4 SIMS will work on my PACKARD BELL EasyNote TM

Similar Questions

• Packard Bell Easynote laptop computer CD Rom problem in Vista

  I have a Packard Bell Easynote laptop computer and the CD rom does not recognize my DVD - RW drive, it recognizes and plays all other formats, any ideas how to solve this problem?

  Russ

  Hello

  Close all programs and then put in a DVD - RW blank = what happens?

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  CD/DVDs have a tolerance + - and may your reading/reading on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  --------------------

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• FIX: "no mountable boot Volume' on Packard - Bell EasyNote A8

  Hello:

  I want that my recent experience would be helpful to my fellow users.

  My Packard - Bell EasyNote A8, running Windows XP Home, was to have a "Blue screen of death" problem very frustrating showing "One-Mountable boot Volume," at the start of the system, just after loading Windows XP logo, after a recent system total restore factory & all subsequent updates have been made. An extensive internet search was not much help. Physical damage to several sectors on the hard disk are likely, after all, there @ and 10,000 POH

  Solution:

  1. let regenerator HD program work for about 6 weeks continuously. I don't know how this has helped, it detected 100 many bad/damaged areas and repaired only 3. Had to manually stop because he was taking forever. He got stuck on 47118Mb, with @ 3Gb more to go.

  2 restart the computer. Press the magic F11 button.

  3. system restore started. It is automatically detected and repaired the damaged partition. Everything is automatic. Just sit back & relax & follow the prompts on the screen.

  4. my Packard - Bell EasyNote A8 now return works perfectly as it was before the problem started. All updates completed. No "blue screen of death" until now.

  E-mail address is removed from the privacy *.

  Hi M_Rafi,

  Follow the steps in this document to resolve your problem with unmountable boot volume.

• Packard Bell EasyNote ENTG71BM Ram Upgrade

  Hello.

  I got a new packard bell easyNote laptop computer ENTG71BM. This one has 2 GB of ram and windows 8.1 so ram is not enough. Can I remove the backcase and install another 2 GB of ram? Is an empty slot available?

  First remove your image (full S/N and SNID said).

  PB ENTG71BM (8.1 - 64 bit Windows) has the same mothers like the Acer Aspire ES1-512.

  Your laptop supports up to 8 GB - DDR3L - 1600 MHz (1x8Gb).

  1 - the bars of origin are:

• Packard Bell EasyNote SJ51 coprocessor driver is missing

  Hello world

  I've updated this laptop Packard Bell EasyNote SJ51, with native Windows Vista Basic, Windows 7 Ultimate.
  After installation clean smooth found WU driver VGA that apparently has not been incorporated in the W7U so that I had to download synaptic drivers on mine.
  So great that I decided to glorify it with a memory upgrade buying little extra RAM.
  I've used Speccy to search for details and then realized that the temperature is too high. (70/80 ° C)
  Once activated the materiel management tool, I discovered that the coprocessor driver is missing... so I ran windows research pilot of this Panel, the OS invites you to visit the Web site of the manufacturer I did but I couldn't really find anything related to this laptop.
  Even on the site Web of NVIDIA.
  No idea where should I look for him safely?
  Thanks in advance for your help.
  Information on the mobo:
  Motherboard

  Manufacturer PACKARD BELL BV

  Model EasyNote_SJ51 (Socket A)

  Version PB96F104A7

  NVIDIA Chipset provider

  Model of chipset nForce 560

  Chipset revision A2

  Southbridge NVIDIA provider

  Model of Southbridge nForce 560

  Southbridge revision A2

  System of temperature 70 ° c.

  BIOS

  Brand Phoenix Technologies Ltd.

