WRT54GS Setup on my office network

I work for a large company and want to reinstall my wireless router, so I move me from one room to the other with my laptop without plugging in our network. I had it put in place before, but had to spend an hour with technical support to set up the router.  Recently, I had to reset the password and lost all the settings.

I can get to connected to the establishment with the password by default but have no idea how to set it up. No matter what I try, I get no conectivity when I try to redirect the browser to the internet.

Yes, I know I should leave our network COMPUTING staff put in place, but they get all bent when I want to extend my wireless configuration access even if it is password protected. Can someone help me out here?

Thank you

Well, I use the router wireless wrt54G V8. Works the same as yours?

I just went by the addition of this router as a network wireless access point on my local network.

It's really quite easy once I realized a few things.

First, you will need an IP address for the router to entrust your IT
people. If you are not going to be able to get it, I'm not sure what you can do.

IP address of the router is 192.168.1.1 default. Assuming you reset him

router by default, simply connect a cable to one of the router's Ethernet

ports (not the Internet port) and connect the other end to a laptop. The router will

power to the laptop with a IP address and you will be able to run a browser for

http://192.168.1.1 to access the router administration pages. The connection on

my router was admin with a password of admin, but I've seen people from Linksys

say other things, so this cannot be true for all models of router.

Once connected to the administrative pages, you can assign any IP address

you want to the IP address of the router. You will see the default 192.168.1.1 in

There now.

Assuming that your IT people assign you a static IP address of 192.168.135.37 (or

whether it is), then you'll want to assign as the IP address of the router in the

administration pages. Note that once you do this, you will not be able to talk

the router via your mobile phone directly connected any longer. You will need to

Always connect the router to your office network - via one of the Ethernet ports

(not via the Internet port).

You may need to reset the router after changing his IP address, even if

I don't have to do it on my own.

With the router connected to your office network, you should be able

to access it from any PC connected to the network in exercise, by

Navigate to the IP address assigned by IT (in my example 192.168.135.37

(See above).

Now you can activate the wireless network, assign a security mode.

passwords/pass phrases, etc.

When wireless devices negotiate security of your wireless router,

they will act as if they were connected directly to your desktop in

network.

I can provide more details, if you wish. Perhaps by PM?

Let me know,

Tags: Linksys Routers

Similar Questions

  • 4 Apple TV on my office network, get conflicts of IP addresses between them despite being assigned to the reserved addresses.

    4 Apple TV on my office network, get conflicts of IP addresses between them despite being assigned to different addresses reserved in DHCP

    Although it seems that they realize and correct this means my network notifify me of the conflict and that can mean more than 30 emails per day... and on a long weekend which means 90 more e-mails to remove after it making sure it is the same 4 mac address having problems... How can I do that, go away

    Given that you are reserving DHCP addresses, I suppose that you have set the ATV to get automatically addresses. That should work.

    Are there opportunities that they are waking up on WiFi and Ethernet switching? On may switch from one WiFi network to another?

    Do you really need fixed IPs?

    The alternative to the reserved addresses would be to reduce the size of the DHCP pool and set the address, staticly ATV.

    Just by the way, have you given the names of different ATV? This is necessary for the Apple protocols.

    Can you identify the versions of your ATV, see identify your model of Apple TV - Apple Support?

  • Printer network 160 E - studio does not work in my office network

    Hi Toshiba team,

    I ' v got a Toshiba e-studio 160 network printer/scanner/fax in my office and I want everyone in the office (network) has access to the printer and scanner functions of the e-studio without using a computer 'server' that must be connected to the local parallel port of the printer. In other words, the printer is connected over TCP/IP and a RJ45 cable to my switch to the office.

    The printer configured with a valid IP address, but in my Office I havn't no matter what WINS server, the configuration field is empty and unused ones. I tried several different methods, but I can't access the printer via TCP/IP. Just the 'PING' command works correctly. I expected that the printer appears in the Windows file sharing folders, but it doesn't. Furthermore, all my computers are equipped with Microsoft Windows XP. I read somewhere in a Board of Directors that a guy has solved this problem by using a program called "P2P", but I couldn't find something like that.

