A99 problems, needs an Urgent Firmware update!

Similar Questions

• WRT54G2 problem appears after the firmware update

  Hi everyone, a newbie here. Nice to meet you all and thank you in advance for your help.

  Here's my problem. I have updated the firmware on my router for 1.0.04)is Sunday, and then there are problems on my router.

  1 have a weaker signal.

  2. the router cannot detect my internet just as it has been in the past. I have to type in my PPPoE setting for example my user name and password in 192.168.1.1. Furthermore, I use AT & T DSL.

  3. my internet will totally drop off after several hours. I have to reopen it and the modem power on & off switch.

  So I want to know if I can downgrade the firmware back to 1.0.01 or is there any other setting that may help me get but it? A list of steps is better.

  Thanks again in advance and have a nice day.

  If you haven't already done so, try to do a hard reset, hold reset button of the router for at least 30 seconds with the power connected to the router, and then reconfigure as needed.

  Since I use your & AT T DSL, you can reconfigure the DSL modem, so it don't the PPPoE connection and then reconfigure Type Automatic Configuration - DHCP Internet connection router.

  There is another question that may arise with an AT & T DSL modem. My Speedstream 4100 & AT T DSL modem put the IP address 192.168.1.1 for the router WAN/Internet port. If the router is configured to the default settings, there will be a conflict between the modem and the router and none of router devices connected will be able to access the internet. The solution is to change the IP Address of the router to the router on 192.168. 2.1. Restart all router connected devices after you have made this correction.

  Also with some model WRT54G2 (happens on my router WRT54G2 V1) the wireless signal will go offline when a wired computer is started. When this happens, the work around is the power cycle that the router once the wired computer has started, or log in to the router, go to basic wireless settings page and click on the button Save the settings. Then the wireless signal comes back to the top and wireless devices will resume their connection.

• Autoruns.exe serious problem, need help urgent please

  Hi, someone there is familiar with this software from sysinternals? Have accidentally disabled key drivers in my laptop with this software and cannot run again. Anyone know how to reverse the errors using this application? Posted full problem in the recovery and repair forum. Have had no response from sys internals forum and really need help. Thank you, Jay

  Try to reactivate the drivers tab drivers doesn't work, so did system restore. Thanks to all who responded, the problem is solved

• 32TL933 - in places of Toshiba Youtube app not working after firmware update

  I started having a problem since the latest firmware update on my 32TL933.

  Everything worked fine until the latest firmware update.
  Since then, when I connect to Toshiba Places, everything works well except Youtube.
  When I try to access Youtube, it shows the Youtube Logo and stuck on it...

  I would appreciate if someone tell me how can I solve this problem. YouTube are the only thing that I used in places of Toshiba, and now, I can't, it's frustrating cause I have this TV since August!

  Have you tried remove the Youtube app, and then add it again?
  Try this!

• Photosmart pro B9180 firmware update problem

  Hello

  I have a problem to update the firmware on my HP photosmart pro B9180.

  The firmware on it is very old, 20070426.

  I m running on a Mac, OS X 10.9

  When I tried to start updating the firmware with the firmware update it got stuck after pressing 'continue' on the license agreement page. Through various positions, I found that I had to install the version 10.5 of the HP driver software to work around this problem. I ve done this and of course, he started the next step, "detect devices. The result is that he finds no demanding devices updated firmware that I find hard to believe since it s of 2007. The printer is on the network and I can normally access.

  I now have it connected via USB to try another approach. The result is that the phase of "sensors" the update of the firmware ends unexpectedly leaving me with the ability to report it to apple or reopen the update of the firmware.

  I ve also tried to use HP Device Manager to check the software updates. This property returns "server is not available. "Please try again later".  Tried for the last two days, but the results are the same.

  Any help or pointers is appreciated. If need more information please ask

  Jan

  Hi @Rohdekill

  May I ask why you try to get an update of the firmware? I know you said feel you yours is outdated, but I want to say are you a program that allows you to search for an firmware update pushed?

  From what I see, there is no updated firmware for this printer. There are updates driver for Mac and the Windows operating system, but no update firmware.

  If you have a problem, I'd be happy to help you.

• Firmware update recent Airport 7.6.7 causing problems with VoIP

  Hi all

  Firmware update of recent Airport 7.6.7 causing problems with VoIP.

  Unable to connect voip since update...

  Any help appreciated.

  Thank you

  It might be useful to know what VoIP that you use and what type of problem the update affects your VoIP.

  My MagicJack & NetTalk lines properly.

  Jim

• UJ - 831S - firmware update problem

  I am with a problem updating firmware V1.02 for ' DVD-RAM MATA * a UJ - 831S ", according to press [OK] appears the message"THE TARGET DISK no IS NOT PRESENT", as to decide?

