2 WGA600Ns?

Similar Questions

• WGA600N no link

  I can't connect the WGA600N to the router and it is for me that there is no adapter conncected game. I try to manually connect the adapter for games but I can't open the ip address I never had this problem before I used to connect all the time. What included I do.

  For the Belkin router default IP address is 192.168.2.1. If you connect to games to the router and try to connect to the configuration of the adapter for games page you wont so able to access the configuration of the adapter for games page.

  Then connect the adapter to your computer via an ethernet cable games. Assign a static IP address to your computer... (Click on the Start button > settings > Control Panel > Network Connections - right click on the icon to connect to the Local network and go to properties - in the 'Général' tab select "TCP/IP Internet Protocol" and click on the properties button - select "use IP address following" - provide the IP - 192.168.1.5 subnet mask - 255.255.255.0, default gateway - 192.168.1.1 - favorite DNS 192.168.1.1)...

  Once assign you a static IP to your computer... Open the prompt on your computer and then try to ping games adapter. The games default IP adapter is 192.168.1.250... If you receive response messages... Then, open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type in 192.168.1.250 and press ENTER... Let the empty user name & password use admin lowercase...

  The Setup page of the game adapter click the 'Home' tab and then click the sub-tab "Wireless" and you need to enter the settings of your Belkin router (SSID, channel, Security Mode and security key) wireless and click on save settings... ' ' And then the 'Home' tab, you must click on the tab 'Network settings' and below change the IP address of the adapter for games of "192.168.2.250, subnet: 255.255.255.0 default gateway: 192.168.2.1" and click on save settings...

  Once that all the settings are saved on the game card, then unplug the ethernet cable from the adapter for games and then unplug the power to the adapter for games... wait 30 seconds and then connect the power supply to the adapter for games... and remove your computer's static IP address...

  Once again, on your computer, open the command prompt and type "Ping 192.168.2.250" and click Enter and check if you have all the answers... If so, this indicates that your game card is ready to use...

  I think that these steps should solve your problem.

• WGA600N Wireless N does not connect to the N, G speed only

  I have a WGA600N Wireless-N game adapter and a router WRT160N (v3).   I can't get the adapter for games to connect at speeds of G.    I tried to adjust the adapter for games to use only the N band, but then he used to see even the router at all, it does not detect the network period.    If I have configured the router to N-band only, the same issue happens (though ideally I need in mixed mode for my laptop anyway). I have connected the WGA600N directly through the web interface of the intellectual property and has tried a variety of settings, but no help.  I can clearly see in the State of the adapter of game that it is connected to an 11g-force when the value of mixed mode.    I use WPA encryption if it matters.

  I have the adapter for games within a few feet of the router at this facility, so I don't think it could be a question of signal strength, but unfortunately I do not have another Wireless-N to test against the router.

  Any ideas?

  Just to follow up, I was able to get the speed 11ng use WPA2 AES mode only to work.   This isn't the perfect solution for me because my PSP only supports WPA WPA2 not - however N speed for my consoles wireless is more important, so I'll just have to manually change my router settings any time I want to connect any WPA or less peripheral encryption online.   Not perfect, but better than nothing solution.

• Game WGA600N adapter used to connect to the router WRT310N but not now.

  I have a game WGA600N adapter that connected perfectly to a WRT310N router. Has worked for 2 months. Then one night while being connected via the adapter for games, connection has been lost. I was unable to reconnect since. I have reset the router and adapter of game (full reset) and still not connecting. I thought that it could be the signal, but I put the adapter for games about 3 to 4 feet of the router and it still not connect. In addition, when you browse the installer on the adapter for games I can see my network SSID only one part of the time. In this case the weather in normal or next to the router as location mentioned above. Whenever I go through installation and network appears, I continue through the process, but I get an "unable to connect" alternation and the message "network found" that opens. By clicking 'next' never connects to the network. As stated, it worked fine for 2 months before this problem. I thought it was the router and replaced it with the same type and not luck. I must also stress that I was able to connect to an old WRT54GS router without problem. I also tried to connect wireless to the router WRT310N with another PC and had no luck in the connection... However he also finds and connects to the WRT54GS router without a hitch. I am lost at this point.

  As you have arelady set up your WAG600N with WRT54GS router and it worked perfectly well. Then I think the problem lies on WRT310N router. Maybe your game adapter and computers are not connect to your wireless network. You must change some settings in your wireless router. Follow this steps on your router and I think this will make your adapter games work perfectly well.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Fix the Radio band to wide - 40 MHz and change the broad Channel 9 and channel Standard 11 - 2, 462 GHz... Wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• WGA600N and uTorrent... capped at 200 Kbps?

