WMC and RF remote, "do not detect the IR receiver.

Similar Questions

• After a clean install of Windows Vista, Intel Wifi card is installed and activated, but does not detect the network.

  Wireless card not working after a clean install of Windows Vista

  I did a clean install of Windows Vista Home Premium on my HP Pavilion of 32 bits. I've completely updated Windows via Service Pack 2. Given that the clean install, my wireless card, Intel (r) Wireless WiFi Link 4965AGN, was not able to detect all the networks. The Wifi card is listed under NICs as being installed and activated. the hardware on my laptop Wifi switch is set on "on" and the light is blue, indicating that the card is working.

  I can connect to the internet if I connect physically my computer to the modem with an ethernet cable wireless, so the modem isn't the problem. Other computers can connect to the wireless modem, so my Wifi modem functionality is not the problem. The problem with my computer.

  I tried to uninstall the Intel driver and reboot my computer with the generic driver. Install the driver generic, but my wireless card has not always worked. I then ran an update of windows, nothing helps.

  I tried to install the "Intel® PRO /? Wireless and WiFi Link"drivers for Windows Vista (32-bit 13.1.1.1 the latest version and the previous version 12.4.4.5 32-bit) for the Intel® Wireless WiFi Link 4965AGN directly from the Intel Web site at http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+WiFi+Products&ProductProduct=Intel%C2%AE+Wireless+WiFi+Link+4965AGN. The map didn't always work with a driver.

  In addition to the pilots, I also downloaded a tool of diagnosis of Intel (Intel® PROSet /?) Utility of WiFi wireless connection for Windows Vista 32 -? Bit). Said diagnostic tool the WiFi card is not installed or enabled, however, Device Manager maintains that he is also installed and active.

  Is there a problem that causes Device Manager to say that all is well with the card, but does not map to realize that they diminish the radio signals? Everything's fine, diagnostic, it just does not detect networks around him. Help, please.

  Hello

  The on/off switch actually works?

  Since it is an internal adapter to ensure it is enabled in the settings of configuration/F2 (BIOS/CMOS) often like you
  Start - so look at the screen.

  Have you tried the computer on other WiFi networks? You had a WiFi type problem before the
  Re-install of Vista?

  ---------------------------------------------------------------------------------------------------------------------

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Qosmio F10: Driver Installation does not detect the wireless network card

  I wonder if anyone can help before I phone supported again. My motherboard is dead and ASP replaced and recovered my laptop qosmio F10. Since having back, my wireless card did not work.

  Windows detects a "network controller" whenever it starts and gives me the opportunity to install it. I tried to install it by navigating in the 'tools and utilities' records CD rom for folders and subfolders of "Wireless network driver" and it still does not detect the card.

  I also tried to install using the cd rom web gui and selected the 'Pilot wireless network' link and then tried to install it. It opens a dos command prompt and try to install but comes up with the error "failed installation.

  I ran the customer service and they told me to run the qosmio recovery/then recovery of product/recovery of qosmio and again...

  I still don't the card wireless not yet installed. This happened to someone else?

  I tried already shot the drivers from the web, but with no luck... If a representative of customer service with the help of good technical knowledge that would be great, or if someone has encountered the problem too and he had fixed to the give me some advice...

  Thank you very much

  Sean

  Hello

  you see the card wireless as an unknown device in Device Manager? If this is not the case, perhaps that the card was not properly installed after replacing the motherboard.

  Sorry I have no other idea.

  Good bye

• Windows XP missing HAL. DLL file. CD ROM does not detect the Windows XP installation CD.

  I received the error message to the Windows startup, that I need to replace my Hal.DLL file.  I can't access a safe mode with command prompt, and CD rom does not detect the CD. I have rebuilt the Boot.INI file and still no luck. I tried to put HAL. DLL on a flash drive, but it cannot read it for some reason any. "Cannot develop"...

  Any help would be appreciated!

