WRT54G AP when connected to an another WRT54G

Similar Questions

• Get a "Cannot find driver" error when connecting to my HP Laserjet 4350 PCL5 for workgroup computer.

  * Original title: problem with HP Laserjet 4350 PCL5

  I have a shared network printer. But when connect us to another computer in the workgroup. It says that it cannot find the driver. Computer has Windows 7 64 bit. I tried my drivers and .inf files, but nothing works.

  Hello

  This problem may occur if the printer drivers are not installed properly.

  I suggest you run the HP print and Scan from following link doctor and see if that fixes the problem.

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&docName=c02073861&JumpID=ex_r4155/HHO/IPG/ccdoc/trailhead_doc

  You can try to install the last printing software, drivers from the following link and check if it helps.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=412171&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswEnvOID%253D4063%257CswLang%253D%257Caction%253DlistDriver&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  For more information, see the links.

  Problem for HP LaserJet 4350 printers

  Share a printer

  Install a printer on a home network

  Keep us informed on the status of the issue.

• WRT54GC failed to get a valid gateway entry when connecting through PPPoE

  Hi Experts,

  I'm moving my WRT54G Router that uses more than 5 years for a WRT54GC I got from my friend. I have clone each entry of the WRT54G to the new MAC address of one, even. Here's what I captured of the old WRT54G Router when it connected via PPPoE

  Connection type: PPPoE
  Connection status: connected
  IP address: 114.91.200.128
  Subnet mask: 255.255.255.255
  Default gateway: 124.74.12.242
  DNS 1: 180.168.255.118
  DNS 2: 116.228.111.18
  DNS 3:
  MTU: 1492

  from the web administration interface, I can ping and traceroute yahoo.com, so can I browse any website from my PC.

  and here is what I have captured new WRT54GC router when connected via PPPoE

  Connection type: PPPoE
  IP address: 180.158.83.182
  Subnet mask: 255.255.0.0
  Default gateway:
  DNS1: 180.168.255.118
  DNS2: 116.228.111.18

  the web administration interface, I can ping and traceroute yahoo.com, but I can not browse any website from my PC.

  Could you get it someone please let me know if there is something I misconfigured?

  Thank you

  Probably your ISP don't like it if you try to connect two times with the same account of different devices.

  I suggest you press the disconnect on the WRT54G to close the PPPoE session before trying it on the new.

  Or stopping for the night and try the new router first thing in the morning...

• When connecting on MacMini, password is auto-complete with a myriad of points and is not the right password

  When connecting on MacMini after I click on the user, the password field is auto-complete with a myriad of points and is not the right password.

  There suddenly / maybe after the most recent update 2015-008, which I installed it on 8 January 2016.

  I need to delete points, usually I can remove them by double clicking on it and pressing the delete key, but they will not simply remove by clicking in the field and using the delete key, as would be normal. Sometimes it takes a few tries to remove the points, and then I can connect.

  Does my keyboard or a virus, my usb port, the update of security or something else...?

  I use this computer without problem for a few years.

  Thank you, Kathy

  osX version 10.9.5 processor 2.3 GHz intel core 17

  First try another KB

  Next

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• No signal HDMI when connected to the TV (Aspire V3 - 571)

  Hello

  I'm really trampled here and need help. I have an Aspire V3-571. Please see the summary below in the chips:

  1 used to operate correctly when it is connected to my TV (via a HDMI cable)

  2. one night, what laptop was connected to the TV, picture started to blink

  3. after 20 minutes, the HDMI signal is not detected for the laptop

  4. Update driver Intel HD Graphics 3000 (Date: 29/01/2014 Version: 9.17.10.3347)

  5 tried to use different HDMI cables

  6. press Fn + F5 does nothing

  My TV HDMI port works with other devices when connected to it. What I'm missing here? Is there a defect of material with my laptop?

  Any advice or help on this would be much appreciated. Thank you.

  Hello...

  All information provided I see that you have already updated driver, tried different cables and also checked the HDMI port on your TV. I suggest you check the laptop's hdmi port by plugging another device like external monitor.

  If you don't get any screen, it could be a problem with the laptop's hdmi port.

