With 0124 disk error disk failure...

Similar Questions

• I have windows xp professional operating system at boot it stops with error disk failure (40) and will not start windows can help u

  If I press f1 it will then boot to windows, but I need to cure the problem with the disk error message

  Hello petertomblin,

  It seems that this message is coming because of settings in the BIOS.

  The computer has a floppy drive?

  If so, is it operational?

  Nevertheless, we want to get into the BIOS and disable the startup procedure floppy drive,

  It is this best with support of the manufacturer of your.

  PLEASE NOTE:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Best regards

  Matthew_Ha

• Pavilion 11-n010dx: disk failure hard error long dst Pavilion 11-n010dx

  I realize after searching for the error that my only solution is to replace my hard drive but I need some advice on what exactly, I need with respect to a new hard drive. Not very tech-saavy. Please notify.
  Failure id 9fnhbr-7b783q-xd7v6k-61ed03.
  Thanks for any help.

  Here is the Service Manual:

  Manual

  Replacement hard drive is shown on page 36 of the manual. Your laptop, plug, came with a disk 5400 RPM 500 GB. This model uses 7mm superslim hard drives is as well as what you buy. There are also options for a solid m2 or normal size state drive solid state SATA drive as a replacement for the mechanical drive slow 5400 RPM. In other words, it would be the perfect opportunity to speed it up a little.

  It would be a 7200 RPM mechanical drive of 500 concerts and would be a good replacement at low cost:

  http://www.Amazon.com/Seagate-laptop-7200rpm-cache-ST500LM021/DP/B00ISKS416/ref=sr_1_2?ie=UTF8&QID=1462017567&SR=8-2&keywords=7mm+laptop+hard+drive

  Solid state drive designed to replace the hard drive:

  http://www.Amazon.com/Samsung-2-5-inch-internal-MZ-75E250B-am/DP/B00OAJ412U/ref=sr_1_1?s=PC&ie=UTF8&QID=1462017682&SR=1-1&keywords=Samsung+850+Evo

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Dell xps 8100; Disk failure hard error 2000-0142 0 self test status 79

  Hi guys, I was wandering in the forums for a few hours, now looking for ana response to this question, and can't find anything clear. I have a XPS 8100 that I run a diagnostic and received a 2000-0142 error code that says MSG: error code 2000-0142 hard drive FAILURE 0 self-test status: 79 based on what I read in the forum is that there is a disk failure, and the only recourse is to solve the problem in my view is to replace the drive. Firstly, can someone please give me an absolute confirmation that it is indeed what I have to do, or is there something else I should do to fix this problem first? If a replacement drive is there someone could please tell me how can I do to get my OEM software off the coast of the partition recovery and on my new drive. I now office preinstalled and, of course, premium Windows 7 I would like to see on my new hard drive and I was not provided with one of the disks at the time of purchase. Thanks in advance to all those who respond

  Hi XPS8100kid,

  Welcome to the Dell Community Forum.

  The 200-0142 error is for hard drive failure and you need to replace the hard drive.

  Since the hard drive has not, you would not be able to access the partition recovery on it. Data would be lost and the software already installed on your computer will need to be reinstalled.

  Windows 7 will need to be installed on the new hard drive. Please click the link below to get the procedure of re - install Windows 7.

  http://Dell.to/15MYHsz

  If based in the United States, you can ask for the backup drives by clicking the link below:

  http://Dell.to/Zj7oHA

  I would like to know if additional assistance is needed.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit our Support Site .

• My computer keeps showing disk failure smart error

  My computer keeps showing on the startup splash screen and also my system completely stopped backups from disk failure smart error

  and my DVD/CD ROM burner a work stoppage indicating the red light on my bright area of the lens. and has same stop indicator to the area of manerg of tasks

  The error means that the hard drive is faulty and should be replaced by a new.

• I got lightroom 5.5 on a computer with a hard disk failure. How do I install it on my new computer without access to the old computer?

  I got lightroom 5.5 on a computer with a hard disk failure. How do I install it on my new computer without access to the old computer?

  You can download Lightroom 5.7.1 (the final version of Lightroom 5) from the following Web site: keeping up-to-date for Lightroom

  Lightroom 5.7.1 is a solid version, and you are entitled to it. You will need your serial number to activate the installation.

• Impossible to turn on the virtual machine with the following error: could not open the disk ' / path/to/vmdk-0001.vmdk ' or one of the Flash disk it depends on. Reason: Broken pipe.

  After the movement of virtual machines in VmWare Server 2 for ESX 4i, I get this error when you try to start the virtual machine:

  Impossible to turn on the virtual machine with the following error: could not open the disc

  "/ path/to/vmdk-0001.vmdk" or one of the Flash disk it depends on.

