Wireless dropouts WAG320N

Similar Questions

• Computer crashes when the internet connection is detected

  Hello

  Need help with my dads pc, it is running Windows XP SP2 with IE7, the computer crashes as soon as an internet connection is detected, I have to remove the usb adapter WiFi to regain control of his PC, we use a model Linksy Cisco Modem ADSL2 + Daul-Band Wireless - N WAG320N, which is used for a certain number of laptops xbox and ps3 with no problems whatsoever.

  The system works very well without any problem until what the internet is detected and you must reset the computer of the tower base, we have tried a number of different usb adapters and a pci card but have the same result, a computer from freezing. I tried a number of different articles of this site, but all have failed, so it's my call for help to get my dads pc back on the internet, if I could get answers to the English plan as im not as good as I used to work on these systems.

  Help, please

  Kind regards

  Phil

  Hi Phil,

  1 have you made changes to your computer recently?

  2. you receive an error message when you try to connect to the Internet?

  3. what happens when you try to connect to the Internet by cable?

  I suggest you to follow the steps and check if it helps.

  Method 1:

  Step 1: Start in safe mode with network.

  To use a safe mode with network option, follow these steps:

  (a) restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  (b) use the arrow keys to choose Safe mode with networking in the Windows Advanced Options menu appears, and press ENTER.

  Step 2: PEd a clean boot and then check to see if it helps.

  How to configure Windows XP to start in a "clean boot" State

  Note: Make sure you perform the steps in How to configure Windows to use a Normal startup state

  to start your computer normally.

  Method 2: Update the network adapter and check if it helps.

  Updated a hardware driver that is not working properly

  Note: This link is applicable for Windows XP.

• WAG320N wireless problems

  I am having major problems with my Linksys WAG320N. Hoping someone here can help as I am quite clueless when it comes to networking.

  Without changing the settings, the other day that my Macbook Pro could not connect and he kept saying 'timeout '. From that point my iPhone also refused to sign, although access to the internet on my MBP viaethernet was fine.

  I did a hard reset according to the instructions of this forum, and then re-configured with the installation CD. The router wireless light was turned on but my MBP did not see the network. Finally, I managed to connect after I restarted my laptop and enjoyed every 10 minutes without internet connectivity before wireless problem network come fall and now does not appear in my list of networks once again, even if the wireless light is still on.

  Ethernet connection still works, but not via the wireless.

  I restarted my laptop and the router and tried switching channels on the router, all to nothing done. Very confused and frustrated!

  Someone at - it suggestions? Thanks in advance for any help.

  What is the wireless settings you have set up on your router (SSID, channel and security mode)?

  Connect to your router configuration page and click on the Wireless tab and click on the "Advance Wireless Settings" sub-tab and under change 75 beacon interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...

  Now let's see if you can locate your wireless network and try to connect...

• wireless client cannot see wired - WAG320N

  Hello

  my modem/router WAG320N works fine but the wireless client cannot see wired and vice versa. they are in the same network (192.168.0.), using the same 255.255.255.0 mask, same workgroup firewall and Yes to enable all packages in and out. IP addresses are DHCP form.

  Internet sharing works fine, but when im trying to play any game on LAN wireless clients peuvent see their car but not wired. when im trying to client ping wireless from a wired machine it does not either.

  What is intresting in a DHCP reservation or the ARP table (in router configuration) I can see cable and wireless customers. but still they do not see each other.

  help pls!

  Hi again,

  I went to PC World and they exchanged this WAG320N to another. but this time I went to ASUS RT - N16 and so far all is working correctly. I know its missing adsl modem but got usb 2 and a print server.

  Sorry cisco...

  thx for your help guys!

• WAG320N very bad 5 GHz wireless signal.