• Help! My Sansa Clip + is no longer recognized by my PC when connected by USB port!

  Reading, the latter time, ' said, 'written' only when connected. Normally, he alternates between the 'Reading' and 'Writing' when it is connected to the PC and, therefore, it USED TO BE recognized by the PC in these conditions. The device is not recognized in Windows Explorer as a device or disk as usual. I use Windows 7. The device is not recognized by Windows Media Player synchronization purposes: I can't synchronize playlists of music more.

  You try to reset by pressing the power button / stop 20 seconds does not help.

  Using different USB ports does NOT help.

  The cable using different USB does not help.

  Another computer has NOT appeared.
  

  SOLVED BY TECH SUPPORT CHAT: Here is the conversation with the restorative troubleshooting following steps:

  Jonathan Bailey is me:

  Kyle Ahmed is the man of SanDisk tech support:
  

  
  

  Of the troubleshooting information for "not recognized by PC.
  ***************************************************************************

  Kyle Ahmed: Please tell me the exact model, color, and the ability of your Sansa player?
  Jonathan Bailey: black, Sansa Clip +.
  Kyle Ahmed: Please provide me with the ability as well?
  Jonathan Bailey: I think it's a 4 GB
  Kyle Ahmed: Please tell me when and where did you buy this drive?
  Jonathan Bailey: Citrus Heights, CA, Jan 2012 target
  Kyle Ahmed: If I understood you correctly, your drive is not getting recognized by the computer?
  Jonathan Bailey: No, it is not when connected by USB.
  Kyle Ahmed: Please tell me, are you using Windows 7?
  Jonathan Bailey: Windows 7
  Kyle Ahmed: I understand. Please connect the player to the computer.
  Jonathan Bailey: It should say READING and WRITING.
  Kyle Ahmed: very well. If you please, right click on computer and select manage.
  Kyle Ahmed: Click Device Manager in the left pane.
  Kyle Ahmed: Sansa player will be displayed in the right-hand of Device Manager: 1. USB mass storage device
  (if the player has MSC) 2. portable (if the player is set to MTP mode)
  Jonathan Bailey: he is profiled as a Portable device Sansa Clip + 4 GB
  Jonathan Bailey: a yellow exclamation point icon
  Kyle Ahmed: right click on the drive with the error indicator and choose uninstall.
  Jonathan Bailey: icon done, went
  Kyle Ahmed: In the top menu, click Action, and then select search the hardware changes.
  Jonathan Bailey: said device still WRITTEN in reading
  Jonathan Bailey: said ball driver software not properly installed
  Kyle Ahmed: very well. Please disconnect the player from the computer.
  Jonathan Bailey: ok, says still WROTE
  Kyle Ahmed: Please press on and press and hold power for 20 seconds to turn it off.
  Kyle Ahmed: Then, press and hold the Center button while connecting the device to the computer.
  Kyle Ahmed: It is on the first view the drive between the up/down/left/right button.
  Kyle Ahmed: This allows the computer to recognize the drive as a removable storage as well
  You should see it in the devices with removable storage section in the computer.
  Jonathan Bailey: it says CONNECTED then he says SAN Disk alternately
  Kyle Ahmed: Check if the drive is recognized by the computer.
  Jonathan Bailey: there is now a SANSA CLIPP (F): in my Windows Explorer navigation pane
  Kyle Ahmed: It seems that pilots of the PSG of your computer went corrupt due to which your
  Player is recognized not earlier. In this case, what you have to do is to reinstall Windows Media Player or
  change the USB mode of the player to MSC permanently solve the problem. But the MSC mode will not allow you
  by creating playlists with Windows Media player to transfer songs from your player.
  Jonathan Bailey: Windows Media Player Sync now recognizes "SANSA CLIPP"
  Jonathan Bailey: I need Windows Media Player synchronization capability or the Sansa is not good for me.
  Kyle Ahmed: Jonathan, please check if the player is displayed under the Portable devices or with
  Removable storage in the computer (Explorer)?
  Jonathan Bailey: It's showing under devices with removable storage in the computer (explore).
  Kyle Ahmed: Please disconnect the player from the computer.
  KKyle Ahmed: Please activate the drive.
  Kyle Ahmed: Then go to settings > system settings > USB mode.
  Kyle Ahmed: Then in the player's main menu, go to settings > system settings > USB mode.
  Kyle Ahmed: PSG and click the Center button to confirm.
  Kyle Ahmed: very well. Now, connect the drive to the computer and check if she gets recognized or not.
  Jonathan Bailey: OK now recognized as his former self again.
  Kyle Ahmed: If the player is now recognized and alos appear in Windows Media player, I'm wrong?
  Jonathan Bailey: I have not checked the media player yet
  Jonathan Bailey: it is recognized in Explorer
  Kyle Ahmed: Please disconnect the player from the computer.
  Kyle Ahmed: To check the version of the Firmware of the player.
  Jonathan Bailey: ok, it says REFRESHING YOUR MEDIA
  Kyle Ahmed: very well. I would like to know once you are in the main menu of the player.
  Kyle Ahmed: Go to settings > system settings > Info.
  Kyle Ahmed: Give Me the version of the firmware of the drive please.
  Jonathan Bailey: Version V01.02.16A, isn't it?
  Kyle Ahmed: It seems that the version is up-to-date.
  Kyle Ahmed: The reason why it took more time to update the media earlier must be because of the large amount
  songs that have been transferred, which can take the time to read.
  Jonathan Bailey: OK, for 2 500 songs, it usually takes about 15-20 minutes
  Kyle Ahmed: I understand.
  Kyle Ahmed: You have faced a temporary problem that was solved by resetting the player and refreshing the drivers of your computer.
  Kyle Ahmed: You should not face additional problems.

