Y510p and Smart Response Technology - cannot be enabled

Similar Questions

• XPS 8700 - Windows 8 w / Intel Smart Response Technology re - install

  Hello community,

  My hard drive in my XPS 8700 failed recently. I got a replacement and have installed the new drive in the chassis. It's the only drive (2 TB), but I also (30 GB) SSDS for Intel Smart Response Technology.

  I have a problem with the OS / Intel Smart Response technology Setup. I'm trying to (re) install Windows 8 of the disc. When I run the installation of the OS, just after choosing language preferences a screen will appear indicating that a media driver is missing.
  "Load driver".
  A media computer driver needs is missing. It could be a driver DVD, USB or HDD. If you have a CD, DVD or a USB flash drive with the driver on this subject, please insert it now.
  Note: If the installation media for Windows is in the DVD or on a USB drive, you can remove it safely for this step. »
  I guess it's regarding the pilot of SORTS. I tried to put the pilot SORTS on a USB but it is not detected when browsing.
  "Load driver".
  No pilot of the plane have been found. Make sure that the installation media contains drivers and then click OK. »
  I need help ensuring the RAID and BIOS are correct before installing Windows 8 with TRIE. Currently, neither the SSD or HARD disk created a RAID Volume (note No changes have been made in the BIOS, but the existing RAID configuration has been removed from the SSD).
  Emergency assistance would be greatly appreciated.
  Dell XPS 8700
  Windows 8, 64-bit, English
  2 TB hard drive 7200 RPM SATA + Intel SRT (30 GB Lite-On SSD MSATA)
  24GB Dual Channel DDR3 1600 MHz - 4 DIMMs

  In collaboration with a Dell technician by CAT, we have identified the problem with the driver files SORTED on the USB. I tried to download from the driver and Utilities disc that came with the computer, however the correct files are not extracted from the USB.

  The tech located the driver appropriate and after extract the USB driver has been detected.

• Problem starting Windows 8 (associated with quick start + Intel Smart Response Technology SSD cache)

  Hello
  I have a problem with the fast start-up of Windows 8. When I shut down my PC everything works fine, but when I turn on the PC, Windows will load until a certain point and then suddenly start screen appears again. The second departure is always successful.

  I discovered, when I turn off the Quick start, the computer starts without error on the first attempt. It goes the same for when I disable Intel Smart Response Technology (SSD cache). There are no problems when I use Hibernate mode.

  Recently I did a BIOS update, so I don't know if there is a setting in the BIOS that is may cause this error?

  Thanks in advance for any help!
  Martin

  Hi Martin,

  Glad to know you solved the problem. Thanks for sharing of the resolution, because it would help the other members of the community to the same question.

  Please do not hesitate to answer, in case if you need help or information on this issue.

• Windows 7 in a VM can use the Intel Smart Response Technology?

  I want to run Win 7 in a VM under Xen. Is it possible to make use of the Intel Smart Response Technology with Win 7 in a VM?

  Hello Ivan,.

  Welcome to the Microsoft Community Forum.

  The Microsoft Answers community focuses on the context of use. Please reach out to the business community of COMPUTING in the TechNet forum below:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

• Smart response caching: HARD + SSD on Inspiron 15R drive SE, mSATA value SRT, still no button "Accelerate."

  Hello

  This is probably a common problem that has been explained earlier, but I cannot find an answer here-I found describing almost the same question, but still not the same as the son.

  So I have a cool Inspiron 15R SE with pre-installed Windows 8, 1 to HDD and SSD 32 GB on mSATA included for caching purposes. The problem is that, as far as I can see, without acceleration/cache that really happens with my SSD as just another drive.

  In the BIOS my mSATA operation is set to 'Intel Smart Response technology' which seems to be a good option for caching. Looks like on this screenshot I took from another thread, the yellow highlighted option is selected in my system:

  

  But when I boot in Windows 8 and run the Intel Rapid Storage Technology technology, I don't see "Accélération" button / tab - as if my drive is not eligible or is in the wrong mode. This is the screenshot of my Intel utility for you to see there is no option to activate the cache:

  

  If it's relevant, my SSD drive appears in my disk management console and is also available as a regular drive in Explorer and other files with a drive letter assigned managers (guess which indicates the acceleration is not in use).

