write a text file on Simulator 9800

Similar Questions

• Writes a text file from a network computer to another computer on the network.

  It is possible to write a text file from a computer on the network to another computer on the network through labview without using FTP?

  Hi bebo_lm,

  It depends on how they are connected. If you have a 'normal' access to the pc and you can write on a hard drive of the other computer, you can use the writing functions of files or the copy of the file. If they are not connected like this, then you need another service. Why you do not use FTP?

  Mike

• Error 1: Write to text file

  Hello. I get an "error 1 write to text file" in my program.

  The error occurs occasionally and I can't understand what is causing the error. What is this error? If I ignore it and press to continue the program seems to work and it stores data. The program acquires the data and records to several files. The screenshot of the error is attached.

  Thanks for the help

  I got it. I added a variable additionl to start recording only after that the name references were initilized. It was the problem of race condition, but now I know more about the labview data flow

• How to write the text file in Shockwave?

  Someone knows how to write the text file in Shockwave on the disc of the user?
  
  Thanks in advance.

  These Xtras can cause a lot of havoc when used with the intent to hurt.
  What you can do is to write with setpref and store a list of backups and the
  registers itself separately. Next, you need to build your own save/open
  dialog box for the user:
  * Choose a previously saved file to load or replace
  to create a user type the name of a new file to be saved.

  The only thing that remains is that the user can't decide where files
  are saved.

  Manno

  SiuLinda wrote:
  > Thanks a lot for your answer.
  > Yes, cookies is good, but I have to write a program to save the text file in
  > When the user wants, the user can open these files later if they like as, using
  > Filextra and Fileio, but I found that all these Xtra extensions seem to be not supported by
  > shockwave.
  >

  --
  ----------
  Manno Bult
  [email protected]

• Write/close text file problems

  There is probably a simple answer to this question, but I can't seem to understand.

  I'm using a controller compact realtime RIO 9068

  I have a program very simple reading of data from a serial port and saving it to a text file.  Before recording starts, I call the function open/create/replace file, then I start reading the port, and I run the function "Write to a text file" whenever I get a certain number of bytes from the serial port.    Everything works fine if I use the program as planned, I press the Start button to start the recording of data and then press the stop button to stop the recording, who runs then the function "close file".  I get a well recorded transcribed text file and all is right with the world.

  This application is intended to save the data for hours unattended, if I want her to be robust for a power failure.  If I pulled the power so that the data connects, I always get the file on the hard drive, but is 0 bytes is no in.  It seems that if I don't run the IA function to "close the file" nothing is saved.  I am confused because I thought the closing of the record vi relases only the file of labview control and don't actually nothing to write to the file.  Anyone have any ideas on what is wrong?

  I'll post photos of the code, but its on a machine of lab that is not connected to the internet.

  Discover the function Flush file in the Advanced queue Functions menu.  Following is the help file for this entry:

  Writes all buffers of the file identified by refnum the disk and update the directory of the file associated with refnumentry.

  The file remains open and refnum remains valid. Data written to a file often reside in a buffer until the buffer fills, or until you close the file. This function forces the operating system to write data from the buffer to the file.

• FrameScript: write to text file

  Hello comrades,.

  When I have to loop through a list of files of the book and write their names in the console of FM, the full list is displayed. However, when I write the list in a text file, 1 file name is written. No idea why?

  ForEach (BookComponent) In (vCurrentBook) LoopVar (v_File) loop

  ...

  Write v_File Console;

  vs. :

  Set vPath = v_UserPath + DIRSEP + "_" 'Test' + ".txt";

  New text file File (vPath) NewVar (vFile_Listing);

  Write Object (vFile_Listing) v_File;

  EndLoop

  Thanks in advance for your comments!

  Roman

  Hi Roman, it works for me:

  The value of sPath = "C:\DATA\Test.txt";

  New file text File (sPath) NewVar (represented);

  Set oBook = ActiveBook;

  ForEach (BookComponent) In (oBook) LoopVar (oBookComp) loop

  Write Object (represented) oBookComp.Name;

  EndLoop

  Close the file text Object (represented);

  You must close the text file when you are finished with it. Maybe that's the problem with your code.

