System stopped after bios update (Y510)

Similar Questions

• Y50 stops after bios update

  I'm pretty disappointed with the performance of this laptop. I paid a lot of money for this, and now, after the latest bios and os update it stops when you play.

  This problem only occurs when you use the version of the bios v3.03. I went down to 1.03 and it works very well. However, since I was on windows 10, there are a few problems with power management.

  What is lenovo has to say about it? Any difficulty?

  
  

• Laptop HP OMEN - 15-5010nr: Omen HP 15: backlit keyboard does not not after BIOS update

  This morning my HP omen arrived by mail, fully functional with everything in tact. After I left my laptop to install the updates from HP Support Assistant (one of these being an update of the BIOS updates), I returned to find my computer restarted and my enlightened retro keyboard does not. After trying to use HP OMEN control to fix the keyboard, I found the keyboard flashes when I click "Apply to all Zones", but then immediately turns off again. Is it possible to fix this keyboard backlit ir question can we see an update in the near future that resolves this problem?

  Found a solution! Apparently, the keyboard stops after the update of the BIOS, so to reactivate just push F5.

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• HP Envy 15 t-j100: no operating system after BIOS update

  After many failures of start-up (see messages in the forum to Boot), I was advised to update the drivers, etc. Did so, using the HP Wizard, one of the system BIOS updates. It's the last thing I did on this machine, I use now a laptop borrowed. The update of the BIOS seemed to go well, installed, then checked her restarted. But it does not re - start. "No operating system found... "Thank you very much HP.

  I told Win 7 Pro, when I ordered this machine instead of the 8 win pathetic, if I do not want to restore it to factory settings. Now, how can I get out of this hole?

  David

  Re-enter the BIOS and verify that Legacy boot is enabled-Secure boot disabled. If you need to change it don't forget to save & exit. When you restart for the first time after having turned startup security turned off, pay attention to the small notice indicating that you must confirm save this setting by entering a PIN shown + enter, otherwise these new settings in the BIOS are not saved.

• Satellite C55-A-16Z - graphics card does not work after BIOS update

  Hello

  I have a portable Satellite C55-A-16Z with windows 8 and a Nvidia geforce 740M graphics card.

  Last week he asked me to update the version of the bios at 1.30.
  The bios update was successful.

  However when I restarted my laptop I started having a BSOD dgxkrnl.sys.
  Correction of the error and restarted for an another BSOD Windows, and after the second solution, I stopped making BSOD.
  But now, I noticed its games running, if not use the dedicated card, but use the 4000 Intel.

  In the settings Nvidia dedicated card is configured to be always on.
  It seems that my card is missing, but it appears in Device Manager.
  I tried to delete, update the drivers and the default factory reset, but nothing helped.

  Also, when I go into Options power the Intel card is listed and when I disable the card intel in the Device Manager it starts to use the graphic viewer for windows.

  How can I get my Nvidia card to work again?
  Any help is appreciated.

  Thanks in advance.

  Hello

  After the BIOS update the BIOS should be set to default settings.
  You can do it in the BIOS.

  In addition, you mentioned that Windows 8 is still installed on your laptop.
  8.1 to win has already been published by Microsoft and I highly recommend that update you the system of 8 to 8.1 Win Win.

  Before you start the upgrade to 8.1 win, you should check and read the instructions step by step for Toshiba: http://www.toshiba.eu/innovation/generic/windows8_1-message/

  I guess that after the Win 8.1, nVidia graphics card upgrade works well also.

  Your comments would be greatly appreciated.

• Satellite Pro A300-15 t does not restart on the current after BIOS update

  Hello

  There is something wrong with my Satellite Pro A300-15 t. I made an update of the BIOS of toshiba recently with the latest Web site and it installed successfully. But after the installation, I noticed that my laptop does not restart when it is connected to the power adapter. It restarts and works perfectly when its power on the battery.

  After restart or start-up the laptop (on battery), it will be well when the adapter is connected.