  There is also a Hibernate (8 GB) on this disk partition, but there is still enough for caching (mandatory min 16 GB, 20 GB left) free space. Should I try to disable hibernation? My hiberfil.sys file is on the HARD drive so that probably won't help. Here is a screenshot of another utility pre-installed from Intel, Intel Quick Start Technology Manager, if this might be relevant:

  

  Any ideas are much appreciated, I've been strongly trying this additional disc and it was actually the main reason for me to choose this particular laptop model. It's a shame, I can't use it for some reason any.

  Thank you very much!

  I found the answer. To activate the acceleration must be no. PARTITIONS on the SSD drive even if it is still not enough allocated space.

  If the partition of QuickStart technology, with that my laptop came prevented Rapid Storage to accelerate.

  After I deleted all partitions on the disk, it worked.

  If you still need the partition of quick start or for other purposes, you can specify less space for acceleration during the installation and create your partition later.

• How do I configure Intel Smart Response on my hybrid drive

  I have a laptop HP Pavilion dv6t-7000 CTO. I have a 1 TB HDD with a SSD of 32 GB used for caching and acceleration using Intel Smart Response Technology and Rapid Storage Technology console. I had to send in my computer for warranty service which included the replacement of the hard disk. I figure that the SSD is not configured.  Below I have screenshots of the screen that displays now after the POST (which did not appear until I sent it to the service) and the console Intel RST.

  Just trying to get back to its original settings, where it uses Intel Smart Response Technology to improve performance.  How can I configure the SSD account given what shows in the screenshots below?

  (You may have to right-click on the image and open it in a new tab to see it enlarged.)

  Since she came back, I get the following after the POST screen.  I am limited to the 3 options (reset on a drive non-RAID) and 6 (output):

  

  Technology Intel Rapid Storage Technology console:

  

  

  

  It's corrected now. To fix it, I did a complete backup of my files and settings, and then, in the window of the acceleration, I clicked on separate. I've also given to SSD available. After restarting a couple of times, everything seems normal.

• SW2 - host App and Smart Connect different certificates. Host application cannot start.

  I had my 2 SmartWatch today and installed app Connect Smart and SmartWatch 2 since google play, got the smartwatch of pairing with my bluetooth phone manual connect.

  But in the notification bar I get "the application host and Smart Connect different certificates. Host App cannot start. "and I can't go settings on Smart Connect to the SW2.

  Please help, now I can't use the no apps smartwatch becouse...

  It's very strange, these files works fine for me in an S3.

  Would it be possible for you to make a backup of your phone then reset (or reinstall the software using Kies if possible), and then try again (before restoring the backup)?

• I created a my page book epub file, and it works perfectly in ibooks. But it does not appear on my other devices, and the .epub file cannot be successfully sent by e-mail. 5.6.2, iBook 1.5 pages

  I created a my page book epub file, and it works perfectly in iBooks. But it does not appear on my other devices, and the .epub file cannot be successfully sent by e-mail. 5.6.2, iBook 1.5 pages

  What's not?

  You must check the iBooks category in your OS X system preferences: Panel iCloud: iCloud Drive: Options: Documents Panel. On iOS, you must have enabled to iCloud and in the iCloud Drive location setting iBooks. Also, in iOS parameters: iTunes and App Store, ensure that iBooks is running.

  The iBook.epub file is a compressed/compressed and renamed folder that represents a single file to any email client. What do you mean, it cannot be sent correctly - and it's your experience, send, or the failure of the recipient to view the ePub document? What email client?

• many runtime errors and slow responses

  Originla title: what is WiseFixer and is a legitimate program?

  I get a lot of errors of execution and slow responses.  Ran the scan in the wise Fixer but was reluctant to unlock the registry to run the repair.

  Hello

  · When you receive the errors?

  · It is when you work with a program or a particular application?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed on the computer?

  · Give us the exact error message that you receive to help us best solve the problems.

  For the problem with the performance of the computer, you can follow the steps in the link below: how to make a computer faster: 6 ways to speed up your PC: http://www.microsoft.com/atwork/maintenance/speed.aspx

  NOTE: Microsoft cannot guarantee that problems resulting from the use of third-party software can be resolved. Software using third party is at your own risk.

• I reinstalled the operating system on the same computer multiple times, however, this time it is said, I'm 'cannot be enabled.

  I have problems activating windows x 64 bits.