• screen flickers when connected to the internet

  my screen flickers when connected to yahoo on the internet.  doesn't seem to be as bad when visiting other sites such as Google.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > looking for the latest graphics drivers for Vista > download/install them

  See if the information below helps you solve the problem/s you have with Internet Explorer:

  http://support.Microsoft.com/default.aspx/KB/936213/?p=1

  "How to optimize Internet Explorer"

  Configuration in Windows Internet Explorer 7 and Windows Internet Explorer 8 settings can cause one or more of the following problems:

  ·     You experience performance issues in Internet Explorer.

  ·     You receive an error message in Internet Explorer. For example, you receive a message error "Internet Explorer cannot display the webpage".

  ·     Internet Explorer stops responding.

  This article describes how optimize or reset Internet Explorer in Windows Vista to solve these problems.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/936215

  "How to solve the problems of Internet Explorer in Windows Vista and Windows XP"

  This article explains how to solve any problems that you may experience when you use Windows Internet Explorer 7 or Windows Internet Explorer 8 on a computer that is running Windows Vista.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/936214/

  "How to solve compatibility problems that affect Internet Explorer 7 in Windows Vista"

  This article describes how to troubleshoot software compatibility affecting Windows Internet Explorer 7. To help determine which program may be the cause of the problem, you can do the following:

  1 use the mode safe mode with networking

  2. perform a clean boot

  3. use another user account

  4 scan your computer against viruses and spyware

  5. run Internet Explorer 7 in "no Add-ons" mode

  Hope the above helps.

  See you soon

  Mick Murphy - Microsoft partner

• After running System Restore my computer asks for a password when connecting and I don't remember the password.

  I am running Vista Home Premium on a laptop Toshiba Satellite L305.  I ran the system restore due to a problem of "Internet Explorer cannot display the website" (by Microsoft troubleshooting guide for this problem) and selected restore point earlier.  Now the computer asks for a password that I don't remember.  I tried all the possible passwords I can think.   There is only a single user account on this computer.  The administrator account should be disabled, it is not an option when connecting safe mode.  I don't have a system repair disc set.   Is it possible to run the system back restore to select a more recent restore point which does not require a password?  Or y at - it another way to connect to the computer?

  http://Windows.Microsoft.com/en-us/Windows-Vista/undo-system-restore

  If you tried to use the system restore to solve a problem, but the problem remained or other problems were introduced, you can undo the restore operation. After you cancel the system restore, you can try using a different restore point.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/189126

  "Microsoft's strategy concerning lost or forgotten passwords"

  Microsoft cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Mick Murphy - Microsoft partner

• No sound when connecting my new XPS 9530 to my TV with a HDMI cable

  I got my new laptop XPS 9530 for 3 weeks now and can't get any sound when connecting it to my TV with an HDMI cable.  I struggled to find a solution that works so far.  I tried so many solutions for example suggested, I went to SOUND / playback devices and the only option is to Audio speakers (Realtek High Definition) but not option for HDMI. I have re-installed video and audio drivers but still no success.