  -Rick

• How to read and write a text file to the folder of the user preferences?

  I'm trying to code for the user to record the plug-in, the first time that the user opens Acrobat after you have installed the plug-in. I want to write a file of registration of preference of the user folder access later to check that they are already registered.

  Is there an easy way to do this? I wrote the code to access the preference of the user folder to search for the file, but I have not been able to code for the write file. All I've found is how to write a PDF file.

  Any suggestions?

  Gregory

  ASFileRead/ASFileWrite

• Write to text file - question

  How can I add on top of file .txt 'caption', for example I want in my example add "date" and "time".

  Date time

  12.3.2012 12:46:44
  

  All you had to do is put in the header before the loop. It is here, but it's in LabView 2009. Tell me if this does not work on yours.

  David.

• Write in the text file on request

  Hello

  I've been struggling with the "write to text file" in the part of the attached .vi button

  I want to be able to say my program when I press on the Boolean key it should collect 1 sample point only from the mean.vi - now that I managed to do a Boolean-button that starts the collection of data and then I have to press the button again when I 'think' now, I collected a data point using the structure of the case.

  Can someone help me to collect the data a not that when I press the Boolean?

  Thank you!

  Change the mechanical action of the key "lock when released.  It is an option to right click on the button on the front panel.

• Write to the file text File.vi out all but first line begins with tab

  The PNG attached shows the code used to accumulate strings concatenated into an array of strings for the first four lines, then to a string in the array to the worksheet String.vi and, finally, use write to Text File.vi the lower right corner shows the result in a spreadsheet. Note the 3 empty entries marked by a filled red rectangle. Examination of hidden characters shows that there is a tab at the beginning of lines 2, 3 and 4. There is no tab shown in the code. How these tabs to get? How can I stop them? I tried with the option 'Convert EOL' on and outside, without any difference. The help says that an EOL OS-dependent character is added to each line. I can't imagine that the EOL Windows character has a tab.

  The tabs are from the table to the string of worksheet function.  You build a chain of worksheet, complete with tabs and CR.  Just drag a concatenate the strings in his place and it will work.

  I would bag all constants of the tab and the CR.  Build an array of 2D with just the values strings (without tab, no CRs), happening in the array to function SS.

• How to put more than 100 acquisitions to "write text file.vi?

  Hello

  I work with labview for about a week and I need help.

  I use the "write to text file.vi" in one of my screws and now I've discovered, that the number of acquisitions in this VI seems to be limited to 100.
  but I need a larger number (around 10,000). So I need to know how to increase the number.

  If you need more information, tell me and I've got the poster!

  THX
  Fr33k

  Propably the control's properties from the beach.

  Right-click on the control and select Properties. Then go to the tab of the range.

  Felix

• UTL_FILE text file writing

  Dear all,
  
  I use the UTL_FILE to write a text file.
  

  C:=sample.txt;
  F := UTL_FILE.FOPEN('EX',C,'W');
  for I in C1 LOOP
  UTL_FILE.PUT_LINE(F,
                    I.1||'|'||
                    I.2||'|'||
                    I.3||'|'||
                    I.4||'|'||
                    I.5);
                    UTL_FILE.FFLUSH(F);
  end LOOP;
   utl_file.fclose(f);
  end;
  {CODE}
  
  When i open the txt file in Notepad , The data coming in the single line with some enter key ( Carriage val)

  sample:
  1233 | 1111 | 1111 | 1111 (square box) 1222 | 1111 | 1111 | 1111 (square box) 1211 | 1111 | 1111 | 1111
  
  
  How to remove the key enter during the writing of the text file. Or any other solution to get a notebook for the sub file condition
  

  Result needed.
  1233|1111|1111|1111
  1222|1111|1111|1111
  1211|1111|1111|1111

  Thanks in advance.
  
