Wireless Chipset in Tecra M10 - 1CH

Similar Questions

• No Wireless N on Tecra M10 with Intel Wifi Link 5100agn a XP Pro

  Hello

  I can not connect mode n to my wireless n router. There's always going to G.
  The driver that I use is 12.4.0.21 4.3.2009.

  802.11n mode is enabled, everything is set by default.

  Without thread-mode is set to standard, a., b and g.
  I wonder why the n modus is not shown here. This is perhaps the reason why I can't use the n-modus?

  Thanks for any help

  Rolf

  Hello

  > Wireless mode is set to standard, a, b, and g.

  Do you want to say that these WiFi modes (A, B and G) are defined in the settings of your WLan card?
  If Yes, then this would be the reason why the M10 doesn t use the Draft N.

  If you want to use the Draft N then this standard Wlan key must be activated in the router WLan and Wlan card settings!

  Wlan card settings can be changed in:
  Device Manager-> Wlan card properties-> Advanced tab

• Difference between Tecra M10 and Tecra A10

  Dear forum
  The above says everything really.

  I see the two look identical, but one is smaller. These two models are different in other ways please.
  Ian

  Of course, the two laptops are different.
  There are different models Tecra A10 and there are different units Tecra M10.

  For example:
  Tecra * A10-13 b * supports Intel GM45 chipset and an Intel Core 2 Duo P8400 2.26 GHz CPU.

  Tecra * A10 - 1 2 * supports an Intel Core 2 Duo T9600 2.80 Ghz CPU Intel GM45 chipset

  You can find details of different laptop models left here:
  http://www.Toshiba.EU/discontinued-products/
  Then, you can compare all the pieces of hardware.

• How much memory can I mount in a Tecra M10 - 1CN?

  How much memory can I mount in a Tecra M10 - 1CN and should be in two 200 pin SO DIMM DDR2 PC2-6400 800 MHz modules

  Hello

  Expand the memory depends on the chipset of the motherboard
  The Tecra M10 supports the chipset Mobile Intel GM45 Express and this chipset DDR2 800 MHz RAM 8 GB max

  So first of all, that you can use 2 x 4 GB RAM modules, and on the other hand the speed of memory is limited to 800 MHZ.

  Even if you use faster modules i.e. 1033 Mhz FSB would clock speed to 800 Mhz so it s not worth to use faster than the DDR2 800 Mhz modules

• Tecra M10 compatible mSATA?

  I have a Tecra M10 - 1KR (chipset GM45/GM47) and want to upgrade with a XM13 of a - DATA 60 GB (mSATA). There is a mini slot unter PCIe free keyboard, but unfortunately, I couldn't find any information if the motherboard accept the mSATA modules.

  Cordially, Harald know.

  I can't say with certainty if this mini PCI module would be compatible.
  Always is the TECRA M10 is equipped with Intel GM45/GL40? Cantiga (G) MCH? North Bridge, Intel ICH9M as South Bridge and R5C847 as a controller of the card.

  The two Mini-PCI card slots are used for 3G or Intel Turbo Memory and WLan
  Some models support Intel Turbo Memory.
  Intel Turbo Memory (Robson) PCI Express Mini Card slot 2 and also some models are equipped with a 3G PCI Express Mini Card type card in slot PCI Express Mini Card 2.

• Upgrade CPU to Tecra M10 - 13Z PTMB0E-01400LGR

  Hi, I want to improve my Tecra M10 with the CPU max supported. In fact, I have the Core Duo processor T5670 installed. Can someone give me info on the capabilities of the M10?

  Thank´s in advance.

  Concerning

  Astra

  Hello

  Theoretically, you can use a CPU that is supported by the chipset.
  As far as I know the laptop supports the Chipset Mobile Intel GM45 Express.
  So you can see the Intel Gm45 Mobile Intel properties page and what would the supported processors.

  In general CPU upgrade a tricky thing but is stronger CPU produces more heat dissipation and could lead to overheating.
  In addition he s not 100% sure that BIOS would support the new processor.

