Windows XP backup contains a media error

Similar Questions

• Windows 7 backup fails with the error code: 0x8078012D

  I ran several backups on my external hard drive without problem, but I am now constantly a backup failure with an error code of 0x8078012D.

  How can I fix?

  Hi Helen,

  I suggest to rerun the command chkdsk (check disk) and let us know if there are bad sectors found/fixed.

  You can also see the following article for more information about the disk check:

  Check a drive for errors

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

   

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Also, make sure that the Volume Shadow Copy service is running.

  Follow the steps below:

  a. click Start.

  b. type Services in start search.

  (c) in the search for Services Windows shadow copy volume and the Windows backup from the list.

  d. right-click on the Service.

  e. click Properties.

  f. Select the Startup Type to Manual.

  g. click OK.

  h. now, repeat the same for the service Windows backup.

  Let us know the results.

• Windows 7 backup system Image - 0x8078012D error Code - fails to complete system image backup?

  I seem to have a problem with the Windows backup when a scheduled backup image on a hard drive external fails to finish, although she worked successfully before many times.  Backup Windows reports an error code of 0x8078012D.

  I ran the tool of error checking on the external hard drive with running repair options, but no problem discovered.  The external disk drive seems ok because I use a Norton program to back up data on the same drive with no problems.  Also Windows backup will happily make a 'non-system image' backup on the external drive.

  But it is not an image of the system stand alone, or as an add on the a normal backup.

  Any advice?

  Thank you
  David

  After many tests on the solutions listed here, I found a way to fix my problem. I had continually failure is to say the system could not create a snapshot or that my drive has been a failure. It seems, with Windows 7, you must configure options that are not obvious to the users.

  1. go to control panel/system/System Protection and select your C: drive.

  2. Select "set up" and make sure "Restore system settings and previous versions of files" is on.

  3. the Max use value at least 2%

  4. apply

  5. Select your key USB you will use for backup and configure it again to the protection and the whole file size of at least 18%.

  6. apply

  7. in the control panel go to administrative tools, open Services.

  8 scroll down until Windows backup and make sure it is set to manual and not started.

  9. highlight Volume Shadow and make sure it is also set to manual and not started.

  10 10 aller go to control panel, select backup and restore.

  11. click on "Change settings", and then select the drive you will support up to.

  12 run backup let the system do its thing and everything should work.

• Windows 7 backup won't start, error: error 0 x 80070422

  original title: backup does not start

  Error 0 x 80070422, no active device is associated.  The service runs.

  Windows 7 Ultimate 64.

  I ran into the same error. What has worked for me, is to go into 'msconfig' and under the general tab, make sure that there is a check mark in the box "load system services.  After a reboot my backup now works.

• Error message: windows\system32\difxapi32.dll isn't is either not designed to run on windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for

  Hello

  I keep getting error messages when I use the computer. It started two days after you download an update from Windows. A sample of the error is:

  C:\windows\system32\difxapi32.dll is not designed to run on windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support.

  I use a vista. I don't know how to solve this problem, many want to help.

  Thank you.

  Hi Colinthebrave:

  Start with this little tool to help get rid of the error, once your system is stable again and then try to run your updates again.

  Thank you for your message; Let us know how it goes.

  o

  o The System Restore tool

  If the problem you are experiencing started occurring recently, you can use the System Restore tool. Using this tool, you can restore the computer to an earlier point in time. The tool using System Restore may not necessarily help you determine the problem. When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  2. in the System Restore dialog box, click on choose another restore point and then click Next.

  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  4. click on finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Don
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error: _ "Sidebar.exe - bad image"__windows/system32/sfc.dll is not designed to run on windows or it contains and error. " Try to install the program by using the original installation media or contact your system administrator. __

  Help, please!
  I started my computer today and it came with this error:

  "sidebar.exe - incorrect image.
  Windows/System32/SFC.dll is not designed to run on windows or it contains and error. Try to install the program by using the original installation media or contact your system administrator.

  I click on OK, then he said:

  "Acrotray.exe - incorrect image.
  Windows/System32/SFC.dll is not designed to run on windows or it contains and error. Try to install the program by using the original installation media or contact your system administrator.

  I click OK and then it says:

  "hpqtra08.exe - incorrect image.
  Windows/System32/SFC.dll is not designed to run on windows or it contains and error. Try to install the program by using the original installation media or contact your system administrator.