  Go to the store and buy an optical drive. They are very expensive. No, you cannot use the optical drive of your laptop. You can possibly create a bootable USB key with a distribution of Linux on it and copy the correct boot hard disk files. I say "may" because not all older computers can boot from a USB device. Look in your BIOS to see if your computer has this capability. If he can:

  http://www.pendrivelinux.com

  If you have not backed up your data, then you have trouble. While you're at the store also buy an external hard drive. You can start the computer with a Linux Live CD (in your new optical drive), and copy the files on the external hard drive. Then you can continue to try to repair your computer.

  MS - MVP - Elephant Boy computers - don't panic!

• can not detect the iphone after upgrading 12.5.1.21

  Set to update to the latest version of itunes (12.5.1.21) and now itunes does not detect my iphone.  tried to remove the lockdown folder. tried to restart all devices.

  Windows 10 with all updates installed. Someone at - it suggestions?

  If your iOS device does not appear in iTunes, try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  To step 3 above, open the Device Manager. Expand one of the articles that are listed.

  • USB Bus controllers
  • Imaging devices
  • Portable devices
  • Other devices

  Plug in the appliance. You should hear the telltale Windows sound device connection and a Division must acquire a new entry. This should be your device. It cannot be labelled properly at this point. If you do not hear a suspicious noise cable damaged.

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support Apple version of the above opinion.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates. 64-bit users might also try the alternate build Download iTunes for Windows (64-bit-for older video cards) , which is sometimes a useful workaround.

  Or try to go back to the last version of iTunes that has worked for you. See the programs installation of iTunes to download links. If you're back 12.5.1.21 to 12.4.3.1 or 12.4.2.4, for example, then you will also need to restore the database of the library using the method described in the empty/corrupted after upgrade/crash iTunes library. The tip makes suggestions to reintroduce recent purchases, so at worst, you lose a few meters or a newly created playlist.

  TT2

• Does not detect the hdmi cable more (very specific scenario)

  Well then...

  Got a monitor 15-HD to hdmi cable and a mac laptop (13 in the retina).

  So when I got all that I put it all together and it worked. I left because there a little bit, everything is plugged in and did not return for some time, so my mac fell asleep at the time wherever I went. Disconnected everything to relax on the couch. I went back and all plugged together again except that now the mac does not detect the cable. Tried a bunch of things with it. Restart, unplug the unit, detection manually, etc...

  Since the monitor is used and recently purchased cable, I thought time to them to test first. Got a laptop PC and plugged into the cable. The monitor and cable worked.

  Tried to connect my mac to the TV with my ps4′s hdmi since I did that a lot before. Also works.

  The problem is literally the combination between the cable and the mac. Which is a problem since I got the reason was to serve as my mac.

  During my research, I saw that specifically leaving the connected hdmi where sleeps your laptop can spoil it supposed to be... I saw it one time so idk if it's true, but it happened to me... and no, it wasn't really a solution when I came across that. Tried Googling this specific problem, but did not meet anything since my problem seems so specific.

  Fast forward to the next day and tried again now that both had little respite between them. Plugged into the HDMI and my laptop starts fading and return to a black screen. The screen would go black usually and so the laptop screen and the monitor would appear once again. sauf_que this time that there not, he just kept it and the monitor has not changed (Yes) it's). Not wanting to let him do that too long I unplugged and tried a different port with an adapter, I have also, since I did 3 holes I could use this for might as well try them all again. But unfortunately, I don't have it trigger anything again. So I went through another round of troubleshooting to try to make it work, but here I am, trying to see if anyone else has had this problem and solved. I am back to wait another day I guess and just hope. If not idk what to do, except maybe to get another cable? I don't know if this would solve it well.

  Hello Kaida W,.

  Thank you for reaching out to the Apple of community support. I'll do everything I can to help you get your monitor works as expected. Our first step would be to restore your System Management Controller (SMC) that allows to manage systems of different material on your Mac. This article will guide you through reset:

  Reset the management system (SCM) controller on your Mac.

