4 FC by FI uplink ports. But what a single port to send the addresses of WWPN vHBA?

Similar Questions

• stop the ethernet uplink port will cause the port of the unit down

  Dear all,

  I want to make sure that this kind of network traffic will communicate internal fi.

  I've disabled the uplink port and found the path of material has also declined.

  Port of the device must road toward uplink port and then back to UCS server?

  Thank you for the clarification.

  Best regards

  Dennis Dai

  Expected behavior.  By default, if there is no uplinks online & fwd, then all links South (Server binds and the ports of the device) will be used also to the bottom.

  See the explanation of Abi here for more information how to change this behavior.

  https://supportforums.Cisco.com/thread/2187144?TSTART=0

  In short, we must change policy control of the network of the way of the material in the Hardware tab.

  Kind regards

  Robert

• what I'm typing goes to the address bar

  tapping on any program; Messenger, games mode window or window google chat (the one that can be opened as a separate windown on gmail); Suddenly the text is not written on the ground, sometimes there is a clicking sound, and when I press on enter, all text is displayed on the address bar of firefox as if it was a bing search engine.

  If firefox is not open when this happens, pressing enter will automatically open firefox to search bing what I was typing on other applications. If the computer its on idle, when im away from nothing, I still hears the sound form successive clcik.

  Look for the sound click on Control Panel > sounds > sounds I found is the sound of "beginning of navigation of windows.

  I run kaspersky analysis full, malaware bites free version, I removed all the toolbars (except the toll of google bar that always works the tweak version number of Pentecost), nothing stops her.

  I don't know what else to do, hope someoen whit a similar or same problem help me

  Thank you

  Do a clean reinstall and remove the Firefox program before (re) install a new copy of the current version of Firefox.

  • Download the full Firefox installation program and save the file to the desktop
    http://www.Mozilla.org/en-us/Firefox/all.html

  If possible to uninstall your current version of Firefox to clean the Windows registry and settings in the security software.

  • Do NOT remove the "personal data" when you uninstall your current version of Firefox, because this will remove all profile folders and you lose personal data such as bookmarks and passwords including data profiles created by other versions of Firefox.

  Remove the Firefox program before installation newly downloaded copy of the Firefox installer.

  • (32-bit Windows) "C:\Program Files\Mozilla Firefox\"
  • (Windows 64 bit) "C:\Program Files (x 86) \Mozilla.
  • It is important to remove the Firefox program to delete all the files and make sure that there is no problem with the files that were the remains after uninstallation.
  • http://KB.mozillazine.org/Uninstalling_Firefox

  Your bookmarks and other personal data are stored in the Firefox profile folder and will not be affected by a uninstall and (re) install, but make sure that 'delete personal data' is NOT selected when you uninstall Firefox.

  If you keep problems also create a new profile.

  • http://KB.mozillazine.org/Profile_folder_-_Firefox
  • http://KB.mozillazine.org/Profile_backup
  • http://KB.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

• Firefox automatically adds the port number in the address bar when it is not.

  I work for an ISP company that implements regular routers for a customer locations. One of the things I need to change about it is to assign the management port 8080. For example, 192.168.0.1:8080. Once I try to install a new router that Firefox automatically assume I want to go to the same port 8080 and automatically concludes for me. Since the new router has not been configured with the 8080, yet I can't. So basically I would like to see if I can stop Firefox automatically enter this bit of information. It is very annoying and even more annoying that I have to use another browser to make changes since Firefox can not. I found a similar fix posted when Firefox will automatically ".www" but which did not fix my problem.

  Disable the URL bar auto-complete feature. You can always select an address already used by the arrows down on the drop-down list of AutoComplete, but Firefox won't add characters to the URL as you type. Here's how:

  (1) in a new tab, type or paste Subject: config in the address bar and press ENTER. Click on the button promising to be careful.

  (2) in the search box that appears above the list, type or paste the filling and make a break while the list is filtered

  (3) double-click the browser.urlbar.autoFill preference to change its value from true to false.

  Who help me?

• Is it possible to find what part of my code sends the e-mail.

  I have a problem as follows: an e-mail is sent as a daily alert to the list of recipients. The sender is our group of e-mail to the development team. One of the recipients email is no longer valid. Therefore, every day, we receive e-mail back "ofyour message has not reached some or all recipients planned." because of the invalid recipient. Nobody knows where is the list of recipients to delete this incorrect e-mail address. The code was written years ago by a developer. But we need to delete this incorrect e-mail address to no longer receive this daily email by anyone.

  I tried to get across the code base, but the code is massif, scattered on several servers and several patterns.

  Is my question, there a way to detect this email (which part of the code, package, function, or procedure)?

  Hawk333 wrote:

  I have a problem as follows: an e-mail is sent as a daily alert to the list of recipients. The sender is our group of e-mail to the development team. One of the recipients email is no longer valid. Therefore, every day, we receive e-mail back "your message has not reached some or all recipients planned." because of the invalid recipient. Nobody knows where is the list of recipients to delete this incorrect e-mail address. The code was written years ago by a developer. But we need to delete this incorrect e-mail address to no longer receive this daily email by anyone.

