458a6a0 fffff800 '9bc62d4c fffffa80' 1458a6a0 fffffa80 ' 1458a6a0: 0xfffffa80'12fdbe10
  fffff880 '0335cb80 fffffa80' 1458a6a0: fffff800 ' 9bc62d4c fffffa80 '1458a6a0 fffffa80' 1458a6a0 fffffa80 ' 12fdbe10: 0 x 5 ' 00001f80
  fffff880 '0335cb88 fffff800' 9bc62d4c: fffffa80 ' 1458a6a0 fffffa80 '1458a6a0 fffffa80' 12fdbe10 fffff880 ' 02fc9f00: 0xfffffa80'1458a6a0
  fffff880 '0335cb90 00000000' 00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: nt! ViPendingCompleteAfterWait + 0xc4

  Cannot load the image MBfilt64.sys, 0n2 error Win32
  WARNING: Unable to verify timestamp for MBfilt64.sys
  ERROR: Module load completed but symbols can be loaded for MBfilt64.sys
  Probably caused by: MBfilt64.sys (MBfilt64 + 1817)

  ^^
  Driver Realtek HiDefinition Audio (referred to as Creative Audio Driver file).

  If we run a lmvm on your:

  4: kd > lmvm MBfilt64
  start end module name
  fffff880 '06a4c000 fffff880' 06a5a000 MBfilt64 T (no symbol)
  Loaded symbol image file: MBfilt64.sys
  Image path: MBfilt64.sys
  Image name: MBfilt64.sys
  Timestamp: Thu Aug 30 23:40:32 2009 (4A7267B0)

  ^^, Yours is dated 2009 ~ The most recent is AFAIK as early as September 2013, via - Realtek site

  http://www.Realtek.com.tw/downloads/downloadsCheck.aspx?langid=1&PNid=24&PFID=24&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  To update this driver as soon as POSSIBLE.

  -----------------------------------------------------------

  In addition, to provide peace of mind regarding your request of RAM. If you receive a card mother and they have a list of the RAM compatible in the manual, etc., this is called a QVL (qualified suppliers list). It is simply a list of RAM which has been tested internally and is PROVING to be quite compatible 100%. If the RAM is not on the list, it is not by all means, implies that the RAM will be inconsistent and cause problems. Actually today is very rare. Your RAM doesn't seem to be the issue at all in these accidents.

  Kind regards

  Patrick

• BSOD caused by ntoskrnl.exe - bug DRIVER_POWER_STATE_FAILURE

  Hi all

  I'd appreciate help with my laptop problems I don't know neither the cause nor the solution...

  For several months, my laptop refuses to close directly. I explain: when I want to stop it, any reboot my laptop and I have to stop him again so he can actually stopped. In addition, at each attempt to stop / restart, I have this incredible Blue Screen of Death for 15 to 20 minutes, then my laptop actually restarts. Once it has restarted, it works normally for 3 minutes and then freezes for a duratation ranging from 5 min to 40 min...

  In addition, since the beginning of these problems, my laptop detects no USB devices (mouse, external driver...)...

  Please help me, this situation is driving me crazy...

  My laptop is an Asus ux32v and runs on 64-bit processor - i5 3317U and Windows 8 (if it helps).

  Here is the link to my minidump files:

  https://www.dropbox.com/sh/ix3bf3v7aog2xz5/AAAcgX3yNBDWVAj5JXs9JNzSa?DL=0

  I tried to open these files with software like BlueScreenView but couldn't do much about it. What I realized is that it was caused by ntoskrnl.exe.

  Thank you in advance for your help!

  MS

  It is possible because you do not remove it completely.  He was always loaded into the current DMP file

  You do not update to win 8.1.  I'll wait until you do.

• Windows 8 blue screen - DRIVER_POWER_STATE_FAILURE caused by ntoskrnl.exe

  I have a new Sony Vaio Pro and have experienced outages of system 3 times.  All the accidents that happened after I've restored from hibernation and were related to the bug check DRIVER_POWER_STATE_FAILURE.  After the first two accidents, I ran Sony diagnostics on the memory and hard drive SSD and they passed the test.  I even sent my Vaio Pro to the repair depot to Sony for a test on the memory, hard drive and other hardware and they all passed.

  I found my Vaio Pro last Wednesday and updated the Windows 8 from scratch.  This morning, after the resumption of hibernation, I realized my Bluetooth mouse did not work.  So I stop the laptop hoping a restart could solve the problem.  However, it took almost 5 minutes before they would stop and restart Windows gave a warning:

  "Experienced problem with closed Windows.  Your PC fell on problem.  This problem case your PC to restart.

  BlueScreen Viewer it pointing DRIVER_POWER_STATE_FAILURE caused by driver ntoskrnl.exe.

  BlueScreen details as follows:

  A problem has been detected and Windows has shut down to prevent damage to your computer.

  The problem seems to be caused by the following file: ntoskrnl.exe

  DRIVER_POWER_STATE_FAILURE

  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

  Check to make sure any new hardware or software is installed correctly.

  If it is a new installation, ask your hardware manufacturer or software, the Windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware or software. Disable the BIOS memory options such as implementing caching or shading.