  Hi all

  Because I live in an apartment building, I decided to buy a proper router on 5 GHz. I see each of them and at least 12 wireless networks 2.4 GHz (mainly BT HomeHubs or other boxes UK ISP wireless). I am studying the CCNA and our teachers recommend cisco routers (linksys) as the best. I bought a WAG320N as one that suits that I could find on the British market for a reasonable price. The problem is that I have less signal on 5 GHz on 2.4 GHz I have 50% maximum of the 5 GHz signal and speed is usually lower than 802.11 g, average below 64Mbps! I can't believe. When I change 2.4 GHz signal has up to 80% as my old router TP-Link. The speed is more often up to 65Mbps, means awful. I have seen a lot of topics on this particular router but I couldn't believe that to sell Cisco products these awful and unreliable as this router. I tried to change channels on 5 and 2.4 GHz but it's always the same, the wrong speed and weak signal. My wireless card is Intel WifiLink Advanced-n 6200 and Sabayon linux and Windows 7 operating systems. I have a laptop and it is CCA 6 meters between the router and there are 2 walls. The router is still under warranty so I will not hesitate to return to PCWorld...

  Thanks for your help.

  I solved it. I moved the router more near my room. There is only one door of the room between the router and my laptop. Signal has cca 90% and the speed is especially 270 or 300 Mbps.

• WAG320N

  Oh dear... what a disastrous start

  Firstly, installation and firmware seem to be corrupted.  Resettlement on the site Web has not helped.  I say this for several reasons:

  (1) no way to change the routers IP, no way to change the time zone, in fact, no way to change the settings.  All seem to accept, reloads the same page and done... NOTHING

  (2) no way to pass wireless turned off... in fact it seems that some of these wireless options menu options are missing.  Great stuff.

  Actually by and large, no way to configure the gateway at all.  For example,... can Cisco we get a new firmware?  Perhaps a gateway which is in fact out of the test products and works?

  I am very annoyed because I just took a wag160n, which was chronic to say the least, for this model later... What does'nt seem to even work at all... At least despite declining regularly the internet and the wireless, the 160n actually you are allowed to configure it.

  Help?

  Fixed.

  It seems that unlike the WAG160N I got, it will not set up through anything other than Internet Explorer.  I have no idea of what is different, but something is.  In any case, Internet explore 8 installed and the gateway configured by OK and everything is right with the world again.

  No Wi - Fi dropouts don't like with the 160N

  No Internet goes as with the 160N

  Program installation CD has had little love and it doesn't take an age to load upwards and the config of the gateway to the first use.

  Streaming movies HD 1080 p for PS3 is also impeccable Wireless N 280Mbit with 1Gig port connected to the PS3.

  Overall, now I realize that I have to use IE instead of chrome or Firefox is the product I've been waiting for.

  The WAG320N after works OK is a great replacement for the flawed WAG160N.  The WAG160N but I would avoid like the plague and save up the extra for this one.

• Airport Extreme + Express + older Express audio dropouts

  My setup is as follows:

  Coaxial cable-operator-> cable modem provider-> Airport Extreme via Cat5e

  Express #1 a few feet away, analog stereo output, extreme network expansion

  #2 2 parts away, similar stereo out, Express extreme network extension

  2014 Macbook pro, Yosemite

  When I broadcast iTunes on Express #1, is generally well from anywhere. When I listen to #2 (either by itself or in addition #1) I get occasional audio drop outs anywhere, the macbook is, even though my internet remains stable. For example, the macbook is right next to the Express #2, streaming internet radio and play through internal speakers. When I send also the audio to Express #2 (multiple speakers in itunes), which express audio stream is sporadic, although the internal speakers turned on constantly. I would have thought dropouts would leave as the macbook approached #2, but there is virtually no change.

  If the macbook is right next to the #2 Express, he continued directly towards the #2 or that made a trip to the extreme and #2? Possible Express #2 is working to expand the network ok but does not just for airplay? It is a first or second generation.

  Thank you!

  What are the exact models of each of your airport base stations?

  When I broadcast iTunes on Express #1, is generally well from anywhere. When I listen to #2 (either by itself or in addition #1) I get occasional audio drop outs anywhere, the macbook is, even though my internet remains stable.

