75 laptops using 2 point access (cisco 1130)

Similar Questions

• A WRT160N V3 can be used as wireless access point.

  I have an AT & T's broadband router.  A WRT160N is connected, so I now have Wireless N capabilities.  I have a second WRT160N I want to put in my living room as a point of access, so I can connect my BluRay player and video stream.  How can I configure the second WRT160N as access point?

  Thank you in advance,

  Andrew

  Topic 1. Yes, you can use your second WRT and put in place as a second access point to your network. First of all, unplug the second WRT to your network and wire a computer in one of its LAN ports. Open the web interface at http://192.168.1.1/ on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.1.2 and disable the DHCP server. Save the settings. Unplug the computer and connect the cable to the first router on one of the second router's LAN ports. Do not use the internet port of the second router! Now you can use the wireless access point in the second router as access point additional for your network.

  For a wireless roaming the two Wrds with identical wireless settings (SSID, wireless security, etc.) and don't forget to enable the SSID broadcast. Only the channel assignments should be different. Different channels spaced at least 5 avoids duplication of canals. Now your laptop can connect to your network via either WRT and internet through the first WRT. It must also be able to move between the two Wrds without losing the connection.

  Re 2. Because the WRT160N has only the ethernet 10/100 ports a CAT5e cable should do. Of course, you can consider getting a better cable, for example a cat6 for future enhancements to your network. It depends on how much effort it is necessary to replace the cable later if you decide to go for gigabit ethernet on your local network.

• AC1900-Nighthawk WiFi Range Extender can be wired in and used as an access point?

  I want to replace my WN802T which is connected to the network.

  Found the manual and it can be used as an access point.

• I have windows vista business edition is installed on the desktop and Vista home edition on my laptop I can't access files on the laptop and vice versa, I am using a d-link adsl router can u help me solve the issues___Thanks__Peter

  I have windows vista business edition is installed on the desktop and Vista home edition on my laptop I can't access files on the laptop and vice versa, I am using a d-link adsl router can u help me solve problems

  Thank you
  Peter

  Hello

  The easiest way is with a crossover cable - a special wire to connect the two systems.
  You can get one at your local computer store - they are not expensive.

  Also check with the site of the manufacturer of your router, because they will have in-depth details on how to
  set up the network.

  ====================================

  Or you can set up a wired or wireless network.

  Setting up a network home
  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network

  Home network, wireless network and computer networking Made Easy
  http://www.home-network-help.com/

  Windows Vista tip: How to install and connect to a wireless network
  http://www.watchingthenet.com/Windows-Vista-tip-how-to-Setup-and-connect-to-a-wireless-network.html

  Ad-hoc networking
  http://windowshelp.Microsoft.com/Windows/en-us/help/0e158c21-4C70-4235-879d-0c9133218e561033.mspx
  Set up a computer-to-computer (ad hoc) network
  http://windowshelp.Microsoft.com/Windows/en-us/help/293c504f-b944-4d5d-835c-f080129bd5dc1033.mspx

  How to set up an Ad Hoc wireless network in Windows Vista
  http://www.home-network-help.com/ad-hoc-wireless.html

  Create an ad hoc WiFi network secure on Windows Vista
  http://www.Intel.com/support/wireless/WLAN/sb/CS-025386.htm

  Networking tutorial home
  http://www.tehnomagazin.com/computer/home-networking-tutorial.htm
  Practically networked - everything you could possibly want to know.
  http://www.practicallynetworked.com/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• The AG Cisco 1130 - disable Radio FastEthernet

  Hello

  I was looking through a 1130AG trying to stop radio stations for a day to test. I acceded to these via the web browser. I disabled the A and B/G radios since the location and then went to another location and disabled the FastEthernet (wired) connection. I want to back up these radio and now I can't access the web interface because I disabled the wireless connection. Can anyone help please get out and direct me where to go next door to activate the radios on the access point (without reset if all goes well) and without the ability to access through the web interface based on?

  Thanks a lot for your help

  Hi Dayne, you are welcome to my friend! ... Sorry for the spelling mistakes before your name (cannot read or type sometimes :)

  Here is some info for the use of Hyperterminal Console connections

  Info from the console;

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15frst.html#wp1034762

  Cisco IOS command modes

  The Cisco IOS user interface is divided into several different modes. The commands available depend on which mode you are currently in. Enter a question mark (?) at the system prompt to get a list of commands available for each command mode.

