wrt54G and wre54G speed

Similar Questions

• WRT54G and WRE54G does not...

  Hello

  I try to extend my network v1.02.7 WRT54G with an v3.04.01 WRE54G Expander wireless.

  SSID is disabled

  128-bit WEP encryption

  Channel 6 on both devices

  Router IP 192.168.2.2

  Subnet mask 255.255.255.0 router

  Start DHCP 192.168.2.100 IP (max 50)

  Routing Table entry list:

  WAN gateway 192.168.1.1-> 192.168.1.104-> 192.168.2.2 gateway WAN (LAN & Wireless)

  Repeater IP 192.168.2.100 (also tried 192.168.2.3)

  Repeater 255.255.255.0 subnet mask

  Repeater 192.168.2.2 Gateway

  When I turn on both devices and connect with my laptop for the Repeater everthing seems to work very well at first.

  After a few minutes tho the Repeater of fire seems to be "lost in transaltion ' and the connection

  Gets VERY slow (with I mean nothing happens more). It maintains the connection tho.

  When it is connected to the router or via cable and everything works fine.

  Any suggestions before I got this thing in the store?

  Thank you!

  Eureka! I think I got it...

  I did a few tests more with the distance between the router-> expander-> computer.

  If I was in a room with the router, expader and computer everything worked fine.

  It doesn't matter if I was connected to the router or extender or via cable.

  So I thought that the distance between the router and the expander control is REALLY crucial.

  Too close and you're not developing your network enough... too far and you won't get a connection with the Extender that actually works.

  What I did then put the router in the center of the 1st floor and the Expander in the Center

  from the 2nd floor above the router. And now after a few hours everything still works fine!

  Don't be fooled the indicator of the signal strength in Windows!

  All this did not properly although it said very well all the time...

  thx again!

• FireWire 400 and 800 speed question

  I recently bought one of these cords off of eBay for a few dollars.  I have an old external WD which was connected by usb 1.0.  I thought I could get more speed with this cord, but I get all the same read and write speeds of close to 23MBS.

  Any ideas why the speed is slow?  Cord? By car?

  Thank you!

  USB 1.0 MAX is 12 Mbps, which is 1.5 Mbps. (b = bit, B = byte [8-bit]).

  FireWire 400 MAX is 400 Mbps, which is 50 MB/s.

  Without knowing the specifications of the car, I guess that the "old external WD' performance is the limiting factor.

• The satellite C855 - raised average temperature and fan speed

  Hello!

  I got this toshiba Satellite C855 since March this year. It is only recently that the CPU temperature and the speed of the fans have been worrying me.

  When I'm not playing games or doing a livestream my CPU temp is about 35-40% with the regular 50% fanspeed or not on because she was cool.

  When I play games however the fanspeed is up around 66 to 68% with the central unit was 55-60%

  I was wondering if this is normal? or I have to clean it by taking it apart. If it's the second option then I'm worried because I don't want to damage anything inside. In addition, I'm not bad with the inner workings of a computer.

  Any help or information would be greatly appreciated thanks.

  In my opinion there is no reason to panic. T is the logic which is higher under stress, activity of the CPU and CPU produces more heat. Laptop needs to be cooled correctly, so the sensors that control the cooling fans sign up for increasing temperature and cooling fans run on higher speed.

  There is no reason for cleaning. And one day if this must be done please don t do it alone. You are not allowed to do this.

• WRT54G and WRT160NL Torrents

  OK so here is my setup. I have a wrt54g directly on my access to the internet at home. There his hard cable to my wrt160nl where my desktop computer is connected. I would like to open a port for a torrent program to use, but I have no idea how to do that. Ive looked around a few guides but haven't found one that works. any help is really appreciated! (im sure this has been posted b4 but still, I couldn't find any soultions for my situation)

  If you want to run the two WRT as a router and have two separate local networks, you will have a much more complicated installation and the port forwarding for your torrents can turn out to be complicated, if not impossible. You must configure the port forwarding on both routers.

  I highly recommend to use a single router with a LAN configuration. The second router will be used as a switch access point and equipment.

  For example like this:

  1. the WRT54G connect to your modem and a address LAN IP 192.168.1.1.