  But, when I reboot when the adapter is connected, after his stop, just power light turns on for a second or two and gets off automatically. And not even the laptop starts manually by pressing the power button (LCD is turned off when the power light comes on for 2 seconds) when the adapter remains connected.

  So what I do is to pull the plug on the adapter, then start the computer manually by pressing the power button and reconnect the plug of the adapter to the laptop starts. It works well this way. Rest everything works perfectly.

  And this problem started after the update of the BIOS. Now, I don't know how to remedy the situation I don't know if there was a bug in the last update of the bios.

  Details of the update from: http://gulf.computers.toshiba-europe.com/innovation/download_bios.jsp?service=AE

  30/07/08
  Update the BIOS
  This Bios update adds functionality to your system.
  Satellite Pro A300 Toshiba of 3, 60 - WIN

  So please help me to solve the problem.

  Thank you best regards &,.
  Manjit M.

  Hello

  Try to update the BIOS again
  In addition, access the BIOS settings and set the default parameters. Save it and try again.

  Good bye

• HP Probook G3 450: Start slowly after bios update

  Hello everyone,

  I am a new user of laptop Hp so I need your help, I want to thank you for your time to read and help me with this problem.

  Yesterday, I updated the bios Hp SoftPaq Download Manager recommendation. Progress to succeed and the result of this action made my laptop boot really slowly. The first time, it took just 10 seconds to start windows 10 compared to more than two minutes after the update of the bios.

  I've already searched google for help, but it still does not originally.

  Please help me with your experience on it, I really appreciate all your help.

  Best wishes

  NewHpUser256

  Assuming that this PC came with the edition of Win10, all I can guess at this point is the default setting for FastStartup is in conflict with the new version of the BIOS.  It is a new form of hibernation which is supposed to speed up your boot process, but in some cases, it actually slows down.

  There are two ways to disable FastStartup Win8/10; (1) via the control panel and (2) through a command prompt high.
  
  Control Panel - open Control Panel-> Power Options.
  Select ' choose what buttons power. "
  Select "change settings that are currently unavailable".
  At the bottom of the window, under stop settings, uncheck the box about quick startup
  
  High - command prompt run the following command:
  REG ADD "HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Power" v HiberbootEnabled /T REG_dWORD 0 f d
  
  In both cases, restart Windows.

  If this doesn't fix it, there is something to play and while this PC is still under warranty, you should contact HP Customer Support directly so they put you in contact with HP Tech Support to see what they can do on the diagnosis and repair of your machine remotely.
  
  I did recently, and HP technology was able to remotely access my PC on the Internet and to make the necessary repairs.
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!
  -------------------------------------------
  However, HP customer care is generally not available on weekends, so you may have to wait until Monday to contact them.
  -------------------------------------------

  Good luck
  ========================================================================
  I'm a volunteer and I do not work for, or represent, HP.
  ---------------------------------------------------------------
  If my post helped you, please click on the Thumbs-Up symbol on my post to say thank you.
  If my posts resolved your issue please click "accept as a Solution.
  ========================================================================

• Satellite L300 - webcam does not work after BIOS update

  I've recently updated the BIOS to 2.2, and the webcam has stopped working. He disappeared, and there is an unknown device in Device Manager in USB bus controller.

  I've tried everything, even with the new Vista OS pure but nothing as there is no webcam I have installed the drivers but not recognised so I would like if I can get the BIOS to 1.5 and fix the webcam. If I can cos I need. Is this possible?
  TNX

  Hello

  I put t think its BIOS problem.
  First the unknown device (webcam) appears in the Device Manager and it means that a device has been recognized by the system and the BIOS.
  The only reason why its listed as unknown devices is: the driver is not installed correctly.

  After update BIOS, you have to put back the BIOS to default. Access BIOS by pressing F2 and in the BIOS, you can use the button to default to F9 and F10 to save the changes.