  When you start a session on the access point, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands is controls spot, such as show commands, which show the current status of the configuration, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the access point reboots.

  To have access to all commands, you must enter privileged mode. Normally, you must enter a password to enter privileged mode. In this mode, you must enter privileged EXEC mode before you can enter global configuration mode.

  Using the configuration modes (global, interface and line), you can make changes to the running configuration. If you save the configuration, these commands are stored and used when the access point reboots. To access the various configuration modes, you must start in global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15cli.html

  I hope this helps!

  Rob

• I try to enable Microsoft XP on a laptop and can't access the Internet to activate.

  I try to enable Microsoft XP on a laptop and can't access the Internet to activate. I have 8 sets of code available, but the phone activation computer said that the codes were not recorded. I need to save this software to get this laptop for my daughter. I can't download and upload diagnostics using my computer. All I get is the splash screen, click the user, and then it will activate the windows screen. When I can't activate online, it suits me and turns off. What else is there to say?

  Of course, you can get online with something :)

  Download the tool on your current computer and transfer it to the affected - save the output in a Notepad TXT file and copy to your functional PC, and then copy the ocntent you your answer.

• Unable to connect to a Sony DV from my laptop using the firewire port after the installation of updates

  Original title: connection for Vista FireWire camcorder problem

  I used to be able to connect my Sony DV camcorder to my laptop using the FireWire on the camcorder and laptop.   Once it is connected the Movie Maker detect my camcorder and automatically transfer the video.  However, since I've updated my computer laptop July 13, 2012, my laptop does not recognize not the camcorder.  I checked my computer and your camcorder is not yet listed.  I checked the latest updates for the driver of the firewire port 1394 and is the day the device is functioning properly.  Can anyone throw any light on this.  The only thing I can think is that since the update, he may have done something for the connection.

  Hi Scarlett,

  Thanks for the post. I'm sorry to hear that the Sony DV camcorder is not detected.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.
  To help you suggest several steps to solve the problem, I would appreciate it if you could answer the following questions:

  1. What is the model number of the Sony DV camcorder?
  2. you receive an error code or message?

  3 update do you have installed?

  See the Windows updates are installed:

  http://Windows.Microsoft.com/en-us/Windows-Vista/see-which-Windows-updates-are-installed

  Please follow the methods and mark the question below:

  Method 1:

  First of all, let us check the status of the FireWire port in Manager devices to do this, follow the steps below:

  Check the status of the port in FireWire devices Manager

  a. Click Start, in the search box type Device Manager and press to enter.
  b. If you don't see the FireWire controller (probably listed under "IEEE 1394 Bus host controllers") in the list, then it is not correctly installed.
  c. If you see a yellow exclamation point, then you must install the drivers, who are usually on a CD that comes with the FireWire card with the camcorder.

  Method 2:

  Step 1:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Step 2:

  A device driver is not installed or a hardware device does not work correctly after you install a Service Pack in Windows Vista:

  http://support.Microsoft.com/kb/948187

  Method 3:

  Connecting i.Link® (IEEE 1394) of the camcorder is not recognized by the computer.

  http://www.KB.Sony.com/selfservice/viewContent.do?externalId=C86798&sliceId=1&MDL

  For more information, see the link below:

  Import analog video to your computer by using a DV camera:
  http://Windows.Microsoft.com/en-us/Windows-Vista/import-analog-video-to-your-computer-by-using-a-DV-camera

  Import video from a videotape:
  http://Windows.Microsoft.com/en-us/Windows-Vista/import-video-from-a-videotape

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• How can I update the BIOS on my Sony Vaio laptop using disc or usb? Note: I can't windows at all.

  Hi, I want to know how can I update the current bios on my sony laptop using the disc or usb.

  I can't access the windows on the laptop at all, because I'm getting STOP: 0 x 00000 "a5 error that says: your bios is not fully compatible with acpi.»
  This error prevents me to access any live disc or recovery disks.
  I would like to learn more about records tho method.
  Thank you.

  Take it to a repair shop, you have damaged the card mother/connections

• I want to use Outlook Web Access for Mac, I don't want to use the light version, I want the full version, but you can't push off the mark. I have firefox 3.6.10

  I want to use Outlook Web Access for Mac (snow leopard 10.6.8), I don't want to use the light version, I want the full version but I can't push off the mark on the light version. I have firefox 3.6.10

  (1) you must update at least Firefox 3.6.24 because there are questions of SECURITY of KNOWN MANY with the version you are using.

