WRT-320N

Similar Questions

• MacBook can't connect wireless to wrt-320n

  I just bought a new Linksys WRT-320N (AFAIK version 1, no worm # after model #) router to replace a router wrt54gs has recently been very fluffy, a fall two cable & wireless signals. On our network, I have 2 PCs cable, a cable, IMac, 2 wired game systems and a Macbook. I can connect any wired devices, but cannot get a wireless signal at all! The indicator on the router shows wireless to work, but the macbook can not get a signal (if I connect a network cable, I can however access internet on my macbook. I tried to use mixed, only n and g only, as well as various encryption methods. At one point, I got to a point where I was invited for a wpa key but the macbook repeated connection has expired. I had a signal once using the g-only and no security, but he was very slow only about 8 feet from the router. any suggestions, I'm about to rip off the little hair I have left!

  Try to adjust the parameters of the router wireless... On the configuration page, leave the network as mixed mode... Change the SSID in a unique name, change the width of the channel to 20 MHz only and channel 11 and click on save settings... Under the Advance wireless settings... Change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings... Now, cycle power to the router and check...

• Can not activate my Network Magic software after reinstalling

  After a clean install of Windows 8 Pro I installed my Network Magic Software. After installation, I tried to activate my legal version, but it will not accept a connection to save and activate. I discovered that Cisco supports more Net Magic then activation is not possible in the Netherlands. Cisco said that there is no other tool network of Cisco for my WRT-320N replacement and other Cisco devices. Is it possible to activate my Network Magic software in another way (in the United States or in the registry of Windows or Network Magic)? THX Martin

  One of the reasons why software cannot be installed are because of the firewall on your computer or antivirus software. Try to disable the firewall or disable your anti-virus temporarily and activate Network Magic again.

• Shaw and my new Linksys WRT310N router

  Basically, I tried a router Dlink $ 50 and failed. I tried a $ 100 Linksys router and failed. My ISP is Shaw and no 3rd party router seems to work with it. I have connected my Shaw Surfboard Cable Modem to the Internet port on my router and router connection Port 1 to the Ethernet port on my desktop. I talked to support several times without success. Can someone help me understand this problem?

  "Just to get the mac address of the PC which is on your ISP shaw.

  AFAIK, you don't need to do. I'm on Shaw, using a WRT-320N and have no problem at all (at least not THIS problem).

  There are three different pieces of this puzzle and you have not provided enough information to determine what part is actually the problem:

  -connection makes Shaw so you are also connected to the internet

  -you are connected to the internet but cannot browse, receive emails etc. of your main (or other) machine which is connected BY WIRE to the router

  -you are connected but cannot browse wireless

  If the problem is that the first (and I think that's what you wrote), try the following - it is conceivable that one or more of your IP addresses are contradictory. In order to cross Shaw it is easier if you just "start over." Cut your cable Modem. Turn off your router. Re-turn on your modem and wait until it shows who is connected with the signal. Then turn on your router. This should dispel any questions.

  Most of the machines are set to "dhcp", which will allow the machine to automatically retrieve an address.

  If no joy, please advise what your PC (Windoze? Mac?) and what version of operating system you are using (Windoze Vista? Windows 7? Win XP? OSX? etc.)

• Problem with IBM Thinkpad X 40 (disconnection |) WiFi)

  Hi all

  I use IBM ThinkPad x 40 with XP Pro SP3 x 86. I have the latest drivers for my laptop:

  Wireless driver LAN 2100 3B: driver - 02.08.2006 date; Version - 1.2.5.37
  LAN Driver 1000 MT Mobile connection: driver - 20.08.2008 date; Version - 8.10.3.0
  My router is Linksys WRT 320N, using new firmware: Ver.1.0.05 (Build 2) from 14/12/2011

  Note: The problem (the issue of sectioning) only occurs during downloding, video streaming, only when the connection is fully "charged".

  I use my router with many other features wireless (also ' i' devices) and I do not suffer the same problem.

  I hope that you will be able to help me.

  Kind regards

  saketo

  Hi Alexander,.

  I don't think that it's such a compatibility problem, as far as the card in the x 40 is a speed card B.  By today's standards, it is quite slow.  Don't get me wrong, I love my x40s.  But, one of my friends had a speed card B in it and she would lose the connection on a regular basis.  I put a map of 2200 BG in it and had no more problems with the connection and the download speed has increased significantly.

  Edit: Your 40 x can also draw a 2915ABG wireless card.  Scroll the Maintenance Manual of material for list items and there is one for Europe.

  Here is a link to the Manual of Maintenance of equipment .  Page 81 shows the wireless card.  It is very easy to change, only 2 clips and 2 antennas, and these cards are real cheap these days.

  Or, you can just use a USB wireless adapter to connect with.

  One thing you can try if you are using xp has to go into Device Manager, right click on the wireless adapter and click Properties.  Click the Advanced tab. Make sure the transmission power is set to the highest and feeding management is the highest.

