WLAN 4402 for Radius Authentication

Similar Questions

• RADIUS authentic works not 3560

  Hello world.

  The switch's config for RADIUS authentic.

  When I try here is the log

  % SSH-SSH2_USERAUTH 5: 'xy' authentication SSH2 Session 192.168.x.x (ATS = 1) using crypto cipher "aes256-cbc" hmac "hmac-sha1' Failed

  What should I check now

  Concerning

  Mahesh

  You must post a few outings until I'd suggest something. If SSH works very well with the local database which means the keys RSA are fine.

  If you can't attach the executed full show. Attach the bottom of the outputs listed in your next reply.

  See the race | in aaa

  See the race | Please line vty 0 4

  Debug RADIUS

  Debug aaa authentic

  Debug aaa approval

  The radius, if any server error.

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• RADIUS authentication for the switch using ISE

  Hi guys,.

  Someone did he do Radius Authentication for switch cli connection using ISE?

  We did it in our environment with ISE, but it is a challenge to give read-only access / Priv-1.

  If some users know the enable password, they can use and earn full privilege.

  Anyway to get around this other than to change the enable password?

  We have thousands of switches and won't change on each of them.

  If you have another method please advice.

  Thank you in advance.

  Well, you can set the "enable" function also be controlled via the AAA server with the following command:

  AAA authentication enable... This way server AAA will be checked for authentication for the secret to activate and use the local database as a last resort

  I hope this helps!

  Thank you for evaluating useful messages!

• WAAS for RADIUS and Windows Server 2012 NPS server configuration

  I have trouble getting our WAAS to authenticate devices and connection via RADIUS.  Running NPS on Windows Server 2012.  Confirmed that my device WAAS can ping the IP address of the RADIUS server.  Using the attribute Type of administrative service under network policies.  Look in the event viewer, I get an error with event ID 15, "a malformed RADIUS message has been received of the xxxx-WAAS-01 customer. The data is the RADIUS message. »

  Right now, I can connect with only the local default user and password name.  Here are a few config for WAAS, running version 6.2.1:

  RADIUS server key *.
  Server RADIUS auth-host 10.194.10.13 port 1645
  !
  connection of local authentication enable secondary
  enable login authentication RADIUS primary
  local authentication configuration enable secondary
  Service radius Authentication configuration Select primary
  failover of authentication server unavailable

  I confirmed that my shared key is entered correctly on the WAAS and the NPS.  I have the switches/routers Cisco works well on the same RADIUS server.

  Someone had a bit of luck plug their WAAS to RADIUS devices using Windows Server 2012 and NPS?  If so, please share additional measures you have taken to get things to work.

  Hi Paul,.

  Based on the RADIUS error you probably experience failure CSCva14731. This was discovered with Cisco ACS, but can affect other RADIUS servers.

  To confirm, you can check the corresponding error in syslog WAAS:

  authenticate: % WAAS-UNKNOWN-3-899999: pam_radius_auth: talk_radius: RADIUS server did not respond (timeout 5 (sec))

  Also, this defect would not affect peripheral on software 5.x WAAS.

  The problem will be solved in 6.2.3 to come free.

• RADIUS authentication

  Hello world

  I want to implement RADIUS authentication for my companies Cisco devices. Could someone give me some examples of configuration of how to point my switches and routers on a RADIUS server, and also to try RADIUS authentication. Only by using a locally configured account if RADIUS fails?

  My undertsnading would be to use the following configuration;

  AAA new-model

  AAA authentication login default local radius group

  start-stop radius group AAA accounting network default

  RADIUS RADIUS-server host 1.1.1.1 key auth-port 1812 acct-port 1813

  RADIUS server retransmit 3

  Thanks in advance,

  Dan

  Hello Dan,.

  your configuration seems to be OK...

  more information you can find here

  http://www.Cisco.com/en/us/products/SW/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca7ab.html

• RADIUS authentication question

  Hello world

  I'm learning the Radius Authentication. Here are my updated laboratory in place:

  R1 (107.107.107.10)-(107.107.107.4) - WIN2008 (RADIUS SERVER)

  Here is the config of RADIUS on the R1:

  AAA authentication login default local radius group

  RADIUS-server host 107.107.107.4 auth-port 1645 acct-port 1646
  key cisco RADIUS server

  I have a few questions:

  (1) above, I do not specify encryption on R1, R1 will use this as the default encryption?