  Version 1.0 H-3221-0010

  Day 12/03/2008

  ICP data

  PCI slot

  Type of PCI slot

  Use of the available slot

  Bus width 32-bit

  PCI Slot 1 slot designation

  Slot number 0

  PCI slot

  Type of PCI slot

  Use of the available slot

  Bus width 32-bit

  PCI Slot 2 slot designation

  Slot number 1
  Details of the CPU
  CENTRAL PROCESSING UNIT

  AMD Turion 64 Mobile TK-57

  Carrots 2

  NET 2

  Name AMD Turion 64 Mobile TK-57

  Codename Tyler

  Package of Socket S1 (638)

  65nm technology

  Specification of the AMD Athlon (TM) 64 X 2 Dual - Core TK-57 processor

  Family F

  Extended family F

  Model 8

  Model expanded to 68

  Stepping 2

  Instructions (+) MMX, 3DNow! (+), SSE, SSE2, SSE3, AMD 64

  Virtualization Supportato, disabled

  Hyperthreading unsupported

  200.3 MHz bus speed

  801,4 MHz rated Bus speed

  Stock of basic speed 1900 MHz

  Stock of 200 MHz Bus speed

  Average temperature of 74 ° C

  Caches

  L1 Data Cache Size 2 x 64 KB

  L1 Instructions Cache Size 2 x 64 KB

  L2 unified Cache Size 2 x 256 KB

  Core 0

  Basic speed 1903,0 MHz

  Multiplier x 9.5

  200.3 MHz bus speed

  801,4 MHz rated Bus speed

  Temperature of 73 ° c.

  Thread 1

  APIC ID 0

  Base 1

  Basic speed 1903,0 MHz

  Multiplier x 9.5

  200.3 MHz bus speed

  801,4 MHz rated Bus speed

  Temperature of 75 ° c.

  Thread 1

  APIC ID 1
  IlConteMascetti

  Hello

  I installed the

  15.23_nforce_winvista32_international_whql

  found on NVidia U.S. and looks that the coprocessor driver was finally installed.

  Greetings

  IlConteMascetti

• Packard bell easynote you 11hc on custom windows 7 activate WiFi even after pressing f3

  Well, it's bad for me because I do a lot on the internet and it started today. And are not sitting well you should try pressing Fn + F3 because that's what I do when I need to use it because my laptop has a weird keyboard and I reinstalled my drivers and still nothing nothing has helped even from support.

  If you haven't already done so, try to run the network troubleshooters (esp "network and Internet" - "Internet connection" and "Network card") to see if they find and fix any problems.

  Have you looked into "Device Manager" (from ) under network adapters, in order to check that the wireless adapter is listed, working correctly and enabled? Right click on the adapter, and then click Properties.

• Packard Bell Easynote TK81 compatible motherboards

  Hi, I need compatible motherboard for Easynote TK81 - PEW96. I burned by the way the videochip and now we cannot find compatible motherboard. CPU is MAD Athlon II P360. Can you tell me MB compatible for this model of videochip? Thank you.

  Here are a few:

  http://www.eBay.com/Sch/i.html?_odkw=&_osacat=1244&_FROM=R40&_trksid=p2045573.M570.L1313&_nkw=Easyno...

• keyboard and mouse on packard bell laptop only work in safe mode

  I have a packard bell easynote laptop running on windows vista, which has fine worked for two years, the other day I went to signon and not all the hits of keyboard have been recognized, after possibly connection and found loading keyboard and a mouse does not respond as completely unusable.

  -Booted safe mode and everything works fine, ran the antivirus and diagnosis-nothing found, still only works in safe mode.

  has run a restore of system-nada, still only works in safe mode

  tried an own help start-up-no, still only works in safe mode

  Please help he kills me!

  Well, I decided to bite the bullet and give it a go, after all, I know very little of these things, however I'd wait until Saturday, when I have the time to focus on it, then the word 'Register' in your response reminded me that I had bought registry cleaner Uniblue several months ago that I ran last night and hey presto problem solved! :), I'll never know if your solution would work but thanks for your help anyway and I hope that you would have had me there.

  Rich

• Problems with factory reset on a Packard Bell

  Hi cox.haley1,

  After a Microsoft update Tuesday May 13 laptop Packard Bell Easynote TK85-GN-051UK of my granddaughter had a huge problem with the start-up that could only be ordered with a Factory Reset. Finally I had all this work and re-installed all software programs. Several days later, after update of Microsoft more, another problem arose that could only be fixed again with a Factory Reset, so I had some things to begin to repair, but it got stuck in the Installation of the software... Install Office 2010...33/45

  18hrs. later he was still stuck there.