  Reason: Broken pipe.

  Anyone's idea what is the problem here?

  How did you move virtual machines?

  Did you use the converter (https://www.vmware.com/tryvmware/?p=converter)

  Otherwise try converter

• HP Pavilion 400-434 Office: intelligent control of hard disk: failure

  Hello

  It all started when the computer would go blank right after startup, the HP logo would come upward, then 'auto repair preparation", more... Just empty. After reading the forums online, I did all the possible troubleshooting steps and at the end I did the SMART test... the result was:

  Verification of the processor: past

  Intelligent control of hard disk: failure

  Failure ID: RGD7MK-7HV7RC-9XJ16K-60BB03

  After obtaining these results, when I turn on the computer, it gives me a blue screen saying: drive SMART 1 error (301) and told me to test once again, that I did and got the same result as above.

  Here is some info from the computer:

  Model: HP Pavilion slimline 400-434

  Processor type: pentium (R) of the Intel (R) J2900 @2. 41 GHz

  Thanks for your help!

  Hi there @Brugalgirl

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that your computer does not start successfully, and you found a Smart Drive 301 error code. I'm happy to help you with this.

  I checked the ID of the failure, you've posted and verifies that the error. Unfortunately, this means that your hard drive needs to be replaced.  In view of the fact that the system does not boot, it is likely that the hard drive is completely unreadable, but depending on what you have on this subject, it may be worth your while to check with a local computer service shop and see if they can help to recover data from your hard drive.

  If your system is relatively new and may be covered by the warranty, or if you wish to fix with HP for the guarantee system, you can call in hotline to make these arrangements. In this case, please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Otherwise you can look at a replacement hard drive yourself. If you have a set of recovery media, then you already have a factory image HP, which allows you to put in place a new hard drive with your original operating system. If is no longer, you have a set or did not have a set of recovery media, so you can see if there are not yet available for your model.

  HP computers - get HP recovery disks or HP USB recovery disc

  Let me know if you need help most. If it solves your problem, please mark this message as a solution.

• HP Pavilion notebook PC A7H25UA #ABC g6 hard disk failure

  Hello

  My laptop started with this error message: hard disk failure: Q0FAJ2 - 66 X 756-MFGK1F-60F803 and past Q0FAJ2-66X74H-MFGK1F - 60CT 03. I run the hard drive test and they both failed.

  What can I do to solve the problem?

  Thanks for help me!

  You'll have to replace the hard drive. It is not as difficult as you might think. If you can do this:

  http://www.YouTube.com/watch?v=3AlMZFGwegE

  post then back and let us know the country you live, and we can help you find the best price on a good replacement and will guide you through software and data recovery/reinstallation.

• Impossible to fill out the case of the composer from vm - hot add disk failure

  I'm checking a pool of composer, but the extraction fails with the error to the user saying "no server available for this transfer.

  and the connection to the server has the following sequence of warnings in the application log

  EventID 104: No server available transfer to transfer VMS/datacenter/PathtoVM/PoolDesktopVM not name Session: SessionIDString

  EventID 104: Session: SessionIDString reason no. ready transfer servers have access to storage for the VM me: vm-xxxx disk key: 1234

  EventID 104: Session: hot SessionIDString add to the user disk failure: username desktopDn:CN = name of the PoolDesktopVM

  The snapshot that depends on the pool has been published on the forwarding server and comes to 2.9 GB. He could not be connected, but the extraction of the VM based on that snap fails 3.0 GB on the 3.7 GB the customer view says he has to download

  The virtual machine with the snapshot is windows XPSP3 on hardware v7 with vmdk stocked thickness 1.

  The composer generated obtained vm controller buslogic scsi parallel and 3 thin provisioned vmdk added to chain SCSI 1 to account for the persistent drive of the composer and the disposable disc over the virtual machine swap file.

  The composer added 3 discs would explain the remaining space, that the customer has left to check.

  The forwarding server is hardwarev7 using the parallel scsi controller free such as recommended in the view 4.6 installation guide

  Can someone help get beyond the hot disk failure add that seems to be triggered when (I guess as the forwarding server) tried to mount?

  Hello

  It is a requirement. Transfer server THAT VM needs to access the desktop under transfer disks. in other words, host th transfer server running vm must be able to access disks of office under body.

  -noble

• ASM Diskgroup with 1 disk? Is this possible?

  setenv ORACLE_SID + ASM
  sqlplus "/ as sysdba".
  SQL > startup nomount
  SQL > create diskgroup data disk ' / dev/dsk/c0t5d1s4 ";
  SQL > shutdown immediate
  SQL > startup mount
  
  
  ^^
  I saw once on the google site a syntax as above. I was under the assumption that, for alteast disks 2 ASM are required (assuming normal redundancy); But here we can see one disc is defined.
  
