Y50 stops after bios update

Similar Questions

• System stopped after bios update (Y510)

  I've updated my bios on xp using the vista Installer (probably a bad idea). Just after I've updated, to start the system stops. Saying: network wireless unsupported detected device. Arrested system. Right now I can't do anything on this subject. Little help would be greatly appreciated.

  You can find the location of the map by turning around the laptop and by unscrewing the largest coverage (coverage that doesn't have a disk written on it).

  http://img208.imageshack.us/img208/9977/dsc00656iv0.jpg

  It should be the thing circled in blue. Read the label on. Find a way to remove this card from the system. I have no experience with the removal of the card itself, so I can't help you with this part.

• Laptop HP OMEN - 15-5010nr: Omen HP 15: backlit keyboard does not not after BIOS update

  This morning my HP omen arrived by mail, fully functional with everything in tact. After I left my laptop to install the updates from HP Support Assistant (one of these being an update of the BIOS updates), I returned to find my computer restarted and my enlightened retro keyboard does not. After trying to use HP OMEN control to fix the keyboard, I found the keyboard flashes when I click "Apply to all Zones", but then immediately turns off again. Is it possible to fix this keyboard backlit ir question can we see an update in the near future that resolves this problem?

  Found a solution! Apparently, the keyboard stops after the update of the BIOS, so to reactivate just push F5.

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Satellite C55-A-16Z - graphics card does not work after BIOS update

  Hello

  I have a portable Satellite C55-A-16Z with windows 8 and a Nvidia geforce 740M graphics card.

  Last week he asked me to update the version of the bios at 1.30.
  The bios update was successful.

  However when I restarted my laptop I started having a BSOD dgxkrnl.sys.
  Correction of the error and restarted for an another BSOD Windows, and after the second solution, I stopped making BSOD.
  But now, I noticed its games running, if not use the dedicated card, but use the 4000 Intel.

  In the settings Nvidia dedicated card is configured to be always on.
  It seems that my card is missing, but it appears in Device Manager.
  I tried to delete, update the drivers and the default factory reset, but nothing helped.

  Also, when I go into Options power the Intel card is listed and when I disable the card intel in the Device Manager it starts to use the graphic viewer for windows.

  How can I get my Nvidia card to work again?
  Any help is appreciated.

  Thanks in advance.

  Hello

  After the BIOS update the BIOS should be set to default settings.
  You can do it in the BIOS.

  In addition, you mentioned that Windows 8 is still installed on your laptop.
  8.1 to win has already been published by Microsoft and I highly recommend that update you the system of 8 to 8.1 Win Win.

  Before you start the upgrade to 8.1 win, you should check and read the instructions step by step for Toshiba: http://www.toshiba.eu/innovation/generic/windows8_1-message/

  I guess that after the Win 8.1, nVidia graphics card upgrade works well also.

  Your comments would be greatly appreciated.

• Satellite Pro A300 - touchpad failed after BIOS update

  After that good BIOS update 2.00 to 2.10 / suggest by ALERT TEMPRO - http://support1.toshiba-tro.de/tedd-files2/0/bios-20091125132031.zip/ the touchpad of my Satellite Pro A300 - GR 1 stopped working.
  He appears under the name hidden in Device Manager. The State of the device - "this device is not present, is not working properly or is not all its drivers installed." (Code 24) "reinstall the driver has no effect of course. I can also access the BIOS utility when you start pressing F2.
  Running Vista Business 32-bit Edition.
  Ideas to solve the problem will be highly appreciated!

  Hello

  Normally, it should be possible access the BIOS, if you press F2, once you have turned on the laptop. Please check again and load the default settings there.
  And you cannot access the BIOS if you shut down the computer.

  You can use an external mouse on the laptop? Please check this too.

  I've also updated the BIOS on my Satellite A300 but I n t have a problem with the touchpad after the update.

• Satellite M100 - no speakers sound thorugh after BIOS update

  Hi all

  I have satelite M100 PSMAAA-02006 with XP. I just updated the Bios on V3.0. Speakers do not work after update but the audio jack works so with headphones I can listen to but not through Laptop speakers and the keys to media on top of keyboard play, pause, stop, next, back, etc. homepage react too much.

  Someone knows the solution to this issue. Or is it possible to get the old BIOS? Although I not sure aboutt previous version.

  need quick help. Please answer as soon as possible.

  Thanks & best regards...

  Hi Julie,.

  I doubt that this was due the update of the BIOS. Is that what you have loaded default settings after updating the BIOS?
  Have you chosen the correct BIOS update?

  Normally you can hear the sound on the speakers laptop if you disconnect the headset. Make sure that the sound is not muted, you can do this with the FN + ESC key combination.

  About the multimedia keys, I would recommend reinstallation of Toshiba common Modules. You can find it on the Toshiba site.

• Re: Satellite - blue screen after BIOS update

  Hello

  My computer laptop girls worked very well until I did the BIOS update this morning. Now, I get the blue screen of death STOP: 0X0000007F. Help, please

  concerning

  Carol

  Hey, Carol, welcome to the forum! :)

  Don t misunderstand me, but may I ask why you n t post more information about your problem?
  Important to know is that your laptop you have exactly and where to download the updated BIOS and for what model. This is important information.