  After that you should start the machine and need to go to Device Manager.
  Mark the unknown device and delete it from the list (if possible)
  Go to control panel-> software control and check the list of software for webcam software (from chicony). Uninstall this software if its part of the list.

  Now, restart the laptop.
  Clean the operating system using CCleaner and install the correct webcam for Vista software. Note: pay attention to the 32-bit version or 64-bit.

  If the installation fails, try the Toshiba Recovery disk and define the notebook back to factory settings.

  By the way: decommissioning of BIOS is not possible because the old BIOS is not downloadable.

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Satellite A300-20 b - Touchpad does not work after BIOS update

  I've updated the BIOS on my Satellite A300-20 b latest version 2.00. Update succeeded, but when I rebooted system touchpad has stopped working.

  I tried to find the solution, resettled drivers (windows XP system). In the Windows Device Manager there is no problem with Synaptics PS/2 Port Touchpad, I see. Software Synaptics shows no problem I can enable and disable the touchpad, but it does not work for the touchpad. I tried Linux live CD and in this system does not work as good touchpad. I think there is problem in this version of the BIOS.

  Does anyone have the same problem?

  Hey Buddy,

  Have you tried to turn the touchpad on or off if you press FN + F9? Check this please!
  Also, try to load the default settings in the BIOS.

  What happens if you connect an external mouse to the laptop? It work?

  I can t imagine that the BIOS update causing this problem. If it doesn't work, you need to contact a service provider for help. They can check the touchpad and replace.

• Satellite Pro A300 - touchpad failed after BIOS update

  After that good BIOS update 2.00 to 2.10 / suggest by ALERT TEMPRO - http://support1.toshiba-tro.de/tedd-files2/0/bios-20091125132031.zip/ the touchpad of my Satellite Pro A300 - GR 1 stopped working.
  He appears under the name hidden in Device Manager. The State of the device - "this device is not present, is not working properly or is not all its drivers installed." (Code 24) "reinstall the driver has no effect of course. I can also access the BIOS utility when you start pressing F2.
  Running Vista Business 32-bit Edition.
  Ideas to solve the problem will be highly appreciated!

  Hello

  Normally, it should be possible access the BIOS, if you press F2, once you have turned on the laptop. Please check again and load the default settings there.
  And you cannot access the BIOS if you shut down the computer.

  You can use an external mouse on the laptop? Please check this too.

  I've also updated the BIOS on my Satellite A300 but I n t have a problem with the touchpad after the update.

• Satellite M100 - no speakers sound thorugh after BIOS update

  Hi all

  I have satelite M100 PSMAAA-02006 with XP. I just updated the Bios on V3.0. Speakers do not work after update but the audio jack works so with headphones I can listen to but not through Laptop speakers and the keys to media on top of keyboard play, pause, stop, next, back, etc. homepage react too much.

  Someone knows the solution to this issue. Or is it possible to get the old BIOS? Although I not sure aboutt previous version.

  need quick help. Please answer as soon as possible.

  Thanks & best regards...

  Hi Julie,.

  I doubt that this was due the update of the BIOS. Is that what you have loaded default settings after updating the BIOS?
  Have you chosen the correct BIOS update?

  Normally you can hear the sound on the speakers laptop if you disconnect the headset. Make sure that the sound is not muted, you can do this with the FN + ESC key combination.

  About the multimedia keys, I would recommend reinstallation of Toshiba common Modules. You can find it on the Toshiba site.

• Re: Satellite - blue screen after BIOS update

  Hello

  My computer laptop girls worked very well until I did the BIOS update this morning. Now, I get the blue screen of death STOP: 0X0000007F. Help, please

  concerning

  Carol

  Hey, Carol, welcome to the forum! :)

  Don t misunderstand me, but may I ask why you n t post more information about your problem?
  Important to know is that your laptop you have exactly and where to download the updated BIOS and for what model. This is important information.

  By the way: have you ever tried to load the default settings in the BIOS after update?