WRT54G V3.0 Web Interface broken after FW update

Similar Questions

• WRT160nV2 Web Interface broken after FW update

  Hi all

  After upgrading the firmware on my router, the Web Interface is more usable. Missing buttons, etc. Even if I go directly to the 192.1681.1.1/update.asp also this page is useless and so I can't do a FW update again. The router works as all parameters was intact. But I can't make any changes to the router. How can Flash the router again? TFTP, etc.

  Best regards

  Albert

  Well, that was the problem after the firmware upgrade, you should try to downgrade the firmware of your router... Firmware build 011 v2.0.02 has some issues, so maybe after a downgrade of firmware you'll be able to see the full web interface...

  For the Downgrade of Firmware see this

  Don't forget to reset the router to factory settings after the downgrade of firmware... If the web interface is always so high an IE, click on tools > Internet Options, and then delete all files, cookies, history, forms... GoTo 'Connections', make sure that never Dial a connection is selected, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  If the above fails, then try another browser or another computer...

  If all above fails them, then I would say there is something wrong with the router and you should get it replaced...

• WRT54G v4 unusable web interface after firmware update

  I tried to upgrade (actually downgrade) my WRT54G v4 firmware 4.30.11 to 4.21.1. When the progress bar reaches the mark to halfway, I got the message saying that the upgrade was successful. However, now the web interface is so messed up that it is unusable. It's a sign that something went wrong.

  Power, WLAN, Ethernet 1, and Internet lights are all green solid, which should be a good sign. After the upgrade, the web interface says "WRT54G 4.21.1', which is the firmware messed up I am downloading. Browsers, then restart my computer, I have confirmed that it is a router problem, not a problem of the browser cache. I also tried to do a hard reset by pressing the reset for 30 seconds button, unplug the router while holding down the button of reset for 30 seconds and then plug the router while holding down the button of reset for another 30 seconds. This has not fixed anything.

  I encountered a similar problem after an update of the firmware several years ago and the fix to upgrade the firmware using TFTP. This time, however, the TFTP utility could not download the firmware. Using a hack that I found on the internet, I have re - download the 4.21.1 firmware, but the web interface was always messed up. I then downloaded the 4.30.13 firmware. The web interface is still messed up, but then he said "WRT54GL 4.30.13. I then went to the firmware I wanted, WRT54G 4.21.1. The web interface is still screwed up, but said «WRT54G 4.21.1»

  Anyone know how to solve the problem? Yet once, it took place immediately after a firmware update, the web interface is unusable, is not a problem of the browser cache and tried a hard reset.

  Thanks in advance if anyone can help.

  My router model is WRT54G v4. The v4 WRT54G and the WRT54GL are generally considered to be the same device with different model numbers. According to the article of Wikipedia WRT54G, "the WRT54GL is technically a reissue of the version 4 WRT54G."

  I used the firmware 4.30.X for years without problems. However, I decided to switch to the 'right' firmware for my router and something went wrong during the upgrade.

  I solved the problem. I basically just dropped the Linksys firmware and uploaded the DD open source-WRT firmware mini instead. Now everything works fine.

• Managing policies broken after the Update Rollup 4

  Server details
  Server product	ColdFusion
  Version	9,0,1,274733
  Edition	Standard
  Operating system	Windows Server 2008
  OS version	6.0
  Update level	/C:/ColdFusion9/lib/updates/chf9010004.jar
  Version of the Adobe driver	4.0 (build 0005)

  I recently upgraded to 2 of my servers to the Rollup 4 in response to bullitin of security APSB13-03. Everything seems to work ok and the update went through fine. Happened me on the accident click the font management link and was surprised to see that what was once a completely filled page now simply read the fonts not found. After looking through the many posts on the forum and google searches, the similar mention only I'd come through was http://forums.adobe.com/message/4495733#4495733. However, unlike the OP in this post, I was able to add new user-defined fonts. The only thing that I havn't done is go back the update since that let me a big problem in the form of a security hole. My problem is that no system font doesn't seem to appear on the page, but I think that the fonts are really at work even if they do not show on the page. I ran across the post of carehart http://www.carehart.org/blog/client/index.cfm/2011/10/21/why_chfs_may_break and determined that everything was done correctly, however if wrong something I can't say what.