  The main path that AirPlay takes when streaming to your configuration is:

  • Starting from the host of iTunes MacBook to AirPort Extreme.
  • Extreme for:
    • Express #1 if this Express is chosen as the "speaker" AirPlay, or
    • #2 has been chosen as speaker, express or
    • At the time, if the two were chosen as speaker.

  Thus, it is possible that the path includes several obstacles (walls) for AirPlay to go.

  If the macbook is right next to the #2 Express, he continued directly towards the #2 or that made a trip to the extreme and #2?

  AirPlay, in theory, go first to the base station that iTunes host is connected to.

  When you extend, you lose a significant amount of bandwidth just to keep the network wireless in this configuration. So the question is: do you really need to expand your network or continuously more important for you?

• RALink RT5390 wireless adapter does not work

  My g6 pavilion laptop wifi adapter was not properly work recently. my internet router and networking are works well as it should, but whenever I restart my laptop, repeat me that there is no link and no other wifi networks when there are clearly other networks because of my neighbors.

  I tried a system restore to solve the problem, but it has no effect and my norton affects the restoration of the system to disable the antivirus.

  I'm stuck on ideas to solve this problem and I don't know much about networking and internet stuff, so I'm pretty powerless here

  Here is a link to my features of laptops if necessary:

  http://support.HP.com/us-en/document/c03136241

  These ralink adapters are simple ol ' sh * t. I don't know if it will be a complete solution for you, but I was pulling with my network card for months and this has proved to be the most effective for my computer. I have a HP Envy luck to be equipped with a Ralink RT3290, Windows 8.

  so...

  Out of the box, my computer was working fine and it connected to the network OK. As soon as I moved further away from the router, I known constant dropouts, and the connection always folds between the low signal strength, to completely disconnect the router, where I had to re - connect manually there. This question really frustrating. I use my computer on the top level of my house, and the router is in the basement. If I was getting sick of this fast. Update driver after update driver, no luck. After trying everything under the Sun, I decided I would bite the bullet and I tried something a little bit Orthodox...

  I just uninstalled the driver for my computer. Yes, really. When a component on your computer a driver is stripped, Windows software has a few drivers that will install by default for your material so that it can remain functional on your computer. So, once remove the driver ralink on my computer, windows installed sound driver by default for my network card and... Voila! My connection problems are virtually non-existent at this point. The material is not always the best, but at least I can surf the net in my room without my connection affected by constant stalling.

  Now, other that the light on the button stuck wireless with an orange glow and list my NIC as #10 Device Manager, I always use this driver with minimum questions. Occasionally, he'll forget the connection once I wake the laptop from sleep, but this issue has been much worse with the ralink drivers than without.

  If you are aware of the risk (what is low, to be realistic, this can always be undone and you can always reinstall drivers ralink so that deosn proved to be an effective solution), I will explain in detail how I managed to do.

  (1) open Device Manager (right click the lower left corner in windows 8 and a shortcut appears in the drop-down below)

  (2) find network adapters and display its contents

  (3) make a right click on your wireless network adapter (should be something similar to "Ralink RT5390 802.11b/g/n... ") and click on"Uninstall"in the menu drop-down

  (4) a popup should appear and you should be given the possibility to uninstall or cancel it. Make sure you check "suppression software driver for this device" until you go forward, or Windows re - install the ralink driver.

  -Search for new hardware if your network card is not detected after you have uninstalled it. Your card should appear as "802.11n Wireless LAN card"

  -If you have an installer driver ralink that is newer or equal to the driver that is already installed, you can run the Setup program to remove any driver software remains which is usually overlooked by the device during the uninstallation Manager there from your computer

  -As an option, you can check potential driver leftover files C:\Windows\System32\Drivers. It is important to search for remains that Device Manager / ralink Installer may have missed because it can potentially conflict with the replacement of windows WLAN driver. pilots should have a short name for your adapter (e.g. rt3298.sys); they shouldn't be hard to find. Be careful as well; IT IS WISE TO ALWAYS SAVE no matter WHAT DRIVER SOFTWARE, YOU CAN REMOVE in CASE YOU MAKE a MISTAKE.