  If you use the Intel Proset software, make sure the Intel throughout the improvement has the highest value.

  Dave

• 320N crashes when you try to transfer data via wifi

  I have the 320N and I am very frusterated.  I would just take it, but I bought it new on Amazon.com, which means I have to pay shipping because I threw away the box and the return shipping of RMA form!  I don't even know if Amazon bring it back without this paperwork, but still the question...

  I have not yet all maps N, but I upgraded to this router because my home internet service is faster than what my old WRT - 54 g could deliver.  This new router performs routing and I can now achieve the nominal speed from my ISP (50 / 10 Mbit/s).

  Can I transfer large files 6 + GB WIRED between one of the LAN ports on this device.  However if I try to transfer more data on wifi, the router simply will stop.  The lights on the front work well, they Flash as there is activity and power light is solid, but it will not pass traffic and SSID wifi disappears.  I run a continuous ping to the router (192.168.1.1, ping - t) and I get<1ms replies.=""  on="" my="" laptop="" i="" initiate="" a="" download="" of="" a="" 1gb="" file="" which="" is="" shared="" in="" my="" windows="" 7="" homegroup.=""  within="" a="" minute="" or="" two="" the="" constant="" ping="" to="" the="" router="" starts="" timing="" out.=""  internet="" access="" to="" anything="" (wired="" or="" wireless)="" instantly="" ceases.=""  new="" introduced="" devices="" will="" not="" grab="" a="" dhcp="" address.=""  existing="" pc's="" whom="" already="" have="" their="" dhcp="" address="" can="" talk="" to="" each="" other="" only="" if="" wired.=""  the="" wireless="" transmitter="" stops="" broadcasting="" the="" network="" and="" devices="" no="" longer="" see="" it="" on="" the="" airwaves.=""  the="" only="" way="" to="" fix="" it="" is="" to="" power="" cycle="">

  It doesn't even have to be a large file via wifi to transfer.  Earlier as I type this post that I noticed the constant ping my other monitor started timing.  I have pedaled power the router in time for me to run for this position.  In fact I had to do it three times in the time it took me to write this post.  It's the most frustrating experience I had with a wifi router/ap, and I play with Cisco equipment at work running IOS real.

  Here's what I've tried so far.

  Reset the default settings by pressing the rear reset for more than 30 seconds button.

  I can confirm this resets the default values as password and all the other settings are default return.

  I tried WPA2 Personal.  I tried WPA.  Router blocks always.

  I tried with all the default settings.  Router blocks always.

  I have reset the router repeatedly.  Always freezes.

  Power cycle it for more than a minute.  Always freezes.

  It with the latest Linksys firmware reflash.  Always freezes.

  What should I do next?  I have a feeling that it is the same problem as in a lot of the advice of HP printer firmware.  This problem is bad solder on BGA CPU connection.  The difficulty that you put the formatter Board in an oven at 400 degrees for 5 to 8 minutes.  After this time let you cool at room temperature.  The oven heats the bad welds enough so that it assigns and gets a better connection.  There are hundreds of messages of success on that.  I also hear that the solder connection problem exists for many of the older game consoles review Xbox 360 causing the infamous "Red Ring of Death".

  So should I try to fight with Amazon for it back and eat the shipping costs?

  Can I cancel my warranty, open the unit and put it in the oven?

  I buy another router from a store, but then put it in the box and take it back?

  I just cut my losses?

  I just use this as a wired router (turn off Wifi) and plug in my WRT - 54 g and the brand that act as an access point?

  Thanks for the tips.

  Well, since it's only a week, Amazon sent me a new.  I just ship this one back in the box they send.  As long as they get it in 30 days I will not be charged.

  This one is def. a dud.  Hope that the next one works much better.  The first thing I do with there is a 1 GB transfer file and see if it freezes.

• On linksys WRT - 1900AC V2 Time machine

  SE your know that Linksys WRT-1900ac can use the time machine function? another post said that can not use time machine to back up! Is it really?

  Thank you!

  Yes, really. the linksys is a wifi router only, and has no hard disk attached. I guess that you can attach a hard drive somewhere (if possible) and put on with the Time machine backup, but this is neither here nor there.  For me, I bought a time capsule airport - very reliable and very easy to install and to use, does the job quietly and well. He also recommended to have a backup of some sort finally... just for security reasons

  JB

• What is the best firmware R7000 that support dd - wrt?

  so I bought this router and have heard it supports the likes of dd - wrt, what is the best firmware for this router and how do I install it?

  According to NETGEAR is concerned, we do not recommend the use of 3rd party firmware as it will void its warranty.

  We always recommend that you update to the latest version of the firmware.

