WLC cli command "sho memory summary" displays free memory in 2%

Similar Questions

• EEM CLI commands do not run

  I'm new to scripting, SLA and EEM and went through the forums and documentation for a couple of days now to learn what I can.  I can't get my applet event handler to trigger a reason any.  I get the following syslog message based on my reaction als ip config:

  4 August 21:25:13.915: % RTT-3-IPSLATHRESHOLD: IP SLAs (100): threshold has occurred for timeout

  My setup is less than

  !

  !

  ALS IP 100

  2.2.2.2 - echo ICMP-source 1.1.1.1 ip address

  threshold of 1000

  timeout of 1000

  frequency 1

  calendar of sla IP 100 now start life forever

  reaction-configuration IP SLA 100 respond timeout threshold type 2 5 - type of action trapOnly xofy

  !
  !

  Event Manager applet ipsla-ploss

  PROACTIVE WAN PACKET LOSS SCRIPT description

  event ipsla operation id 100 reaction type timeout

  command action 1.0 cli 'enable '.

  Action 1.1, "conf t" cli command

  Action 1.2 cli command "ip access-list standard bgp-itineraries-in."

  action 1.3 cli command "5 deny 5.5.5.5".

  action 1.4 cli command "6 deny 6.6.6.6".

  Action 1.5 cli command "end".

  !

  !

  Any help is greatly appreciated!

  Add the following to your config:

  logging of IP sla

  activate the IP sla response alerts

• CLI command to set the power of 1231

  Anyone know the CLI command to fine-tune the power on a 1231 AP?

  Hi Timothy,.

  Maybe it's what you're looking for;

  local power

  Use the command from the interface of local configuration to configure the access point or bridge of power level of radio. No form of the command to restore the default setting. On the 2.4 GHz radio 802.11 g, you can define orthogonal frequency Division Multiplexing (OFDM) power levels and levels of power complementary Code Keying (CCK). CCK modulation is supported by the devices 802. 11B and 802.11 g. OFDM Modulation is supported by the 802.11 g and 802. peripheral 11A.

  Radio 2.4 GHz Access Point (802. 11 (b)

  [No] local power {1 | 5 | 20: 30 | 50 | 100 | maximum} 3

  Radio 2.4 GHz Access Point (802.11 g)

  [No] power local cck {1 | 5 | 10 | 20: 30 | 50 | 100 | maximum} 1

  [No] power local cck {-1 | 2 | 5 | 8 | 11: 14 | 15 | 17 | 20: maximum} 4

  [No] ofdm local power {1 | 5 | 10: 20: 30: maximum} 1

  [No] ofdm local power {-1 | 2 | 5 | 8 | 11: 14: 17 | maximum} 2

  5 GHz Access Point Radio (801.11 a)

  [No] local power {5 | 10 | 20: 40 | maximum} 1

  [No] local power {-1 | 2 | 5 | 8 | 11: 14 | 15 | maximum} 2

  [No] local power {-1 | 2 | 5 | 8 | 11: 14 | 15 | 17 | maximum} 2

  Note the maximum emission power depends on your regulatory domain and the antenna gain for your access point or bridge. For more information see the "Channels and antenna settings" section of the installation guide hardware for your access point or bridge.

  --------------------------------------------------------------------------------

  --------------------------------------------------------------------------------

  Note the supported transmit power levels on the various points of access and bridges.

  --------------------------------------------------------------------------------

  --------------------------------------------------------------------------------

  Note This command requires radio to be turned on and activated to determine valid power settings allowed on your access point radio.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/products_command_reference_chapter09186a00804e631f.html#wp2459939

  I hope this helps!

  Rob

  Remember messages useful rate...

• Cisco ACS 3.1 and Logging of Nortel Passport CLI commands

  Good afternoon

  We try to log commands CLI Cisco ACS version 3.1 of Nortel Passport 8600. The version of the code that runs on the Passport does not support Ganymede +.

  Passports authenticate OK but don't sign any order information. I "think" the problem is maybe that the VSA Radius of Nortel for cli-commands-attribute, 195, is not collected by ACS.

  Does anyone know how I would go to get this added to the existing list of Radius (Nortel) VSA?

  Thank you very much

  Kind regards

  Flett.

  Foisy,

  You must add the attribute Nortel 193-195 to activate the posting of the order.

  Unfortunately you can't download on code 3.x, you will need to upgrade acs to the 4.x code.

