950 cartridge save & reinstall?

Similar Questions

• Problem - has ink cartridge but no printing appears on the paper

  I have a printer of HP Deskjet 4200 all-in-one with a relatively new ink cartridge.  The printer prints white - nothing appears on my paper.  The last time I used the printer (with the same cartridges) was four months ago, and he was fine.  To my knowledge, nothing has changed (parameters, etc.).  I can't figure out how to get the printer to print anything.  I could go out and buy new cartridges, but ones I have is barely used, although only around the age of 6 months.  And the problem seems to be both color and black print (printer has two cartridges) - so I made me think that it would not be a cartridge problem.  Any suggestions on what I might try?  Thank you.

  It is possible that the print heads have become clogged due to sitting for so long unused.  Try to run the three cycles of cleaning of the Toolbox.  If it does not recover the printhead, then place 1 "of very hot water in a cup and watch the nozzles of cartridge in hot water for about five minutes.  When it comes gently dry the printhead on a wet cloth dry contacts of the cartridge, then reinstall the cartridges in the printer, and try another cleaning cycle.

• HP Officejet 6835: Not to recognize new printer cartridges.

  Exchanged a defective HP Officejet Pro 6835 at Costco. I kept the old cartridges and Costco pulled the new printer cartridges and kept them. During the installation of the printer does not recognize the used cartridges. Error message received to use cartridges supplied with the printer configuration. Did not have them. Is gone to town & bought new HP cartridges and install. The printer took over in the same place on the installer. It does not recognize the new cartridges. What can I do? I can't start the installation program. I remove the new cartridges and reinstall them using and get the same message again. She can't get to work, so I'll have to make another 90 mile round trip to Costco to replace this printer.  Any suggestions?

  Doreen

  You will need to install cartridges for initial configuration, Costco shouldn't have removed the cartridges setup.  You can contact HP, they could send replacement cartridges setup or they may suggest that you only contact Costco.

  From a post of Sunshyn2005, contact technical support HP see the following link to create yourself a file number, then call and it can help to expedite the appeal process:

  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  
  File number and phone number appear, this allows to contact HP.

• HP 5940 - color cartridge status light flashes with new HP 97 cartridge

  Just installed a new HP 97 cartridge and the light flashing color cartridge status. Put in old 95 HP cartridge and the lights are out, but this cartridge is empty. I have cleaned all connectors (inside the printer and the cartridge), tried reinstalling several times. Any ideas or am I stuck with a bad cartridge? The only difference I see between the cartridges, it is that the 97 is a greater variation of the 95. Thanks for any help.

  Never forget, faulty cartridge. He took over and replaced it, it works now.

• Reference Dell v305 problem black cartridge not aligned

  my printer dell 305 said all of a sudden the black cartridge is not aligned properly (otherwise it is said to remove the Strip). If I take the cartridge and reinsert it, I get the same message. If my printer is broken or do I have to just buy a new cartridge?

  scs822,

  Do you use Dell Series 9 ink cartridges?

  If you unplug the printer from the wall and remove the brick of power for 60 seconds, this will reset the error messages that the printer. I would then plug everything back in.

  Turn on the printer.

  Open the printer (power on) and remove the Dell Series 9 black cartridge and then reinstall it. I then remove the Dell Series 9 color cartridge and reinstall it. Now, close the printer, and it will print an alignment page.

  Error messages?

  Print Cartridge black = Black (left) cartridge = color (right side)

  photo cartridge = cartridge black (left side) = color (right side)

  Dell Series 9 ink cartridges have a sensor to them that cannot be reset. Article on Dell ink cartridges filling.

  Dell Series 9 ink cartridges can be purchased at Staples, Wal-Mart or any Dell website.

  It is possible to get an ink cartridge Dell Series 9 with a bad sensor. I would take these to the place of purchase for a replacement.

  Rick

• Missing or damaged cartridges message

  I just replaced my black cartridge with a new hp cartridge in my photosmart all-in-one printer 7520, but get a message that "one or more cartridges are missing or damaged.  Seems to be the black which is the cause of the problem.  Now what?

  Try following the steps in the link below, as clean the contacts of the cartridge and reinstall it

  http://support.HP.com/us-en/document/c03379185

  That solve it? If not, is the cartridge still under warranty? [there should be an end date of guarantee written on the body of the cell.

• Printer says I have ink cartridges in the wrong housing but they are not

  I have a printer HP Photosmart 7510 who keeps saying that I have the cartridge in the wrong slot. All 5 are in the correct locations.