  If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options and then

  select Safe Mode.

  Technical information:

  STOP: 0X0000009F (0X000000000000012C, 0XFFFFFA80196707C0, 0 X 0000000000000004, 0XFFFFF880009EC810)

  Ntoskrnl.exe - address 0xfffff80189072106 base at 0xfffff8018901e000 DateStamp

  0x51a966cd

  Here's my minidump file:

  https://DL.dropboxusercontent.com/u/1928780/093013-7531-01.dmp

  File Msinfo32.NFO:

  https://DL.dropboxusercontent.com/u/1928780/Msinfo32.nfo

  Dump file memory (do not know why this file is nearby big 550MO):

  https://DL.dropboxusercontent.com/u/1928780/memory.dmp

  p.s. I think this may have something to do with my Bluetooth driver I had experienced many times the Bluetooth driver has been disabled by Windows and the event viewer reported "the Local Bluetooth is not indeterminate way and will not be used.  The driver has been unloaded. "

  Thanks in advance,

  William

  Hi William,.

  The attached file of the DMP is the error checking DRIVER_POWER_STATE_FAILURE (9f) .

  This bug check indicates that the driver is in an inconsistent or invalid power state.

  9F, {4, 12 c, fffffa80196707c0, fffff880009ec810} error checking

  Parameter 1 of the bugcheck is 4 , which indicates that the transition of power over waiting to synchronize with the Pnp subsystem.

  The 2nd setting is 12 c , which indicates that it is exceeded for a total of 12 seconds.

  By default, the crash dump is failing UsbHub3.sys who is the pilot of HUB-USB3 (System driver and not the true cause, and is due to the fault by something else).

  If we look further into the dump:

  ERROR: Module load completed but symbols could not be loaded for btmhsf.sys

  FAILURE_BUCKET_ID: 0x9F_4_btmhsf_IMAGE_UsbHub3.sys

  Implicit thread is now fffffa80 196707 c 0

  ^^ If we run one! thread on the address fffffa80 196707 c 0:

  Child-SP RetAddr: Args to child: call Site
  fffff880 '20b42f20 fffff801' 890bb7cb: fffffa80'00000001 00000000'00000000 00000000'00000003 00000000'00000000: nt! KiSwapContext + 0 x 76
  fffff880 '20b 43060 fffff801' 890ba60f: fffffa80'18b23ef8 fffff880 '0115a 178 00000000 00000000' fffff880' 0622a 202: nt! KiCommitThreadWait + 0x23b
  fffff880'20 b 43120 fffff880'06114700: fffffa80 '16115fd8 fffff880' 00000001 00000000' 00000000 00000000'00000000: nt! KeWaitForSingleObject + 0x1cf
  "fffff880 '20b431b0 fffff880' 06117ef0: 00000000 ' 00000018 fffff880 ' 0622a2f8 00000000'00000000 00000000'00000018: btmhsf+ 0 x 33700
  fffff880 '20b431f0 fffff880' 060fb1e4: fffffa80'17 has 00030 fffff880 '20b433b0 fffff880' 0622a2f8 00000000' 00000000: btmhsf+ 0x36ef0
  fffff880 '20b 43260 fffff880' 060e2b84: 0000057f 'e9eaddd8 00000000' 00000127 fffff880 '0622a2f8 fffff880' 0115 has 178: btmhsf+ 0x1a1e4
  fffff880 '20b432b0 fffff880' 060e2cce: 00000000'00000008 fffff880 '20b 43370 00000000'00000008 fffff880' 20b 43378: btmhsf+ 0x1b84
  fffff880 '20b432e0 fffff880' 0114ecb0: fffffa80'16153860 00000000 00000000' fffff8a0 '04c3a748 fffff801' 89403cfe: btmhsf+ 0x1cce
  "fffff880 '20b 43310 fffff880' 010e881d: 00000000 ' 00000127 fffff880 ' 20b433b0 00000000'00000119 fffffa80'16153860: Wdf01000! FxPkgPnp::PnpEventSurpriseRemoveIoStarted + 0x2c
  "fffff880 '20b 43340 fffff880' 010e9032: fffffa80 ' 16153980 fffffa80' 16153988 fffffa80 ' 16153860 fffff880 ' 20b434c0: Wdf01000! FxPkgPnp::PnpEnterNewState + 0x1a1
  "fffff880 '20b433e0 fffff880' 010e8cdd: 00000000 ' 00000000 fffff880 ' 20b434c0 fffffa80 ' 16153970 fffffa80' 16153860: Wdf01000! FxPkgPnp::PnpProcessEventInner + 0 x 122
  fffff880'20 b 43450 fffff880'0114 701 d: 00000000 00000000' fffffa80 '16153860 fffff880' 00000000 00000000 00000000': Wdf01000! FxPkgPnp::PnpProcessEvent + 0x18d
  fffff880 '20b434f0 fffff880' 010d1ecf: fffffa80'16141 b 30 fffff880 '20b 43570 00000000 00000000' fffffa80' 1615d1d0: Wdf01000! FxPkgFdo::_PnpSurpriseRemoval + 0 x 25
  fffff880 '20b 43520 fffff880' 010c99da: fffffa80'197 b 9010 fffffa80 '197b 9010 fffffa80' 197b 9010 00000000 00000000': Wdf01000! FxPkgPnp::Dispatch + 0x18f
  "fffff880 '20b 43580 fffff880' 010c9aa6: fffffa80' 197b 9010 00000000'00000005 fffffa80 ' 161531 c 0 fffff880 ' 062fca20: Wdf01000! FxDevice::Dispatch + 0x19a
  fffff880 '20b435c0 fffff880' 062e3cbe: fffffa80 '197b 9010 00000000 00000005' fffffa80' 1615e190 00000000' 00000000: Wdf01000! FxDevice::DispatchWithLock + 0xa6
  fffff880 '20b 43600 fffff880' 062e3484: fffffa80 '197b 9010 00000000 00000000' fffffa80' 1615e190 00000000' 00000000: bthport! BthDefaultPnpHandler + 0x2a
  fffff880 '20b 43630 fffff880' 062e2cc1: fffffa80 ' 1615e190 fffff880 '062fca17 fffffa80' 1615e190 fffffa80 ' 197b 9010: bthport! BthHandleSurpriseRemoval + 0xc4
  fffff880 '20b436b0 fffff880' 062e2b04: fffffa80' 197b 9010 00000000'00000701 fffff880 '062fca20 fffff880' 20b 43800: bthport! BthHandlePnp + 0x16d
  fffff880 '20b 43700 fffff801' 8940a8f7: fffffa80 '1615e040 00000000' c00000bb 00000000 00000000' fffff880' 00a 82180: bthport! BthDispatchPnp + 0 x 68
  "fffff880'20 b 43750 89526 fffff801 39 d: 00000000 ' 00000017 fffff880 ' 20b 43819 fffffa80 ' 16137710 fffffa80' 16137060: nt! IopSynchronousCall + 0xc7
  fffff880 '20b437c0 fffff801' 895265e6: fffff8a0 ' 04069710 00000000'00000308 fffffa80' 16137060 00000000 00000000': nt! IopRemoveDevice + 0xd9
  fffff880'20 b 43880 fffff801'89526501: fffffa80'16137710 00000000 00000000' fffff8a0 '0c432a01 fffff880' 20b 43930: nt! PnpSurpriseRemoveLockedDeviceNode + 0xaa
  fffff880'20b438d0 fffff801'89526468: fffff8a0 00000000'00000000 00000000'00000000 ' 0c432a70 fffffa80'16137710: nt! PnpDeleteLockedDeviceNode + 0x5d
  fffff880 '20b 43910 fffff801' 89525bcb: 00000000 00000000' fffff880 '20b43a70 fffff8a0' 0b89e6f0 00000000'00000005: nt! PnpDeleteLockedDeviceNodes + 0 x 98
  fffff880 '20b 43970 fffff801' 893b52e5: fffff880'20b43b88 00000000 00000000' fffff8a0 ' 05764100 fffff8a0' 00000000: nt! PnpProcessQueryRemoveAndEject + 0x2c3
  fffff880'20b43ae0 fffff801'89418346: fffff8a0'04069710 00000000'00000000 00000000'00000001 00000000'00000000: nt! PnpProcessTargetDeviceEvent + 0x9d
  "fffff880 '20b43b20 fffff801' 890b62a1: fffffa80 ' 196707 c 0 fffff8a0 ' 0b89e6f0 fffff801 ' 8941805 c fffffa80' 16748130: nt! PnpDeviceEventWorker + 0x2ea
  "fffff880 '20b43b80 fffff801' 8904afd9: fffffa80 ' 00180000 00000000 00000080' fffff801 ' b 890, 6160 fffffa80 196707 c 0: nt! ExpWorkerThread + 0 x 142
  fffff880 '20b43c10 fffff801' 890ff7e6: fffff880 ' 00a 82180 fffffa80 ' 196707 c 0 fffffa80 ' 06741b 00 fffffa80' 06765940: nt! PspSystemThreadStartup + 0 x 59
  fffff880'20b43c60 00000000' 00000000: fffff880 '20b 44000 fffff880' 20b3e000 00000000'00000000 00000000'00000000: nt! KiStartSystemThread + 0x16

  We can see the various routine calls BTHUSB Device bthport.sys (Bus Bluetooth driver) who then finally enter various before btmhsf.sys some error checking.

  btmhsf.sys is the Intel Proset Bluetooth HighSpeed filter driver and probably the culprit here. Update this driver ASAP - http://downloadcenter.intel.com/default.aspx?iid=gg_support-EN_01+home_downloadctr
  or uninstall it if you do not plan to use BlueTooth.

  ---------------------------------------------------------------------

  If after doing the above, you are still blocked, remove and replace AVG with built-in Windows Defender from Windows 8 for temporary troubleshooting purposes:

  -AVG removal tool http://www.Avg.com/us-en/utilities

  In addition, to answer your question as to why the MEMORY. DPM is so important because it's a dump of memory rather than a small kernel. Kernel memory dumps contain all the kernel memory was working with and that was in use at the time of the accident, that is why it is larger and provides much more information.