  Kind regards

  ~ JG

  Note the useful messages

• How to put power on and off through CLI command in ESX Server

  Hello

  We are facing a problem with VI Client members in VCenter or individual ESX servers.

  In this case how properly turned off (or) power on virtual machines through CLI command on the ESX Server.

  Any command available for this case.

  Kind regards

  Eric

  On PowerCLI: Take a look at vSphere PowerCLI Administration Guide

  Shutdown-VMGuest and Start-VM cmdlets

  On vSphere RCLI take a look at vmcontrol.pl

• What is the CLI commands

  What is the CLI commands to monitor a router interface (800 series) 'live '? Watch the increment of packages.

  I have provided links to the appropriate documentation. First you will need a basic understanding of the command line Interface (CLI). Then, you can use the commands to enable Capture of integrated package.

  Using the command in the Cisco IOS software command-line Interface

  Cisco IOS embedded packet Capture

• 1131AG CLI commands

  I try to reset an ap on its values. I can't enter in the cli, but the "Clear wr" command is not available. How to clear the config on this access point?

  Also, I have configured initially access point to connect to wlc 4400, which worked great, but when you try to reconfigure the IP address of the CLI is not an option, because the command is disabled.

  How to display the running-config on the ap?

  This access point can be used as a standalone ap?

  Thanks in advance.

  Hi Carlos,

  Once that the AP has been converted to LWAPP (to work with the WLC) the ability to use the CLI interface is mainly lost. Here is the method to return to autonomous (so it can be used as stand alone);

  Returning to standalone Access Point

  It is possible to return to a point of access compatible LWAPP Cisco Aironet return to autonomous mode. Please refer to Cisco Aironet Lightweight mode standalone update Access Points to get detailed instructions on the returning to stand-alone mode. Use this URL

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  Convert a standalone Lightweight Access Point

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  Here's the info CLI;

  Manually configure the controller information using the CLI of the Access Point

  This doc.

  http://www.Cisco.com/en/us/products/ps6521/products_installation_guide_chapter09186a008079b730.html#wp1082991

  I hope this helps!

  Rob

  Remember messages useful rate...

• STROKE (Application Visibilty Control) on WLC 5508 7.5 do not display data

  Dear all

  My WLC has problem...

  the STROKE is not display data (graphic or otherwise)

  I have already set up two Wlan id with the visibility control, but two of them do not display data...

  Here is my setup place WLC 5508...

  My WLC running on OS 7.5

  pack 1.0 protocol version

  NBAR engine 13.0

  AUS 6.0.182.0

  Cisco controller) > see the version of the Protocol-pack stroke

   

  Protocol STROKE Pack name: Protocol Advanced Pack

  Protocol STROKE Pack Version: 1.0

   

  (Cisco Controller) > show stroke engine version

   

  Version of the engine STROKE: 13

   

  (Cisco Controller) > show sysinfo

   

  Name of the manufacturer... Cisco Systems Inc..

  Product name... Cisco controller

  Version of the product... 7.5.102.0

  Bootloader Version... 1.0.1

  Retrieving Image Version field... 6.0.182.0

  Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27

  even from CLI still do not display data

  (Cisco Controller) >Show stroke statistics upstream applications top

   

  Perspective of the STROKE is 0 for all applications.

  MISTLETOE on attachment configuration capture

  Need your advice is there any configuration that I miss... ??

   

  As long as you go to the STROKE centre should work in Flexconnect. You can check the AP mode under wireless > click on any access point.

  http://www.Cisco.com/c/en/us/support/docs/wireless/5500-Series-Wireless-...

• Darwin.CLI: most of the cli commands is not available

  Most of the command-line to point 6.1 does not for example to vcloud led application 6.1

  
  list-cloud-tunnels' was found but is not currently available (type 'help' then ENTER to learn more about this command)
  

  Spring > create cloud tunnel

  Command "create cloud-tunnel" was found but is not currently available (type 'help' then ENTER to learn more about this command)
  Spring > cliversion
  vCloud Automation Center Application Services CLI 6.1.0 BUILD - 2064245
  Copyright (c) 2011-2014 VMwareInc. All rights reserved. This product is protected by the U.S.
  and the international laws of copyright and intellectual property.
  VMware products are covered by one or more patents listed in the http://www.VMware.com/go/patents
  Spring > display user

  
  "View user" command was found but is not currently available (type 'help' then ENTER to learn more about this command)
  Spring > list-cloud-tunnels
  'List-cloud-tunnels' command was found but is not currently available (type 'help' then ENTER to learn more about this command)
  Spring >

  Thanks for your help, you are right, but I didn't know how to do it. the documentation could be updated to reflect the it. Here's how I work.