  See you soon,.
  San.

  Your database server is likely to be Unix or Linux, right? Which means that it uses a single character (LF) to "new line", rather than Windows that use two characters (CR - LF) to 'new line '.
  (If you open your file with WordPad instead of NotePad it will probably look OK.)

  UTL_FILE. Put_line uses as a "new line" everything that uses the o/s database server.

  So if you want to write a file to be used specifically in Windows, you can make your own "new line" rather than using the servers.
  Use PUT rather than PUT_LINE and simply add the two characters that Windows uses to "new line":

  UTL_FILE.PUT(F,
                    I.1||'|'||
                    I.2||'|'||
                    I.3||'|'||
                    I.4||'|'||
                    I.5|| CHR(13) || CHR(10) );
  

• How to write graph of waveform data to text file with the option to the user to do

  So, I'm new to labview and will have bad to write a program in particular.  I have a waveform graph that runs for 120 seconds, generating a sine curve.  I am, however, having a time difficult get the program to write the x and are coordinated in a text file.  I've attached what I have so far.

  The first task I was assigned was to write a program that creates a curve of snusoidal on the front panel by adding a data point every half second for 120 seconds.  The plot should starts only if the user presses a button to start.

  The next part is to give the user an option to write the data generated in a file of worksheet called 'sine.txt '.  The file name and location should be hard-coded.  The file must contain the x and there contact information of each data point in columns separated by tabs, also known as the delimited.

  I spent several hours refining the attached program, and I can't seem to make it work right.  Any suggestions would be helpful at this stage.

  Sincerely,

  A student of chemistry frustrated whose research mentor is out of town

  First, you create files Excel.  You create text files.  And it seems that your writing on a file already created X (time) vs Y (curve of data) that is delimited by tabs.

  All you do is simply too complicated or a Rube Goldberg.

  All you need is the joint.

• Writing a single line of numbers in a text file or write several lines each iteration?

  Hello

  I am currently working on an application that has a few different time-loops at the same time. A single loop acquires data (DAQloop), another shows the data (raw and processed data) on graphs (Graphsloop) and another stores data in an open (Storageloop) ascii text file.

  The data is passed to the DAQloop to the Storageloop through a queue. Now, I leave the Storageloop take the first element of the queue (oldest) to store in the text file each iteration. However, I was wondering if it would be better to let the Storageloop take all items currently available in the queue store at once.

  Does anyone have ideas on this? Who better its? The text file is already open and is simply passed as a refnum.

  THX!

  With normal file primitives LabVIEW, you will get your best speed of disc when you write about 65 000 bytes of disk at once (or read, incidentally).  When I write a similar code, I included a string buffer in the loop of Scripture.  Whenever I get data to write, I add it to the chain.  When the chain hits 65 000 bytes, I write to disk.  You could break this into three loops, as well - a read buffer, and write.  Depending on the current size of piece, you could see a change in the order of magnitude of the speed of disk write.  This write operation is often limited by the conversion from binary to ASCII, not the disk i/o.  If you do this, be careful with your buffer.  You can get some serious slowdowns depending on how you implement it.  This post has some details and examples.

• write the table in its entirety in text file after completing the data collection

  Dell NetBook, Windows XP home, OR-6008, Labview 8.5.1

  I read a psydo real-time app 8 analog signals at 100 Hz.  I can't write directly to a file of data during data collection (processor flash drive to slow down), but can store 4 2D tables separated, with one added timestamp data.  Once I finished collecting data, I would record each table in a separate text (csv) file.  Using takes a loop for in long and using the 'picture to a worksheet string' add labels that I can't change.  I'm climbing down a text file of 3 columns and lines equal the number of samples, I've collected (e.g., a 1 minute session would be 6000 rows and 3 columns).

  1,1.3,1.5,

  2,1.2,1.4,

  3,1.4,1.1,

  4,1.5,1.2,

  5,1.4,1.4,

  etc.

  Thank you

  Troy