  Kind regards

  Patrick

• BSOD, BCCode f9, caused by ntoskrnl.exe, could you please help me with this?

  I get the BSOD with f9 code and I do not understand what is? Could you please advice what may cause this? I'm not sure,
  It happen when I stop or restart (15 minutes with him saying to stop) followed by BSOD (pilot State power failure).
  Once I'm back I can see that Windows has recovered from unexpected shutdown down. Using BlueScreenView tells me that ntoskrnl.exe is the cause.
  I was wondering if it has something to do with the USB Ports, because it won't work as a plug-and-Play (need to reboot USB is plugged).

  I reinstall all the USB drivers.

  My system:
  ASUS Z170A
  nVIDIA GTX 980ti

  850 M2 OF EVO 250 GB SSD

  Intel Core i7 - 4700 k
  32 GB of RAM (4 sticks 8 GB)
  Windows 7 64 bit

  All up to date.

  ==================================================
  Name of the file: ntoskrnl.exe
  Address of stack: ntoskrnl.exe + e23f0
  Address: Fffff800'0325e000
  Address: Fffff800'03844000
  Size: 0x005e6000
  Time stamp: 0x5708972e
  Time string: 09/04/2016 13:46:22
  Product name: Microsoft® Windows® Operating System
  File description: NT kernel & system
  File version: 6.1.7601.23418 (win7sp1_ldr.160408 - 2045)
  Company: Microsoft Corporation
  Full path: C:\Windows\system32\ntoskrnl.exe
  ==================================================
  ==================================================
  Dump file: 081316-13447 - 01.dmp
  Crash time: 13/08/2016-12:46:05
  Bug Check String: DRIVER_POWER_STATE_FAILURE
  Bug check code: 0x0000009f
  Parameter 1: 00000000'00000003
  Parameter 2: fffffa80'1a0f1060
  Parameter 3: fffff800'052373 d 8
  Parameter 4: fffffa80'1f739c60
  Caused by the driver: ntoskrnl.exe
  Caused by the address: ntoskrnl.exe + 6f400
  File description: NT kernel & system
  Product name: Microsoft® Windows® Operating System
  Company: Microsoft Corporation
  File version: 6.1.7601.23418 (win7sp1_ldr.160408 - 2045)
  CPU: x 64
  Plant address: ntoskrnl.exe + 6f400
  Stack address 1:
  The stack address 2:
  Address 3 the battery:
  Computer name:
  Full path: C:\Windows\Minidump\081316-13447-01.dmp
  Number of processors: 8
  Main version: 15
  Minor Version: 7601
  Size of the dump file: 1 250 528
  Dump of file time: 13/08/2016-12:47
  ==================================================

  Hello

  There is a possibility that there is a problem with a driver on your PC. Here are a few things to try:
  • If you know which driver is causing the problem, update.
  • Make sure your hardware drivers are updated.

  Please keep us updated.

  Kind regards.

• Caused by ntoskrnl.exe BSOD

  I get a lot of recent BSOD caused by + 59869 ntoskrnl.exe.  Doesanyone knows how to solve this problem?

  This is the dump: https://onedrive.live.com/redir?resid=A890DBFB04708DE%21107

  Hi Drew,

  Welcome to the Microsoft Community Forum.

  Based on my research by analyzing the time Mini dump file dump file gave the following result.

  PRIMAX Gaming Mouse

  STACK_COMMAND: kb

  FOLLOWUP_IP:

  NMgamingms + 1cbb

  fffff880'08512cbb

  SYMBOL_STACK_INDEX: 5

  SYMBOL_NAME: NMgamingms + 1cbb

  FOLLOWUP_NAME: MachineOwner

  MODULE_NAME: NMgamingms

  Nom_image: NMgamingms.sys

  DEBUG_FLR_IMAGE_TIMESTAMP: 4a6976ec

  FAILURE_BUCKET_ID: X64_0x139_NMgamingms + 1cbb

  BUCKET_ID: X64_0x139_NMgamingms + 1cbb

  Follow-up: MachineOwner

  This file belongs to product Primax Gaming Mouse and was developed by the Primax Ltdcompany. This file description optical mouse USB Primax driver.

  I suggest updating the driver for your mouse in Device Manager and check if you are able to solve the problem.

  1. Press "Windows + R".
  2. Type devmgmt.msc
  3. Go with the mouse, right-click on it and click Update driver software

  I hope this helps. Write to us for assistance.

• BSOD caused by ntoskrnl.exe (and maybe hal.exe?)

  Hi all

  I don't have much experience in debugging BSOD minidumps so I turn for help. Attached all my files dump in time past. All caused my computer to turn off instantly, of course, sometimes it turns even off exactly when windows loads. From the little I know, I think maybe it's a hardware failure (0 x 124), but I'm not sure. Any help would be greatly appreciated.

  Here is the download link: MiniDump

  Thank you very much for any help!

  Hello

  References to Vista also apply to Windows 7.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded: run DriverView - set the VIEW to hide
  Microsoft drivers - update those without drain in their names. (Also update BIOS and)
  drivers chipset on the site of the constructor/the system motherboard.)