  I recently installed the WGA600N and hooked up through my card pci ethernet (gigabit capable), and everything looks good except for downloading via bittorrent.  It is connected to a DIR-825 in the 5 GHz range to N only.  The DIR-825 related forces signal about 70 to 75% and a rate of 270 to 300 Mbps.  However, in the connection network icon in the right sidebar below shows speed: 100.0 Mbps.  Not sure why this will not jump above 100 Mbps with the ethernet card compatible gigabit and forces signal strong enough?  With all that being said... If I upload a file via the web/firefox I can hit speeds of up to about 600 Kbps... BUT, if I run a bittorrent via uTorrent I out cap to a max of 200 kbps download speed.

  Am I missing a setting on the WGA600N?  Why would I capped at 200 kbps download via a bittorrent client speeds?  In addition, all the drivers are updated, my port is open, and I was able to reach speeds of 600 Kbps in uTorrent via another D-Link N adapter, so I know that's not my internet connection (Fios).

  Thanks in advance for any help!

  I solved this problem.  My connection speed of global download in uTorrent preferences has been somehow set to 200 Kbps max.  So my question has nothing to do with the WGA600N.  Sorry for the waste of space here.

• The WGA600N can switch between 2 channels?

  I hope that I am not on something, but I can't find an answer to my question.

  I have the WRT610N simultaneous dual band router paired with a WGA600N wireless dual-band adapter.

  With the router, I set myself to 2.4 and 5 GHz channels separate SSID and WPA2 encryption keys.  My adapter, although it can 'see' the two networks, connect only to one. On the product for the WGA600N support page, it says clearly, "dynamically travel channels and wireless networks based on the quality of the actual signal and a link for maximum availability and reliability of connection."

  My question is... How can I activate my game card work on the 2.4 and 5 GHz channels to find the best connection?  It seems in the WGA600N Setup, it makes me choose a channel.  Both channels on my router must be on the same SSID and the same encryption key for the adapter to switch back?  Should I switch to WEP mode?

  On your Linksys card, only a single frequency could serve both (2.4 GHz or 5 GHz), although it could pass the frequency... Access your game card and go to the Wireless tab on the Basic tab, select 802.11 2.4 GHz and 5 GHz band... 802.11 mode should be mixed 802.11na, 802. 11A, 802.11ng, 802.11 g, 802. 11 b, let the rate of automatic transmission and channel width should be 20/40 MHz...

  Be sure to set the security WPA (not WEP/WPA2) wireless...

• Question of WGA600N

  I was wondering how many Mbps is the WGA600N and if it would work on my PC?

  Also I was looking for a wireless game adapter because the current that I am using (not linksys) behind and show all the one or two seconds when I play a game. Can someone recommend me an adapter that would be great for the games? I am currently using linksys WRT320N router.

  It converts wired Ethernet-ready consoles game to Wireless N network connectivity... It works without drivers on Xbox, Xbox 360, PlayStation 2 or 3, and GameCube...

  It should report > or = to 270mbps on the 2.4 GHz band, but with the band of 5 GHz range will be much better if it'll get 130 or 140mbps...

  You can go with adapter WGA600N game, also you need to adjust settings on the adapter for games and your router wireless, make sure the wireless settings are identical...

• WRT610N and WGA600N game help?

  Hey everyone I need help to find the best settings for wrt610n for games and it goes the same for the wga600n. whenever I play a game the connection falls for about 1 minute then I can play again. as he always says something about the strict firewall whenever I play war gear please help. Thank you

  I figured out problem that the triclk is if you play on a console or anything that allows you to take off the firewall, you need to do DMZ is enter the ip address for what you play and BOOM the connection is good. I turned on the 5gz return string and it works perfectly since there is no firewall to slow the connection on my xbox 360

• WGA600N default for WPA/WPA2 TKIP/AES despite settings saved after reboot

  Strange comment here: when I select in the web the WGA600N utility: WPA/WPA2 TKIP/AES after restart only WPA2 and AES only, always default.  I saw it twice.

  Anyone has an idea why it is doing this? My D-Link 825 security is set to WPA2 with AES encryption only algorithm.

  I read that the maximum speed is obtained by forcing these settings and I tried to get the router and bridge to match.

  As I pointed out in the "New Firmware" thread, the problem is solved with the release of 1.05.

• WGA600N as a WRT610N wireless bridge?