  I tried to get across the code base, but the code is massif, scattered on several servers and several patterns.

  Is my question, there a way to detect this email (which part of the code, package, function, or procedure)?

  sending e-mail code cannot reside in the DB or a part of the core application code.

  As far as I KNOW, the best place to start the detective is associated when the email is sent and correlating what code is / was running at this time.

  CHECK RUN UTL_MAIL;

  RUN UTL_SMTP;

• What is this small triangle in the address bar just to the left of the button refresh which turns blue when the mouse passes over it?

  Installed modules include:
  Adblock more
  Add to search bar
  Easy YouTube Video Downloader
  Hidden ELEMENT Helper for Adblock
  Flagfox
  Ghostery
  NoScript
  Tab Mix more
  TinEye Reverse Image Search
  Vertical toolbar
  WOT

  Hi ApolloSerenus,

  You are probably referring to location bar history. If you click this button, a list of Internet sites must appear. This article will give you information about the history of compensation.

  You should also look Awesome Bar - find your Firefox bookmarks, history and tabs in the address bar for other cool things you can do with the address bar.

  Hope this helps!

• What Contacts are used when send the email from the Mail application?

  I have a sky email Yahoo where all my contacts are available.     I use the people App where my contacts are available.   When I want to send an email using the Mail (which is related to my emails from sky) application, then all my contacts don't EXIST - why.

  Will you please explain in simple language please because I'm not technical interest

  OT: Contacts

  Hello

  I suggest you try the steps from the following link to import the Sky email account contacts.

  Add, import and export of contacts
  http://help.sky.com/email/managing-your-contacts/adding-importing-and-exporting-contacts

  To further support on behalf of heaven, I suggest you show in sky support forums.
  http://helpforum.sky.com/T5/sky-Yahoo-mail/BD-p/emailsandtools

  I hope this helps.

• ESXi 5.1u1, Mo 2xsata3 ports, you want to add SSD cache but what port?

  Hi all

  This is my first post and I'm not speaking English, so I'll try to explain my question in the best conditions.

  We run esxi 5.1u1 on a small server with office components:

  -i5 - 3570 k [could get i5-3570 non - K]

  -z77 motherboard (msi g43) [could get Q77 Board from gigabyte]

  -16 GB of ram ddr3 1600 mhz non - ecc

  -2xHDD western digital RED 2 to each, no raid

  -backup to NAS

  and on 10vm between linux and windows guests (usually only 6 are in normal production [AD, FS, PBX), to manage a network of 4 desktops.

  We ask to add a SSD 120gbSATA3 caching, using build-in functionality of ESXI 5.1u1, but we have a problem on the choice of the correct configuration of the disk since we only 2 port sata3.

  1. Hard drives are sata3 and actually connected to the sata3 ports 2 (Controller intel);
  2. We've got to other 4-port sata2 on a different construction to the controller;
  3. We can afford a raid at the moment card;
  4. should we put on the benefit from the speed of cache sata2 ssd, or the only way is sata3?

  Thanks in advance.

  You can put on sata2 SSDS (interface is backward compatible), but you will suffer serious non-performance. With sata3 you get 600 MB/s transfer speed, with sata2 just 300 MB/s (taking into account encoding 8B / 10B). And consumers of today SSD sequential transfer rate is approaching even this maximum limit of sata3 interface (i.e. Samsung 840Pro: 520 / 540 MB/s). If you put on sata2 SSDS, you will seriously degrade its performance, perhaps to half of its capacity. If you want to use for caching SSDS, I wouldn't put the SSD on sata2 interface.

  I would of put HDD sata2 rather (and use for SSD sata3 ports). With the exception of the disk cache, without disk hard common has over 300 MB/s transfer speed. He could suffer from degradation in performance a little too much when using cache, but is not as much as the SSD...

• Half of the blades fell when creating a new channel of uplink port?

  I have a pair of 6248UP fiber interconnection (A and B) with blade servers connected. The switch upstream is Nexus7k. Fabric A and B each right has now a channel of uplink port to the Nexus switch upstream. I add a new Nexus switch to connect to the interconnection of fiber. The plan is to have uplink some VIRTUAL networks for Nexus one pass and uplink some VIRTUAL to the second Nexus switch networks.

  After that I configured the new Nexus switch with a channel port (only allowing some VIRTUAL networks) and corresponding port created on fabric channel A and B, new ports-channels have increased. However, half of the blade servers were down after that. What could be the reasons for this problem? Is it because half of the blades have been pinned dynamically on the new channel port, but the new port-channel side Nexus allow only some VIRTUAL networks?

  Is there a way to configure the Channel ports on fiber to interconnect with only the trunk through some VIRTUAL networks? for traffic from the server would not be sent to the port-channel where VLAN server is not allowed?

  Thank you

  In general, all NICs for/vhba of a fabric are declining, if all uplinks of this fabric are declining.

  It's not clear to me, what you're trying to achieve?