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods
  above is preferred so that the latest drivers from the manufacturer of system and device manufacturers are
  found)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, this leaves ONE of Windows updates, but it will not install the drivers who will be generally
  be older and cause problems. If updates offers a new driver and then HIDE it (right click on it)
  and then go look for new ones manually if you wish.

  How to stop Windows 7 automatically install drivers
  http://support.Microsoft.com/kb/2500967

  ==========================================

  Tests of memory intercept all errors such as memory do not match (possible even for sticks
  seemingly identical) and when the faster memory is placed in system behind the slower memory.
  So it is best to Exchange also sticks in and out to check for those, even if all the tests of memory do not
  show a problem.

  To test the RAM here control - run 4 + hours or so.<-- best="">
  www.memtest.org

  For the Windows Memory Diagnostic tool.

  Start - type in the search-> memory box - find top - click - right Memory Diagnostics tool
  RUN AS ADMIN follow the instructions

  How to run the diagnostic tool memory in Windows 7
  http://www.SevenForums.com/tutorials/715-memory-diagnostics-tool.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• DRIVER_POWER_STATE_FAILURE caused by ntoskrnl.exe

  Dear all,

  I got the BSOD recently with my Windows 7 Home premium 64-bit in the standby/hibernation with "DRIVER_POWER_STATE_FAILURE" of the memory minidump file bug_check_string that I analyzed with utility BlueScreenView.

  I downloaded the minidump files in my SkyDrive to the following:

  http://CID-cb84f720a8912916.Office-DF.live.com/self.aspx/.public/minidump.zip

  Appreciate the assistance to find out what drivers are causing this issue.

  Thank you!

  Here is a part of the analysis of WinDbg (Windows Debugger) from your other laptop error checking:

  FAILURE_BUCKET_ID: X64_0x9F_3_athrx_IMAGE_pci.sys

  BUCKET_ID: X64_0x9F_3_athrx_IMAGE_pci.sys

  That would indicate a problem with the athrx.sys which is the driver of the wireless adapter.

  However, since you seem to have install the program (driver = connctfy.sys) Connectify, Connectify program is perhaps the question, as in the following thread:

  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/d7815afd-7072-46FF-BDF6-73c63d10cfd1

  So try to update the wireless driver and if it does not help uninstall Connectify.

  I posted some info on playing the minidump files in the following thread:

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/e1c01b9c-89ac-4EEE-b60a-6a5e0eb4d641/

  Watching the minidump with a debugger files will often display the problematic driver, but sometimes, as what may be the case with your other laptops, the cause is not always obvious.

• Windows 8 high disk caused by Tiworker.exe

  Do I need this, what is it? Can I remove it safely?

  Hello

  I suggest you run online virus scan to check whether the problem is with the virus.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Hi Vijay,

  Thanks for your suggestion, I use AVAST! Internet Security Pro (PAID) & we found 0 problems, my thought is that I inadvertently deleted the necessary files of the WinSxS folder that was stupid on my part because I know not to mess with system files not knowing what their goal is, I'm sure I'm not the only one to do this but perhaps the only one to admit & not blame it on the BONE, LOL. Anyway I had no other choice but to re - install a clean drive, so I took the opportunity to install W10 & I'm so glad I did.

  I think it's far the best OS of Microsoft to date, as many user-friendly features & navigate with ease, too many changes, I like the list, but I do especially like speed it load, same as any Android phone, & task view functionality when you are working with multiple windows, I added a sidebar with my favorite gadgets that is always on top so other windows dock to it.

• blue screen, hp, win7, Probabily caused by: ntoskrnl.exe

  dump file is here, https://www.dropbox.com/sh/lkb70s6iomnzour/tMSltYbo68, anyone please help? Thank you very much.

  take the mem test
  http://Windows.Microsoft.com/en-in/Windows7/diagnosing-memory-problems-on-your-computer

• Portege 3440: ntoskrnl.exe file needs to be replaced - how to start without external hard drive

  Hello

  My 3440 has developed a problem, I think the boot.ini file corruption that it requests to the file ntoskrnl.exe replaced at startup. The problem is that I don't have an external drive to boot from. When I press F2 it gives me a list of devices, that which no no it starts from. I don't have the external CD drive for this, and it won't have a USB floppy drive.

  It is impossible for me to solve this problem without the external port replicator or a cd player?

  Thanks in advance

  Pete

  Hello

  Unfortunately, without the access on the Windows CD you will not be able to fix it.

  The ntoskrnl.exe file is placed on the original Windows CD in the i386 folder.
  You could start at the beginning of the CD to make the repair console by pressing R
  In the repair console, you can use this command:

  Expand D:\i386\ntoskrnl.ex_C:\windows\ntoskrnl.exe
  (D is the CD drive)

  But as said above seems that you will need the CD player

  But wait if the i386 folder has been installed on your HARD drive you could expand the ntoskrnl.exe in this folder to C:\windows\

• Driver power state failure ntoskrnl.exe when shutting down

  Hi, when I shut down my computer, I get the BSOD, DRIVER_POWER_STATE_FAILURE caused by ntoskrnl.exe. Here are my files dump https://dl.dropboxusercontent.com/u/5085743/dump.zip

  Thank you very much!