  I also found this nice doc from Toshiba:
  Is it possible to upgrade the CPU or GPU of a Toshiba laptop?
  http://APS2.toshiba-tro.de/KB0/TSB9401AX0001R01.htm

• Tecra M10 - Sound does not work on Windows XP SP3

  TECRA M10 sound does not work with Win XP SP3

  1. the drivers from the toshiba web site.
  2 chipset drivers and audio drivers were reinstalled no luck,.
  3. no mute FN + Esc
  4. feature eat that all drivers ok

  Hello

  If I understand your right all devices listed correctly in the Device Manager and you don t have yellow exclamation points?

  Normally, for high definition sound cards, you need two patches from Microsoft:
  KB835221 and KB888111.
  Normally, these patches are integrated into SP3 but it works only if you install the audio driver after SP3. So, if you have an older version of XP without SP3, you must update to SP3, all first and then install the display driver.

  So in your case, you must delete the current sound driver and restart the laptop. Then use CCleaner to clean the registry and system files. Reboot the laptop. Then download and install the driver of his newest Realtek Hompage.

  Good bye

• Tecra M10 does support VT?

  Hi all

  I have a Tecra M10 - 13 K 8 GB RAM (PTMB0E-01600LGR) BIOS V2.10 with Intel T5870 CPU (which is not taken in charge VT). My Chipset is Intel GM45 Express.
  I want to install Ubuntu 9.10 (64 bit) with VMWare Server 2.0.x and create Virtual Machines with Windows 7 (64-bit) and Ubuntu 9.10 (64-bit).

  But my CPU does not support the VT!

  Now, I want to buy Intel CPU T7250 and replace my old CPU. Would this work? The BIOS must support the? Do I need a new Version of BIOS?

  Thank you and best regards,

  Hello

  First of all you cannot use virtual technology if the processor does not support this feature.
  Second, the replacement of the CPU is not desirable and often delicate!
  The BIOS has not been tested with a different CPU, and no one can tell if the laptop would be stable after an upgrade of the CPU.

  Take a look at this Toshiba doc:
  http://APS2.toshiba-tro.de/KB0/TSB9401AX0001R01.htm

• How does 3G on the Tecra M10 - 11V?

  I don't know how the capablilty of the 3G works on the Tecra M10 - 11V.

  A few ideas come to mind. With a different (a lenovo laptop), I noticed that the chipset integrated 3 g Vodafone is blocked. I also saw on another laptop space for a SIM card from a network of my choice.

  Judging by the previous posts, it seems that there is a space for a SIM card in the laptop.

  Anyone would be able to elaborate on this?

  Thank you very much!!
  Jon

  Remove the battery, you know a SIM slot?

  My friends Tecra M9 has a 3G slot and it can use any SIM. To make it work under Windows, it had to enter the proxy of suppliers in 3 G connection manager, then he worked :)

• Tecra M10 - GPS not taken in charge after the update of the WLAN driver

  Hi all

  I have a Tecra M10 with brod f3507g mobile modem. After Wireless manager driver update (suggested by TEMPRO) gps utility is not working: the error msg is "gps not supported!

  Of course before the driver update gps worked fine.

  Anybody experinced same problem?
  What can I do to fix this?

  Thank you

  Hi ouebgi,

  Have you ever tried to restore the old WLAN driver in Device Manager? There are a restore function for the previous version of the driver and you should try it!

• Tecra M10: Intel Proset Prelogon fail

  I have a Toshiba Tecra M10, which has an Intel(r) WiFi Link 5100 AGN inside.

  I have wireless installation before opening of session with Intel proset software worm 12.2.

  When I cold start and try to connect immediately he failed to open a session.
  If I'm cold starts, wait 10 minutes, it connects fine.

  Any ideas what could be causng this?
  Is there something to load before I login?

  I inquired with Intel too and waits for a response. By covering just the basics!

  Hey Montana

  Can you please try it for me?
  Can you check the WLAN functionality if you enable mode 802.11 g only?
  This connectivity problem there?

• Tecra M10 - update of the BIOS says "this computer is not supported.

  Recently refurbished a M10 - 10I to reinstall the operating system. WinXP install at all so I try to update the BIOS as it seems quite old (V1.5). Most recent version (and is available) for this machine seems to be V3.0. Download and try to run the file "P0065V300" and get the message:

  Package for the TOSHIBA BIOS ver.3.3.0
  This computer is not supported

  What can I do? Its supposed to be for this model!

  Also, prefer a version of boot drive, but hey, I can use a version of Windows, assuming that it runs on Win7.