  I sent to Packard Bell for re-installing operating system Windows 7 DVD & utilities drivers & Applications DVD... Incl. postage. £37.

  They have not worked as once more stuck in the same place.

  Packard Bell is a Dutch manufacturer and a subsidiary of Acer will help so I don't need to waste money on recovery discs.

  Can anyone suggest something to help please?

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/Windows-cannot-complete-installation-in-safe-mode/5e913a56-B29B-4386-A462-20e1991a1edc#LastReply

  Thank you. All sorted now. There is a corruption of Microsoft Office files. Formatting of hard disk. Re-installed my Windows 7, etc and then all software, updates everything and now all is well again.

• Packard Bell m/c will now fire up to the "home page" - MS system is Windows XP

  Windows xp now will not pull upward on the old Packard Bell computer, then the screen falls in "sleep" mode I have the original Windows XP disks, but does not help. Can I make a record of 'boot' via the net using my second computer?

  Here are the instructions to burn a cd for the disk to boot Hiren that you can then run checkdisk, a memory test and other tools

  Courtesy of Jose Ibarra

  Do you have a Hiren Boot CD, which you can download here:
  
  http://www.hirensbootcd.org/download/

  The ZIP file is large, so the download will take probably a little while to complete the bit it is worth.  Then unzip the download to extract the Hirens.BootCD.ISO file that will be used to create your new bootable CD.

  Create a bootable CD. ISO file is not the same as simply copying the. File ISO onto a blank CD.  You must use software that includes how to burn a. ISO to a CD to create a bootable CD.

  In the file Hiren ZIP are the file BurnToCD.cmd that you can double-click to start, but I've never used and prefer to use ImgBurn.

  If you need a simple and CD burning, this is a free software popular software:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install anything from UniBlue or the Ask Toolbar (never install the ASK toolbar for nothing).

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your new bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.

  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When starting on the Hiren's CD, you will see a menu of options.  Choose Mini XP.  It will appear while Windows is loading and you will be presented with a desktop computer that has the look and feel of the interface of Windows Explorer, you are already accustomed to using.

  A way to check the drive for errors is to open my computer and right-click on your afflicted player and choose Properties, tools, error, check checking now... put a check mark in the boxes and then start.

  Sometimes that works, then you can also click on start, run and in the type box:

  cmd

  Click OK to open a command prompt window and enter the following command (assuming that XP is installed on your C drive)

  CHKDSK c: /r

  This disk check can last a long time (perhaps several to several hours) depending on the size of the volume, the amount of data on the volume and what the disk check finds to do.

  Let chkdsk finish to correct the problems, he could find.

  According to the speed of your system, the size of the volume, the amount of data on the volume and what chkdsk finds to do, he may take a long time for chkdsk with error correction to complete (several hours) or it may seem to be 'stuck '.  Be patient.  If the HARD drive led blinks always, chkdsk is something to not interrupt him.  It finally end one way or the other.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You may need to run Chkdsk c:/r more than once.

• Packard Bell M3671: New installation will not leave my upgrade or install updates

  Hello

  My mother has a Packard Bell M3871. Recently, she had a problem she turn on the computer and the date would go to 01/01/2011 and not all startup applications start as the antivirus, etc. I decided to restore the system to factory settings. Worked well. The day following the date returned in 2011 and I was not able to use internet as he said the connection is not private and it was recommended to install updates. So I waited a few hours while he was looking for updates and without success. Continues the search now and find nothing. I even tried the upgrade to windows 10 but the GET installation stuck at 99% and after a manual reboot as usual, loads of windows 7.

  Any help is much appreciated!

  Hello:

  See if these two updates of W7 installed solves the problem.

  https://support.Microsoft.com/en-us/KB/3083710

  https://support.Microsoft.com/en-us/KB/3102810

  You can also read this article for more info...

  http://www.ZDNet.com/article/sticking-with-Windows-7-the-forecast-calls-for-pain/

• Does anyone know if the Sims 2 (and EPs) will work on Windows Vista 64-bit?