  In the attached file, we see the password is encrypted, but there is no config on R1 to use particular encryption

  (2) we also see "authenticator", which is I think is R1 host name i.e encrypted with the shared secret. I'm wrong?

  Much appreciated and have a great weekend!

  Hello

  The Protocol Radius encrypts the password for the default user. I think that Radius uses MD5.

  The authenticator is a random string generated by the client and is used in the encryption of the password process.

  Thank you

  John

• 5.2 ACS with different RADIUS authentication servers

  Hello

  I want to migrate from ACS ACS 5.2 4.1. I have already configured authentication GANYMEDE +, but now I've stuck to the RADIUS authentication for remote access WebVPN configuration. Please see the following diagram:

  

  I want to configure ACS to use Server Token WBS first. If authentication fails or the user is not found, ACS must use IAS in Windows Server. If this server fails also ACS must use internal DB. Additional attributes as belonging to a group or ACL downloadable should be taken from internal ACS DB.

  Is it possible to configure ACS like that? ACS 4.1 it is very easy to configure by selecting the per user authentication method.

  Thanks for your help!

  There is an option in the Advanced tab of definition 'RADIUS Identity server' th:

  This storage of identity differentiates between 'authentication failed' and 'user not found' when an authentication attempt is rejected. Among the options below, select how a rejection of authentication of the identity store must be interpreted by FAC for the politics of identity of treatment and reports.
  Releases to treat as 'authentication failed' treat dismisses them as "user not found".

  In order to continue in the sequence, I think you have to select the option "user not found".

• Using CHAP with RADIUS authentication

  Hello

  I configured a Cisco 877 router to send the RADIUS requests when a user connects to the console (Console line) or VTY Line using the following configuration:

  AAA new-model

  Group AAA authentication login default RADIUS

  Group AAA authentication ppp default of RADIUS

  RADIUS-server host 10.0.0.1 auth-port 1812 acct-port 1812 mysharedkey key

  When I connect the RADIUS packets I see the Cisco router sends the initial AccessRequest using PAP.

  How can I configure my router to send it's original AccessRequest package with CHAP?

  My apologies if this has already been discussed, I searched high and low for an answer.

  Thanks in advance.

  John

  Hi John,.

  PPP connection supported by CHAP because a configuration command to activate the CHAP protocol as Protocol of stimulus / response. However, the Console VTY connections and to THE will always go on PAP when using RADIUS authentication. There is no command to activate the CHAP protocol for these types of connections.

  Best regards.

• VPN Site to Site Secret shared and can co-exist RADIUS authenticated VPN?

  Hello

  I have a setup VPN site to site between two offices on 515Es PIX (v.6.2 software) and has recently added a vpngroup/shared secret based VPN remote access to one of the offices. Given that just forced me to add a number of different policies to my existing crypto card, it was a plant direct and easily implemented. For more security, I want to use a RADIUS server to give to each remote user their own connections and profiles rather than a group on all password is configured. To do this, however, it seems that I have to add the following additional commands to my existing crypto card:

  client configuration address map mymap crypto initiate

  client card crypto mymap RADIUS authentication

  These do not correspond to the policy number (my site-to-site is 10, and remote access policy is political 20), so I don't know what the effect would be if I added the. It would cause my connection from site to site for authentication RADIUS request (a very bad thing)? If so, do I need another interface to bind a new encryption card to? The answer to this would be greatly appreciated!

  Also, if anyone knows an example configuration for a similar configuration, I can look at, please let me know! Thank you.

  -A.Hsu

  For the site to site connection, you change line isakmp keys and add the parameters of "No.-xauth No.-config-mode" at the end of this one, which tells the PIX not to do the auth RADIUS or assign an IP address, etc. for the specific site-to-site tunnel.