  Also I got an error report saying that windows sidebar stopped working.

  My computer is VERY slow in all the commands I give.
  I also tried to run the sfc (System File Checker command) and acts like he is going to run the program, but then just closed.

  Do you have an idea what is happening with my computer and what I can do to fix this?

  Thank you very much!

  Hi deacon829,

  You did changes to the computer before that happened?

  Step 1: Start the computer in safe mode and check if the problem persists, to do this, follow the steps below,

  Access the menu advanced startup options by turning on your computer and pressing the F8 key before Windows starts. In the advanced startup options select safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: If you try to install any application before this program, try to uninstall them.

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  If this solves the problem, you can deduct that the demand is probably corrupted, damaged or incompatible. You can check with the manufacturer of the program for more information.

  Step 3: System Restore: System Restore to put the computer's system files to an earlier point in time.

  Look for steps to restore of the system in the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  If the problem persists,

  Step 4: A scanner online for any threat and try to correct

  http://OneCare.live.com/site/en-us/Center/cleanup.htm

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Media Center product error ": \Windows\System32\Mpeg2Data.ax is not designed to run on Windows or it contains an error.

  Hello

  After you follow the instructions to repair a problem as indicated in the following thread, I now have a problem with Media Center

  https://answers.Microsoft.com/en-us/Office/Forum/office_2010-office_install/problem-with-grooveintlresourcedll/c12778e6-4822-4cac-ad22-6e39cd4a4180

  Media Center opens OK but after the start of a string of television, immediately it is running (and still running), it produces the following error

  ehexthost.exe - incorrect Image

  ---------------------------

  C:\Windows\System32\Mpeg2Data.AX is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support.

  I tried to remove Media Center via Add or remove programs, but the problems reoccurs. No one knows how to fix?

  As I said, this is a repair through the upgrade option (Win7 64 bit).

  I've sorted the DotNet question using the cleaning tool to remove all traces of the previous versions, then only the latest version. Other remedies proposed in the community forums has not worked.

• "c:\windows\system32\dbghelp.dll" "not designed to run on windows or it contains an error.

  Original title: c:\windows\system32\dbghelp.dll

  In the few weeks whenever I turn on my computer, try to save a document in Notepad or listen to music on windows media player, I get this error message "bad image" which appears again about 5 times in a row until it disappears eventually.

  "c:\windows\system32\dbghelp.dll" "not designed to run on windows or it contains an error" he cites that< a="" lot,="" i="" don't="" know="" how="" to="" stop="" this...="">

  Another question is, apparently, that my Security Center is turned off, but when I try to turn it on, nothing happens - no windows/web page opens. The two are related?

  How can I fix these problems?

  Hi Pyrcia,

  1. you remember to make changes to the computer before this problem?

  Step 1:

  You can try to run a SFC scan to check all corrupted files.

  You can read the following article to launch the SFC scan:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Step 2: You can check the status of the Security Center service.

  a. Click Start, type services.msc in the search bar and press ENTER.

  Note: If UAC (User Account Control) window is prompted for permission to continue, please click on continue.

  b. double-click the Security Center service and switch to the general tab.

  c. change the startup type to automatic, and then click on apply.

  d. Click Start, and then click OK.

  Step 3:

  You can also check out the following link and try to download the Microsoft Safety Scanner and perform a full scan on your computer.

  Microsoft safety scanner

  Note: When you perform the analysis, there are risks of data loss you can take a backup of important data before performing analysis.

  Hope this information is useful.

• C:\Windows\System32\wship6.dll is not designed to run on Windows or it contains an error.

  I can't open windows live mail and other programs that also many installers will not work for this reason.

  I get the following error:

  wlmail.exe - incorrect Image

  C:\Windows\System32\wship6.dll is not designed to run on
  Windows or it contains an error. Try to install the program using the
  the original installation media or contact your system administrator or
  the Publisher of the software to support

  I had to click OK 4 or 5 times to make it go away

  Many installers will not work because of this.