  Everyone knows this? I know that this Cumulative 4 update was just released yesteraday, but maybe even a similar expiernce with another fix?

  Vishal

  Vishal,

  Please follow the step #12 to http://helpx.adobe.com/coldfusion/kb/cumulative-hotfix-4-coldfusion-901.html to copy the file jpedal.jar into the directory lib to see restart the CF service and check the section of police management in the CF admin to see if the problem is resolved.

• HA broken after I updated my file/etc/hosts

  Hi all

  I have a urgentquestion to ask.

  I've updated my host from my ex file two servers and he beat HA.

  He said this formula the VC client: cmb delete failed

  I tried to uncheck HA and double-checking HA but I didn't work.

  From what I see in previous posts, it could be a DNS problem.

  I can ping my shortname, FULL domain name and ip are both servers without any problems.

  Anyone has nay clue as to what I can do to fix this freaking?

  Thank you.

  Are u restatrd sevice

  1. service mgmt-vmware restart

  1. Service vmware-vpxa restart and try

• WRT54G2 v1 broken web interface

  Sorry my bad English.

  My problem:

  in the web interface broken router (some items hide / present or not): see puctures

  
  
  
  

  in pic2 you see - upgrade button to hide... I can't upgrade or rewrite the firmware.

  I am trying:

  try to rewrite the firmware of the web interface
  Try reset firmware by pressing the reset button on the back...

  try to change the browser (firefox ie opera safari)

  try disabling (css, scripts, views) in browsers

  try to change the Connection port on the router and the pc

  Try change mobile pc station - another laptop

  try to connect other OS (ubuntu xp vista win7)

  .. .no result

  What can I do to restore the original firmware?

  solution found:

  Turn the router off

  then press reset button and return power

  Press the reset button for the router to start up... and then open the browser

  router must be in management mode.

  then wrote dd - wrt VxWorksKiller-G2V1 - new.bin (original firmware does not work I try!... but maybe you happier)

  After this router reboot (power cable reconnect)

  and wrote the firmware dd - wrt.v24_micro_generic.bin main by tftp

  cd /d tftp.exe -i 192.168.1.1 PUT dd-wrt.v24_micro_generic.bin
  

  After that reboot the Router 2 times - (reconnecting the power cable)

  and do 1 hard reset (30-30-30 method)

  It has helped me.

  dd - wrt site

• ACS Web Interface 5.1 does not

  We have a Cisco Access Control Server (TACACS+ version 5.1) with an additional
  
      2 port NIC card. This produces 4 ports on the ACS server(G0 through G3).
  
  After initial setup of the ACS server with an IP address on G0, I connected a Windows 7
  
      server with IE8 to G0. The ACS web interface appears (after accepting certificate) and I
  
      entered some user accounts and NDGs.
  I then connected the ACS server to a configured port with port-security on our 6500
  
      switch. The port becomes err-disabled since the MAC address does not match up. It appears
  
      that the onboard NIC on the ACS server is bonded thus producing the MAC address issue.
  To fix this connection issue, on the ACS server, I cleared out G0 and setup G2 (additiional
  
      NIC card) with the IP address. After connecting to the 6500 switch, the ACS server port
  
      works fine.
  I removed the connection to the 6500 and connected the Windows server to the ACS.I can ping
  
      the ACS server but the web interface is now unavailable unlike before. I do not get a
  
      certificate warning on IE, it just states that internet not available.
  On ACS, the 'show' status of acs shows all the processes are running and initialized.
  Any help would be appreciated. It has got me stumped as all I did was change NIC configuration
  
      on the ACS server.
  Antonio
  
      

  I wanted to check if the failed to load web interface could also be due to something on the 6500 switch.

  So far:

  You have been able to see the Web interface with the ACS configured on G0 and directly connected to the PC Win 7.

  With the G0 set to ACS, you saw some MAC problem and so no web interface.

  With the ACS configured on G2, you can test the ACS server when it is directly connected and connected to the 6500, but in both cases do not display the web interface.

  So, it seems that you have two options:

  (1) seek to solve your problem of port security 6500.  (You have access to set up the port-security 6500?)

