1390 WLAN - connects but disconnects / reconnects frequently

Similar Questions

• WLan connected but receives no package - Satellite A300

  Hey my model is Satellite A300, which I went down to XP. After not using my laptop for two weeks, my wireless is dead and will not work.

  Problems:
  1. it used to automatically detect IP and DNS and gateway and all that, but no more

  2 so I put in place manually and that it is connected now - but still, it doesn't receive all packets, even if it sends packets.

  It's painful sssssssssssssooooooo... Help, please.

  Oh, by the way

  -Correct encryption
  -Good wireless driver
  Œuvres-LAN
  -J' tried to format my computer - that didn't work
  -Use all the drivers of Toshiba Europe, Australia, and Intel Web sites
  -Can connect to the network but not the Internet.
  -test of ping with my manual Gateway - 4 received, 4 sent, none lost

  Thank in advance for your help!

  Reset you the router? Unplug the power connector on the router, wait 10 minutes and then plug it. Maybe it still works.

  Check the settings in the router and windows. All devices must use the same standards.
  Search on the Toshiba site, if you have the newest BIOS and check if the TCP/IP settings are on automatically and in the router.
  Try turning off the router MAC address filter.

• Equium L40 - 17 M: WLan connection but the light no longer works

  I recently transferred my laptop Equium L40 17 M. ROM Vista to Windows 7 64 bit and since that time my WiFi light has not worked - of ideas?

  Help!

  Hello

  I guess you are not able to activate the WiFi network and therefore the wifi does not work in Windows 7.

  First of all, you must make sure that the WLan card driver has been properly installed and that wireless network card has been recognized in the Device Manager.
  No yellow exclamation point must be visible in the network adapters.
  Here is a page with drivers WLan:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  I think that your laptop support REALTEK RTL8187B WLan 802.11(B/G) card so you have to choose Realtek WLan driver.

  In addition, you should make sure that WLan is enabled;
  You must switch the WLan POSITION to allow the led WLan
  In addition, you have to use FN + F8 buttons to choose the wireless network adapter.

  If the buttons Fn would not work, then you must install the VAP (value added package) and Flash memory card Support utility. You can choose the tools available for Satellite L500...
  I did and it worked

• On Windows XP, 3G modem connection is disconnected frequently

  I bought an Airtel 3 G modem for internet access, the modem is installed properly on Windows XP, but the connection is disconnected frequently to every 5 minutes. Help, please.

  Hi JayTiwari,

  ·         What is the brand and model of the computer?

  ·         You are able to use any other USB device on your computer?

  You try to run the cycle of power from the laptop or desktop computer. Subsequently, check if you are able to use the USB modem on your computer.

  a. disconnect all external devices from the laptop or desktop.

  b. remove the battery from the laptop (only if it's a laptop).

  c. press the power button on the computer laptop or desktop for 10-15 seconds.

  d. Insert the battery in the laptop and restart the computer (only if it's a laptop).

  Hope the helps of information. Please post back and we do know.

• I can not connect Dell Wireless 1390 WLAN Mini Card to WAP4410N

  Hello

  I have dell inspiron 640 m with Wireless 1390 WLAN Mini-Card, and it connects perfectly with any other routers.

  but I can't connect it to the CISCO WAP4410N router! I tried several times but no way.

  I can connect IPAD, Samsung Smart tv, Denon portable radio and toshiba PC but not Imy nspiron computer network.

  I think that my WIFI cannot get th WAP4410N IP address!

  Any expert can help me?

  These products are processed by the Cisco Small Business support community. (URL: https://supportforums.cisco.com/community/netpro/small-business )

• Satellite L300-135 see WLan network but will not connect

  Well well, (new laptop) initially, it worked with my BT hub at home... then decided to not stop working - receives no signal or response from the router - even though other laptops in the House can connect without any problems

  and now the Wireless does not work - IE. I can see the wireless connection but cannot connect.

  I don't know that the wireless is not cut (until someone suggests)

  I looked for more up-to-date drivers, but nothing seems to work.

  Help, please!

  Hello

  First of all, you should check if your wireless network card is correctly recognized.
  I mean to check in the Device Manager!

  Your wireless network card must be the Realtek 802.11 g (RTL8187B)
  Download and install the latest driver WLan in the Realtek page.
  Then update the BIOS.

  Finally, reconfigure all WLan settings.
  In the Device Manager-> properties-> Advanced tab card WLan disable energy saving settings and check the other parameters that may affect the connectivity.

  Good luck

• Whenever I try to log on to the administrator account, it will start to connect, but immediately disconnected return.

  Original title: why my account automatically disconnect?

  I am running Windows Vista Home Premium.

  Whenever I try to log on to the administrator account, it will start to connect but then before he's even changed screens, immediately disconnect back.
  I can connect to it using safe and I ran Anti-malware, Microsoft Security Essentials and Advanced System Care and they have all come without any problem.
  Now, I guess I'm using an account with administrative privileges but different. I just need to open Windows Media Center, but every time I try, it says: I'm on the guest account. My machine won't let me create a new account, delete other accounts, or even to change the passwords. In addition, a random ASP.NET account appears and I can't remove it.
  I don't understand what I could do wrong. Any help is greatly appreciated.