  In my home office, I the WRT610N and would like to make a bridge of anti-piracy N for my press room.  I have 4 items that I would like to link to the top here.  Can I use the WGA600N and range from the network to a switch Jack and connect all my items?

  Include items

  Wii

  TV (Yes the tv uses a socket 10/100 for the software updates)

  PS3

  DirectTV box

  Yes, you can do it, but you must set the IP static/manual on the devices that you would connect to the switch...

• LINKSYS adapter WGA600N

  Is someone can you please tell me if the power adapter supplied with the Linksys WGA600N is auto switching (110/120 and 220/240 VAC)?

  Thank you!

  Specifications of WGA600N power...

  Input voltage: 110 V ca; Range of input voltage: 110V AC 220V AC...

• WGA600N and the WRVS4400N

  I have problems with the connection of the wireless game adapter.  He is able to find my router and it connects to where he asks my security key.  I enter the key and I checked it came directly through my eyes and someone else and I cannot get it to connect.  I really need to keep my WRVS4400N in the House to protect my periphery of Home Office, but I can not get the adapter to connect and do not want to buy another router woreless.  Any suggestions?  What settings can I give show you where I went wrong.  I don't really have chnged much the default value on the router.  I have a few settings to restrict access, but they are specific MAC address.  I also disabeld these and tried and it still does not work.

  can't really think of anything except recheck that the WPS is disabled in your WGA600N because WRVS4400N does not support. This feature has been examined in the link below:

  http://KB.Linksys.com/16319

  also, since you mentioned that you use MAC address filtering (at least that's how I interpreted ' some access restriction settings, but they are specific MAC address ' ) to ensure that it is disabled when you try to configure the settings on the game adapter wireless

• WRT160N, it will work as a bridge towards WGA600N?

  I have a Linksys WGA600N games adapter hooked up to my TV receiver satellite.  I had a crush and lost my previous Setup, so I replaced a modem AT & T with the modem/gateway 2 wire of AT & T, then, I must get my access to internet gaming adapter again.  Can I connect the WRT160N to my AT & T 2 wire gateway to provide access to my WGA600N?  AT & T gateway is a router/modem and is wireless, but I would be hard wire the WRT160N than.  I would use only the WRT160N as an access point or a bridge between the gateway and the adapter for games and any other wirleless PC you may want to use.

  Also, I should create another wireless network, or should I use other wireless through my AT & T gateway?

  Yes the games adapter will work with AT & T Router.As your game adapter is an adapter of series N, but its a Compitable backwards and it can connect to a network of G and goes perfectly well with your G series router.

• Does not connect WRT310N a WGA600N adapter games had worked for 2 months now?

  I have a WRT310N wireless router and connected an adapter WGA600N Wireless 2 months ago game. Both purchased and installed at the same time. Works perfectly for about 2 months. Then one night when logged in it just dropped connection. I tried to solve the problem... reset router... reset the game device wireless (including the reset total) and not luck. I thought that maybe the router went buggy I went and bought a new WRT310N. Who has not corrected the situation. Now, whenever I try to connect to the router the WGA600N will pick up the router (see the SSID) but if I update the list may disappear. I thought maybe it was signal strength, so I moved the WGA600N down next to the router (in about 5 feet). Same thing... wouldn't connect... even if the signal seems to be there all the time. I'm at a loss as to what may be the problem. I thought about doing a new WGA600N but it becomes expensive. Any ideas?

  I should add that the WGA600N connects to a WRT54GS router without problem. I also tried to connect to the router WRT310N with another PC wireless, and it wouldn't connect. Currently, I run the game through the older router device but is not what I want to do what is not my router.

  You set up your WAG600N with WRT54GS router and it worked perfectly fine. Then I think the problem lies on WRT310N router. Maybe your game adapter and computers are not connect to your wireless network. You must change some settings in your wireless router. Follow this steps on your router and I think this will make your adapter games work perfectly well.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Fix the Radio band to wide - 40 MHz and change the broad Channel 9 and channel Standard 11 - 2, 462 GHz... Wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• How to reset the password on my adapter WGA600N game.

  I have an adapter WGA600N game that some how (I blame my friends girls) ceased to connect to my wireless router.  When I try to open it to be asked a password. All my standard ones don't seem to work. How can I reset it so it allows me to select a new user name and password. I tried the reset on the back button and that does not seem to do. I want to go back to the point where I bought reset it and start over from scratch. The documentation is of no help.

  Have you tried the password "admin" with a username "in white"?  This could be the same as the Passover "default" for most Linksys routers.