  Login serverUrl- https://**.**.**.**:8443/darwin - [email protected] - password username *-tenantId tennantnamehere

  Thank you

  Niasse

• CLI command (or script) to determine if a resource pool has enough resources to a virtual machine

  Is there if a VMS resource pool has enough resources available to start the virtual machine WITHOUT triggering an error of vSphere PowerCLI script - or a series of commands - which can be used to determine?

  For reasons of performance test, we use a pool of resources with maximum rates for RAM and CPU.  Each virtual machine in the pool has a reservation for CPU and RAM.  Test automation will try to start VMs as much as possible in the pool during the test.  The CLI will return an error when you start the virtual machine may exceed the amount of allowed resources.  When this happens, an error on the console vSphere "insufficient resources".  Instead of constantly from the virtual machine, fault and generates error - is there a way to check to see if there is enough space?

  Thank you

  Jason

  Hi Jason,

  You can try if the following PowerCLI function is what you need. The function does not resemble stretch bookings.

  function Get-VmStartPossible {
    param($VM)
  
    $VM = Get-VM $VM
    $ResourcePool = $VM | Get-ResourcePool
  
    $CpuReservationUsed = $ResourcePool.ExtensionData.Runtime.Cpu.ReservationUsed
    $VMCpuReservation = $VM.ExtensionData.ResourceConfig.CpuAllocation.Reservation
    $ResourcePoolCpuLimit = $ResourcePool.ExtensionData.Config.CpuAllocation.Limit
  
    $MemoryReservationUsed = $ResourcePool.ExtensionData.Runtime.Memory.ReservationUsed
    $VMMemoryReservation = $VM.ExtensionData.ResourceConfig.MemoryAllocation.Reservation
    $ResourcePoolMemoryLimit = $ResourcePool.ExtensionData.Config.MemoryAllocation.Limit*1MB
  
    if (($CpuReservationUsed + $VMCpuReservation -gt $ResourcePoolCpuLimit) -or ($MemoryReservationUsed + $VMMemoryReservation -gt $ResourcePoolMemoryLimit))
    {
      $false
    }
    else
    {
      $true
    }
  }
  

  You can call the function with:

  Get-VmStartPossible -VM MyVM
  

• Command & Conquer is not displayed correctly.

  Original title:

  RED ALERT 2

  I scoured the internet for a solution to this problem, but finally I found no, so I now look forward to Microsoft technical support.

  I have the game Command and Conquer the first decade of the value. I am well aware that EA has launched this pack at the Golden time of XP, so technically it is not supported by Windows 7 or 8, but I won't give up as I've had them before work. My computer is a Dell Inspiron 7010 processor i5 with Windows 7 X 64.

  To start, I went the installation process. By running the installer as administrator for Windows XP SP3, they installed without problem from the disk. The old C & C (up to RA - 1) games work fine. Generals had a problem at the launch of her, but I found a patch that fixed. Red Alert 2 is loads different well that-it up and works very well, but it is missing parts of the menu-it does not display some component video for me. I would like to provide a screenshot, but all my screen capture software is able to 'see' videos somehow I can't and displays and buttons, as they should. Now, I know the layout of the menu, so I can't get into the game itself, and it plays very well most of the time - with only a few missing elements, which appears once again to my screen capture software, but not on my screen. This is a common bug for this game and seems to affect only the newer computers, 7 and 8. My brother has this game on his old HP laptop running Windows 7 X 32, and he managed to solve this problem by changing a few settings .ini. I tried it myself without success, and after tinkering with the compatibility some more, did not find the answer to this problem. It is clear that the game works well on Windows 7, but it does not display properly.

  That said, I welcome any assistance from the community of Microsoft! Thank you in advance!

  Wow, that was fast.

  Well, then everything through a wire dead on Tom material, I found a link to a YouTube video. It is long and a bit hard to follow, so I'll save you all the trouble. The problem with the buttons is on the screen and for some reason weird needs of Windows 7 (and 8, hopefully will find soon) this second weird monitor added to make it work.

  Go to 'Screen Resolution' and click on "detect" - then appears open, put in place a new monitor in the #2 (or whatever the accommodation is planned) using all the default graphics card is for your machine. Mine is a laptop, so I had a choice - I doubt it would make much of a difference, what graphics card you choose, but this guy would recommend grabbing one "default". Once you have done this, say the new view to go via the VGA input anyway, then save it. Once it is ready, select the 'new' view and select "Display Extend" under settings. The screen will panic for a second, and then ask you to save the changes-do that and you're golden.