  (2) fix the G2 interface configuration.  If you do not see the web interface with the Win 7 PC directly connected then there is something wrong with the config on GBA.

• Web interface error - could not contact the server at this time

  Hey all,.

  Immediately after completing the deployment of the new 2.1 UM I'm running an obstacle when connecting to the web interface. After authentication, with the web interface, I get the following when you select my user type (service provider or aggregator - anyone):

  

  I redeployed the VAPP twice is not a transient deployment problem. Networking seems fine - I can ping from areas on the Internet from the SUSE console. Not sure that this message refers on the 'server' is in contact with. It is deployed on ESXi 4.1 in a cluster vCentre vswitches standard, nothing special.

  Any ideas?

  Kind regards

  Daniel Whittaker.

  Daniel,

  When you get the message after installation, click OK and then refresh the page or click F5.  The message should appear is no longer.

  Kind regards

  David

• EA2700 - unable to return to the old Web Interface

  Hello

  I have an EA2700 that I am moving back to the old interface, however it error whenever I try to install the firmware.

  That's all that I always get this message:

  Unexpected error that the firmware update has failed. Please try again later.

  We encountered an unexpected error. If the problem persists, please visit our Technical Support site.

  I have reset the router several times, he turns off all night, re-uploaded the file several times and I am still unable to restore successfully. Sometimes she same error when I try to set the password of the router itself and I have to reset it again before I can use the interface.

  Was setup to give than to try, and Oh surprise when I connected to my router this time I was introduced to the classic web interface

  Among the updates of the firmware Failed must have actually managed, even if he just kept throwing error messages. To be sure, I re-flashed the old firmware from inside the classic interface and it worked perfectly without errors.

  At least I am now finally back to where I was before the clouds rolled in.

• Volume in Youtube after the update

  I'm running a fork chrome for a web browser. After the update to the latest version of Flash, my typical volume of Youtube in the order of 20% rose to deafening volumes. Try a variant of Flash version 10 returned the volume to a normal level.

  I found the problem (after a few months, huh). I had the audio channels in my 8 game system when I did only have stereo. I thought that there not matter since everything is not surround would be reduced accordingly.

• Trying to access Web Interface WRT54G

  Hi all.

  I have a Linksys WRT54G, and I try to access the Web Interface of the router. The problem I have is that whenever I try to access the Web Interface, the router stops internet connection for all devices connected to them, they are wired or wireless broadcasting. The only way for me to find the internet connection is to insert the SetupWizard disc and go back through setting all things.

  I need to access the Interface so that I can enable port forwarding.

  Any help would be greatly appreciated. Thanks in advance.

  Are you sure your firewall on the computer (including the Windows Firewall) is off?  Some firewall is very difficult to put out.  In addition, disable your pop-up Blocker.

  To make an update of the firmware (or re-install), you will need to use the tftp.exe program.  The instuctions throughout the proceedings (including the tftp.exe info) can be found here:

  http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=3703&p_created=11515...

  After the installation of the firmware, don't forget to reset the default router, and then configure the router again from scratch.

• WRT54G V6.0 Web Based Interface question

  I'm trying to set up a WRT54G. I ran SetupWizard which did not work.

  I can access the Web Interface to 192.168.1.1, but when he appears (after putting the admin password), the page does not load correctly. The colors and text appears, but all tabs, buttons, and links are missing (including the button Save the settings). I can't go to the Administration page to restore the default settings or update the firmware.

  I tried the pressure on the button reset for 30 seconds about 100 times so far and nothing has worked. I tried this on 3 different and executed my other computers 2 WRT54G correctly on all of these computers.

  I bought the router about 2 years ago and I just opened the box today.

  The fixes are available?

  Thanks in advance.

  Fantastic! It worked.

  Thank you.

• jumble of text in the web interface after Web Services update / firmware

  I received a message on the screen of my Officejet 6700:

  Update recommended

  An update is available for Web Services (ePrint and Apps).

  Do you want?

  I chose to update now and it installed fine, or so I thought.

  I checked the web interface of the printer, and there is a bunch of text confused, as the code is messed up for the web server.

  I had just finished to check the status of your ink cartridges (and subsequently replaced a), so I have the fully functional Web page fortunately still open on another machine, so I can tell exactly what is forward - after on this page.