  I reinstalled the operating system on the same computer multiple times, however, this time it is said, I'm 'cannot be enabled. Recently, I updated my motherboard and changed to a quad core. I would appreciate help from the administrator. Legitimately, I bought my version of Vista x 64 tiger direct for years and relied on it as my OS for a while now. Any live medium or other assistance, advice, etc., would be appreciated. This operating system has been reinstalled several times, and the last time I had to reinstall it is because I closed windows because he wasn't updated correctly, and then restarting the operating system has not yet worked so I HAD to reinstall. Now windows says that my code is already used. I'm ready to take pictures, show my keycode and do anything to get my system online. Vista is saying I need to activate within 3 days. Also, I have problems installing Service Pack 1. Which maybe has something to do with my questions? Please, someone help me!

  Mark,

  In this case, you will need to contact Microsoft by phone for your landline number. Usually, most product keys have some time, they can be turned on before you reach this State.

  Best,

• ICS 765 error code: Internet connection sharing cannot be enabled.

  Well, I get this message every time I try to share my internet through like an Ad - Hoc or anything else at all. "Cannot enable shared access.  Error 765 ICS cannot be enabled. A LAN connection is already configured with the IP address that is required for automatic IP addressing. Sense, I can't do it like my xbox live or anything. Oh, I use an our phone company wireless internet card and it is installed on the same laptop to my father, and share us through an ad hoc when he uses it, that would be the problem?

  Thanks for any help!

  -Buki

  Copied from Richard to Yahoo answers. It worked for me.

  "ICS in Windows assigns always 192.168.0.1 to the network adapter that is used to connect other devices to customer that you want to share the Internet connection. For example, if you have an Ethernet cable from your computer to the Internet (for the modem or router) and a WiFi adapter that will provide a wireless network for other devices to connect to, then the WiFi adapter will be given the address 192.168.0.1.

  However, if any other adapter (or adapters if there are more than two network interfaces on the computer) using the 192.168.0.0 subnet, then sharing does not work correctly because you will have two adapters will try to use the same subnet.

  The most likely cause is that you have a router between your computer and the Internet, and the router is configured to use the 192.168.0.0 subnet. If this is the case, log into the router and change its subnet. For example, if the router is set to 192.168.0.1 as its address, change it to 192.168.1.1. Restart the router and the computer.

  If you had set up a static address on your computer for the Internet connection, you will need to make a change similar to the addresses of the computer (IP address, gateway address, and DNS address). If your computer uses DHCP to obtain its address, then it updates automatically when you restart the computer. »

  Good luck.

  I just changed my routers ranging from 192.168.0.1 to 192.168.1.1 subnet and sharing works fine now.

• How can I find the question that I dropped off the 9.11.13 and the response that I received on my hotmail to Kim?

  Hello

  I guess that everything that you people are as stupid as me, so I need help.

  Saturday, I tabled a question about Live Mail, do not sync with my 2 Hotmail accounts.  I received a reply from Kim through my email account, and after following that advice should meet him which I did by hitting his email response.  Now, I get an email saying that my answer was available.  So I thought that maybe if I found my question, his answer would be to this topic, in the "community" section where I placed my initial question and I could hit answer here.  There is no section for Windows Live Mail in the Community Forum if I select Windows 7 Email and communications as my topic, as it was the closest I could get.  How I'd like a tab or a box that says "see your question and the responses, it has generated."

  I know it's a stupid question, but when you get past 70 things aren't as obvious apparently.

  Can someone help me?

  Alison

  You cannot respond to a notification by e-mail. Return to the forums and click the name Alison n (2) at the top of any page of your profile and look at My Questions to find the wire.

• In Win 7 I get an error for various leave and- or "this action cannot be completed because the folder or the file is open in another program."

  I'm money than Win 7 Home Premium 64-bit SP1. The following information are linked to the steps to solve a persistent problem. Please read carefully and answer completely, since you asked users to report carefully on the long process of troubleshooting-advice you provided. I've been at it for six hours now in this round of troubleshooting.