  Example of config is here:

  http://www.Cisco.com/warp/public/110/37.html

  Note that there is no command options I have just said, I just sent an email to the web guys to fix this. Basically, your config will look with the options "No.-xauth No.-config-mode" on the line «isakmp x.x.x.x key...» "for LAN-to-LAN tunnel.

• Spectrum: Intel WLAN Driver for Windows 10

  I hope this isn't a disaster in the making.  Recently, I've had this laptop and have tried to keep everything up-to-date.
  I noticed it says to install two updates - we did it, we failed.
  The update that failed is titled "Intel WLAN Driver for Windows 10".  I tried to install this update several times now without success.

  Anyone has any advice on this subject?
  
  I thank you for your time and have a good day.

  Please try to install this driver provided CV... sp74902.exe (Intel Wireless LAN Driver)

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Win XP 64 bit WLAN dirver for Satellite A300-243

  Hello

  I'm not able to get the WLAN driver for XP 64-bit.
  I see that the card is the 1394 network adapter.

  There are also a lot of pilot missing for XP 64-bit.
  Where can I find it.

  Thank you
  Oliver

  Your laptop supports the Intel WiFi Link 5100AGN wireless network card.

  Win XP 64 bit is not really popular and many manufacturers didn't release 64-bit Win XP drivers, but I think you should look for on the Intel page and I think you would find a compatible driver for this WLan card.

  Check it out and post a comment if you find a good pilot.

  See you soon

• Satellite Pro L450D-need fix WLAN Driver for XP

  I put Windows Xp on Toshiba laptop Satellite Pro L450D with drivers... The only driver I'm not 100% on is the Wlan driver for xp so I can use it wireless...
  Could someone please send me the correct link please... I now use a driver but I keep losing the connection now and again...
  Which wlan card would be in this laptop as well... Thanks in advance...

  > I have other computers here who have windows xp who have no problem to stay online wireless so its nothing to do with
  You can compare two identical OS and hardware to be objective with these comparisons identical books.
  You use the original WXP recovery disk you got with your laptop?
  Have you noticed the same behavior with Win7 you have with your laptop?

• A web service for windows authentication

  Hello
  I have a number of web services on a windows server.
  These web services are for a program client (in vb.net), access and retrieve data.
  This client program are launching for the PC of the individual user.
  The above configuration is in a windows domain.
  Currently, web services allow anonymous access. This means that anyone in the Organization, with the correct URL is able to trigger the web service.
  We are asked to remove anonymous access and all forms authentication configuration.
  Questions

  1. What is the best practice for configuration for a web service for windows authentication.

  2. We also have a couple of unix servers. They are required to access the web services (with the correct authentication). How can I get a cross-environment configuration?
  Thanks in advance.

  Hey Wee Hoe Chiang,

  The question you have posted is related to Windows Server and would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the support you want.
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  I hope this helps.

• HP R249TU - product # L2Z88PA: need Windows 7 (64 bit) wlan driver for HP R249TU - product # L2Z88PA

  Urgent need for Windows 7 (64 bit) wlan driver for HP R249TU - product # L2Z88PA.

  I tried to install both of the pilots by (http://support.hp.com/us-en/drivers/selfservice/HP-15-r200-Notebook-PC-series/7486447/model/7748033#...).
  But both atheros and broadcom is not installing.

  Hello

  Installs:

  Realtek RTL8723BE wireless

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66190.exe

  Also you may need:

  Realtek RTL8723BE driver Bluetooth

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66329.exe

  Kind regards.

• same host for radius and Ganymede

  Hello

  can I put a host (asa for example) twice in the acs Server? one for Ganymede to grant administrators access exec and the other for radius authenticate remote users.

  I don't want remote users to be able to get exec mode.

  Or how should I configure this?

  Yes, you can do it. Network configuration ON acs

  Add

  ASA---> 10.1.1.1---> Auth using Ganymede +.

  ASA1--> 10.1.1.1---> Auth using RADIUS

  Host name cannot be the same.

  Kind regards

  ~ JG

  Note the useful messages