    With original Toshiba drivers, it is only possible to exploit this local printer or on a print share Windows function, but I don't want that a machine is running all the time.

    I hope someone can help me with my problem.

    Best regards
    Michael

    Since it is a forum only for computers laptop Toshiba and Options, I doubt that someone will be able to help you.

    But I found a special page to Toshiba for printers and copiers.
    http://copiers.Toshiba.com/support/index.jsp

    You might find a few details here.

    Good luck

  • How to install an office network share drive?

    I would like to know what is the best way I can configure a share of office network drive so that everyone can access and store their working papers, so we're all on the same disc?

    Objective:
    I want to the control user that has read/write access to the files on the shared disk, but I don't want to create a separate user on the host computer for each person. Also be able to access the drive via the vpn for home/away.
    Current configuration:
    Our network configuration:
    Building (several companies housed under the same roof) > wired Ethernet > suite > router > 10-15 devices (computers laptops, computers, phones, printers, etc.) wireless
    Share drive host computer:
    -Ultimate windows 7
    -Connect to a router via gigabit ethernet
    -A a static ip address lan internal 192.168.1.xxx.
    -1 TB drive on here to be used as a shared drive
    -2 TB drive will be backup to a separate computer that is not used
    All computers run windows 7 Professional/ultimate
    Wireless router is also assigned a static ip address of the office building.
    I don't want to use the homegroup, but perhaps workgroup would meet my needs? I can't currently office and vpn remote access into the host computer, but only one user can access the drive of course if they are not in the Office in this way.
    I can map the drive network internally, but not outside. I re - map every time at home if I want to use the VPN.
    Ideas or suggestions for this type of configuration, a NAS system?

    Hey Joe,

    I would recommend you to view the query on the TechNet Forum which, I am sure, will help you better. Click on a question and post your question.

    You can check the link to the request message:

    http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

    Email us if you have any further questions. We will help you.

  • Just added a windows system 7 to my office network have permission issues accessing the Server 2003. Connects but does not trust the server

    I just added a windows system 7 to my office network. It will connect to the server. QuickBooks can access data on the server, but Microsoft Access is not - says that the file is located outside the intranet.

    Hello

    Thanks for posting the request in the Microsoft community!
    Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet forum
    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  • Change the view office networks

    I'm changing my view office network, i.e. taking them out of the Nexux 1KV and put back them on the standard switch.  It seems that I can't change the image of «replica...» ».  Do I need to recompose the workstations?

    It's graceful in my opinion, maybe a powershell script to change via the network on the clones, until you're ready to recompose.

  • WRT54G Setup for internet access using Lacie Network Space Max

    Help, please!

    I tried for the past 2 weeks, try to configure my WRT54G Router, so it allows me to access the Lacie on the internet without success. I followed all the instructions of Lacie and all other FAQ and help on the internet, still no luck. I spent several days with Lacie tech support and they could not understand it - why my router would allow me access via internet. I hope that the big guns here can help me.

    I have a number of laptops connected to my local network and all wireless laptop can access the NAS Lacie cable to one of the ports on my router. My whole system works wonderful locally.

    The Lacie received a static IP address to 192.168.1.199

    My local network has an IP departure from 192.168.1.150 and ends to 192.168.1.199

    My router IP is 192.168.1.99

    I've assigned port forwarding to my Lacie (192.168.1.199) for ports

    20, 21, 25, 80 and 443.

    I tried other settings but no help. Help, please!

    Happy new year!!!

    Hey Scrooge.

    Thanks for your help... my SIN was in fact all along. I used my cell phone to connect to all this time. Today, I tried my work PC to connect using ftp://x.x.x.x and it is well connected.

    I appreciate your help and your patience.