  System information:

  OS version: Microsoft Windows 7 Home Premium, Service Pack 1, 64-bit
  Processor: AMD A6 - 3400 M APU with graphics HD Radeon (TM), AMD64 family 18 model 1 Stepping 0
  Number of processors: 4
  RAM: Mb 5610
  Graphics card: AMD Radeon (TM) HD 6520 G, 512 MB
  Hard disks: C: Total - Mo 595354, Free - Mo 401604; Total D: - 14820 MB, free - 1647 MB; F: total - 99 MB, free - 89 MB; G: total - Mo 953867, Free - 877240 MB;
  Motherboard: Hewlett-Packard, 358B
  Antivirus: Norton Internet Security, updated and activated

  Here's what I did to remedy:

  I had to replace the \wship6.dll c:\windows\sysWOW64 file not the file c:\windows\system32\wship6.dll

  I had to start Windows Recovery Environment, load the command prompt and replace the file c:\windows\sysWOW64\wship6.dll to a system of work w7 (I used an iso oem and 7zip)

  ( 1 copy the file in a place should be on my boot drive (c :) in my case))

  2 . restart your computer , press and hold F8 as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you will need to start over; to do this, hold the Windows logon prompt appears, and then stop and restart your computer.

  3 . Select repair your computer and press enter.

  4 . Select the option for command line

  type 5 bcdedit | find "osdevice" (note that there is a space after bcdedit and | and also find) that will tell you what drive letter to use to access your startup drive (d: in my case)

  type 6 the drive letter followed by a: (d: in my case) and press enter , the guest must pass to < DriveLetter >: (in my case d:)

  type 7 copy < your place should be > wship6.dll windows\syswow64\wship.dll (replace < your place should be > with the full path to where you place the file) (note the space between the .dll and windows)

  If this does not work, you may need to replace syswow64 system32 in all the above instructions

• Can't mistake of playing Age Of Empires 3 on Windows 7 64-bit message - d3dx9_25.dll isn't is either not designed to run on Windows or it contains an error

  Original title: can not play Age Of Empires 3 on Windows 7 64 bit

  I recently downloaded aoe 3 games for windows program, see the list also useful with Windows 7.

  Download fine, as does the installation but I have a very big problem all I get when I try and run all the extensions of aoe 3 is the following error

  c:\windows\system32\d3dx9_25.dll is not designed to run on Windows or it contains an error. try to install the program by using the original installation media or contact your system administrator or the provider of software for support.

  The file in question is there I tried to delete it using the program dxwebsetup or one that comes with the download aoe3 however both reinstall the same file accurate return.

  I have try the .exe running in all sorts of compatibility mode as well as manually from the install in compatibility mode. all I get is the same error each time. I ran the esfile auditor and lists some invalid files, I guess it's because they are cracked to work without the cd files. I downloaded the game 3 times now.

  My drivers are all upward to date, research on the internet I can't find a lot of information, a lot of links goto the forums on agecommunity.com but they are no longer works.

  I am really stuck and would appreciate any help thanks

  Hi Mitsouki,

  This problem may occur if the Microsoft DirectX file that is mentioned in the error message is damaged or is not copied correctly.

  Step 1: You can follow the steps mentioned in the article below, which deals with a similar question

  Game error: "the file d3dx9_xx. DLL is not found.

  http://support.Microsoft.com/kb/910813

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• C:\windows\system32\mshtml.dll is not designed to run on Windows or it contains an error.

  original title: C:\windows\system32\mshtml.dll is not designed to run on Windows or it contains an error.  Try to install the program by using the original installation media or contact your system administrator or the provider of software for pension

  The battery died and when I restarted my computer I started having this error message last week whenever I start my computer. Explorer opens but doesn't load properly, not usable.  Service pack 2 is installed when the first available.
  C:\windows\system32\mshtml.dll is not designed to run on Windows or it contains an error.  Try to install the program by using the original installation media or contact your system administrator or the provider of software for support
  I tried MS fixit but nothing helped.  Need help.

  Chances are that you see the effects of ongoing hijackware infection!

  • My infected computer - what should I do now?
    https://forums.Malwarebytes.org/index.php?showtopic=9573
  • Help: I got hacked. Now what should I do?
    http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

• Cabinet.dll is not designed to run on Windows or it contains an error

  I just got a message arrived to the top when I am logged in and do not understand!  Bed C:\Windows\system32\Cabinet.dll is not designed to run on Windows or it contains an error.  Try to install the program by using the original installation media or contact your system administrator or the provider of software for support.  I also don't seem to be able to run a scan Mcafee!  Any help please.

  Original title: help please

  Hello

  Did you do any change on the computer before this problem?

  Try the following and see if it helps.

  
  Method 1:
  I suggest to start in safe mode with network and then try to run a full system scan and check if it helps.
  