  If you create a global VLAN (for the two fabrics), this vlan is automatically inserted in all dependent North trunk links, unless you configure a leaking installation

  (http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns224/ns944/white_paper_c11-692008.html)

  Create a new vlan on UCS requires of course also this vlan is created on the switch connection and vpc by default allows all the VLANS. Could it be, that the vlan not appeared on the switch and was therefore not upward on the trunk?

• Connection EQL 6110 X (10G SFP +) PowerConnect 6224 10 Uplink ports

  Dear friends,

  Need your help...

  Please let me know if I can connect EQL 6110 X (10 G SFP +) storage to ports 10 G SFP + PC 6224 for iSCSI to my servers on a local network connectivity that is 1 G.

  Correct, do not use the uplink ports for Gigabit Ethernet switch for 10GbE tables.    It can connect, but performance and stability will most likely suffer.   So has been the experience of other customers who have tried to do.

• Uplink port VLAN

  Hello:

  I'm lost

  I know not if you have for example two uplink ports that belong to the same vlan, and two or more NICs for asociated to this VLAN, pinning happen dynamically

  I don't know how to set up a VLAN and assign it to a vNIC

  But I can't found how to link the uplink port to the VLAN in the UCS Manager

  Can someone help me please

  Thanks in advance

  Al

  Al,

  In the end-host mode for ethernet, when you set vlan in the UCSM the vlan is automatically assigning / configured on all uplink and port of the server.

  This is a chapter of the Guide to config:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/UCSM_GUI_Configuration_Guide_2_0_chapter15.html

  However, since version 2.0, there is a feature in which you can control or confiure different VLAN on different uplink ports. This feature is characteristic L2-disjoint and here is a URL to configure:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/UCSM_GUI_Configuration_Guide_2_0_chapter21.html

  I hope this helps!

  . / Afonso

• Uplink Ports Fibre Channel - UCS GUI Configuration Guide

  Hi all

  Could someone please explain which means that what follows in the Configuration of GUI of UCS guide @.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.PDF

  Uplink Ports Fibre Channel

  Manage ports Uplink Fiber Channel FCoE traffic between the interconnection of fabric and the next layer of the

  SAN storage network. All FCoE network-related traffic is pinned to one of these ports.

  By default, the Fibre Channel ports are uplink. However, you can configure them to work as Fibre Channel

  storage ports. This is useful in cases where a Cisco UCS requires a connection to a DAS storage

  Device (DAS).

  My question is, how the FC Port could handle FCoE traffic? My understanding was that FCoE will be lifted and Enthernet connection only.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.PDF

  Thanks for your help

  Concerning

  Vikas Srivastava

  The CF module interconnection fabric is the place where the speration of CF vs. FCoE happen, so it's where the FC frame is extracted in the Ethernet frame.

• The question of the Uplink port speed

  Hi there guys!

  I want to set my 4 GB uplink port speed, but the UCSM show me only 1/10/20/40 GB. How do I change the port speed trought CLI?

  Greetings.

  Here's our UCS 2.0 running and I am able to adjust the speed of uplink FC

  ucsfi-01-A / CF-uplink/fabric/port-channel # show in detail

  Port channel:
  Channel port Id: 255
  Name: ucs-n5k-pc255
  Admin State: enabled
  Oper State: to the top
  Admin speed: Auto
  Oper speed (Gbps): 32

  ucsfi-01-A / CF-uplink/fabric/port-channel # set adminspeed
  1 Gbps 1 Gbps
  2 Gbps 2 Gbps
  4 Gbps 4 Gbps
  8 Gbps 8 Gbps
  Auto Auto

• VSAN membership down on the CF mapped uplink port

  Hello

  Since I upgrade Cisco UCS Manager, all frame and fabric of interconnections of version 2.2 (1), I have a few minor flaws.

  I configure ports 31 and 32 as FC uplink ports and mapped each port to a vsan:

  Port 31 = VSAN 'blue '.

  32 port = "red" VSAN

  (I know, it is not common to map two different VSAN to the same fabric, but I have to)

  Since the update, I get minor flaws:

  31--> FCoE or FC uplink port is broken on 'red' VSAN / membership-down

  32--> FCoE or FC uplink port is broken on 'blue' VSAN / membership-down

  I have no channels of port FC or FC enabled link mode. Interconnection of fabric is EHM.

  Even in other tissues.

  Can anyone help me or is it the same cosmetic problem as stated in the quote?

  FCoE Uplink vsan membership fault for any vsan not configured upstream Symptom:
  
  Fabric Vsan Membership Down fault message on FCoE uplink ports
  Severity: Major
  Code: F1083
  Name: Fabric Vsan Membership Down
  Conditions:
  Observed with UCSM 2.1 and when FCoE uplink port is configured on the Fabric Interconnect
  Workaround:
  None.Error message is cosmetic.
  

  Thanks in advance

  / Danny

  Hello Danny,

  Yes, it is a cosmetic issue in UCSM 2.2.1

  the question is followed by

  https://Tools.Cisco.com/bugsearch/bug/ CSCum89468

  The one that you cited ( CSCud81857 ) is specific to the rising FI FCoE in version 2.1 of UCSM.

  HTH

  Padma

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.