  (2) the light version is required on non - IE browsers, except if you are running Exchange Server 2010. With Exchange 2010 they added support for multiple browsers run in the version "no light".

• Is it possible to connect my Mac mini to my Mac Pro laptop using the memory on my mac mini for installing software Ableton as I don't have 3 GB available on my Mac Pro.

  Is it possible to connect my Mac mini to my Mac Pro laptop using the memory on my mac mini for installing software Ableton as I don't have 3 GB available on my Mac Pro.

  I want to download Ableton software, but it requires 3 GB of free memory that I have available on my MacPro laptop not because most of it is used for my library of music because I'm a DJ.

  I'm not sure how I can do it or not at all.

  Thank you very much.

  1. a Mac Pro is not a laptop. Its a big desktop computer.  You probably have a MacBook Pro, which is a laptop.

  2. No, you cannot share the memory (live RAM) or storage (disk space, which is not memory) like that between computers.

  However, it is very very bad practice to have so little storage space available for your computer.   If you have less than 3 GB, you should seriously consider an external drive. and unload some files on the outside. Its best not to leave your hard drive to go below 10 GB of free space because it can seriously affect your computer's performance.

• while shooting pool on directory, use the pointer to draw the ball, that the screen goes up and down

  When I use the pointer that the screen moves up and down I want to trun off

  Hello ron crabtree,.

  This thread has been created in the Feedback forum. the Microsoft moderation team has moved this thread to the Performance and maintenance Forum.

• Is it possible to use a Linksys by Cisco Wireless - G Internet home monitoring camera with Labview

  I was wondering if it is possible to use a "Linksys by Cisco Wireless - G Internet home monitoring Camera" with Labview

  http://www.dabs.com/ProductView.aspx?quicklinx=53PX&SearchType=1&searchTerms=network+cameras&PageMod...

  I wan't to be able to get the raw data from the camera and analyze it.

  I found a simple soloution to this problem,

  Is possible to use a web browsers invoke node basically give a screenshot of the web page (get image)

  It can then be loaded into a display of the image and will show exactly what the web browser is showing and can also be analised by unflattening the pixmap.

  Maybe it's not the most effective method, but he turns my rig fast enough and does the job

  It may also be a setting value of the display of the photo to "smooth updates" that gets rid flashes white as the changes to the image, if anyone else has this problem.

• How to adjust the scale of a chart using reference points?

  Hello

  I'm working on little code to display data from a spectrometer.  I've got to the point of producing a graphic intensity vs energy, but I'm having some trouble of calibration of the x-axis (energy).

  The customer wants to be able to insert filters with a cutoff of known energy and use those points to determine which positions on the graph correspond to what energies.  In terms of programming, I need to let the user click on the graph at two points with known values and use these points to recalculate the XScale multiplier and offset (I think).

  I tried a few different things and attached by the best attempt so far.  This is a simplified example, but I hope it picks up enough problems to be useful.  I can't help thinking there must be an easier way to do it.  Any suggestions?

  What you have done is good. The only thing that I would have a little problem is that there is no visual feedback on the graph for the user. You can also do this with the sliders. Let them drag the sliders on two points. It is more Visual, and you can see where you have selected. I'm not sure that it will be much easier than what you've done. You could also use a hybrid of the two methods and have the cursor to move until you have selected.

• How to install XP on a laptop used, have CD/DVD but no product code

  I bought a laptop used on three or four years with a genuine version of XP Professional already installed. I have the XP disc with me (has "for refurbished PCs ' printed on it), however I do not have the product code with me when I moved to Southeast Asia. The laptop broke down so I will soon buy another used quality XP laptop.

  Is it possible to install XP on it without the product code?

  If so, is it possible to activate it without a phone call? I have a quad-band GSM, but the voice quality is very poor with calls long distance.

  Thank you

  No product key, no activation.

• How can you connect a printer to a laptop without cd-rom access Tablet

  How can I connect Canon MX472 printer for a Tablet laptop without cd-rom access?

  You can download all the software here:

  http://www.USA.Canon.com/Cusa/support/consumer/printers_multifunction/pixma_mx_series/pixma_mx472#Dr...