  Try it and tell us how it goes. The entire community is here to help.

  Best regards-

• HP Support Assistant on my laptop or desktop does not detect the other machine.

  HP Support Assistant on my desktop or my laptop does not detect the other machine.  They are both on the same network.  Both are HP machines. Both are running Windows 10.  Is normal.  I would like to kind of monitor my desktop with my laptop when I'm away from home.

  @bmedbury

  The behavior you describe is normal - the HP Support Assistant is a program "per computer", in other words, each program HPSA lies and keeps track of just a computer on which the program is installed.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• Wk2 will not detect the HDD on Portege 3480CT

  Hi all, been tring this for 2 days now and I have no idea. I want to install win2k on 3480CT but the win2k installation does not detect the hard drive... It will detect WinXP, win98 detects...

  I have the latest version of the bios, I start to think win2k is in need of a driver for the reader, but I'm not finding.

  Help...

  As mentioned for install the W2k you n t need additional drivers.
  I also recommend the HARD whole disk formatting and delete all partitions.

  In addition, you must use an original CD of Microsoft W2k. I read on the net that some people wanted to use the copy of the CD W2k, but this CD is not bootable.

• My macbook does not detect the dell wireless mouse

  I have the macbook air. I tried to connect my macbook to my Dell Wireless mouse. But my macbook could not detect the mouse

  Without a model number, we cannot exclude that particular mouse is incompatible with OSX, especially if it is old.

  OS X pair with a large number of devices bluetooth automatically, but some need to be put in pairing mode.  You will find the Dell mouse model and see if that is his business.

• 15 - ac130nia: my wifi and bluetooth is still not detectable and can also discover other wireless networks

  My WiFi and Bluetooth is still not detectable and can not find other wireless networks

  @Pelumi10Hi

  Thank you for visiting the Forums from HP Support. It's a great site for information and questions. I read your post on wireless and Bluetooth connections are not always detectable not. I'm happy to help with this problem!

  I would need more information about this to help you better.

  • It has never worked before?
  • When the problem happened everything first?
  • You did the hardware changes as obtain replaced Wi - Fi?

  Please follow these steps and check out these links to try to solve the problem.

  1. Turn on your Bluetooth device and make it discoverable. The way that make you it discoverable depends on the device. ...
  2. Click Start > type Bluetooth > Select Bluetooth settings in the list.
  3. Activate Bluetooth > select device > pair.
  4. Follow all the instructions if they appear.

  Open windows control panel, open Power Options and next to your currently selected power plan, click Change plan.  In the next window, click on change advanced power settings.  In the next window, open 'wireless adapter settings' and then open 'power saving Mode'.  Next to on battery: click on the current setting and a drop down menu will appear - select 'Maximum Performance '.  Do the same for the sector.  Then click on apply and then Ok to save the settings.

  Restart the computer and see if this contributed to the issue.

  Also open Device Manager. Go to the network adapters and expand it. Select the network adapter for your device by clicking right on wireless and click Properties. Then go to the power management option and uncheck the box that says" allow the computer to turn off this device to save power. In addition, check the box that says "Allow this device to wake the computer"

  Please visit this link to solve the problems of Wi - Fi: http://support.hp.com/in-en/document/c03535285

  There's a video associated with the problems of Wi - Fi in the link.

  You can also check these links:

  http://h30434.www3.HP.com/T5/notebook-wireless-and-networking/WiFi-connectivity-problem-in-Windows-8-1/TD-p/3951390

  http://support.HP.com/us-en/product/HP-15-notebook-PC-series/8499326/model/8942890/document/c04800801/

  To resolve Bluetooth issues problems please visit these links:

  http://support.HP.com/us-en/document/c03429630

  http://support.HP.com/us-en/document/c01060335

  To simply say thank you, please click the "Thumbs Up" button for appreciate my efforts. If this solves the problem, Please mark this "accepted solution". If you need more assistance let me know and I will gladly do whatever I can to help.