  Hello

  Why did you do any firmware update?
  As far as I know the reader uses the Win operating system drivers.
  Also if you have problems with the drive, you must remove the drive from Device Manager. After the restart of the operating system should recognize the drive again.

  Good bye

• 900 Elitepad F.50 (SP68375) G1 firmware update and defect TPM, Bitlocker problem

  I recently installed the firmware recommended for ElitePad 900 G1 (sp68375.exe) running Windows 8.1 update 1

  System BIOS Update F.50 for HP ElitePad 900 G1 Tablet (c04409743)

  In order to install the update I had to suspend bitlocker drive encryption, which is a mandatory requirement in my workplace.

  After properly installing the update of the firmware and trying to catch the bitlocker encryption, Windows reports the following error:

  "BitLocker Drive Encryption error."

  Wizard initialization has failed.

  The BIOS does not correctly contacted the

  Trusted Platform Module (TPM). Contact the

  the computer manufacturer for BIOS upgrade instructions"

  I tried to re-download and reinstall the firmware update, but ended up with the same error after successfully update a second time.

  Someone else (or HP) applied this update firmware and can fix any counselor or a workaround to get BitLocker up and run again? My ElitePad is now reported as non-compliant system due to the suspension of BitLocker.

  Thank you.

  Please try latest BIOS on HP.com (F.52) for the Elitepad 900.  If it solves your problem, please check the issue as resolved.

• Firmware update problem

  I have a sansa fuze 4 GB which I bought two years ago

  Everything was fine except with the number of files you have in the root folder of music

  A few days ago, I noticed that there is a firmware update available...

  so I did the update (now I v02.03.33F) and I have a serious problem:

  The sound is too low

  is there any solution for this?

  THX

  thx for the quick reply

  I just changed the drive to the North America region and... everything is fine

  thx again!

• Firmware Updater problems :(

  I just download the Sansa firmware update, and when I go to run it, an error message appears saying "the Installation failed. Please try again later. "I started again and received the same error message. Then I waited about 30 min. and sure enough, same error message. What I'm doing wrong!

  OK, the fact is that 90% of us who have been here very long you will simply ignore the update. On the "rocket", go to settings > system settings > Info and watch the number of Firmware if it starts V01 access the Thread called Fuze Firmware Updater, in the first post to find the update of the firmware that starts V01 and then follow the instructions on this post. If your Firmware number starts V02 find this firmware and follow the instructions.

• BDP-S350: problems AFTER firmware update

  I recently bought a copy of "Guardians of the Galaxy" on blu - ray, and when it arrived I put in my player SONY BDP-S350 and watched all of the 2D version of the film.  At this time there the S350 was running version 07.1.009 firmware.

  Then, I got the brilliant idea to do better all by updating my firmware.  After a bit of difficulty (entirely my fault - RTFM) I've successfully upgraded to the version of the firmware 07.2.026.

  I just tried to play the same disc of "Guardians of the Galaxy" that I saw before the upgrade and the S350 reports it is unrecognizable and is yet to play.

  Other, older, blu - ray discs play normally, and regular DVD movies play too.

  Anyone had this happen with a BDP-S350?  I know that firmware update is not removable... advice?

  Thank you!

  I solved it!

  I put a USB in the port to "EXT", thinking that it would so add wonderful new capabilities to my BDP-S350.   Instead, he sprayed some features and made it impossible to play a blu - ray disc that plays perfectly well than a week ago.

  I disabled the BDP-S350, removed the USB, back running the BDP-S350 and "Guardians of the Galaxy" playing right now!

  L8R...

• Linksys WAG54GS ver 1.1 firmware update

  I need to update my firmware before upgrading my ISP to the ADSL2 +. Research on the Linksys website, the latest firmware seems to be 1.01.03, but I understand that 03 is not compatible ADSL2 and it also has a version 1.01.11.  Can someone let me know where I can find it?

  Kate

  Just for this track myself--bad form, I know, but it should solve this problem for anyone else having the same problem.  I had a conversation of text with "Alan" Linksys who assured me that with version 1.01.03 firmware update my ADSL2 + works OK.  So I'll just wait for that person in the House got urgent business on the internet and then do the deed and hope for the best (I can be waiting for a while... )

  Kate

• Photosmart 7520: News on the firmware updated

  Hello

  I was talking to HP support problems with the latest firmware pushed for the 7520 breach ePrint and network services and they told me that there is an updated release due to be released for download via the software / support site, I was wondering when the new firmware is supposed to be available?

  Matt

  Hello

  A new firmware to restore the ePrint feature are available on hp.com, however it is currently available for MS Windows :

  http://support.HP.com/us-en/drivers/selfservice/swdetails/HP-Photosmart-7520-e-all-in-one-printer-series/5199461/model/5199462/swItemId/OJ-113641-5

  I don't know if / when it wil become available for Mac OS, that's why I suggest you get a Windows PC and update of the printer, if you can have such an or can borrow a laptop to a member, family, etc.