  On the tools > gauge of ink page, on the right page (old) the said table (title, first line, first column):

  Cartridges installed

  Color | Magenta | Cyan | Yellow | Black

  Part number

  Type

  End of warranty date (A-M-J)

  First Installation Date (A-M-J)

  Area of ink

  USE

  HP

  But after the software update, it says this:

  Print the self-test Page

  L@S#0456 | Number of recorded events. L@S#0462 | L@S#0552 | L@S#0450

  Use of the accumulated media

  Date

  L@S#0477

  L@S#0561

  L@S#3345

  In addition, the order "supplies" link, with a contextual text of "print order supply."

  now, says "Cartridge", with a contextual text ' block unwanted faxes '

  And "Print Printer Status Report" now says "L@S#2567".

  I went to the support section and found an update firmware, but during download and execution, after you find the printer, he says that he is already up to date and leaves me not choosing to try and reapply the update of the firmware (as is obviously what is happening through the touchscreen menu has already done).

  Should I just restore to factory settings? I think that firmware would not be changed by doing this. It is not an older version of the firmware available on the product support page, to return to an earlier version.

  Via the screen menu touch printer, a Printer Status Report print indicates the firmware version is MPM3CN1322DR.

  How to force a reinstallation of the firmware, or let them difficulty firmware which was released on 25-06 - 2013?

  I've been using Google Chrome and even had 2 tabs open in the same window, one from before the update and the second I opened after the update, so this was not a factor.
  
  I had not revisited the web interface of the printer to date, and currently, I see that the problem has disappeared!
  The version of the firmware has not changed, and I did no manipulation of the printer. I also highly doubt that the main user has nothing, because it is not tech savvy. So, the problem seems to have corrected itself.

  The only thing I see now, that I did not notice before, is that there is a version of firmware fix, but it currently says 0. I don't know what it was before, but I guess zero means that there is a patch, so the firmware didn't automatically update in order to make the problem disappears.

  Problem disappeared, but I don't know how or why. I haven't decided if I will update the second printer that is the same model.

• SRW2016 Web Interface after Firmware Update error

  I have a new SRW2016 and after updating from 1.2.1 to 1.2.2 firmware I get an error trying to connect.  I use Firefox with IETab and the error message is:

  ... An error has occurred.

  ... You want to debug?

  ... Line 11

  ... Error: "tBodies' is null or not an object

  I tried to use Internet Explorer, but the status bar displays "error on page".

  I * really * need help!  Any ideas?

  BTW, I got the update of the firmware twice.  The first time was

  minutes and finally he stopped (I don't remember if there was a mistake

  message).  The second update seemed ends without problems.

  TIA

  Well, I was about to do the update with hypertermial/xmodem, when I thought I should check the browser interface.  And now, it's working now (even if it's really slow).

  He had to because of my recent update to Firefox v2 to v3, as well as the updated IE Tab addon.

  I hope that the web interface used the HTML standards and not require IE. It's very frustrating.

• WRT160NL cannot connect to the web interface after firmware update

  I've updated the firmware to unofficial http://mirwifi.org/download/fw/WRT160NL/wrt160nl-0.1.3-pre5.bin and since then I can not connect to the router through the web interface. What can I do? Is it possible to update the firmware to the official without web interface? Thanks in advance for any help.

  The router's default IP address is 192.168.1.1. Try to ping the IP address of the router and check if you get answers from the router.

  Open the Internet browser and in the address bar type http://192.168.1.1. See if you can open the router configuration page.

  If this does not work then you can try to update the official firmware on the router using the TFTP.exe file.

  Disable the firewall on your computer. Connect the computer to the router with the Ethernet cable.

  (1) download the official firmware file from the site Web of Linksys router. Save it to your computer.

  (2) download the tftp site Web of Linksys. Follow this link to search for the file tftp. You'll find downloads for router BEFW11S4. Select the version 3.2 hardware and download the installation wizard. Save it to your computer.

  (3) run the installation wizard. In the server box, type the IP address of your router. In the password box, type the password of the router. Default password for the router is admin. Find the file of the official firmware you have already downloaded and click on upgrade.

  See if it works.

  After upgrading the Firmware on the router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.