WUMC710 lost connection

Similar Questions

• Keyboard Smart ipad pro, lost connection

  Hello

  Why my smart keyboard sometimes lost connection with the pro 9.7 "ipad. Then after rebooting the ipad it works again. But its always like that. Is there any problem or how to fix it?

  Thank you

  Hi Budi73,

  Welcome to the communities of Apple Support! I'm sorry to hear that you are having these problems with your iPad Pro and your Smart keyboard. Since the Smart keyboard uses the contacts of the Smart connector on the side of your iPad Pro, if you are having problems with intermittent or loss of connections, you can check the contacts as described in the following article:

  Get help

  If your iPad Pro does not detect your Smart keyboard or you see an 'Accessory not supported' alert on your iPad Pro, make sure that there are no debris or plastic on the pins of the Smart connector on the keyboard or the Smart Connector on the iPad Pro. Also, try the following steps:

  1. Make sure your iPad Pro and Smart Keyboard are in a position to Type .
  2. Remove the Smart keyboard for your iPad Pro.
  3. Restart your iPad Pro.
  4. Reconnect the Smart keyboard.

  Use your Smart keyboard with iPad Pro - Apple Support

  Concerning

• Lost Connection using the Magic Mouse

  For a week, whenever I move the mouse, it freezes with a pop - up message "lost connection".  Click again and the connection is re-established.   I replaced the batteries, but the problem persists.  This week, the problem got worse. All solutions?

  Hello Carolyn,

  Can you tell me a little more about your mouse and the machine that you are using.   Your profile says you're on 10.5.8 which means that you use the system to Leopard.   Is this correct?

  Can you tell me what brand of batteries you use and whether they are regular or rechargeable?

  If you hold the mouse upside down is the flicker of green light or is it stable?

  If you shake it is there any noise from traffic on the inside?

• My mouse wireless guard saying lost connection.  I thought that it may need a new Bluetooth card.  An idea of the cost if I do it?

  My mouse wireless guard saying "lost connection".  It takes time for it to reconnect.  Wireless keyboard is OK.  Apple store said that it may need a new Bluetooth "card."  Any idea the cost if necessary.   I tried a new mouse, with the same results.  Having to use a "wired" mouse now taking a much-needed port on my iMac.

  I return to the store and get a better answer. Material, of course, could be the problem. As far as I know, there is no such 'map '.

  Reset the PRAM and SMC... can't hurt, might help.

  Barry

• Windows Server 2012 lost connectivity

  Hi all

  I created 6 virtual servers Windows Server 2012 R2 Standard. However, there are 2 weeks 3 to 6 servers randomly lost connectivity (ping returned request) outdated, unable to control remotely,... several times until I have restart servers, connectivity was back. Even if 3 other servers do not have this problem.

  I found the following error events in the event viewer, I don't know if they cause this problem or not:

  Log name: System
  Source: Schannel
  Event ID: 36888
  A fatal alert is generated and sent to the remote endpoint. This can lead to the termination of the connection. The defined protocol TLS fatal error code is 40. The Windows SChannel error state is 252.

  Reference: https://msdn.microsoft.com/en-us/library/windows/desktop/ms678421(v=vs.85).aspx

  -------------

  Log name: System

  Source: NETLOGON

  Event ID: 5719

  This computer was not able to set up a session securely with a domain controller in the domain GHPFE because of the following:

  Currently, there are no available connection server to process the logon request.

  This can lead to authentication issues. Make sure that this computer is connected to the network. If the problem persists, contact your domain administrator.

  MORE INFO

  If this computer is a domain controller for the specified domain, it puts up the session for the specified domain PDC emulator. Otherwise, this computer sets up the session secure at any domain controller for the specified domain.

  Reference: https://support.microsoft.com/en-us/kb/938449

  Microsoft warning serious problems can occur if you modify the registry incorrectly by using the registry editor or by using another method. These problems may require that you reinstall the operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.

  -------------

  Log name: Application

  Source: CAPI2

  Event ID: 4107

  Has not taken from the root list third-party auto update cab at: http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab> with error: these data are incorrect.