  (5) re - enter your information network and you should be good to go!

  I hope that it is of no help to you. People who know nothing about what they will tell you to install the latest driver and yatta yatta yatta this way, because it does not work I had to take the liberty to try to find a solution for these adapters cursed myself. I hope this helps a bit your question!

• Satellite L650 - uninstall driver Bluetooth wireless

  My home broadband connection is LAN wireless
  I have
  has been seen dropouts intermittent and trying to find the reasons for which I inadvertently allowed Toshiba Bluetooth to download a driver. I get now constant warnings that it will conflict with my original CD! They suggest I have contact Support and the days have tried to do it now.

  I have not saved the driver. How I "stop" it or uninstall it? My system is Toshiba Satellite 650-administrative appropriations on I / E 9 - Win7 -.

  Thanks for all the ideas on this subject.

  Hello

  Sorry, but the whole story is very confusing and I have to ask for things to understand this

  > why I inadvertently allowed Toshiba Bluetooth to download a driver.
  I think you have mixed up something software Toshiba Bluetooth up to not download nor install any other drivers or updates automatically. So what program exactly tell you?

  > I get now constant warnings that it will conflict with my original CD!
  You can post a screenshot of this warning? I've never heard anything like that.

  > I have not saved the driver.
  What you mean with the registry. Either the driver is installed or not.

  > How to 'stop' it or uninstall it?
  You can uninstall what you want. Just navigate to control panel > uninstall a program and select the program you want to uninstall.

• Portege R700 PT310A Wireless connection of abandonment

  I just receive a R700 PT310A-05N011 and my wireless guard stall repeated.

  I updated to the latest version of the bios and checked the broadcom drivers.

  Someone at - it the same problem. I have win 7 64 bit installed

  Hi mate

  Have you noticed what Wlan dropouts using the battery power only, or do you have this problem also if the laptop is connected to the power adapter?
  I had a similar problem, Wlan, but only using the power of the battery.

  I noticed that you may change your economy option in Win 7 the power supply WLan management and this has solved the problem.

  You should try it also disable it for the Wlan to save energy and check if it would improve the performance of Wlan

• Time Capsule wireless bridge

  After great to work for a year, I had problems recently with Time Capsule using our router, abandonment, etc... As did others on this forum, we had mult calls to ISP about the quality of the line. They said that we were crashing our data upstream limit, which blew our connection. Looks like iCloud with services of Photo services were the problem. We have Mac running 10.9.5 but daughter improved to Capitan and using the services of the most recent and cloud. Without the ability to limit the range of QOS, I had to get a new Nighthawk so I could limit QOS upstream to 80% of the capacity which has not dropouts. Now it serves as main router. I wired TC as an expensive network switch and for Time Machine backup hard drive. Has any found a way to connect the TC wireless? (I want to go the new router to more central location and keep TC where it is on the lower level) This threshold door Base Station to its former network password and have / send mode wireless network and network/router - Off Mode (Bridge). I am currently letting Netgear assign the full range of DHCP, but ready to try a limited on the main router range and let the TC have then end of range ( LaPastenaguesolution). But the problem seems to be that the TC will only see signals from other devices of Apple wireless? If so, then no devices Apple more for me.

  6.3.2 (632,3), TC 7.7.3, OSX 10.9.5 Airport utility

  Has any found a way to connect the TC wireless?

  Not much of interest to spend time on it to try to find a solution... when the firmware for the TC will not allow this.

  An older version of 'flat or square' TC working in tandem with an older version 5.x of AirPort utility would allow a manual workaround solution, but no luck with the latest TCs and 6.x newer versions of AirPort Utility... or the most recent TC and the older utility.

  Looks like no Apple devices more for you, unless you want to consider a wireless Ethernet bridge to feed the TC signal he wants.