  2. the WRT160NL is configured with the address LAN IP 192.168.1.2. DHCP server disabled.

  3. the WRT160NL is connected by one of its ports LAN for the WRT54G. Do not use the internet port of the WRT160NL.

  The WRT54G deals now all functions related to the internet. Customers on the WRT160NL connect directly to your local network and through the WRT54G to internet. Port forwarding must be configured on the WRT54G and there only. It's the simplest and probably most reliable installation for you.

  Of course, you can also swap the two routers in the previous configuration, either you use the WRT160NL as internet gateway and the WRT54G only as an access point.

  The access points in both routers must be configured with different SSID as they use differnet wireless standards (unless you spend the WRT160NL wireless-g only).

• How to increase computer speed and bandwidth speed

  For the last 2 weeks I was unable to get into my farmville on facebook.  Talk with the support of zynga and they said after they have reset their side my site works for them.  When I try it gets only so far and the I get a rejection and it resets automatically.  These notes have been left by the developers of farmville, loading time for battery are influenced by its size, the number of elements and the computer speed and bandwidth speed, and even other programs running while you're tying to play.  In the worst case scenario, it can take 5 minutes to load your farm.  Please avoid opening multiple instances of the game.  My computer has been used to the factory settings and all updates were executed.  My computer speed and the speed of bandwidth, I don't know what to do?

  Hi Bobbie,

  Please go to the Microsoft Community Forums.
   
  1. do you get an error message?
  2. What is the brand and model of the computer?
  3. what web browser you use to access the internet?
  4. do you have the internet connection wired or wireless?
   
  I have to improve the speed of the computer, follow the steps given the links:
   
  Ways to improve your computer's performance
  http://Windows.Microsoft.com/en-us/Windows7/ways-to-improve-your-computers-performance
  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
   
  Optimize Windows 7 for better performance
  http://Windows.Microsoft.com/en-in/Windows7/optimize-Windows-7-for-better-performance
  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
   
  I have to improve the speed of bandwidth, see the link:
  Why is my Internet connection so slow?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow
  WARNING: Reset Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.
  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
   
  I hope this helps.

• Playback jerky and double speed?

  First post, sorry if I miss any format directives.

  I was edit a project of files H.264 29.7 fps for a few days, and suddenly today the reading would not output sound is incredibly jerky and seems to be at x 2 speed. This isn't due to the J, K or L keyboard commands, but I have no idea why this is happening, as it happened randomly in the middle of a few basic linear editing. I imported an other H.264 with the same cadence and the quality that the rest of the project and then it began. After removing the H.264 and seeing no improvement, I tried project open an old (and white), who also had identical reading problems. Also, I restarted the computer (possibly including disconnect entirely) and the first resettlement. This glitch is odd, since CC worked without problem for months on this device.

  Any thoughts on why this is happening?

  Details:
  As I reinstalled it first CC, I use the latest version.

  32 GB OF RAM

  Intel core i7

  Graphics EVGA GTX 970

  (Note: monitor the status of the computer while playing, there is no unusual spike in the use of the RAM, there is an increase of about 8% 3% 11% CPU)

  Turn on the screenshot above to "No. Input", fixed the problem of the entry 'default'. All messages "(ne fonctionne ne pas)" disappeared and sound speed / normal has been restored to my projects. " Thanks to all who helped!

• images of 50 fps for export of 25 fps with a normal and slow speed

  Hello world!

  I use first since more than ten years, but now, for the first time that I have to deal with this situation. I have 1080 p at 50 fps 40Mbps images. My output images must be 25 fps 1080 p, but I need to have some video clips to a normal and some speed in slow motion. Any advise how to set my project and sequences? Should I do two sequences - one with 50 fps (for video clips that will be in slow motin) and the other with 25 frames per second and then nest 50 fps sequence in sequence of 25 frames per second for her (50 fps sequence) can be played back in slow motion? Or any other suggestions?

  Thank you!

  I duplicate the image in the project Panel, leave a version at 50 frames per second for use in sections of normal speed and interpret the other at 25 fps for use as slow Mo. use a sequence of 25 p.