  I tried to solve the continued permission errors and- or "this action cannot be completed because the folder or the file is open in another program."  This happens when attempts to cut-copy-paste------delete files (including the specific details listed below).  I searched on the Microsoft Support site to find answers to solve the problem, including the thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-files/in-Windows-7-getting-error-the-action-cant-be/449b2e05-8ED0-4A72-98bd-dde430d27e10?TM=1356626412321

  In accordance with this notice of sons, I emptied my Temp folder. The problem persisted. I downloaded the app 'Take Ownership' and also tried with periodic and sporadic success. It seemed to lengthen the time between recurrences of the problem - that it would allow me a half a dozen of all cutting------copy-paste and------or remove actions, until the error messages stop me to exercise that or any other action.  Then, I used the task Mgr end explorer.exe and reopen it to see if that makes a difference. For a while it worked, where I could make a few cut sporadically------copy-paste and------or delete actions. Today I'm at the point where I can preform one action, then I have to open task Mgr, end explorer.exe and then restart it to perform again a more cut-copy-paste or delete action. So, I have to return to the task Mgr and repeat the process above, for each new action I want to perform.

  I watched rained down in the above quoted thread, and followed Support Engineer Samhrutha G troubleshooting tips - method 4 - start the computer start-up in minimal mode and to use the diagnostic selective startup. In previous discussions, you have asked for advice as to what you were doing when the problem occurs, so I rated as below:

  I went into msconfig, unchecked "Load Startup items", went to the tab Serivce and allowed only half of them. He was 12 of 24 listed entries. During the tests, programs that are only open on my desk were two windows explore and Notepad to save the results. I got the following results:

  I moved the contents of a folder on my main C drive on my external drive of 3 TB. When I then tried to remove this folder on my external hard drive I got the message

  "You must be authorized to perform this action."

  You need authorization S-1-5-21-602162358-602609370-839522115-1004 to make changes to this file.

  After I clicked retry the record has been deleted. When I went to delete another folder in the same location on my external hard drive, he deleted the first time. He was then three other orders normally external hard disk.

  Then I tried to delete a file in a different location on the external hard drive and the message

  "You need give permission to delete this folder.

  When I clicked on continue what he deleted

  I cut and pasted a file from my external hard drive to my C drive. The record stuck on drive C. He pasted the folder on drive C, but the original folder remained on the external hard drive, even though it was a cut and paste. So when I went to delete the original folder that should have been cut, this message came:

  "You need permission to delete this folder.

  When I clicked on continue he grew up:

  ", You need permission to perform this action."

  You need authorization MYCOMPUTERNAME\MYCOMPUTERNAME to make changes to this file.

  When I clicked Try Again he deleted. But why he would leave the original behind if it was a cut and paste?

  After that, I tried to cut and paste a file to a location on the external external hard drive to another location on the hard drive, after I had seen the contents of that folder and went up a level to the folder parent to try the cut and paste. I received the following message:

  "Cannot perform this action because the folder or the file is open in another program

  Close the folder or file, and then try again.

  When I clicked Try Again it just repeat the error message, don't not allowing me to carry out the action and any other further reduction-copy paste and- or delete actions. I had not opened or closed all other folders, windows or applications, during the above test.

  Based on the Support Engineer Samhrutha G troubleshooting tips 4 method found on the following thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-files/in-Windows-7-getting-error-the-action-cant-be/449b2e05-8ED0-4A72-98bd-dde430d27e10?TM=1356626412321

  (same thread as cited previously) Then I went into msconfig > Services and reduced the number of items in the selective startup of a unit, as I started 11 - instead of 12 - 24 listed entries. Upon reboot, I decided to re - check msconfig. In msconfig > Services he showed 165 points. All had a check in the box next to them. These 165 points, 56 showed as "ongoing" the rest showed as stopped. It would be useful that I specifically what were these 56 entries?

  I continued with the troubleshooting test based on these settings initiated by Support Engineer Samhrutha G tips to reduce the selective startup (remember... it was 11 selected items)

  I started by I try to copy / paste a file from my external hard drive to my C drive. He has successfully completed. When I went back to the location of the original file on the hard disk external and clicked on undo move, the message came:

  "You need give the administrator permission to move this folder.

  When I clicked on continue as he moved the folder

  Then I tried to cut a file on the C drive and stick it in my external hard drive. He successfully completed the task. I then went back to the original location of the file on the C drive and tried to "Undo Move". I received the following message:

  "You need give the administrator permission to move this folder.

  By clicking on continue he grew up

  "You must be authorized to perform this action."

  By clicking on try again, just to repeat the error message and could not undo the move

  I tried to cut the entire contents of a folder on my C drive and stick it in a directory on my external hard drive. He was able to make the cut and paste but left a folder and two files back in the original location on my C drive. When I then went to cut the 3 elements he missed and move them to the location I had initially indicated on my external hard drive - for the first file he brought up in the dialogue that he was already stuck and I would like to merge, etc, that I clicked on none. the second file in the sequence that he grew up:

  "You must be authorized to perform this action."