• U410 - Wireless worsening performance - requires a reboot for operation

  Hi all

  I recently bought a U410 and I, like many others, am having problems with wireless connectivity. When I got to the laptop, I rarely had no problem with her. However, it slowly deteriorates and the possibility to connect to different networks is getting worse. More I cannot connect or have frequent dropouts.

  The real question, however, is that to be able to connect to a network once again, that I need to do a full reboot. Disabling the network card is not enough, or running the Windows 8 troubleshooting tools. It is incredibly frustrating to have to completely restart to get back online and lose my place in the browsers/documents/etc. Does anyone else know similar problems?

  I tried to contact Lenovo about a refund for my U410, but apparently the window of eligibility has spent two weeks and they refuse to make an exception. Needless to say that after years and years of Lenovo computers this will probably be my last, because performance is so much cheaper as I expect them...

  Thank you

  B

  
  

• Stream Mini 200-010: upgrade BCM43142 on HP Mini 200-010 Stream wireless

  I have upgraded to Windows 10 and because of the location of my residential gateway (RG), I'm limited to wireless. I want to upgrade the card to an AC class with bluetooth wireless. I have updated the drivers, but still have a dropout.  Someone at - it a good upgrade adapter known? I replaced the card in my laptop and it connects now reliable tape 5g without abandonment.

  Sorry, that didn't work.

  I guess you'll have to opt for the Broadcom AC card that I posted, and if you want just the card dual band N, you can go for this one...

  Broadcom BCM943228HMB 802.11abgn 2 × 2 Wi - Fi adapter, card Broadcom Bluetooth 4.0

  HP Part # 730668-001

  You never said if your PC has a Celeron or Pentium processor.

  As I said the other day, people who have tried a 7260 Intel wireless card in a laptop with a celeron or pentium processor... it does not work.

  I have no idea why it doesn't work.

  Year YEAR Intel 7260 works wonderfully in my G1 350 with the 4th generation core i3 when I replaced the broadcom stock card.

• Do cRIO 9014 Wireless

  I'm working on a project which, due to the location of the cRIO he will be no close ethernet cable. A solution that I've looked at is to connect a wireless for the cRIO bridge and then connect the bridge to a signal from router available. I looked at the first competition and they use this solution to control of robots. Does anyone know how it works and if it is a reliable solution?

  I have to install it at school so I don't know if this works with DHCP or if I should request a static IP address.

  Gerardo Trevino,

  I helped with the FIRST Robotics competition and the only problems I've ever seen with the wireless setup were typical problems related to Wireless Communication (range limits, network dropouts, etc.).

  To make your cRIO wireless you can definitely use this method and it should work perfectly, I did personally and have not had any problems.

  Check out the tutorial that we have on our Web site for making of PACs wireless NOR industrial Wi-Fi access points. You can also see the 3rd party WiFi Module cRIO.

  It is possible to do with DHCP, but set all of your addresses statically makes things a lot easier in a closed/private network environment.

• Problem solved (rt3290 of abandonment and low signal Ralink) wireless card

  Dear owners of Hp

  I recently bought a new Hp laptop which included the defective Ra link rt3290 wireless adapter, included sypthoms was frequent dropouts and forces signal flucatuating. The card was on a 5.0.45.0 Version, I tried to update via the driver properties in Device Manager but ended without any result.

  There were more messages by many hp owners on face similar problems with this card, I tried all possible solutions, including, by checking the box, other wlan adapters, go back to the previous version of the energy-saving stop disabling driver.

  I think that I ve found a solution via a simple update here

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149767_1#tab-history

  Download version 5.0.53.0 Rev D and when said when a previous version of the driver were found after installation, click on the replacement of all previous features. The update has now fixed the problem and my wifi signal is strong and did not have a single drop out.

  I hope that I have provided some form of assistance, some feedback would be nice, thanks.

  Hello:

  Happy is he who solves the problem for you.

  There is a newer version if you want to give that a try (5.0.56.0 Rev.D (June 10, 2015)).

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149767_1

  But as the saying goes... "if it ain't broke, don't fix it."