  Hi Jorgomli,

  1. you receive messages or error codes when you try to connect?

  2. you remember to make changes to the computer before this problem?

  Step 1:

  Because you can connect to the account administrator in safe mode, you can try to create a new safe mode administrator account and check.

  Check out the link:

  Create a user account

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Step 2:

  If still face problems, then you can try setting the default Administrator account and check if you can solve the problem.

  a. click the Start button

  (b) in the Start Menu, click all programs followed accessories

  c. in the menu accessories, right-click on command line option

  d. in the drop-down menu that appears, click on the "Run as Administrator" option

  e. If you have the User Account Control (UAC) enabled, you will be asked for permission before the opening of the command line. You simply press the button continue if you are the administrator or insert password etc.

  f. in the command prompt window, type the command net user administrator / Active: Yes and press ENTER.

  g. close the elevated command prompt.

  h. log (in the Start Menu) and you will see your new administrator integrated next to your current account.

  i. click the photo icon display built-in Administrator account and connect to it.

  If the problem is resolved, then you can create a new administrator account and check.

  You can try to create a new administrator account by following the link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  You can also try disabling the default Administrator account using the command

  NET user administrator / active: No.

  Hope this information is useful.

• I have paid, downloaded CC but when I try to download any application log in the box appears, I connect but he immediately returned to the top with "you have been disconnected. I'll just round and round. Someone at - it ideas?

  I have paid, downloaded CC but when I try to download any application log in the box appears, I connect but he immediately returned to the top with "you have been disconnected. I'll just round and round. Someone at - it ideas?

  Hi Steven,

  Please check the contents of the link below and follow the steps mentioned in it to resolve the problem you are experiencing:

  https://helpx-internal.Corp.Adobe.com/content/help/en/creative-cloud/KB/unable-login-creat ive-cloud - 248.html

  Please let me know if this helped.

  -Harsha.

• Wireless connection keeps disconnecting - Satellite C650 16U

  Hello

  My wireless connection keeps disconnecting frequently and I have to reconnect manually. I don't think that it is a router problem, that this does not happen with the other laptop which is used in my house. Any ideas why this is?

  Thank you

  Hi mate

  I recommend you in Win 7 the power management of the energy saving settings.
  There you can change (disable) WLan Card to save energy.
  It helped in my case.

  Please also check this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59177

  As I have said; power management setting is the key, you must also update the WLan driver!

• Satellite Pro L550 - Realtek RTL8191SE Wlan connection issues

  Hello

  Affected by a big problem with my WLAN connection which is ongoing for about a month.
  I have problems with a very inconsistent connection.

  To start, turn on the laptop of its climate 50-50 I'll successfully connect to my internet. Once connected I constantly disconnect and reconnect, never reached a point of stability, as long as possible without hitch is about 30 minutes, and after this point it will repeat the process above in one or two minutes, making it impossible internet usage.

  After following various checks, I can confirm that this is NOT a router problem:

  -Several other devices around the home connect without the same problem
  -Have you tried the reset and restarted both modem and router without result
  -Used new Ethernet cables and checked the other son of bends or damage
  -Tried to change the frequency of router and the channel for better connectivity with no result
  -Tried to change the location of the router, the closest pass to the laptop for a greater power of the signal without any positive results

  Whenever he logs off, I go through a laborious task repetitive troubleshooting and although sometimes it solves the problem, so that it does only temporarily.

  Updates on computer and controls are as follows:

  -Install the latest drivers for my network card
  -The latest version of the BIOS for my laptop
  -J' tried UN-installing software and remove driver in Device Manager in the case of a corrupted driver, after re-booting works temporarily and then breaks down in the first 5 minutes
  -Tried using windows troubleshooting, which sometimes displays a message on my gateway by default, I don't know what that means well as
  -Tried to use other means of verification, connectivity doctor etc., no results
  -Tried to reset network cards
  -Tried to use an earlier version of the network card to check if the new drivers were the problem - no result
  -Tried resetting IP addresses IP conflict with other devices in the House, no results
  -Played hundreds of reboots

  I would like to point out that when using the LAN on my laptop my connection is quite well and I have the experience without interruption, I have also contacted my ISP to ask if there is ongoing network maintenance tasks and check if the internet I receive is consistent.

  Computer laptop specifications: -.

  Toshiba Satellite Pro L550
  Network card: Realtek RTL8191SE
  OS: Windows 7 x32bit

  The whole process is infuriating and I am at my wits end as to what to do, is, fuck my network card?

  NB:

  This could be a problem as the dust inside my computer laptop on the map, causing interference?
  The problem is much more prolific when I use Skype - might be a bandwidth issue?

  Open to the suggestions of many, and any help will be appreciated.

  Thank you.

  And all this occur with clean Windows 7 preinstalled that you got with your laptop (factory settings)?