  When I clicked on continue he grew up

  "You must be authorized to perform this action."

  You need permission from the administrator of the computer to make changes to this file.

  When I clicked on Try Again, he said.

  "Cannot find this article.

  It is no longer in C:\Projects\FolderName. Check the location of the item, and then try again.

  When I clicked Try Again he repeats just this same error message until I had to click Cancel to exit.

  The record was then only showed only two remaining elements. Because the first cut and paste involved 22 files and 3 folders, now I am unable to say which of them got ignored or lost. When I updated the location of the original files he showed that a single folder on the left and the content was empty. When I checked it now duplicated and pasted to the location of this folder on the external drive, he was there with the appropriate content. So he had left this file to the original location, but it was empty. Why this erratic behavior?

  When I went, then, remove this folder remaining from the original location, he deleted successfully. If you understand the above message, you notice that a file has disappeared.

  I now need to mention an incident b4 I started the process of solving problems today. I felt that you needed some context b4 I mention this. I had tried to cut a folder that contains 33 files and 6 records. The six files contained two subfolders whose combined total content contained 28 photos - a mixture of mp4, JPEG and mp3 - for a total of 61 files in the parent folder, I tried to cut and paste. I tried to paste the folder parent on my external hard drive. He started at the cut and paste normally 7.04 GB and towards the end, I got the message

  "Cannot perform this action because the folder or the file is open in another program

  Close the folder or file, and then try again.

  He was unable to finish when I clicked on Try Again, and I had to cancel out. However, he had removed all but one of the folders containing three files and it was not pasted into the new location. They were gone. I did a search on Win for some of the names of known files in this folder, and none appeared. Fortunately I had them on a second external drive. I plugged it to restore files, and of course that means more open task Mgr, ending explorer.exe and reopen in order to restore the files that explore had lost.

  After my results displayed above two rounds of by using a clean boot and selective startup, you can see that it is very difficult to actually diagnose the problem because it happens inconsistently. It is also very time consuming and very, very, very, very, very frustrating.

  I decided to try the method of disabling "just" thumb caching in the registry according to the advice of Robert P in the thread quotes. He said that I should go to Start > Run > gpedit.msc and "disable implementing caching thumbnails in hidden thumbs.db files" that was published of course in OK Win 7 > files, folders, and storage of the Microsoft Community forum. So I typed gpedit.msc in the search bar, and there was no instance of gpedit.msc, only setup.exe, I had to take was to gpedit.msc.  I installed it and after installation I typed again and he has not yet posted. So I rebooted. Restarted it showed up. When I went to run gpedit.msc, he brought to the top of the window with the error message group policy "MMC could not create the snap" when I looked up this article in the Microsoft Community, I found the link to the Win 7 forum, where the Star NIthyananda reported community
  "Gpedit.msc is not available in Windows 7 Home premium.  Discussion here:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/when-i-open-gpeditmsc-on-my-computer-which-is/b1576a0f-348a-49D8-be70-d83d0f36e8aa?tab=AllReplies#tabs

  He then mentioned

  "If you want to disable caching of thumbnails, you can access the registry editor and go to changing the location according to the value [note: its mine incorrect grammatical syntax and not]".

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced\DisableThumbnailCache ".

  with no information on how actually access HKEY_CURRENT_USER

  I found the appropriate information on how to access the registry in Win 7 running regedit, with information on how to navigate to the appropriate location in the registry to disable the thumbnail cache

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced\DisableThumbnailCache

  but there is no entry "DisableThumbnailCache.

  I researched and found that you can add it in

  http://www.SevenForums.com/tutorials/10794-thumbnail-cache-enable-disable.html

  I downloaded the Disable_Thumbnail_Cache.reg file. After running Disable_Thumbnail_Cache.reg to merge it into the registry, I then returned to HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced\

  and yet, there was no entry on DisableThumbnailCache

  The second method mentioned in

  http://www.SevenForums.com/tutorials/10794-thumbnail-cache-enable-disable.html

  has been to access via the Group Policy Editor

  I searched for the Group Policy Editor in Windows 7 search bar and it showed three entries

  A folder titled "for Windows 7 Group Policy Editor.

  a zip file named "add_gpedit_msc_by_jwils876_d3kh6vm.zip".