• I use LR5.7 based on Windows 7 and got a few pictures 150 000 in a catalugue. Could import, export and rendering speed be increased, if I store the LR catalog on the same drive as my photos? Today the program, the catalog and the photos are all

  I use LR5.7 based on Windows 7 and got a few pictures 150 000 in a catalugue. Could import, export and rendering speed be increased, if I store the LR catalog on the same drive as my photos? Today, the program, the catalog and photos are all on different drives.

  Import and export and rendering speed depends on the CPU. The disk contributes only a negligible amount to import and export and rendering speed. You would spend more time to pass the photos that you would gain in speed.

• Warp stabilize AND slow speed

  I want to warp stabilize AND slow speed which are incompatible, so what is the recommended route on this please?

  FOR EXAMPLE, I believe that we must export an and re-import to another, or what? In what order?  Is there a smarter way?

  Export of reimportation down Imaging?  These sorts of things.

  Thank you

  Steve Z

  Stabilize first.

  Choose an export format uncompressed to the DI.

• Questions and data speed WRT54G

  Installation: Only WinXP Pro, Comcast cable modem RCA DCM425, router WRT54G Rev8, cables Ethernet, Firefox with Zone Alarm off.

  Following the statement of the toomuchdonuts, I tested my WRT54G Rev8 to speedtest.net. I tested four times each to three different servers:

  A. within 500 miles of me

  B. to halfway across the country from me

  C. background from me.

  Here are the results, based on an average of three results for each server, with and without the router.

  A. without router: download speed 19.5 Mbps, upload 2.3 Mbps, ping 25ms
  A. with router: download speed 27.0 Mbps, 2.5 Mbps, ping 25ms speed

  B. without router: download speed 19.2 Mbit/s, upload 2.7 Mbps, ping 70ms
  B. with router: download speed 21.0 Mbps, upload 2.7 Mbps, ping 70ms

  C. without router: download speed 17.0 Mbps, upload 2.7 Mbps, ping 98ms
  C. with router: download speed 19.5 Mbps, upload 2.7 Mbps, ping 100ms

  These are very surprising numbers. Issues related to the:

  -How can they exceed speed 12 Mbit/s for my service Comcast quotes?

  -What is average ISP of the graph? The bar seems to be about 15 Mbit/s.

  -How can be higher than those without the router with the router speed?

  Very confusing.

  (1) cable Internet service is a shared service.  You and many of your neighbors share a limited amount of bandwidth.  The city of 12 Mbps is what Comcast expects to be able to provide most of the time.  If your neighbors are offline, or limited use of their connection, then you can get more speed from your city.  In addition, be aware that the connection speed is a little art.  Different sites will sometimes quote significantly different speeds, more difference can be explained by distance alone.  The main advantage of documenting your speed is (1) to ensure that you get what you pay for and (2) have a basic registration, in which case your line never speed is significantly reduced.

  (2) I guess the 'average of ISP"is the average speed that other Comcast subscribers get.  This info is very useful because it does not seem to distinguish the 12 Mbps subscribers subscribers Comcast 6 Mbps.

  (3) normally, with and without the router speed is about the same.  Because the router goes faster, I guess that maybe the router generates more favorable package, or the moment of package size.

  (4) generally, the site that you sign in, your Internet connection slowing will go furthest.  This is because remote connections usually have to go through several relay points, slowing down the connection.  Your measurements show this well.

• Fake screenshots on links youtube video and the speed of the links dials.

  Firefox displays wrong pictures on video links and also wrong dials for the speed dial add-on. Problem goes away after focusing on the problem of link.
  If restore system - everything very well. If then updated firefox and (or) flash - problem reappears.

  Thank you!

  Start Firefox in Safe Mode {web link}
  While you are in safe mode;

  Type of topic: preferences #advanced< enter > in the address bar.

  Under Advanced, select General.
  Find and stop using hardware acceleration.

  Search web sites secure. Are there problems?

• Satellite A660 - 11 M and fan speed controller

  Hello

  Is there anyway to reduce the speed of the fan on the A66011m Satellite?
  The fan operates at 67% and makes too much noise for use in an office environment. Is it possible to reduce this?