  Sorry, I don't have an ASM Setup to test this, so would you need advice from people.

  By default, ASM tries to create a normal redundancy disk group. Therefore, he expected to have at least 2 groups of disks.
  But yes, even with one disk, you can create a disk group, but you must expressly state that it will be external redundancy.

  ++
  Connected to:
  Oracle Database 11g Enterprise Edition Release 11.1.0.7.0 - Production
  With partitioning, OLAP, Data Mining and Real Application Testing options

  SQL > create diskgroup abc disk ' / dev/raw/raw6 ";
  create diskgroup abc disk ' / dev/raw/raw6.
  *
  ERROR on line 1:
  ORA-15018: diskgroup cannot be created.
  ORA-15072: command requires at least 2 groups of failure, discovered only 1
  +++

  +++
  Connected to:
  Oracle Database 10g Enterprise Edition Release 10.2.0.1.0 - Production
  With partitioning, OLAP and Data Mining options

  SQL > create diskgroup abc disk ' / dev/raw/raw3 ';
  create diskgroup abc disk ' / dev/raw/raw3 '.
  *
  ERROR on line 1:
  ORA-15018: diskgroup cannot be created.
  ORA-15072: command requires at least 2 groups of failure, discovered only 1

  SQL > create diskgroup redundancy abc external disk ' / dev/raw/raw3 ';

  DiskGroup created.
  +++

• I bought a mouse microsoft 4000 mobile. It came with no disk and the page, to what he tells me to go said that is down. What should I do?

  I bought a mouse microsoft 4000 mobile. It came with no disk and the page, to what he tells me to go said that is down. What should I do?

  Hello

  1. what exactly is the problem?

  I suggest you explain clearly to us the question so that we can better help you.

  To troubleshoot failures in the response to the mouse or wireless keyboard, see this link: http://support.microsoft.com/kb/838398

  It will be useful.

• Cannot start with any disk

  Hi all,

  Could someone help me because this problem is crazy drivinme!

  They gave me a pc less hard drive, disk and dvd - so I therefore sat last night and put put in a fresh new hard drive and a new drive, then I was ready to go and put XP home on.

  This is a not to do as he would entangled initialize not he manages to come up with either Grub error 17 or 22 so I double checked all settings of the bios as so far, I'm aware that I don't think I missed something... so I tried to start with - 3 other drives xp, ubcd4win, and a startup disc patition magic - and guess that soon one start you the pc it reach not to start and stay on the screen with loading GRUB error 22 Please wait please help!...

  Concerning

  GT4U

  Hi all,

  This problem was a simple solution using startup disk wizard patition and rebuild the M.B.R - master boot record.

  Concerning

  GT4U

• Need help with replacement disk on port 0 in Raid1 desktop machine

  I have a HPE 380 t. I have has a RAID1 (mirror) with 2-500 GB Western Digital. When I boot it says the raid has deteriorated and an error has occurred on the player connected to port 0, port 1 player shows ok. It's in the Manager of the Intel Matrix Storage Manager, (Ctrl + I on startup). The machine starts again, but I want to replace the drive on Port 0 with another disk of 500 GB.

  How can I go on that so I don't toast all data on the drive Port1?

  I searched links and other places for help on this but nothing helps! Is there a tutorial or step by step instructions somewhere that I can go?

  Thanks in advance

  Hi Mike,.

  Lucky for you that you are using non-RAID 0 and RAID 1 or your table would probably unusable.

  You can determine the status of your RAID configuration using the Intel Rapid Storage Technology (IRST) software.  If you do not have this software on your PC, then you can Download IRST from the Intel web site.  I recommend that you use the latest version available from Intel.  General information can be obtained from the TSRI User Guide.  When you launch TSRI, help topics are an excellent source of information.  You can access TSRI by going to the control panel and select Intel Rapid Storage Technology. You can also access TSRI from low location of the taskbar.  TSRI should resemble a hard disk icon and it normally has a green check mark.  By default, TSRI is defined as delayed start, so don't expect to see active immediately.

  1. Launch the IRST while under Windows
  2. Click Help
  3. Click on troubleshooting
  4. Click on gradient volumes and follow the recommendations. Scroll to RAID 1.

• My pcdid not equipped with any disk but has a recovery partition. How can I get vista to reinstall

  can I burn the recoery CD?

  Read the General information below on the recovery of Partitions and recovery discs and contact the manufacturer of your computer.

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon.

  Mick Murphy - Microsoft partner