  The thing about this difficulty that upset me, is that it is easy and totally weird. I have no idea why it suits it. I have no idea why he did what he did. It works well - for red alert 2 Yuri revenge both. I hope this will help someone and another not go review the problem I experienced just!

  For those of you looking for a check step by step, this video out of the guys. Be forewarned, it is long: https://www.youtube.com/watch?feature=player_embedded&v=hojMNk93PoU

  Good luck!

• For AP in FlexConnect CLI commands

  Hello world

  Just as the title says, as much as I Googled it I can't seem to find what are the CLI for AP in FlexConnect commands

  I know that we can telnet/ssh to the AP in flexConnect, but what are the possible commands that we run on the AP?
  Hope someone can help :D

  Thank you!

  This can be useful if you do not see it

  http://www.Cisco.com/en/us/docs/wireless/controller/7.4/command/reference/Flexconnect/flexconnectcr74.PDF

  HTH

  Rasika

  Pls note all useful responses *.

• need for WPA2 Personal Mode CLI commands

  I saw this example but I need the CLI generates the GUI. Can anyone help please?

  https://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml#pers

  That's what I have to do without the GUI on a 1142N 12.4 running

  Configure in personal Mode

  The term made personal mode refers to products that are tested to be interoperable in mode PSK only of operation for authentication. This mode requires manual configuration of a PSK on the AP and clients. PSK authenticates users via a password or code identification, both the client station and the AP. No server authentication is required. A client can access the network only if the client password matches the AP password. The password also provides the numbers that TKIP or AES uses to generate an encryption key for encrypting data packets.       Personal mode is intended for SOHO environments and is not considered safe for enterprise environments. This section contains the configuration that you need to implement WPA 2 in personal mode.

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  Hello

  Here are the commands for WPA2 personal mode CLI

  Configure the terminal

  dot11Radio interface 0

  encryption ciphers aes - ccm mode

  or

  encryption mode vlan ciphers aes - ccm< ---="" if="" you="" have="" multiple="">

  output

  dot11 ssid

  open authentication

  authentication-key wpa version2 management

  WPA - psk ascii

  Kind regards

  Madhuri

• Command delay AppleScript in display-asleep

  Hello

  I would look for a way to run a script at midnight - NOT on a calendar. For example, I want to do the following:

  delay 10000 -- assuming 10000 seconds to midnight

  activate the application "Notes".

  tell application "System Events" to keystroke "Test"

  The problem is that when my display sleep (the computer is not sleep), the delay control is stuck. Any help is greatly appreciated. Thank you!

  Are you really sure you want to exit a script running & hope that it will work?

  Personally I would forget about the timer, set the script to be triggered by a calendar event instead.

  1. Save the script as an Application in the Applescript Editor.
  2. Add an event to the time you want in the calendars, set an alert, with "Open File at the time", choose custom: & add your script.

  I think that the calendar will be reliable Mac hoping moe keeps the running script, it can wake the Mac - I test only.

  Calendars also makes it very easy to reschedule.

• Confirmation of these CLI commands...

  Given that I have no development environment, and I only have switches production, is - anyone can confirm the function of these commands?

  I have VLAN 10, 20, and 30 defined operation:

  config said-> "vlan 10,20,30.

  I want to * add * 40 and 50.   Is a supercargo command another, or is it a true ADD?

  If I run it, "vlan 40,50" will be the config now say, 'vlan 10,20,30,40,50"or will my order supercargo what existed, where now the config looks like,"vlan 40,50? (where the existing VLANs will disappear)?

  **************************************************

  Second: Same question with the addition of VLAN to a port channel.

  My current config has VLAN 10, 20 and 30 on a port channel:

  config-> vlan allowed switchport General add 10,20,30

  If I add 40 to 50, it is a true ADD, or made an order existing supercargo?   When I run it, 'switchport general allowed vlan add 40,50' resulting?

  config->

  "vlan allowed switchport General add 10,20,30,40,50" (an ADD-ON)

  or

  "vlan allowed switchport General add 40,50" (a supercargo)

  If the config would say then that you question, "vlan 40,50", "vlan 10,20,30,40,50".» The commands add the VLAN to the config. They do not replace the VLAN already configured.

  When you issue, 'switchport general allowed vlan add 40,50' ' switchport general allowed vlan add 10,20,30,40,50"sera the result."