  Thank you and have a blessed week ahead!

• Qosmio G50 does not detect the connected Bluetooth devices

  The qosmio g 50 (windows vista ultimate) detects more devices via bluetooth
  Until two days ago, I pointed out quietly via bluetooth mouse. And then, do not know what is success does not detect any more.

  I did a test to see if it could depend on the PC or the mouse.

  I took the phone with bluetooth, I turned and qosmio, is not detect the phone.
  And the phone does not detect the qosmio via bluetooth.

  What checks can I make on the qosmio while ' I detect devices via bluetooth?

  Tank you

  Hello

  BT has been successfully activated on tis G50?
  Have you used the FN + F8 key secret to switch on the BlueTooth?

  Please check if the FN key works correctly, otherwise, go to the button start-> all programs-> Toshiba-> Flash Cards Support utility and restart the software.

• IdeaPad Y500 does not detect the camera

  Hello everyone!

  I had my Y500 for about 1.5 years and I can't use the camera more. The computer does not detect the camera and when I downloaded and installed the camera software the computer shows me "no approperiate driver to install! I tried to uninstall the camera driver and reinstall it again, but it's the same problem.

  I would appreciate a quick response

  The problem was with the camera and the camera cable. I sent my computer to
  Lenovo and they fixed.

• Computer does not detect the pci card

  Hello
  I have a dell dimension 4550 pc, with windows xp professional service pack 3.

  I connect to a card its pci in one of the pci slots empty of the motherboard, but when I start the computer the system does not detect the new card.

  What can I do to make the computer detect the new card?

  Thank you

  It is not clear what part to uninstall the drivers and install the good? So what if Windows installs the drivers? Uninstall them, do not restart and install the good. MS - MVP - Elephant Boy computers - don't panic!

• J4580: J4580 will not detect the alignment page.

  My J4580 that works very well for years, now will not detect the alignment page after you print and put on the scanner bed.  I try three times and it then goes to the default alignment parameters.  It still prints but text tends to little fuzzy.  What can I do to fix this?

  Hi @BruceK43,

  Thanks for joining the Forums of HP Support for a solution to your problem of alignment.

  I understand that you used a HP Officejet J4580 all-in-One printer with a Windows 10 computer but when you try to only scan the alignment page, the printer is not detected by the alignment page returns to the default alignment parameters. I would like to help with that.

  Here is the document of support designed to be used with this problem - a "alignment failed" Error Message appears on the printer control panel.

  Please let me know if that solves the problem, or if you need assistance.

• Audio input Inspiron 15 3000 can not detect the headset

  Audio input Inspiron 15 3000 can not detect the headset, but audio dell can detect something trendy. However, the playback sound device cannot detect any helmet. Now I only get gurgling in the helmet. How to solve this problem?

  Hello. To test the headphone switch the native Windows audio driver Realtek audio driver.

  1. open Device Manager (type devmgmt.msc in the box of Windows search).
  2. develop the 'audio controllers, video & game' and right click on "Realtek High Definition Audio".
  3 Select this option to "Update driver software".
  4. click on "Browse my computer for driver software".
  5. click on "Let Me pick from a list of drivers on my computer".
  6. put the "Show compatible hardware" check box if not already checked.
  7. in the list of devices, click on 'High Definition Audio"(native driver).
  8. click on "next".
  9. in the update driver warning box, click 'Yes' (the driver).
  10 restart the portable computer if you are prompted. If not invited, so no need to restart.
  [To return to the Realtek driver, do it again but reverse the names in steps 1-6.]

  If it is still bubbling even with the native driver, test by using other headphones. If still no luck then probably hardware failure. Contact technical support for warranty repair.

  If it works fine with the native driver, then the Realtek driver is buggy. Try a different version of the driver. If you need help with this answer comes back with the full model name (something like "Inspiron 11 3147", etc.) and which operating system there.