  Step 1:
  Start your computer in safe mode: http://windows.microsoft.com/en-US/windows-vista/Start-your-computer-in-safe-mode
   
  Step 2:
  Microsoft Safety Scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again. The data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.
  
  Method 2:
  How to solve the problem by running the clean boot in Windows Vista: http://support.microsoft.com/kb/929135                                                                                                                       
  Note: once you have completed troubleshooting, perform the steps from step 7: to reset the computer as usual.
  
  Method 3:
  To run a SFC scan, follow the steps described in the following Microsoft article.
  How to use the System File Checker tool to troubleshoot missing or corrupted system files on Windows Vista: http://support.microsoft.com/kb/929833
  
   
  Note

  : Also make sure that you have disconnected all external devices except the keyboard and mouse.

• MSASCui.exe bad Image... C:\Program Files/Windows Defender/Mp.Rt.Mon.DLL is not designed to run on Windows or it contains an error.

  Original title : A major problem with Windows Defender... will not run :(

  When I go to run Windows Defender, I get this message: MSASCui.exe bad Image... C:\Program Files/Windows Defender/Mp.Rt.Mon.DLL is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support.  Then, after clicking OK, you get another small window saying "Windows Defender User Interface has stopped working... Search for an online solution and close the program (which does nothing) or close the program.    WHY?  McAfee scan says there is nothing wrong with the computer... There is something wrong. Impossible to get websites to find, or they are very slow.

  I have VISTA Home Basic edition, Emachine, bought 32 year THAT VISTA was released this January.

  That is to say 9 - seems to work better than 8 (which took awhile to do)

  SP2 is installed and I believe that most, if not all the updates are installed.

  Oh, and no matter what flash supported won't run... little is a nice way of saying. My flash player update. It is mess up until I had to update. :(

  Try the suggestion of Azam K.  If this help not to do the following:

  https://community.McAfee.com/message/208529

  McAfee should have disabled Windows Defender.  If not, or if you did turn back on, you must turn it off.  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Defender-on-or-off   Windows Defender cannot be uninstalled from the Vista OS, but can be disabled to avoid conflict with other programs.

  You will probably need to uninstall Flash and reinstall it: http://www.adobe.com/support/flashplayer/

  I don't really like to make a negative comment on an anti-malware program, but McAfee has a reputation for sometimes bogged down operating systems.  If your problem persists, you will need to uninstall McAfee (to include using the McAfee removal tool) and see if that has any impact on your computer problems.  If there is an improvement, you may consider trying another program BC

  http://www.AV-Comparatives.org/

  http://www.dslreports.com/Forum/r25776413-2011-anti-virus-poll

  Kind regards...

• Cannot open my Explorer error C:\Windows\system32\DWrite.dll if the other is not designed to run on Windows or it contains an error

  Original title: cannot open my explores

  Try to connect to the Solution Explorer, I get a message:

  "C:\Windows\system32\DWrite.dll is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support"

  Is this a virus?
  What is a corrupted dll?
  An easy way to fix it?

  Hi Ephisto,

  Please see the thread with a similar problem and fix possible:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/mmcbasedll-is-either-not-designed-to-run-on/2031a0f9-c3b0-4d67-B9F1-87c6d2ec54b4

  I hope this helps!

• Get the following message.c:\windows\system32\ddrawex.dll isn't is either not designed to run on windows or it contains an error

  My screen to count keeps blinking and I get the above message. I'm trying to update my activex announcement of directx, but nothing works. The activex was told that it was not recommended for my computer. What can I do? I was told to try to install the program again, but I don't know the original installation media. I don't know what to do and the flashing makes me crazy. Thanks, Chris150

  * original title - continues to Flash the screen of my computer and I get the following message.c:\windows\system32\ddrawex.dll is either not designed to run on windows or it contains an error. Try to install the prgram using the original installation media. *

  My screen to count keeps blinking and I get the above message. I'm trying to update my activex announcement of directx, but nothing works. The activex was told that it was not recommended for my computer. What can I do? I was told to try to install the program again, but I don't know the original installation media. I don't know what to do and the flashing makes me crazy. Thanks, Chris150

  Hey chris150

  on the link below, there are a few different methods to try to see one that works for your problem

  see if one of them will help you

  http://pcsupport.about.com/od/findbyerrormessage/a/ddrawes-DLL-not-found-missing-error.htm

  Walter, the time zone traveller