  Gameboy90

  In addition to suggestions of Patricks I would also update the driver associated with USB driver from VMware, Inc. VMware.  Yours is 4 years old and cant work properly to win 8.

  I would like to re - install the latest driver available.

• Bluescreens ntoskrnl.exe dkgkrnl.sys

  Hi, I have a problem with a new PC (Vista Home Premium 64-bit), giving many bluescreens. There is no reason of their past, they are random. I have updated all drivers and unplugged everything that is not essential (remote control Receivers etc.).
  Using the program "that crashed" I've identified ntoskrnl.exe and dkgkrnl.sys as the most frequent culprits.

  I have run the System File Checker. It reports
  "The audit complete 62%.
  Resource protection Windows found corrupt files but was unable to remedy.
  Details included in... CBS.log.

  How to interpret the log? and solve this problem?
  I did stick the contents of the newspaper because there are a lot of lines!

  Mike

  Hello

  SFC bombed 62% if you have to drive or other hardware issues well OS and software
  could cause or be part of the issue. Run CheckDisk and then try to SFC. See Troubleshooting below
  and methods in the next message to use when you reach the part of the resolution of the generic driver update problems.
  Then you can return to the resolution of the problems after the driver updates if necessary.

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  To check the drive after checkdisk above select the hard drive maker in this list and use
  their diagnosis.

  By manufacturer diagnostic utilities
  http://www.techsupportforum.com/hardware-support/hard-drive-support/302602-hard-drive-diagnostic-utilities.html
  SpeedFan
  http://www.almico.com/sfdownload.php

  HD Tune
  http://www.hdtune.com/

  ----------------------------------------------

  Think hard drive problems, drivers, security/antivirus/antispyware products and there are other possible causes.

  My convenience store generic bluescreen - the journal of the SFC, error of the utility Nirsoft below and any extra Codes
  info from the event viewer should help. Thanks to post Error Codes and anything that could help you help.

  Look in the Event Viewer to see if something is reported on those.

  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Ntoskrnl.exe BSOD at random

  I get a BSOD caused by ntoskrnl.exe or ntfs.sys, with a lot of different bugs 0x0f and 0x0A 0x01E. I used WhoCrashed to help me find what it was, but in no avai.

  Here at random, take a few minutes to a few hours.
  Here are the logs of WhoCrashed

  Thursday, November 10, 2011 2:48:45 AM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\110911-26130-01.dmp
  This was probably caused by the following module: ntfs.sys (Ntfs + 0x213D8)
  Verification of error code: 0 x 24 (0xFFFFF88009D8C348, 0xFFFFF88009D8BBB0, 0x1904FB, 0xFFFFF80002EE2EEA)
  Error: NTFS_FILE_SYSTEM
  file path: C:\Windows\system32\drivers\ntfs.sys
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT file system driver
  Bug control description: This indicates there is a problem in the NTFS file system.
  The accident took place in a standard Microsoft module. Your system configuration is perhaps incorrect. Maybe this problem is caused by another driver on your system which cannot be identified at this time.

  Thursday, November 10, 2011 2:48:45 AM GMT crashed your computer
  crash dump file: C:\Windows\memory.dmp
  This was probably caused by the following module: ntfs.sys (Ntfs + 0x213D8)
  Verification of error code: 0 x 24 (0xFFFFF88009D8C348, 0xFFFFF88009D8BBB0, 0x1904FB, 0xFFFFF80002EE2EEA)
  Error: NTFS_FILE_SYSTEM
  file path: C:\Windows\system32\drivers\ntfs.sys
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT file system driver
  Bug control description: This indicates there is a problem in the NTFS file system.
  The accident took place in a standard Microsoft module. Your system configuration is perhaps incorrect. Maybe this problem is caused by another driver on your system which cannot be identified at this time.

  Thursday, November 10, 2011 2:18:09 AM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\110911-19515-01.dmp
  This was probably caused by the following module: ntfs.sys (Ntfs + 0x212A3)
  Verification of error code: 0 x 24 (0xFFFFF88008DD4708, 0xFFFFF88008DD3F70, 0 x 190477, 0xFFFFF80002EA5C84)
  Error: NTFS_FILE_SYSTEM
  file path: C:\Windows\system32\drivers\ntfs.sys
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT file system driver
  Bug control description: This indicates there is a problem in the NTFS file system.
  The accident took place in a standard Microsoft module. Your system configuration is perhaps incorrect. Maybe this problem is caused by another driver on your system which cannot be identified at this time.