• Satellite Pro L20: WLan connection is limited to 5 meters

  Hello
  My Satelite Pro L20 is connected to the Orange livebox, but cannot go further than 5 meters and disconnected. Any help?

  Hello

  One question;
  Where is placed the WLan router?
  In the same room you book or are the walls between the router and the wireless network card.

  Sometimes, this could be a reason for a lower range of WLan.
  But we must try first of all to enable full implementation of card WLan.

  Please enter the WLan card properties. (Device Manager-> right click on the WLan card-> properties)
  There you can select the Advanced tab. You should see the power of the economy option of-> please turn it off.
  In addition, you should find there more options that could increase the range of WLan and performance. Please check.

  Of course a new version of the wireless network card could also improve the performance of the WLan card.
  I m not sure what card have you use but please consult the WLan and Toshiba card manufacturing site.

• Tecra M9 PTM91E: WLan Intel 4965AGN disconnect every few minutes

  I have a laptop M9, model PTM91E. The wireless connection keeps disconnecting (then again in reconnecting) every few minutes. This happens on all the wireless networks in that I try to connect. Here what I have on my laptop: -.

  Intel Wireless WiFi Link 4965AGN
  11.5.0.32 driver version
  26/09/2007 driver date
  XP Pro

  Toshiba suggest to upgrade to Windows Vista, I nigtmares on something.

  Someone else has the same problem? All solutions?
  Thank you

  I read on the similar topic on a satellite A210 and with the Atheros WLan card.
  The solution was a update driver BIOS and WLan

  So check it out.

  Good luck

• Problems connecting to a wireless connection that disconnects every time

  original title: wireless

  My wireless connection disconnects whenever I have change the sites while surfing and even within Web sites.  How can I stop
  It is to do this?  The only way to get reconnected is to 'fix '.

  Hello

  1. do you get an error message? If Yes, what is the exact full error message?

  2. what operating system are you using on your computer?

  3. what web browser you use to surf the Web sites?

  If in case you are using Windows 7 as OS then try the steps below to solve the problem:

  This problem can occur if authentication enable IEEE 802. 1 X for this network checkbox is enabled. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period.

  Method 1: Disable IEEE 802 authentication. 1 X

  To disable authentication IEEE 802. 1 X, follow these steps:

  (a) click Start, type ncpa.cpl, and then press ENTER.

  (b) right click on your wireless network connectionand then click Properties.

  (c) click the wireless networks tab.

  (d) under preferred networks, click your wireless network, and then click Properties.

  (e) click on the authentication tab, click to clear the authentication to enable IEEE 802. 1 X for this network check box and then click OK twice.

  Method 2

  See the following help link and check if that helps.

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know the status of the issue.

• My wireless connection status shows that I am connected but I did "no internet access.

  Original title: internet connected but shows "no internet access" why?

  I have a gateway laptop and everything suddenly I can't access the internet.  My wireless connections shows that I am connected but I did "no internet access?  I tried to disconnect and reconnect, but that has not worked.  I tried troubleshooting and it says there is a problem connecting with my modem, but it is impossible because all other computers cell phones/Ipod work correctly on the same connection.  Can anyone help?

  Renee

  Hello

  You did changes to the computer before the show?

  I suggest you follow these methods and check.

  Method 1: Remove all the wireless networks, listed in the network and sharing Center.

  1. click Start and select Control Panel.

  2. open the network and sharing Center.

  3. click on manage wireless networks.

  4 remove all wireless network listed in this list.

  5 restart the computer.

  Select your wireless network and connect (if course, enter your password). Check if you see exclamation of yellow color on the bar strength wireless connection.

  If the method above does not work, proceed to the next method.

  Method 2: I suggest you try the steps from the following link.

  Wi - Fi and in Windows network connection issues.
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  If the method above does not work, proceed to the next method.

   
  Method 3: Reset the TCP/IP stack.
  
  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself: http://support.microsoft.com/kb/299357 .
  If the same problem still persists, then try the next method.

  Method 4: Perform the steps from the link to set up a new wireless connection.

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  I hope this helps!

• Tecra Z50-A-130 - LAN over WLAN connection

  My Tecra Z50-A-130 with Windows 7 Professional prefer a WLAN connection over a LAN connection.

  When I have a LAN connection available I prefer the LAN connection (speed is better), but my laptop auto activates the WIFI connection.

  Is it possible that my laptop active automatic connection of the local network when available, prefer it over the wireless LAN?

  Why you n t turn off WiFi if your laptop is connected to the local network?

  However, usually Windows controls this connection automatically to change this, you will need to change the priority.

  1 click Start, in the search field, type view network connections.
  2 press the ALT key, click Advanced Options, and then click Advanced settings...
  3 select Local area connection and click the green arrows to give priority to the desired connection.
  4 after organizing network connections available according to your preferences, click OK.
  5 the computer will now follow an order of priority when the detection of the available connections.

  More details here:
  http://Support2.Microsoft.com/kb/2526067