  If you need to use another PC, remember to install the printer drivers first prioor runs the update:

  http://ftp.HP.com/pub/softlib/software12/COL43773/MP-108670-3/PS7520_1315-1.exe

  Kind regards

  Shlomi

• The PRS - T1 firmware update does not complete

  EReader PRS - T1. Now that Sony's Reader store is closed, a new firware update redirects the reader to the Kobo store. Trying to do this update on the drive to fail with the "complete failure" message, tried again, not go. Tried on two different Windows 7 laptop computers and two different readers of PRS - T1. Both the same result. Where from here?

  I solved this problem, it's the latest firmware for the Sony Store closing.

  Sony did a bad job of coding, it does not check the space available on the drive. As the update needs to copy the updated firmware for the drive, the drive must exceed 100 meg free space to enable this. Two of my readers had less space to 100 meg. By removing some books in order to release the update about 110 meg proceeded until the end.

  Sony, get your coders education!

• HP zBook Studio G3: zBook Studio G3 - DEATH BY INTEL ME FIRMWARE UPDATE

  WARNING!

  DO NOT INSTALL THE UPDATE OF THE COMPONENT OF THE (COMPANY) INTEL MANAGEMENT ENGINE FIRMWARE!

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=8934841 & swItemId = ob_159465_1 & swEnvOid = 419...

  Component Firmware Intel management engine (ME) (American International)

  11.0.0.1194 Rev.A
  December 1, 2015

  We bought 5 of these laptops for our Engineering Department and I was against a tight schedule to get them deployed (the next day). I started working on obtaining a set of installation with the necessary software and then I just want to clone one for the other 5.

  I did a clean install of Windows 10 and installed all the drivers from the HP site. Then I ran Windows updates until everything is up-to-date. I disabled Windows Defender. Now all that remained was update the firmware BIOS, Intel ME and Thunderbolt using the downloaded utilities since the page drivers. The BIOS installed fine, but it's a really weird update process. Due to the beeps and lights blink during his work. There is no progress bar to let you know if she is doing anything. At some point, as the beeping stop but it's still really work. Then he starts and updates another part of the system and so on. Anyway, that everything worked fine. No problem with the update and Windows 10.

  So I ran the update of the Firmware of Thunderbolt and open up a command window saying that it couldn't find the controller. It looks like not there nothing after that point and just closed.

  Finally, I ran the Intel Management Engine firmware update utility. He opens a command window and says that it is loading the file and check and so on. Then he wrote the Flash file and takes a minute or two, doing so. Once it's done, the firm order window and back to business as usual... until you restart. Once you do this, the system is toast. It does not start. Black screen, fans run at high speed and the CapsLock and NumLock bulbs only 5 slow flashes indicating that there is something wrong with the motherboard. I'm starting a supported by HP chat session.

  I am told to disconnect the battery. To access the battery, you need a bit T - 8 Torx and you unscrew 11 screws to remove the grill cover and low fan (pedestal). I did that and disconnected from the battery. Reconnect after a few minutes and tried to start. Nothing, same thing. The support agent told me that a technician on site should be sent to replace the motherboard.

  While the lower lid has been opened, I noticed that there are two small LED lights near the SSD. There are supposed to be the diagnostic lights and I found an article in the service manual indicates if one of the LEDs is lit, the motherboard should be replaced. This lights a few seconds after the connection of the power supply for the laptop or by pressing the power button.

  I asked the support agent if they knew why it happened, but they did not know.

  So, I got 4 portable more to work with. I took off the dead laptop SSD and put a charge in a brand new out of the box. Started by and on the desktop Windows 10. This laptop had BIOS v1.03 on this subject so I ran the BIOS updated and rebooted. All right. At this stage I myself asked to perform other upgrades of the firmware or not. I thought that I had a 50/50 chance and I'm the kind of person that simply be whether it was a fluke or if there really was something seriously wrong with the update of the Intel ME firmware. He ran while first instead of love at first sight to date. Update Intel did ME the same thing before, opened a window to order, checked and then flashed... and after a reboot I got another laptop dead.

  At this point, I shook my head and frowned, looking at the HP logo.

  I tried calling support, but their laptop zbook/computer service has been closed from 10 is no support by phone or chat support. I have to wait until the morning to make a call in warranty for this second laptop dead.

  The Intel ME firmware update released on download of HP ZBook Studio G3 section was not compatible with these laptops and caused the laptop no longer starts. Only an exchange of motherboard could solve the problem. HP since then changed the link to the Intel ME firmware update for the appropriate softpaq.
  
  Those who had run the update of the bad firmware and their laptop brick had to call the HP technical support to schedule a replacement motherboard on the spot.