  Reference: https://support.microsoft.com/en-us/kb/2328240

  -------------

  Log name: System

  Source: Client DNS events

  Event ID: 8015

  The system cannot save the host (A or AAAA) resource records (RR) for the network adapter

  Reference: http://support.simpledns.com/kb/a182/system-failed-to-register-host-resource-records-rrs-network-adapter___-warning-windows-event-log.aspx

  -------------

  Log name: System

  Source: Group policy

  Event ID: 1054

  The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Check your service provider Internet (DNS, Domain Name System) is configured and working properly.

  Reference: https://support.microsoft.com/en-us/kb/324174

  Microsoft Cause: This problem may occur if the address of a preferred DNS server configured on the client is invalid or is inaccessible.

  -------------

  Is there anyone know of this problem and the resolution to it? Help, please.

  Thank you

  Khiet Manh

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• HH.exe crashes - lost connection to the online help and Support window

  HH.exe crashes - lost connection to the online help and Support window

  SYSTEMATICALLY, FOR MONTHS, WHEN I SEARCH WINDOWS HELP I got THE MESSAGE.

  "You have lost your connection using Windows and Support website. . Try to connect again. "
   

  Windows Error Reporting shows several times:

  1. HH.exe hangs and does communicate with Windows
  2. MsSearch TerminateProcess & #x000d
  3. ApphelpSoftBlock & x000d #.

  I have no problem connecting to Windows Web sites otherwise or to other sites on the web.

  Can someone tell me how to fix this?

  (I'm running VISTA 32 bit)

  Hello

   
  This behavior is caused by a corrupted or damaged HH. DAT file.
  
  This may occur if Antivirus or a firewall, you have installed the program it blocks.
  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks

• I get an error message: The Nvidia OpenGL driver lost connection with the display driver and can not continue. Error code 8

  When I play the virtual Interactiver - Second Life Community. The screen turns white and windows tells me the display adapter stopped responding and has recovered. While the second life Viewer is still Virgin (white). I get the error in a box: The Nvidia OpenGL driver lost connection with the display driver and can not continue. The application must close. Please visit http://www.nvidia.com/page/support.html for help. Error code 8. Now, I worked with Nvidia to do a clean install of the latest version of the driver. a driver in safe mode installation. They suggested to try an earlier version of the driver. Nothing that they worked me and told me to see Microsoft. The pilot hangs every 30 min or so, all online in the second game of life. Can someone help me?

  Information System
  ------------------
  Time of this report: 13/06/2011, 19:40:20
  Machine name: BEN - PC
  Operating system: Windows 7 Professional 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.110408) - 1631
  Language: English (regional setting: English)
  System manufacturer: HP-Pavilion
  System model: GC670AA-ABA a6120n
  BIOS: Phoenix - AwardBIOS v6.00PG
  Processor: Intel (r) Core (TM) 2 Duo CPU E4400 @ 2.00 GHz (2 CPUs), ~2.0GHz
  Memory: 4096 MB RAM
  Available OS memory: 3582MB RAM
  Page file: 1690MB used, 5472 MB of available space
  Windows Dir: C:\Windows
  DirectX version: DirectX 11
  DX setup parameters: not found
  User DPI setting: 96 DPI (100%)
  System DPI setting: 96 DPI (100%)
  DWM DPI Scaling: disabled
  DxDiag Version: 6.01.7601.17514 64 bit Unicode

  Two monitors

  Display devices
  ---------------
  Card name: NVIDIA GeForce 7600 GT
  Manufacturer: NVIDIA
  Track type: GeForce 7600 GT
  DAC type: Integrated RAMDAC
  The device key: Enum\PCI\VEN_10DE & DEV_0391 & SUBSYS_201F19F1 & REV_A1
  Memory display: 1768 MB
  Dedicated memory: 248 MB
  Shared memory: 1519 MB
  Current mode: 1600 x 900 (32 bit) (60 Hz)
  Name of the monitor: generic PnP monitor
  Monitor model: G205H (Acer)