  Setup.exe

  The "Group policy for Windows 7 Editor" folder contained just the same two files listed below it

  So, I went ahead and ran the setup.exe and then restarted. After the reboot, I did a new search for the Group Policy Editor and he grew up just three results.

  I went back on the WindowsSeven Forum and found advice in the thread

  http://www.SevenForums.com/tutorials/3652-local-Group-Policy-Editor-open.html

  Title: how to open the local Group Policy Editor in Windows 7

  The tips were:

  To search for a group policy or the registry key, value, etc., see:

  Political research group

  The link above leads to:

  "The GPS is going to move to a new end area January!

  http://gpsearch.azurewebsites.NET
  You will be redirected in 15 seconds! »

  I waited about 3 minutes and it went nowhere, so I clicked on the http link and he grew up:

  GetCategoryDependencies() - 500ServerError

  This is where I could and I am now. And I can't "simply" disable caching of thumbnails. Can I return to my workspace and all simply continue with the editing work that I do, which is to cut, or -copy-paste and or delete files that I advance in my workflow. I can't do it without opening task and then Bishop ending and re-open explorer.exe for each order, I want to achieve.

  At this point now a few hours later including writing this message, I think that a new facility would be easier, more rapid and less headaches but that will solve the problem?

  Sense my frustration?  If this is not the case, let me make it clear. It's extremely frustrating. Why Windows doesn't have a fix for this is an error permanently?

  It was mentioned in the original thread that I cited that it would be better to start a new thread and continue to add my comment to the answers already posted 138. This problem has plagued me for months. Please notify

  As you have tried many fixes and changes to the registry, I suspect that your only option is a clean installation

  And having done so don't try not to cut/copy anything other than the data in the files in libraries in any other player. Copy of records of the victory Road will result in the registry locations becoming screwed.

  And if you really need locate the lbraries on another drive will redirect the location of other libraries that animate

• I'm totally confused about records, collections and smart collections.

  I am a complete newbie to Lr so please forgive what are fundamental questions without doubt!

  In records, I have 2 folders - Annecy and Aix which have different vacation photos.

  In Collections, under smart Collections, I have a folder named Aix which has my pictures of Aix and that is synchronized to Lr on my ipad.  However, although Annecy is listed under Collections, it is in a folder at the top of a new tree under smart Collections but does not part of smart Collections.  I hope that makes sense!  This issue of Annecy does contain pictures, and the only thing being synchronized on ipad is the name of the folder.  How can I copy photos from the folder in the folders in the Collections folder?

  I read that peaks must be in the Collections before they can be synchronized.  However, on the ipad there is that a folder named "Pictures Lightroom" it contains 242, the same as "all photographs synchronized" under the heading catalog when Lr appears on my desktop.  At present, I am initially upload my pictures in my office and then import to the RL.

  Finally, about mobile Lr in response to a previous johnreliis investigation informed that I must ensure that I am connected to creative cloud on the ipad before being able to view synchronized + photos on the ipad.  I downloaded Lr mobile on the Apple store and have nothing to CC on the ipad.  Now, I wonder if the reason that the pictures of Annecy are not displayed on the ipad is due to the fact that, at the present time, they are not in a Collection.

  Thanks in advance for all you can give me advice.

  Richard

  Just drag Annecy out of smart Collections and next to Aix.

  What is called "smart Collections" is actually a Collection Set - that is a container for other regular or silent collections (like your Aix) and smart collections which include images of criteria that you define. Notice how "Smart Collections of" has a different icon from the smart collections inside, looking more like a box. So what you could do then is to create a set of Collection called France and drag Annecy and Aix in it.

  To get the pictures in the Annecy collection, you can find them in your folders and drag the thumbnails in the grid and place in Annecy.

• When I started to update my iphone to ios 10 and watch 3.0, cannot already display the pictures of my watch. Logo of loading only. And he thinks it will take a hayss of 1000 years. Help, please

  When I started to update my iphone to ios 10 and watch 3.0, cannot already display the pictures of my watch. Logo of loading only. And he thinks it will take a hayss of 1000 years. Help, please

  Hello

  If the software on your watch is being updated, leave your watch and your iPhone until the process is complete (including the not remove your watch on the charger):

  Update the software on your Apple Watch - Apple Support