Cisco Network

Hi all Huawei switches have a simple option to generate several VLANs (especially useful when you want to trunk VLANS through the switch). All do you is enter "vlan batch 2-4000 ' and VLAN 2 to 4000 will be created. Cisco has a version of it for thei

General question about BGP. Taking this config: 1.1.1.1 neighbor prefix-list MY_PREFIX_LIST in 1.1.1.1 neighbor MY_ROUTE_MAP route map in MY_ROUTE_MAP allowed 10 route map the local 110 AC value IP-list of prefixes MY_PREFIX_LIST seq 5 deny 2.2.2.2/3

Hi, I'm not able to activate the effect (manual CTS) on the WS - X 6716-10GE module. I have a VSS with VS-SUP2T - 10G installed. I am able to activate the effect (manual CTS) on the WS - X 6908 module - 10 G. Effect is supported on the WS - X 6716-10

Hello I just set up our first server of Microsoft using multicast NLB cluster. The entry door of the VLAN is a 5540 Cisco and servers are connected on a pile of Cisco 3750. In order to let the ASA before executives for this multicast group I put stat

We have a POS 155 Mbps circuit. There are tail drops that occur on the default class that is allocated 25% (38,75 Mbps). There is a part of the voice traffic, but it is the priority in queue and is not a problem. Other control classes also OK. But wh

Hello I'm implementing an IPv6 tunnel. I use IOS Version 15.2 (4) M4 on a router Cisco 881. I've set up 3 different IPv6 networks: Here is the configuration of my router R1: IPv6 unicast routing door-key crypto keyring1 pre-shared key ipv6 2001:DB8:1

Hi all I'm having some trouble getting the ACL work they way I want. I have a lot of clients in differnet VLAN (vlan 6-10) and my ASA (10.1.99.254) on vlan 99 for internet access. I need VLAN 6-10, to have access to the ASA for internet, but VLAN 6-1

Hello I have following cisco catalyst and OSPF running switches. 3750G (C3750-ADVIPSERVICESK 12.2 (25) SED1) 3750 X (C3750E-UNIVERSALK9-M 15.0 (1) SE3) 3850 (cat3k_caa-universalk9 03.02.01.SE) They are all connected through the WAN L2 (192.168.40.x/2

Hello world I wanted to deploy a configuration model 'first infrastructure 2.0. I tried with the output of the model "banner Configuration-IOS" box. I have deployed it to a device that is a switch to Cisco Catalyst 2960 - 24PC - L. I chose "Add" in t

Recently, I have configured a VTI interface between two 2921 routers.  The link between the two routers is 100 MB, but the tunnel does not seem to be able to spend a lot more traffic.  I noticed a few differences between the MTU and bandwidth in the

Hello everyone, I m looking for the best configuration to restrict a user read-only. The restriction must be configured through CLI not GANYMEDE. Material: 3750 (probably not interesting for that matter) More old IOS: 12.2 (53) SE1 The user should be

Hey, I heard that IOS 15 is basically 12 with more features. Remain the same all orders or are there changes in the structures of command for some parts?

Hi guys I use the level of privilege 15.2 and in this version, that I can not get the startup-config under some of IOS (in this case, IE 7) I have no problem to get it from the earlier version, also to 15.1 Router #sh privileges Current privilege lev

ASA 5510 can be configured as bridge mode and always send Netflow information to a collector? We have a PIX connect internal network to the internet. Because PIX does not support NetFlow, as temporary solution, we thought to a 5510 ASA between the PI

Hello, I have a copy of the LMS 4.0 and want to install it on Windows server 2008 R2. Right now I get the popup that says that this is impossible because the platform is not 2003, 2008 but did not mention 2008 R2. Does anyone know of issues installat

Hi all If you hot-swap a map of 100M with a module of concert in a 4500 switch, what happens to the running-config?  You don't have to hand versions of module. Thanks in advance, Jason

We use freeFTPd for saving the Voip, now you want to save all routers & switches the set, running this free program for them? If yes, can someone show me the exact CLI to copy start-config to it? I ran "copy start ftp"--> enter the server IP when you

Hello We have 1801 router and you want to configure for PPPoE.As our ISP provided ADSL connection with the following parameters: Encapsulation: PPPoE Multiplexing: LLC based VPI = 0 VCI = 103 Login = xxxxx Password = xxxxx IP: Dynamically by ISP I'm

Hi all I use the EEM to be notify by mail when my Wo OSPF changes; I use OSPF in tunel int, so I know when the tunnel is down/up. My script works fine but sometimes I don't get any mail while Wo is changing, so I can receive mail with 'up' so that I

Dear Sir. Praposed connectivity for voice between neighborhoods General remote IP phones to analog phones is regarding the attached flowchart. Cisco 2821 routiters with IOS 12.2 are interconnected (v.35) line using rented between HQ FOR REMOTE SITES.