  The worst is that I sent to Dell Support FOUR times without reply after that initial automated response.

  Hello, I had the same problem on my XPS 9530 but it corectly established after a few moments, fundamentally sound has been activated later than the video.
  In any case, you can still use Windows troubleshooting utility, or what I would sugest is to test it on another TV and give him a few minutes and then also try another HDMI cable, your current version is perhaps too old or something.
  BTW do you have updated the video drivers intel and nvidia? If not, please do so.

  One last thing, if you get no response from email support you can always make a phone call if your problem is urgent.  ;)

• session remote desktop connection logon message: another user is currently connected to this computer

  I'm trying to figure out how to make a remote desktop connection without the user on the computer, as I log to get to kickoff. When I start the DRC while the other computer is in use, I get a message saying... session remote desktop connection logon message another user is currently connected to this computer. If you continue, this user should disconnect from this computer. Do you want to continue?

  Click Start / Help, then search for help on the "fast user switching".

• BlackBerry smartphones < my blackberry lost day and time when connect you the bb to computer!

  Hi, my lost bb day and time when connect bb to the computer, the change time bb and another area, it is normal?

  My phone says dealer "it's normal in this smart phone" is really true?

• The blue windows screen Driver_irql_not_less_or_equal 7 when connecting the LAN cable?

  Hi all,
  I just want to ask how to solve Driver_irql_not_less_or_equal windows 7 blue screen when connecting the LAN cable?
  pls help me...
  Thanks in advance...

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are that if you are unsure if you are, you are not)

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.
  * Zip up the copy.
  * Join ZIP archive to your message by using the button (attachments) "trombone".
  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.
  * On the Advanced tab, click Startup and recovery... Settings button.
  * Make sure that automatically restart is unchecked.
  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).
  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.
  * OK your way out.
  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32
  Go to 'file', 'save' and download the PDF is saved with the DMP
  (Instructions for XP, Vista, Win 7, Win 8)

• connection mysql and oracle ORA-28545: error diagnosed by Net8 when connecting to an agent

  Hi all

  I have Oracle 10.2.0.5 server and MySQL 5.3 on windows environment. all are 64-bit.

  I want to connect to MySQL. I do the following

  Configure Listner.ora

  SID_LIST_LISTENER =

  (SID_LIST =

  (SID_DESC =

  (SID_NAME = PLSExtProc)

  (ORACLE_HOME = C:\oracle\product\10.2.0\db_2)

  (= Extproc PROGRAM)

  )

  (SID_DESC =

  (GLOBAL_DBNAME = ORCL)

  (ORACLE_HOME = C:\oracle\product\10.2.0\db_2)

  (SID_NAME = ORCL)

  )

  (SID_DESC =

  (SID_NAME = mysql)

  (ORACLE_HOME = C:\oracle\product\10.2.0\db_2)

  (PROGRAM = HSODBC)

  (ENVS = LD_LIBRARY_PATH = C:\oracle\product\10.2.0\db_2\LIB)

  )

  )

  LISTENER =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP)(HOST = oradev.hct.org) (PORT = 1521))

  )

  Tnsnames.ora configuration

  ORCL =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = TCP)(HOST = oradev.hct.org) (PORT = 1521))
  (CONNECT_DATA =
  (SERVER = DEDICATED)
  (SERVICE_NAME = orcl)
  )
  )

  EXTPROC_CONNECTION_DATA =
  (DESCRIPTION =
  (ADDRESS_LIST =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC0))
  )
  (CONNECT_DATA =
  (SID = PLSExtProc)
  (PRESENTATION = RO)
  )
  )
  MySQL =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = TCP)(HOST= 10.153.103.5) (PORT = 1521))
  (CONNECT_DATA =
  (SID = mysql)
  )
  (HS = OK)
  )

  create file initodbc.ora in the folder hs

  HS_FDS_CONNECT_INFO = mysql

  HS_FDS_TRACE_LEVEL = OFF

  Restart the listner

  tnsping

  C:\users\administrator > tnsping mysql

  AMT Ping Utility for 64-bit Windows: Version 10.2.0.5.0 - Production 08-NOV-2
  015 13:02:52

  Copyright (c) 1997, 2010, Oracle.  All rights reserved.