  By the way: have you ever tried to load the default settings in the BIOS after update?

• Satellite A500 - overheating after BIOS update to 1.50

  Hi, I hope someone can help me.

  I updated the Bios to version 1.50 a few days ago and now the laptop overheats and stops after a few minutes, when I play a game (Day of Defeat Source btw, it is not the newest and shouldn't be a problem). This problem occurred for the first time after the update. There was no problem with the temperature with V1.20 before.

  Is it possible to downgrade the bios V1.20? Where can I download the necessary file? I can just download the latest version on Toshibas website.
  I have already asked the support of aid, but they did not send me a response up to now...

  Thanks for your replies! :)

  Hi Flex Barker,

  Are you sure that this problem is really caused due to update BIOS? Normally, these overheating problems are caused by the old thermal grease or dust often due to the radiator. In my opinion, you should try to clean your laptop using a jet of compressed air. This could blow out the dust from the cooling fans.
  Check this box!

  Downgrade of BIOS is normally not possible. Older versions of BIOS, you can get your local authorized service provider. :)

• Re: NB520 - buttons on the touchpad does not work after BIOS update

  Got my NB520 yesterday and installed all windows updates, and then the BIOS updates proposed by the action center of Toshiba and after that the two touchpad buttons have stopped working.

  They did before. Any ideas whats happened, this is the update of the BIOS?

  I put t know if its the related issue of the BIOS, but if there is no way to get buttons working again I recommend you reinstall the OS using the recovery mode. Test the functionality of buttons with the factory settings.

  By the way: touchpad works properly?
  You can use an external mouse correctly?
  Have you checked all the settings of the touchpad?

• Satellite L30 - 14F - battery low CMOS and delivers after BIOS update

  For 1.5 years, I have a Toshiba Satellite L40 - 14F PSL4CE.
  I encounter the error of CMOS LOW battery but I was unable to find to replace. Where he is?

  Second problem: after a BIOS update (version of the site) with the same setting in Windows XP, after I left the lid downwards and then save the workbook hesitates for about 2 seconds and the music stops. These problems were not present before the BIOS update.

  Thank you for the cooperation.

  Hello

  The BIOS battery can be replaced by only authorized service. to do this the laptop everything must be dismantled. By the way: see s operating manuals. You will find info how to load the BIOS battery.
  If I remember correctly the laptop must be connected to the adapter sector more than 48 hours. Check in the manuals.

  Maybe is my bad English, but I do not understand second problem.
  Can you please try to explain it again? I'm sorry.

• After BIOS update numpad on my Satellite C850 does not work correctly

  My numeric keypad started to go crazy. What can I use are "0.369* - + button"home"end touches PGUP and PGDN.

  The keypad light is on and I can't turn it off. whenever I do what it s like I m by pressing the FN key and whenever I press NUMPAD 1 it always typing gibberish words when I press NUMPAD 2 he does what than done F12 key and so on for numpad 4,5,7,8

  All this happens after I updated my BIOS and has never been a spill of liquid on the keyboard.
  Any idea on this freaking problem?

  Hello

  I can't imagine that this problem could be linked to the new version of the BIOS.
  Maybe it of a simple bad luck that this keyboard problem appeared after the BIOS update.

  From my point of few, it looks like malfunctioning hardware keyboard.
  But to confirm this diagnosis, you should try workarounds.

  * 1 * workaround: first enter the BIOS and set its default value.

  * 2nd * solution: disconnect the power adapter, remove the battery, hold down power button / stop along 30 sec. Finally, reconnect the two devices.

  * 3rd * workaround: connect the external USB keyboard and test functionality.

  In case the USB keyboard would work correctly, the problem is related to the fault of the internal keyboard.

• Satellite Pro A300-15 t does not restart on the current after BIOS update

  Hello

  There is something wrong with my Satellite Pro A300-15 t. I made an update of the BIOS of toshiba recently with the latest Web site and it installed successfully. But after the installation, I noticed that my laptop does not restart when it is connected to the power adapter. It restarts and works perfectly when its power on the battery.

  After restart or start-up the laptop (on battery), it will be well when the adapter is connected.

  But, when I reboot when the adapter is connected, after his stop, just power light turns on for a second or two and gets off automatically. And not even the laptop starts manually by pressing the power button (LCD is turned off when the power light comes on for 2 seconds) when the adapter remains connected.

  So what I do is to pull the plug on the adapter, then start the computer manually by pressing the power button and reconnect the plug of the adapter to the laptop starts. It works well this way. Rest everything works perfectly.

  And this problem started after the update of the BIOS. Now, I don't know how to remedy the situation I don't know if there was a bug in the last update of the bios.

  Details of the update from: http://gulf.computers.toshiba-europe.com/innovation/download_bios.jsp?service=AE

  30/07/08
  Update the BIOS
  This Bios update adds functionality to your system.
  Satellite Pro A300 Toshiba of 3, 60 - WIN

  So please help me to solve the problem.

  Thank you best regards &,.
  Manjit M.

  Hello

  Try to update the BIOS again
  In addition, access the BIOS settings and set the default parameters. Save it and try again.

  Good bye