  • WRT54G will connect to the network but will not connect to internet

    Guys, I installed an older Linksys CM100 cable modem and when I did I lost the connection to the internet using the WRT54G Router. I can connect fine net when I go to right fromt the modem cable to the pc. I can use my home network very well. I did a firmware upgrade, does not. I'm losing my mind. It worked fine before the new cable modem. Does make sense to anyone? BTW, I can't connect to the internet via wired or wireless connections and ping www.google.com gives 100% packet loss. Ditto for a ping to 192.168.1.100 (cable modem) when the router is connected.

    Dear God please help me

    -Jacob

    Thus, because no one here was able to offer all the help, I called tech support and was very surprised. I was able to get a tech immediately and without going through the 1 million on the phone buttons. The service is in India, but I could communicate well enough with him, even though I usually have people of understanding of handful who speak English as a second language. The issue that I had was that the default IP of the modem cable (192.168.1.100) and ip address of the router (192.168.1.1) were too similar. Apparently, the fact that the 3rd number 1 for both series was the cause of the problem. We changed the IP address of the router to 192.168.5.1, power cycling it and unfortunately it worked.

  • WRT54GS Setup

    I have a D - Link DI-514 now hung. I bought the WRT54GS and want to replace the D-Link router. I have a Motorola Surfboard SB4100 modem cablel.

    I followed the instructions of the Setup disk. He got to step 4 and then just sat there for a while and said there was an error 322 newrouter or a bridge not detected. I tried again but get the same error. What can I do to fix this error?

    I made a call to the technology free toll-free support number. The installation instructions are different, then those who are on the CD that came with the router. I followed the instructions of the tech support and the router works fine.

  • Remote office - network level authentication

    Hello people, hope you can help!

    I have a laptop running vista professional and a desktop running vista ultimate.  On my desk, I activated remote desktop access and can rdp on the desktop from the laptop when the median option button is selected "allow connection of computers running any version of office to distance"... however... I obviously want to use network level authentication to be sure that I can access the office using my connection wireless laptops.

    When I try to do, I get the usual message, saying that "the remote computer requires network level authentication, that my computer does not support.    Curiously, when I try the other direction (from the desktop to the laptop), I have access! How is it?  I checked the windows features that are installed and they seem to be the same...

    Hello again,

    I double checked everything and both machines as set identical upward (as far as RD is concerned).  Both machines now have a user account called RemoteDesktop with a password, the two machines are set to "Notify me" and that the two computers are on the same workgroup.  Everything seems very strange to me.  If one of the PC did not support NLA, then it should not work at all, so it makes no sense that it works one way and not the other.

    That being said, What are the risks of a lower level running on a home network? The network is secure (or as secure as possible never) so what are the differences between the two settings?

    On your LAN House I would be worried about this. Its pretty hard to fake an address on the network under your control especially if your behind a router (with firewall function) and your wireless network is secured. I would, however, high encryption necessary and always warn the client for a password, sign in.

    http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6ConfigRecommendations.html#host

    FWIW, I regularly connect to desktop computer XP Pro to my wife and a Windows Home Server with Remote Desktop [DRC] a computer laptop Vista Ultimate or Win7 RC1 and Ubuntu. None of those taking support NLA mode server host/DRC. The Ubuntu laptop does not support the NLA in client mode DRC.

    That said, is the customer who cannot not configured like that? I believe that this is the default condition.

    http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6-09.jpg

    Also, just for the sake of the information that the failing client shows the extent of the support NLA. The built-in client for Vista should indicate this.

    http://windowshelp.Microsoft.com/Windows/en-us/help/ea4680d1-6962-463b-B29B-351efa676f9e1033.mspx

    I assume that your market SP1 or SP2 on the Vista client, which is a failure and have not tried to download and upgrade the remote desktop client.

    There is also this lengthy thread which can be interesting. Not exactly your question but interesting nonetheless. Bottom line is to make sure that the time is correct on all machines. There is also a procedure to remove the server/host certificate which you could do a test.

    http://social.answers.Microsoft.com/forums/en-us/vistanetworking/thread/4ab6c1ba-13ed-4b0a-b5ba-601e2b0a28d7

    MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

  • My office network change constantly 2 to 3 to 4 to 5 several times during the day.