  Use settings files:
  C:\oracle\product\10.2.0\db_2\network\admin\sqlnet.ora

  
  TNSNAMES adapter used to resolve the alias
  Try to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP) (HOST = 10.153.103.5)
  (PORT = 1521)) (CONNECT_DATA = (SID = mysql)) (HS=OK))
  OK (0 msec)

  Create the connection odbc for Unicode

  

  the test is successful

  now, I create the dblink

  create public mysql database link to connect to cssDBTeam identified by oracle using "mysql";
  
  

  then try to select from a table inside the MySQL database

  SQL > select * from appeal@mysql;

  Select * from appeal@mysql

  *

  ERROR on line 1:

  ORA-28545: error diagnosed by Net8 when connecting to an agent

  Cannot retrieve the text of the message NETWORK/NCR 65535

  ORA-02063: preceding 2 lines of MYSQL

  How could I solve this problem?

  Thank you.

  Hello

  I realize that your problem is that 10.2 HSODBC was never focused on the Windows 64-bit platform and was only available on 32-bit Windows.  You can not install the 32-bit on WIndows 64-bit HSODBC.

  Your only option is to install 11.2 DG4ODBC on your platform Windows 64 - bit, or if you have a RDBMS 10.2 installed on another platform, then you could use HSODBC as part of this installation and connect from the RDBMS on Windows 64 - bit using the links in the database.  HSODBC 10.2 software could not be installed as a stand-alone product and was only available as part of an RDBMS install.

  Kind regards

  Mike

• View Client remembers the last connection protocol (even another computer)

  Currently, the customer discovers learns this last protocol used when connecting to a desktop computer from the view connection server.  It is a big problem.

  EXAMPLE - I have a user who has a PC at work and a PC at home.  I put the default protocol of pool to PCoIP.  They connect at work (pcoip).  They go home and have move to RDP.  They return to work and have move to PCoIP.  They go home and have to swith RDP...

  Why would you transfer an environment setting like that from one computer to another with no ability to override?  This will cause the use moving between computer and protocols to constantly change their protocol settings.  If the client view would ignore the configuration of the server protocol, then they could leave PCoIP together at work and RDP set at home and be able to quickly connect.

  This post explains where the settings is saved on the login server (POST).

  Is it possible with view 4.5 to replace it?

  VMWARE please correct this by adding a parameter to the client view each Protocol user setting from the server connection or ignore it and use the last protocol used by the client to view software.

  I agree it is a bit strange, but you can set a parameter at the launch of the View client to specify whether to use PCoIP or RDP.

  desktopProtocol - XXX will attempt to use the specified protocol desktop display.

  ____________

  blog.eeg3.net | Useful links related to VMware

  If you have found this device or any other post useful, please consider the use of buttons useful/correct for award points.

• Still play songs from my iPhone when connected to wifi

  Had this problem before, but it stopped happening a while ago only to re - emerge with the iOS 10 update.

  I'm running on an iPhone 6 and used to play my music library on shuffle.

  Over the years, I've deleted some songs from my library of songs, but they remain available for re - download in iCloud.

  However, from time to time, if I play songs on shuffle when connected to wifi, one of these songs removed will be available on my phone and play.  It does not download to my phone and still only available for download on iCloud.

  Is it possible to stop these removed songs to play on quite my phone when connected to wifi?

  I'll add that I'm not on all subscriptions either except to increase my storage iCloud.

  Post edited by: sound_man

  I believe that you open the music application, select "download music", then make your choices from there.  If you do not select the "download music" it will first play all the songs that you have purchased.