  Hello

  Tecra M10 - 10I belongs to the series of PTMB1E and according to the page of the Toshiba UE driver, BIOS v3.00 - WIN is the latest BIOS version which is available for this model.

  The BIOS update requires a few additional tools Toshiba as VAP (additional package for Win 7)

  If this driver isn't installed, the update of the BIOS would not work.

• Tecra M10 - stuck - CTRL key question may be to do with the BIOS?

  Hello and thanks for reading.

  I recently changed my Tecra M10 to Windows 7 (from XP), and it quickly developed the dreaded question-button stuck CTRL This causes the keyboard behaves as if the CTRL key is pressed continuously. Sometimes reaching a key combination, or bring up the on-screen keyboard, temporarily solves the problem, but he returned.

  It seems to be a problem that many people have no simple solution. I watched each thread that I find and tried a lot of things to do with drivers etc without success.

  So first of all, if anyone knows a remedy that works for this particular machine, I would be very grateful to hear!

  Then, there are two things that I did not yet: updating the BIOS and turn off pinch zoom.

  I was watching the following BIOS update:

  http://www.Toshiba-Asia.com/SG/support/drivers/details/25244

  ... which is the version 3.00 and seem to be more recent. My version is 1.90.

  However, version 3.00 is labeled "for PTMB0 * ONLY. I don't know what that means or if it applies to me. Can anyone help? Should I install this BIOS?

  For the pinch zoom, I was informed that disable sometimes cures the problem CTRL - but I can't find any installation zoom pinch on the M10. I think he doesn't have any one. Is this fair?

  Thanks much for any help you can give.

  Hello

  > I was watching the next BIOS update. is the version 3.00, which seems to be most recent. My version is 1.90.

  There are different Tecra M10 models on the market.
  Check the labels at the bottom of the unit. There you should find numbers like for example PTMB0E-01K00LGR

  The first 6 characters are important: for example PTMB0E

  I guess that your laptop belongs to the series of Europeans.
  In this case, you should check the page of the Toshiba UE driver for a possible update of the BIOS.
  http://www.Toshiba.EU/innovation/download_drivers_bios.jsp

  However, on the page of the Toshiba UE driver you will also find the BIOS for all European units Tecra M10 v3.0.

  Anyway, back to Ctrl + button question: guess what, you need to connect an external USB keyboard and must check how is the CTRL key.
  In case the USB keyboard would work properly, the internal keyboard CTRL key is assigned and you will need to replace the internal keyboard.

  PS: it would be possible that the "sticky keys" option has been activated. To disable this feature, you must press SHIFT 5 times in the line.

• Need new cable supply for Tecra M10

  Hello. My Tecra M10 power cable has split (after only 4 years used). Can someone tell me the right product to order?

  I have more information if necessary.

  Kind regards

  Thomas

  Hi Thomas

  Do you need AC adapter or just cable that connects the adapter into a socket side and wall on the other hand?

• Tecra M10 - 10z - 3 G does not work after installing Win 7

  Tecra M10 - 10z, I installed Windows 7 pro 64-bit
  Everything is correctly configured, but the 3G connection does not work: the message is "no network".
  with Windows XP is ok.

  I can't update the firmware or similar.

  Y at - there someone who can help me?

  TKS

  Hello

  To use the 3 G, you should first check whether the module G ericsson 3 has been successfully installed.
  Where there is a visible yellow exclamation point in Device Manager, the 3G driver must be reinstalled.
  I found on the page of the Toshiba UE driver:
  [Driver Win 7 3 G Ericsson | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 5 & selSeries = 148 & selProduct = 813 selSho rtMod = null & language = 13 & selOS = 30 & selType = 295 & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = 295 & page = 1 & ID = 71930 & DISO =-1 & driverLanguage = 42]

  Additionally, make sure that the 3 G RF power control utility has been installed properly.
  3 G RF Power Control utility"turns your 3 G at the start.

  This tool can be found here:
  [3G RF Power Control utility for Win 7 64 bit, | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 5 & selSeries = 148 & selProduct = 813 selSho rtMod = null & language = 13 & selOS = 30 & selType = 322 & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = 322 & page = 1 & ID = 73658 & DISO =-1 & driverLanguage = 42]

  Hope the 3G network functions the reinstallation of these two tools.