  Thursday, November 10, 2011 2:05:19 AM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\110911-22682-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0 x 70590)
  Bugcheck code: 0x1E (0x0, 0x0, 0x0 0 x 0)
  Error: "KMODE_EXCEPTION_NOT_HANDLED"
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that a kernel-mode program generated an exception which did not catch the error handler.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Wednesday, November 9, 2011 11:39:15 PM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\110911-20638-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0x705C0)
  Bugcheck code: 0xA (0xFFFFF880029ED988, 0xFFFFF80002D205F1, 0x2, 0x0)
  Error: IRQL_NOT_LESS_OR_EQUAL
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that Microsoft Windows or a driver in mode accessed kernel memory paged at DISPATCH_LEVEL level or above.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Thursday, October 27, 2011 7:49:38 AM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\110911-25162-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0x705C0)
  Bugcheck code: 0xD1 (0xFFFFF8808327B1DA, 0xFFFFF880042A41EA, 0x2, 0 x 1)
  Error: DRIVER_IRQL_NOT_LESS_OR_EQUAL
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that a kernel-mode driver attempted to access pageable memory with a high IRQL.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Thursday, October 27, 2011 3:11:46 AM GMT crashed your computer
  crash dump file: C:\Windows\Minidump\102611-21106-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0 x 70600)
  Bugcheck code: 0x3B (0xC0000005, 0x1, 0x0, 0xFFFFF88009B94300)
  Error: SYSTEM_SERVICE_EXCEPTION
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Let me know if I need to download the DPM

  Hello

  Doubt that its windows for millions would have the same questions.

  If you think that your Windows installation disc is damaged, try these as a test.

  This will give you a method to make and install from another disk as a test.

  Windows 7 Enterprise - 90 day trial
  http://TechNet.Microsoft.com/en-us/evalcenter/cc442495.aspx

  They will help make you the ERD that are bootable.

  If you need to repair disks - these help repair Windows not re-install.
  Often an ERD will help you when the recovery disk does not work.

  Download Windows 7 system recovery discs - charge now $9.75 for ISO
  images to make the discs.
  http://NeoSmart.net/blog/2009/Windows-7-system-repair-discs/

  How to create a Windows 7 - free system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  ========================================

  These make it bootable Linux disks with many public services:

  Hiren Boot CD
  http://www.hirensbootcd.org/

  Rescue Kit Trinity
  http://trinityhome.org/home/index.php?wpid=1&front_id=12

  System Rescue CD
  http://www.SysRescCd.org/Main_Page

  Knoppix
  http://www.Knoppix.NET/

  Scan a Windows PC for viruses from a Ubuntu Live CD
  http://www.howtogeek.com/HOWTO/14434/scan-a-Windows-PC-for-viruses-from-a-Ubuntu-Live-CD/

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Random BSOD and I do not know why.__Unable to load the image \SystemRoot\system32\ntoskrnl.exe, 0n2 error Win32

  I don't know why this is happening, but I'm getting random BSOD now and then. I tried to point out my system to see if it generates a BSOD, but multitasking 3d and photoshop programs and what's not stress, then when I least expect, BANG! BSOD.
  The last of them, that I had now was in the middle of the night with almost no programs running. The system had worked for some time (one or two days), but nothing was he pointing out at the same time.

  What I think happened was: our microwave shorted out and caused a fuse to blow. But it was on another grid in our House (I hope I make myself clear, because I'm not used to talk about stuff like this in English!) so it should not affect my computer. But at the same time my microwave said "Thank you for everything!" my computer would BSOD. The thing is that my modem, my switch, my router and my NAS is connected to the electric network and my short circuted of switch. And my computer is connected to the switch cable.
  This effect possible that excess tension (or something) has short circuted my switch and 'jumped' power to the switch and on the cable and sending there is a shock to my computer? Or am I just paranoid? Laughing out loud

  I know that the controllers are pushed to the limit of the memory and therefor tolerate very little when it comes to electricity. I ran MemTest4.00 14 passes but I came with nothing. But memtest that tests memory, not the controllers, right? I am watching a fried motherboard?

  I did a windb, but I don't understand what he says. Could someone please translate this for me and give me your opinion?
  In addition, when you run windb, it's tell me am I wrong symbols. -What this means, and where can I get the symbols he wants? And what symbols?

  Microsoft (R) Windows debug 6.12.0002.633 AMD64 Version
  Copyright (c) Microsoft Corporation. All rights reserved.

  Loading dump file [C:\Windows\Minidump\Mini042910-01.dmp]
  The mini kernel dump file: only registers and the trace of the stack are available

  Symbol search path is: * invalid *.
  ****************************************************************************
  * Loading of the symbol may be unreliable without a symbol search path.           *
  * Use .symfix to get the debugger to choose a symbol path.                   *
  * After adjusting your path to symbols, use .reload to refresh the locations of symbols. *
  ****************************************************************************
  Executable search path is:
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntoskrnl.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntoskrnl.exe
  ERROR: Module load completed but symbols can be loaded for ntoskrnl.exe
  Windows Server 2008/Windows Vista Kernel Version 6002 (Service Pack2) MP (4 procs) free x 64
  Product: WinNt, suite: TerminalServer SingleUserTS
  Computer name:
  Kernel base = 0xfffff800 '02c4c000 PsLoadedModuleList = 0xfffff800' 02e10dd0
  The debugging session: 23:43:16.368 Thursday, April 29, 2010 (UTC + 02:00)
  System Uptime: 3 days 5:21:50.657
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntoskrnl.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntoskrnl.exe
  ERROR: Module load completed but symbols can be loaded for ntoskrnl.exe
  Loading the kernel symbols
  ...............................................................
  ................................................................
  ................................................
  Loading user symbols
  Loading unloaded module list
  ......
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  Use! analyze - v to obtain detailed debugging information.

