Cisco Network
serial interface T1 routers back-to-back 1841
Hello everyone, I'm trying to set up my CCNA lab environment and I everything works fine, including crossover between my three 1841 routers connections (all interfaces are on the rise, and line protocols are all) With regard to connections, through c
About iBGP Peering
Nice day Can someone here help me please about iBGP peering because I do not have a full mesh between all peers, some courses are not advertised to other peers. The roads from the Dominican Republic are not announced to wan routers basis nor the seco
Group of channels on 2 switches
I have 2 24-port Catalyst 3560 switches (call them, one switch and switch-b). They are connected together by a cable connection and not stacked (the c3750 is stackable but not the c3560). Is it possible to have a group of ports-channels with 2 ports
Remove the port from the channel-group
I met a strange problem with port aggregation, where I decided to remove a port of a port channel and put it in another, but in my SNMP tool, it still belongs to the old channel of port and the new at the same time. Port channel was created using: (c
which switch to a 16 floor building
Hi guys. I am designing a network for a 16 floor building. The network will include about 400 IP cameras - all POE or UPOE from a central location. Everything is going to be multicast. My questions are: What should be used? I was thinking about 37
Router cannot ping off the grid
The situation: Router (ip 192.168.16.1) is the default gateway for the whole of the company Anyone in the company is able to go on the internet and ping 8.8.8.8 (google DNS) of the PC it is I have myself my laptop have IP 192.168.16.170 and I can pin
Clear counters
Hello Does anyone know what is the command which will ONLY erase my E1 counters? Its a router 3800 series. I think the command is "clear counters series" then I get home 4/0/1, but it says command is not recognized. E1 4/0/1 is down. Applique type is
ASA5505 problem of asymmetric routing? (I think)
Good evening everyone, I'm looking for suggestions for a solutoion I met today... I am installing a new router and firewall into an existing network. The router is an Edgewater VOIP router to a cable connection with static IP. The firewall is an ASA5
First 2.0 - Urgent - discovered topology
Hi team, Can you please guide me to discover the topology on Cisco first 2.0, so that we can see the first Cisco topology. Thank you.
Enable the STM-1 on a CISCO7606-S SPA-1XOC3-ATM-V2
Hi everyone I need your help on this, I have this problem, I need to activate the STM-1 on this Submodule: 1xOC3 ATM SPA, more specific: MOD Ports card Type model serial No. 2 0 4 - subslot SPA Interface processor-400 7600 - SIP - 400 SAL1706YTSW Sub
map of Cisco network topology first Infrastructure
Hi just want to ask if it is possible to create a map of the network topology of edge of the main cisco which shows the cable devices and wireless infrastructure, or do we need another cisco product to accomplish. Thank you
A way to allow others to view saved in topology?
Hello Is it possible within the topology Services (LMS 4.2.3 with 5000 devices) to allow other users to see topology configurations. We take care of a large number of sites and I have created groups defined by the user for each site. Within the ser
Start the LMS 4.2.3 SNMPv3 + tracking users
The user tracking is able to operate without SNMPv2? Recently, I've implemented SNMPv3 on a couple of Cisco 3750 for test the LMS functionality. Given that I removed these switches SNMPv2, I no longer get the IP and MAC address information in user
Inaccessible Endhost
Hi all after reconfiguring my 4.1 snmp v2 SNMP v3 the endhost LMS are not accessible anymore. Before you configure snmp v3 I have purged the database endhost to repopulate it. After tasks are performed without endhost can be added to the repository.
User name is not filled are in the table of user tracking.
Hi all I use LMS 4.2 I activated the user tracking and I get the ip address, MAC address, host name in the table of user tracking. But enter username in the user tracking is not be filled. I even enabled get the username by guests in the areas of hos
When to use the filter VLAN vs SVI-list of access on the switches?
If VLAN 10 is a user of 10.10.10.0/24 subnet, VLAN and I want torestrict which servers can access these users in VLAN 10, I can configure an access list and apply the ACL of a VIRTUAL local network access plan or apply the ACL on the SVI "interface v
IOS K9 catalist 4507R + question E
Hi all We have a 4507R Core4507 #sh inv NAME: 'switch system', DESCR: "" Cisco Systems, Inc. WS-switch 7 slot C4507R + E ". PID: WS-C4507R + E, VID: V02, SN: FOX1543HEHT Clock NAME: 'Module', DESCR: "clock Module. PID: WS-X4K-CLOCK-E, VID: V01, SN: N
Activation of port security on C4507R stop port
I'm trying to enable port security on of several 4507R. When I try to set up a range of ports on the switch will randomly 1 or 2 in err - disable. It's different every time I have applied the config to the same port group. However if I do them one
Using the "character in a be executed the command (EMM)
Hello I ran against a little challenge construction of a function on a menu based EMM. I would like to have a user to change the number dialed in a chat script, but the script of cat command uses the character "in his order. The same character "is al
C2960-lanbasek9 - tar.122 - 35.SE.tar in CW RME import problems
Dear all, When you try to import the IOS c2960-lanbasek9 - tar.122 - 35.SE.tar in the repository of the Cisco Works LMS RME software I get the following error: SWIM0009: Unable to retrieve the attributes of the image. Check if it is supported by the