  Thank you

  Adam

  Hello Adam

  There is a single way to do this. Go to power management and open the advanced power settings for the management of the power supply you use.
  You will find Toshiba Power Saver options and parameters for the method of cooling. Open it and put them in optimized battery.

  This should reduce the activity of fan cooling.

• Satellite C660-1F1 - Question about newer drivers and the speed of the memory

  Some of the drivers for this laptop are outdated compared to the most recent drivers on peripheral manufacters website. Is it safe to use these new drivers or is it recommended to stick with the old drivers that are on the Toshiba site?

  And second question: is it possible to make the fastest possible working memory supported? Don t BIOS options include options for the parameters of memory. Why the memory is running as low mhz in case of default? CPU - Z shows that the current frequency of dram is 532, 2 mhz. What is the maximum, it is at 667 mhz? Probably she can´t be 1 066 MHz as promised in the specs?

  Hi cryogenized,.

  > Some of the drivers for this laptop are outdated compared to the most recent drivers on peripheral manufacters website. Is it safe to use these new drivers or is it recommended to stick with the old drivers that are on the Toshiba site?
  Why you want to update your drivers? Do you expect a gain of performance with newer drivers?

  Way General, with official Toshiba drivers you are on the safe side because they are pre-tested. If you can make sure that they work properly and don t cause property damage. Install the other drivers happens on your own risk!

  > And second question: is it possible to make the fastest possible working memory supported? Don t BIOS options include options for the parameters of memory. Why the memory is running as low mhz in case of default? CPU - Z shows that the current frequency of dram is 532, 2 mhz. What is the maximum, it is at 667 mhz? Probably she can´t be 1 066 MHz as promised in the specs?
  The laptop is equipped with modules of DDR3 1066 MHz and the RAM speed is dependent on the FSB of the processor. If your CPU is throttling down, RAM modules will work also on low speed. On a high utilization of the processor (100%) the RAM modules must run with speed of 1066 MHz I think.

• Monitor activity and Mac speed

  My desktop computer iMac (early 2009 with OS X El Capitan; version 10.11.3; Clocked at 2.66 GHz Intel Core 2 Duo processor; Memory 2 GB) is running extremely slow. That's what I've done so far: I managed the startup items by removing unnecessary applications. I was told do NOT install software of cleaning as MacKeeper or CleanMyMac.

  Then, I had planned to quit some applications that are taking place on my Mac RAM. I understand that, to stop the app (s), I click on the app (s) in the list displayed in the activity monitor. My question is, how do I know which applications to remove? Some have names that I don't recognize and some list the system as the user and one administrator list any 'root' for the user.

  Should I forget speed up the Mac and plan to buy a new computer?

  readersinc wrote:

  Should I forget speed up the Mac and plan to buy a new computer?

  It really depends on if you like throwing money at problems or if you want to try to improve what you already have. A newer Mac is usually faster, but you won't have it.

  2 GB of RAM is a bare minimum to 10.11 as State of Apple in the requirements...

  Update of OS X El Capitan - Apple Support

  Any computer running on the bare minimum will have problems to do several things - you should simply stop all applications running in the Dock.

  Activity monitor is not intended to be used as you describe - if you force quit the wrong process or app, the computer may hang, become unstable, or losing your data. Please stop looking at that and try to kill the process, it is intended to help you to diagnose the current state, force quit is not designed for this.

  You can buy more RAM for your Mac, allowing him to perform tasks more, otherwise you'll have to accept that it is better to do one or two tasks & quit other open applications.

  An Apple store may help you if you need advice on the installation of RAM, I think that this model can support up to 32 GB (Apple 16 GB of State, but the newer RAM modules are larger & seem to work) but you should check the model identifier in system information. That appears under the Apple menu, hold the option key & open the Apple (a.k.a alt key).

  RAM is normally easy to ride, but you can get a technical person to do it for you. There are user guides made by Apple for the RAM Assembly in each model.

  Slow can also be caused by other software or slow hard disks. You want to create a report to show what is installed? Etrecheck is designed to do this...

  http://etrecheck.com/

  P.S. Apps like Clean My Mac & Mac Keeper will use more RAM, so that they won't really help your situation. Most of their tasks seems useless to me.