  Take a look on the link following which treats problems ink cartridge.  Click here  You did most of these, but do not yet made steps.  The link suggests you clean the contacts again.  Make sure that the cartridges are level with each other.

  If this does not help, I suggest you do a reset of the ink system.  To do this, remove the printhead and ink cartridges.  See this link.  Close the access of transport cover.  Follow the reset instructions in the following link.  Click here  Once the printer rear lights up and indicates that the print head is missing, reinstall the print head.  Close the access door.  When the printer indicates one or more of the ink cartridges are missing, reposition one of them and close the access door until the cartridge shows.  Repeat the process until all the cartridges are reinstalled.  This aid?

• HP Photosmart 3310: Using only the black cartridge

  Suffice it for the most part to print text in black, but it seems to exhaust all my color at a speed that is ridiculous and expensive cartridges.  How can I use the black cartridge only?  I use an iMac and iPad (for remote printing)

  Hi @Cambridge29,

  I see that you would like to know how to print with just the black cartridge, save the color for color printing cartridges.
  I would like to help.

  I understand your frustration, I don't really. However, this printer uses same color inks when printing in black only. If run out you of color and kept black printing only, you provoquerez problems with the print head. It is the the user guide for your printer, refer to page 148. Series of all-in-one Photosmart HP 3300

  You can have a setting in the print driver to print in grayscale, which uses fewer colors.

  Application, go to file, print to display the print screen. Here is a screenshot where to access the settings of the print screen driver. Then you can save the setting as a preset.

  

  What operating system do you use? Mac OS X: how to find which Mac OS X Version is on my computer?

  If there is anything else I can help you, let me know.

  Good day!
  Thank you.

• HP 60XL black ink cartridge: bad ink

  Hello, no problem with the impression that a few days ago.  Ink quality is poor.  Have aligned, cleaned the printheads, go to the page "print and scan the doctor"... both black and color cartridges are about 90% full.

  Is it possible to remove the cartridge and reinstall it?

  My printer is a HP Photosmart... D110A all-in-one... bought in February 2011.  Works very well.

  Thank you.

  Hi @gator74,

  Welcome to the Forums of HP Support!

  I see that your HP Photosmart Wireless all-in - One Printer, prints in poor print quality. I would be glad to help and don't forget to come back to this thread and check "Accept as Solution" if I helped successfully will solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that you were part of the troubleshooting already. Looks like you have dirty/defective ink cartridges or there is a problem with the distribution of ink system.

  Please use this guide to try to resolve the problem:

  • The problems of print quality for the printer series HP Photosmart e-All-in-One (D110a and D110b)

  If the problem persists and the cartridge is no longer under warranty, you can try the solution proposed in this video. Please use are at your own discretion.

  Video: 7 ways to clean blocked clogged ink cartridges

• HP envy printer cartridge

  I recently bought my printer HP Envy 5530 third.  After going through the process and allignment installation processs, I printed the test page and also a word document.  The result was of lines are ignored, and half of the line was printed.  I took the cartridges and reinstalled them.  the same problem.  I went to the HP site and run the diagnostic program.  the same problem.  I also used the HP on the online service request form.  Two weeks have gone by - NO RESPONSE.  I finally took one of my other printers cartridges.  IT WORKED.  I put "defective" cartridges in the printer prior.  Did not work.

  How can I get replacement cartrideges?

  Hello

  Please call the technical support team on: 6836-474-1800 to replace the ink cartridge.

  Give Kudos to say 'Thank you' by clicking the 'PLoP icon '.

  Click on 'Accept as Solution' if it has solved your problem, while others may find it.
  Although I am an employee of HP, I speak for myself and not for HP.

• Officejet Pro 8500 A909a print cartridge jam

  I removed the filter switch and the 2nd optional drawer.  I can't find any sign of a paper jam.  The print cartridge is stuck on the right side and I can't reach in this place.  There is what appears to be a hatch above where it is blocked, but I can't open door - I fear I'll break it.  The printer is barely a year - of ideas?

  Yes, I did all this.  I was finally able to reach in and find a part to seize the cartridge and on top.  Still can't get off the cover - looks like it is supposed to just swipe, but it wouldn't be fair.  Anyway, once I manually moved the cartridge, I reinstalled the cartridges.  Seems to be ok now.  Thank you.