  Card name: NVIDIA GeForce 7600 GT
  Manufacturer: NVIDIA
  Track type: GeForce 7600 GT
  DAC type: Integrated RAMDAC
  The device key: Enum\PCI\VEN_10DE & DEV_0391 & SUBSYS_201F19F1 & REV_A1
  Memory display: 1768 MB
  Dedicated memory: 248 MB
  Shared memory: 1519 MB
  Current mode: 1280 x 1024 (32 bit) (60 Hz)
  Name of the monitor: generic PnP monitor
  Monitor model: NEC LCD7V

  Hello

  I suggest that you have watch the following link below:

  http://forums.developer.nvidia.com/index.php?showtopic=5331

  I hope this helps.

• VPN client, lost connection

  Hello

  I pix506e here... and vpn clients connected.

  But suddenly lost connection vpn client 40 minutes and then try to reconnect again but fail. If the vpn client restarts their pc/notebook...yes it can connected to vpn again... but the interruption of the connection again... then restart... and so on... What is the cause of this problem?

  Thanks for the help

  Tonny

  All remote VPN clients are having the same problem or is it limited to just a few. If the problem is seen with only a few, it is quiet possible that the problem is not with the PIX of the customer. In addition, the DPO is enabled or not. DPD will cause tips to know an IPSec connection over, where the SAs flusing, allowing new being negotiate quickly.

• Passport BBM - BBM has lost connection. Error

  Just got a new passport BB yesterday and followed the installation procedure.  After that I get the main phone, I tried to access BBM. Initially, he showed a screen with stickers and a few links ToS and EULA. Once hit accepted, he deleted and after a few minutes, shows the error message: "BBM has lost connection. Can not connect to the server.

  It is on OS 10.3. 0 675

  and BBM version 10.4.4.8 (everything has been updated during installation)

  The only thing that I could find on the database has information about a building of BONES cast in 10.2

  Hi @fj_langlais

  Can you check to see if you get the same error when you check the software updates?

  Using a new BBID or one that has been linked previously to another device?

  Do you know if you are connected to the BlackBerry Internet Service? You should see the BlackBerry Logo next to your signal at the top of your home screen indicator.

  Can you try to send a PIN message?

  1. open the Hub and select "Message of PIN.

  2. Select "dial."

  3. Enter your PIN in the field "to".

  4. press on "send".

  Note: To find your PIN go to settings > topic > category > hardware

  If the fails to send a PIN message recording unit to try to give, the following BlackBerry Knowledge Base Article explains how - KB00510: how to register a BlackBerry smartphone with wireless network

  Once you have done that try yourself send a PIN message a second time, and see if its sent successfully.

  Let me know how it goes!

• HP DV6T-1300 lost connectivity to the internet, error display 701

  I have a laptop HP DV6T - 1300 Entertainment who has lost connectivity to the internet, and it displays error 701. All of my diagnostic checks, I think that he has lost the pilot because he does not have a wireless card. I downloaded the drivers wireless (five each) HP support and assumes that the Realtek driver is the original. What is the purpose of all other drivers (Broadcom, Atheros, Wireless & Bluetooth Pro) and they need to be installed or not? They are updated day or improvements or are drivers for the other cards in different models of this computer? I use the laptop for my wife to access the net until I fix this. Thanks in advance!

  After that to install the Realtek driver (original), I discovered that the software does not recognize that there is a wireless card. In my view, the map is part of the motherboard and may have failed. I suspect that my best solution may be to buy an external wireless card and install it. Any suggestions?

  I don't know exactly what happened, but after restarting a couple of times, the wireless card started working again. He works actually better than what he has. The downloaded driver was an updated version, and this may explain the improvement.

  Different cards for different models of different computers in your model class.  You only need the driver for your system.

  The updated driver for your model of correction probably your problem.  The fact that it works better than before is, of course, a plus.