  Bugcheck A, {fffffa7fffffffea, 2, 0, fffff80002c5a95c}

  The kernel symbols are FALSE. Correct symbols to do the analysis.

  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  Probably caused by: ntoskrnl.exe (nt + e95c)

  Follow-up: MachineOwner
  ---------

  0: kd >! analyze - v
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  IRQL_NOT_LESS_OR_EQUAL (a)
  An attempt was made to access an address pageable (or completely invalid) to a
  application interrupt level (IRQL) that is too high.  It is usually
  caused by drivers using a wrong address.
  If a kernel debugger is available, download the stack trace.
  Arguments:
  Arg1: fffffa7fffffffea, memory referenced
  Arg2: 0000000000000002, IRQL
  Arg3: 0000000000000000, bit field:
  bit 0: value 0 = read operation, 1 = write operation
  bit 3: value 0 = not an enforcement operation, 1 = performance operation (only on chips that support this level of State)
  Arg4: fffff80002c5a95c, address memory

  Debugging information:
  ------------------

  The kernel symbols are FALSE. Correct symbols to do the analysis.

  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************

  ADDITIONAL_DEBUG_TEXT:
  Use '! findthebuild' command to search for the generation of target information.
  If the build information is available, run '! findthebuild s; .reload ' to set the symbol path and of loading symbols.

  MODULE_NAME: nt

  FAULTING_MODULE: fffff80002c4c000 nt

  DEBUG_FLR_IMAGE_TIMESTAMP: 4b7d238f

  READ_ADDRESS: could not get nt! MmSpecialPoolStart
  Unable to get nt! MmSpecialPoolEnd
  Unable to get nt! MmPoolCodeStart
  Unable to get nt! MmPoolCodeEnd
  fffffa7fffffffea

  CURRENT_IRQL: 0

  FAULTING_IP:
  NT + e95c
  fffff800'02c5a95c?              ???

  CUSTOMER_CRASH_COUNT: 1

  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

  BUGCHECK_STR: 0XA

  LAST_CONTROL_TRANSFER: from fffff80002ca626e to fffff80002ca64d0

  STACK_TEXT:
  fffffa60 '01bde688 fffff800' 02ca626e: 00000000' 0000000 a fffffa7f ' ffffffea 00000000'00000002 00000000'00000000: nt + 0x5a4d0
  fffffa60 '01bde690 00000000' 0000000-a: fffffa7f 'ffffffea 00000000'00000002 00000000'00000000 fffff800' 02c5a95c: nt + 0x5a26e
  fffffa60 '01bde698 fffffa7f' ffffffea: 00000000'00000002 00000000'00000000 fffff800 '02c5a95c fffffa60' 04dbf8b0: 0xa
  fffffa60 '01bde6a0 00000000' 00000002: 00000000 00000000' fffff800 '02c5a95c fffffa60' 04dbf8b0 00000000' 00000000: 0xfffffa7f'ffffffea
  fffffa60'01bde6a8 00000000' 00000000: fffff800 '02c5a95c fffffa60' 04dbf8b0 00000000'00000000 00000000'00000000: 0 x 2

  STACK_COMMAND: .bugcheck; Ko

  FOLLOWUP_IP:
  NT + e95c
  fffff800'02c5a95c?              ???

  SYMBOL_NAME: nt + e95c

  FOLLOWUP_NAME: MachineOwner

  Nom_image: ntoskrnl.exe

  BUCKET_ID: WRONG_SYMBOLS

  Follow-up: MachineOwner
  ---------

  I'm grateful for any help I can get in that case.

  My system is: AMD 9950BE CPU, motherboard ASUS Crosshair II Formula, 4 x 2 giga OCZ 1066 mhz memory, Vista Ultimate 64 bit, ASUS 295GTX GPU

  Postal salvation,

  I think you're in luck. It chances are you are one of those rare cases where the BSOD may not be hardware related. In addition, it is actually pretty rare to have so many errors after a sfc... Wow. I think that alone has helped reduce the risk of an another BSOD and was good insurance against other problems.

  Do you have a chance to check the hard drive? Now, I would like to check the hard drive to see if there may be potential damage to the hard drive as well to help explain this number of errors (return to the material again).

  Here's how to new:

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  I think that advice on the anti-virus scanning are also actually still relevant today. I have a scan of one of the two groups below as soon as you can and let us know the result if you can.

  virus/malware programs:

  Symantec:

  Works in Safe Mode and free:

  _ http://security.symantec.com/sscv6/WelcomePage.asp

  Trend Micro

  _ http://housecall.trendmicro.com/

  Ad-ware/spyware:

  Ad-aware

  http://www.lavasoftusa.com/

  Spybot Search and Destroy

  http://www.safer-networking.org/

  * It is an excellent versatile tool as it will both spyware and malware and has also a small footprint.

  See you soon,.

  Steve <> Microsoft Partner