• New D5160 ink cartridges will not work

  My printer photosmart D5160 HP need of ink so I bought the black (98) and three color (95) and install. They have not been rewarded. I used the tool kit to see if the ink levels are detected and no cartridge is detected. Red Exclaimation of printer lite flashes. I have several times gone out cartridges, cleaned the contacts and install. I turned off the printer, waited 10-15 minutes and turned it back. Still nothing. I had this problem 2 years when I replaced the cartridges but ultimately the printer detects them. I have a problem with the cartridges I bought or is it the printert? Everything was good with printing until I became a faded print copy and decided to change the cartridge. No error message, no flashing lites. As soon as I removed the old cartridge and reinstalled - it's at the beginning of this flashing red exclaimation lite.

  I am running Windows XP HD on a Toshiba laptop. I hope I have provided enough information for someone who could help me.

  I got a solution to my problem thanks to Advanced Tech Support with HP. Did you know that the printers are defined at the regional level? Yes, indeed. USA is region 1 and region 2 is Europe. It is defined by the settings of the software. HP has kindly give me the region codes to reset my printer to region 1 USA bought German so he will accept cartridges USA version. Perhaps in the future these regions will disappear and the world community, that we all will be Preval? In any case, Bravo to the team Advanced Support HP that has therefore reactivated me.

• HP Officejet Pro e-all-in-8610: HP Officejet Pro 8610 - error Code: "0xc19a0013" (printhead missing or failed)

  I bought the printer (e-all-in-one printer HP Officejet Pro 8610) in January 2015.  The printer was working properly - fax, copy and scan, until two days ago.  Now, it doesn't print at all.  Received an error code: "0xc19a0013" (missing or does not have the print head).  An expanded version of the error code reads: "the print head seems to be missing, not detected, or incorrectly installed.  Error: 0xc19a0013.   The printer uses a removable printhead, HP Ink cartridges (black) 950 and 951 (cmy).  I used the diagnosis of HP support recommendations: all software and firmware for this printer is installed. HP ink cartridges are not low or empty; remove the printhead ink cartridges and reinstall them.

  There are several steps in the recommendation of troubleshooting, but I stopped to lift the printhead.  Because of my technical inexperience, and there were too many ceveats (attention, attention, proper relocation and etc..)  with the removal of the print head which could cause problems more serious.  Then, I stopped to remove and clean the print head.  Also, used the doctor to Scan printer HP for assistance. Tool to clean the printhead does not.   What worries me most with the 0xc19a0013 error code is his explanation: the print head seems to be missing, not detected, or incorrectly installed.  I can use all the help I can get to understand what is happening with the error code that I received and the resolution of the printer malfunction.

  Contact HP technical support at the 800-474-6836 for more options.

  If you do not live in the United States / Canada region, please click the link below to get help from your region number.
  Language-country selector.

• printer Deskjet 2540: lost password

  Hi am new Android phone and Tablet also lost all the information (I forgot to save) reinstalled HP ePrint. AL in one company to distance and ePrint

  Which none are for letting me print saying no printer found internet or not no password

  Unfortunately I don't remember the password any help would be appreciated as not good with technology

  Thank you

  Sharon

  You might want to try to set your printer to the factory settings that should erase the passwords can be added when you configure applications. I'll look in a specific way to do for your printer, but in the meantime try what works for my all in one printer scanner.
  Turn on the printer.
  turn it off by unplugging the power adapter, wait a minute.
  If it has a keyboard, press and hold the # and 3 buttons while plugging the adapter back in. Keep and hold keys until the printer reboots.
  
  See if you can print from your Tablet after the reset.
  Sometimes simply unplug the printer for a few minutes will reset things.

• MacBook Air (13 inches) early 2014 restart itself

  I had this problem where my Macbook Air randomly restarts by itself. Sometimes he just locks (goes to the password screen) even if it is used.

  I took it to Geek Squad since I bought this computer at Best Buy, they've had for a week and all I've heard from them is that there is no hardware problem, and that the computer is "optimized" and upgraded. Continues a day after, because I am a broke student, I can't afford to carry anyone at this point and I don't have any form of insurance or guarantee. I tried to reset the SMC, reset NVRAM, open disk utility and repair the disk, reset preferences to default power saver, reinstall OS X about 4 times in the last 4 months trying to get this resolved. If anyone has any suggestions, it would be greatly appreciated.

  Not enough information on your mac. You can download etrecheck from http://www.etrecheck.com/

  then run it, it produces a list (without personal data), copy it to the Clipboard (share button) and post it here.

  Who can help us to find a cause for the issue.

  Lex