• Deletion of dd - wrt firmware and restore to factory State

  Hi, I have a Nighthawk R8000 I bought with DD - Wrt firmware. I would like to remove this firmware and restore a factory setting. I could have messed up things. I chose the option to restore to the factory, he downloaded some firmware and restarted. Now, I can not access the router at all. It is attached to a Cable Modem provided by my ISP and I found it with an IP address, but when I try to access it without success.

  Any suggestions?

  Thank you my friend, that has worked.

  Herbert

• DD - Wrt Firmware when you set up a ReadyNAS

  Hi, I just got a loan 214 SIN that I will receive in the coming days. My question is will having dad-wrt firmware on my Nighthawk R8000 interfere with the implementation of my ReadyNAS as shown in the Quick Start Guide using the router?
  Thank you

  The process should be pretty much the same. The web interface for DD - WRT is obviously different from ours and DD - WRT has different features.

  If you use RAIDar or ReadyCLOUD to find the NAS, or the NAS I.P. address can be found by looking at the display on the front NAS you should not notice a difference that you should not need to access the router's web administration interface.

  However, if you want to use the web interface of the router to identify the NAS IP address or set a static IP using the router and then...

• Ralink WIreless adapter N TouchSmart 600xt (600-600/t): problem w / 5 GHz 802.11n and DD - WRT fw

  I really didn't have a good experience with HP support trying to figure why my wireless 5 GHz N is not yet detected by my new 600xt.  I tried to load the latest Ralink drivers and it made no difference.  There are a few settings in Device Manager on 5 GHz so I have reason to believe that it does not support 5 GHz as some previous TouchSmart users had trouble with.

  This network is detected by my Dell laptop almost 2 years very well, so I didn't expect this.  My environment really demands N connectivity and even though I have a structured wiring all through my house, it is not likely that the location of this machine will get wired anytime soon.

  I'm using DD - WRT firmware on a WRT600N router.  The DD - WRT software is a 2.4 version, but it's not the newest.  It is:

  DD - WRT v24 - sp2 (07/21/09) std - build 12533

  If someone has already tried a newer version or more old firmware thanks for posting your experiences.

  I had checked that the country in Ralink settings setting should be #7.  Nothing else seems not to apply to this problem.

  I just got my 600xt the other day, but before I bought it I was wondering if 802.11n adapter that support 5 GHz.  It is my understanding that not all do.  I found a card for the 600-1050 version that says this:

  Integrated Bluetooth and WLAN 802.11b/g/n single-band (2.4 Ghz), 2 x 2 featuring MIMO technology

  So I didn't even try helping with my band of 5 GHz on my router.  If yours is as well, so you will not be able to use the 5 GHz.

  Hope that helps.

• Linksys WRT 1900ACS + Linksys SE2800 - gigabit connection problem

  Hi guys,.

  I have a Linksys WRT router 1900ACS that is connected to a Linksys SE2800 switch. The switch is not recognized by the router as a gigabit.

  I also connected a computer with a gigabit network card via a cable, but I get only 100 Mbps speeds. My internet commection is a 500 Mbps. If I connect the computer directly to the router speed is about 470 Mbps.

  Is the switch defective?

  Thank you!

  andvarga wrote:

  For this 10/100Mbps port is displayed.

  OK, then you have a wiring problem. Replace the Ethernet cable with a good cable to know who is connected to before 1000mbps.

• WRT ac1900 connection is wired not reach 300 Mbps

  I have a router AC1900 WRT to gigabit, it should be fast.

  What should I do to get this router to work at the maximum speed available for me?

  If I connect directly to the modem, I get 300 Mbps.

  If I go through the router I get 42 Mbps, the router seems to be limiting it.

  I can't find any option to release this place, ideas?

  Deactivation of MP brought me to 308, I'm okay with that...

  Thanks for the info on the Auto setting of stuff, we would think that they would have standards, don't think not!

  Also, I do not use the Parental control...

  Thanks again, I am fine with 308 Mbps...

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140

• Linksys WRT AC1900 Wifi Shut Downs

  I have a Linksys WRT AC1900 Dual-Band router and it used to work ok but now wifi works after after a restart or deactivate/reactivate but after a random time, it stops working but it is still connected according to my device.  It's really annoying and I am considering buying an access point so that I don't deal with it...  Anyone experience this problem?  Any ideas would be appreciated.  I have about 35-40 devices distributed between 2.4 / 5G with various 802.x standards...

  Because all connections and others are reset to zero with the pads. I presume over time, many features is basiclly fills the buffers and clogging of the device.

  While you wait for an additional AP, I had shuft TURNED off any device of low priority and get the number of connections up to 15 or 20 and test.

  Besure your channels in your area are open and not used by other neighbors that may cause interference.

  Any other WiFi router in the region? Link > use https://itunes.apple.com/us/app/network-analyzer-lite-wifi/id562315041?mt=8 or https://www.acrylicwifi.com/en/wlan-software/wlan-scanner-acrylic-wifi-free/ or to find out. How many?

  Set them manually to 1, 6 or 11 if necessary.