  I was hoping to get a new computer, this weekend, but before I can, I need to make sure that everything will work actually on this subject. Microsoft says that the Sims 2 works on version 32 bit Vista, but all new computers come with the 64-bit version. So, anyone know?

  Thank you very much to all those who can help you!

  -J' ticked the boxes of the EPs and EPs are two that do not work with Vista University and open for business, but I'm not running the game through them being the most recent EP I apartment living. And, since AL works with Vista, the full game and all former EPs should work, right?

  Hi, Julia:

  While searching the http://www.bing.com results, it seems that many people have reported that the game is compatible with both 32 - and 64-bit Vista machines.

  I hope this helps!

  Justin

• Just upgraded to Vista Home Premium to XP. Got a Packard Bell with RF for the Media Center remote control, worked fine with XP, but is no longer compatible with Vista.

  after update to XP media center units Vista remote control

  Just upgraded to Vista Home Premium to XP.  Got a Packard Bell with RF for the Media Center remote control, worked fine with XP, but is no longer compatible with Vista.  I checked the usb driver for the usb XF-10 rf remote receiver and it is fine, uninstalled and reinstalled it.  Handset was working fine a few days ago.  I also went in 'Administrator', 'services' and then active HID, but it still does not work.  Media works well, but it would be nice to have the operation of the remote control!  Not particularly computer, simply suggestions please!  Thank you, Nick.

  Hi Nicolas,

  I suggest you to check the battery. Additionally, make sure that you have installed the right drivers for you Consumer IR Port.

  For more information, you can check the link below,

  http://www.PackardBell.com/index.html

• Touch Packard Bell portal has stopped working.

  Original title: packard bell touchportal

  Touch Packard Bell portal has stopped working. Can someone please help?

  Hi RayHC,

  1. what exactly is the problem you face?

  2. when exactly you receive the error message?

  3. have you made a recent software or hardware changes to the system?

  Method 1:

  If you are using the Packard bell computer, you can consult the site Web of Packard bell and try to install the latest version of the drivers for Touchpad and other devices.

  http://www.PackardBell.com/support/?i=spec_videocard_geforce9500gs512&PPN=PB80X27502

  Method 2:

  You can also perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: Make sure that you put the computer to a Normal startup once you have completed troubleshooting.

• Can Win XP Pro on the Packard Bell System evolve?

  HY. I USE a PACKARD BELL INTEL (R) PENTIUM (R) DUAL CPU * address email is removed from private life * 2.00 GB of ram AND I want TO DO AN UPGRADE. CAN I DO IT? IF SO, HOW? I HAVE WIN XP PRO. SP 3... !

  You plan to upgrade to Vista or Windows 7.

  If the answer is Vista, and then you perform an upgrade on the spot, that will keep all your applications and data intack. Note the bare minimum of RAM/memory you need for Vista is 2 GB and it runs slower than XP.

  If the answer is Windows 7, then your only choice is a "custom" / Clean install which means that you must back up all your data file (on external support) and then once the upgrade is complete and then install applications. ". Memory required for Windows 7 are 1 GB for 32-Bit OS or 2 GB for the 64-bit operating system.

  You must run the compatabily Windows 7 checker before doing anything: Windows 7 Compatibility Checker
  http://www.Microsoft.com/Windows/compatibility/en-us/default.aspx

  Windows 7 Upgrade Advisor
  http://www.Microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=1b544e90-7659-4BD9-9e51-2497c146af15

  Windows XP to Windows 7 Migration Guide
  http://TechNet.Microsoft.com/en-us/Windows/ee150430.aspx

  Here are answers to some common questions about the 32-bit versions and 64-bit Windows.
  http://www.Microsoft.com/Windows/Windows-7/compare/32-bit-64-bit-FAQ.aspx

  Also: Check Windows 7 device drivers available for your make and model. If there is no drivers then chances are one or more device (LAN, sound, Etc.) may not work.

  As always, make a backup of the Image of your external hard drive USB driver before you start the actual upgrade.

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.