  If you don't already have it, here is the wireless connection manager:

  HP sp54945 V4.1.25.1 Connection Manager

   

  Connecting to a network with the 4.x connection manager

   

   

  For your reading pleasure:
  

  Domestic use Wireless-G and Wireless-N devices on a network

   

   

• I can't install Adobe Flash Player.  I have windows 7 64 bit and firefox browser.  During installation, that I get a message "lost connection", followed by "trying to reconnect", then cannot connect

  I can't install Adobe Flash Player. I have windows 7 64 bit and firefox browser. During installation, that I get a message "lost connection", followed by "trying to reconnect", then cannot connect

  Please use the Offline Installer

  Internet Explorer:

  http://fpdownload.Macromedia.com/pub/flashplayer/latest/Help/Install_flash_player_ax.exe

  Firefox and other NPAPI browsers:

  http://fpdownload.Macromedia.com/pub/flashplayer/latest/Help/install_flash_player.exe

• Lost connection issues

  Hello

  I desperately need help.  I tried to update my adobe flash player, but he kept getting 33% and then he said that it has lost connection (I know that there are no problems with my internet connection at the moment).  I tried saving the file on my file to download and then running and now tried to uninstall and install it... and the same thing again and again, I'm stuck at 33 percent.  Now, I have no drive at all because of me that I had the uninstall.  Please please help

  Installers in offline mode:

  • Flash Player for Internet Exporer - ActiveX
  • Flash Player for Firefox - NPAPI
  • Flash Player for Mac OS X

• Installation of flash player dies at 33% lost connection, can not reconnect

  WinXP

  Tried FF, IE, Chrome.

  Tried to uninstall, clear cache close all browsers

  Tried to download the NPAPI to install direct link (still trying to download after 5ish minutes)

  Whenever I get the same result; It downloads, start installation then loses connection and cannot reconnect.

  Help!   Please, I beg you.

  Hello

  The installer of the hold (as indicated by the screenshots) downloads / installs Flash Player silent mode.  Connection/network latency problems can lead to lost connection.  The full download installers the entirety of the original file and launched once do not make any other downloads in the background.  If you encounter connection/network latency problems, please try to download the full installation programs displayed at the bottom of the of installation problems. Flash Player | Windows page, in the section "problems".

  --

  Maria

• boring data lost connectivity alerts

  When I go into a building where my cell phone reception is weak, I have an alert 'data connectivity lost' even if I have a wifi connection works. I would like to disable this alert, but I can't find anywhere to do this.

  If you go into settings, sounds, in there, you will find your lost network.

  Clear the check box next to it, and you should be all set.

  Thank you

  J

  Sent from my Motorola Photon 4 G

• I lost connection on the computer like many light wireless wireless router.

  I've got three Kindle and a laptop computer, more my PC connected

  Original title: I lost my WiFi connection at home in light of the route for the wireless is not lit.

  Hi geraldthorpe,

  Thanks for posting your query in the Microsoft Community. It seems that you have no internet connection on the computer. We can get this fixed number by systematically. It can be frustrating for you. But, don't worry, we're here to help.

  We start with a few questions-

  (1) what is the version of Windows installed on the computer?

  (2) you are able to connect to Internet via LAN cable?

  (3) are other computers at home able to access Internet?

  (4) do you get any error code or error message?

  (5) have you made changes on the computer?

  I would like more information about the issue.

  Method 1-

  As a general rule, if the wireless light is not on the router means that the ability of routers to transmit wireless is lost.

  The router has generally, 4 types of fires.

  Power - number 1

  Test - number 2

  Wireless - number 3

  Internet - number 4

  Numbered LAN are turned on only if a network cable is connected.

  If the computers are connected wirelessly, all the lights except the indicator light should light up.

  I wish you perform a reset and a cycle of power to the router.

  Reset the router-

  You must locate a set PIN size behind the router and press the reset button with a pointed object for 10 seconds. Now, release the button and wait for the lights to come back.

  Note If the wireless light is back on.

  Power cycle-

  I wish that you unplug the router from the power outlet main and plug it back again.

  Check if the problem persists.

  Method 2-

  I would have you look at the article-

  Network convenience stores

  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Method 3-

  I would have you look at the article-

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Wireless and wired network problems

  http://Windows.Microsoft.com/is-is/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  We know if you need help. We will be happy to help you.

  Thank you.