    I have 5 desktop wireless computers connected to my Server EHR through FIOS and changes in office constantly network since network 2 to 3 to 4 to 5 to 6-7.  My staff is unable to access the necessary software from the server, and it is VERY frustrating that this happens.  How can I delete all networks, except that I want my other computers to join?  Other computers are wired with Linksys and its small modems.  Help, please.  Go crazy.  Sharon

    Hello Sharon,

    Thanks for posting your query in Microsoft Community Forum. However, the question you posted would be better suited in the TechNet Forums.

    This is why I would recommend posting your query in the TechNet Forums.

    TechNet forums

    Thank you.

  • Security issues with SMB concern files MS Office network locations

    On our windows 7 machines of our users we have problem of slowness of opening Office files from a network location

    This slowness only affect the users in the domain.  Domain Admins have no problem of slowness.

    Changes to approved documents ro trust location.  Location of trusted network has no effect.

    If I disable SMB users in the domain can open network location with no slow Office files.

    Any ideas?

    This issue is beyond the scope of this site and must be placed on Technet or MSDN

    http://social.technet.Microsoft.com/forums/en-us/home

    http://social.msdn.Microsoft.com/forums/en-us/home

  • Office network disconnects and refuses to connect.

    Original title: network path cannot be found/nom_peripherique unrecognized - peripheral network disconnect themselves, do not share network

    Our firm has a network that connects the main CP in the conference room with the printer/scanner and all other PCs in the office. Recently he started to disconnect randomly various devices, why is this? Once, it disconnects often refuses to recognize other devices on the network names or indicates the network path was not found. Why is it a few days and then all of a sudden a computer disconnects? Is the wifi modem on our pc reception causing th eproblem because its old? the firewall settings cannot be because most of the affected epcs th have active firewall? Please help, it is really hard to share information at the office without the network and even more difficult when the internet refuses to connect as well!

    Hi Maxine,

    Welcome to Microsoft Community where you can find all the answers related to Windows.

    According to the description, it seems that you have a problem connecting to the other computer in a corporate network. This problem is linked to the domain (company network), you can contact the administrator of the network of the office or write the topic in the Technet Forum for better support.

    Visit this link to report the issue in the Technet Forum.

    Hope this information helps. Answer us queries windows and we will be happy to help.

  • Setup of Microsoft Office 2016

    I was installing Microsoft Office 2016 on my Macbook Pro (mid-2010, processor 2.4 GHz Intel Core 2 Duo, memory of 4 GB 1067 MHz DDR3, 46,72 GB of storage, OS X El Capitan) when it froze at 'Execute the Scripts in package' I waited for about half an hour, and he has not yet changed. I tried to restart my computer, but that didn't work. I don't know what to do. Please help quickly, I need Office for my school work.

    You must have the latest version of Mac OS X installed 10.11.6. Restart your Mac and then reinstall Office for Mac 2016. As soon as you get it installed, make sure that it contains the latest updates.

    To 2016 Office, select the instructions section, select Office for home - install on a Mac.

  • HP OFFICE NETWORK CONTROLLER MISSING IN DEVICE MANAGER

    I can't connect to the wi - fi network because the network controller is missing in Device Manager. Please help with link where I can download the right software to. My hardware ID as it is in Device Manager - Properties - Hardware ID is

    PCI\VEN_1814 & DEV_3060 & SUBSYS_3C041186 & REV_00
    PCI\VEN_1814 & DEV_3060 & SUBSYS_3C041186
    PCI\VEN_1814 & DEV_3060 & CC_028000
    PCI\VEN_1814 & DEV_3060 & CC_0280

    Please I need help fast.

    Thank you

    Hello

    the drivers are here.

    You don't specify what operating system is installed.

    Is a HP 500 b, your desktop PC?

    Best regards

    ERICO

Maybe you are looking for