Cisco Network

Hello I just build a lab at home. In my current lab, I have 2 SW and 3 the router. I have a problem, I do not know what Miss me in my config. My router cannot ping my SW. and I also want to change my LAN from VLAN 1 interface connection at 30 of VLAN

Hello . . Want to confirm about version 3 of DRIFT and interoperability VTP version 2, if the VLANs created in a switch running vtp version 3 will be dynamically learned by a switch running vtp version 2? . . I'm trying lab these: .. SW1 = acting as

Hi all I noticed that I have a communication between sites when I had configured the default gateway in the PC which is not in the same segment, as is their IP address. As far as I know, whenever the intended traffic is on a different network, its si

Hi friends, Can someone suggest me a script to do the backup of the devices(routers/switches) network. As the running configuration with only once for all devices. Thank you Mohammad.

Hello guys,. --- I try to follow separately 2 switches in a stack of 2-switch and unfortunately not able to find the corresponding temp OID of the STACKWISE-MIB/STACK-MIB/ENVMON-MIB. None of these mibs compelled the info of the temperature. STACKWISE

If I create an ACL on a Cisco router and apply it to an interface, then I change the ACL again must I apply again to the interface? It is already applied so I'm not sure. Also have I not always do the "all permit" after I added a rule in the ACL beca

I am quite new to the thing whole cisco here.  I'm very hesitant to make changes as I am not sure that I take down the entire network of 200%. (We are a very small company) We have a router cisco 1811 (yes I know its old) We now have a road map and I

I make a practice of the "CCNA Exploration 4.0: access the WAN student Packet Tracer manual" (activity PT 2.1.7: Troubleshooting a Serial Interface). I did the topology according to the image and set IP addresses on the correct interfaces. Almost, I

Hi guys. I'm trying to configure a router for my client. It's a 2911 3 interfaces Gig with 1 x EHWIC 1GE(RJ45/SFP) I have a firewall integrated across the beam of k9 security. I have a static IP network set. and the old network looks like this. WAN->

Can we find if a stream is using tcp or udp by using the command 'sh ip cache flow? indicate here 06 and 11? Routert #sh ip cache flow Vl52 TE3/4 10.2.1.1 1.1.1.1 06 48 0017 8389 Vl59 192.168.1.1 Te3/4 10.2.2.2 11 b 007 007 b 0

Anyone know this command is? how it will be useful for my server?

I seem to have a problem getting a 3xT1 stuck solution to work. I can get 2 out of the 3 T1s to come and pass traffic, but I can't the third party to be added to the solution. Material: No. 2851 IOS: c2800nm-advipservicesk9 - mz.124 - 15.T8.bin Modul

I'll set up a laboratory to start on my CCNA and I have two s and two 3640 2620 s. I want to upgrade all units until I started on the CCNA and I'm unable to work on what the final version rommon is for each of the routers. My 3640's are on the versio

Hi - I think about some applications of unified communications to third parties under VMWare ESXi5 running on a Cisco SRE 900 module.   According to the docs Cisco, 3rd party apps are supported on these modules (see table below), but the app in quest

Hi, I tried to find if it is possible to add the ability for static routes to DHCP clients on the Cisco IOS DHCP configuration mode. I'm looking to add a parameters as defined in RFC 3442, like this one, located on the ISC DHCPd server: Global settin

Hello, I have these types of errors on a 2611XM router. Anyone got a clue? tell xak #sh connect Syslog logging: activated (0 messages dropped, rate limited, 2 messages vacuum of 0, 0 overruns, xml disabled, filtering of persons with reduced mobility)

Hello dear! I have the following topology: Cisco 3845 gi0/0 - switch Foundry - fa0/0 Cisco 7206VXR CISCO 3845 *. interface GigabitEthernet0/0IP 192.168.80.90 255.255.255.128no ip proxy-arpIP accounting output-packetsfull duplexSpeed 100media type rj4

Hello Is it possible to run QPM 4.1 on a virtual server Windows 2003? ThanX

Hello Recently, I joined ACS 4.1 with LMS 2.6 follow this document: http://www.Cisco.com/en/us/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/prod_white_paper0900aecd80613f62.html The integration has been a partial success, because after the integrati

Backups on my LMS server fails with a message that makes no sense to me: / cygdrive/d/CSCOpx/bin/tar: /CSCOpx/campus/etc/cwsi/DeviceDiscovery.properties: cannot stat: no such file or directory / cygdrive/d/CSCOpx/bin/tar: /CSCOpx/campus/etc/cwsi/ANIS