Access Port configuration

Similar Questions

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• Access Web configuration

  I have the router model BEFSR41 ver.4.1 and I use address IP in the address bar brouser to access the configuration page because my router is trying to block my Xbox to Xbox live. But ever time I try to open the installation page it asks me a username and password. I know the password by default but not the username. Could someone help me with this?

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  If the admin password does not work then you must reset and reconfigure the router...

  Press and hold the button of reset for 45 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL followthis link

  For X - Box, try this...

  Let the empty user name & password use admin lowercase...

  Click on the tab "Games and Applications" and then click the sub-tab "Port Range Forwarding"...

  (1) on the first line in the box, type Application in ABC, in the start box, type in 53 and type in 3074 service box, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable, click on save settings once it's been...

  (2) once you return to the game to the top page, click the Security tab and uncheck block anonymous Internet requests and click on save settings...

  3) click on Setup and change the size of the MTU to 1365 and click on save settings... Click the status tab, and take note of DNS1 and DNS2 address...

  (4) address IP, Goto settings XBox network settings and assign the following on your Xbox and select manual IP settings
  IP address:-192.168.1.20, subnet mask:-255.255.255.0 default gateway:-192.168.1.1...

  (5) also assign addresses DNS on Xbox
  Use DNS1 and DNS2 addresses you took note of the primary router as secondary DNS & DNS status tab for the xbox...

  (6) turn off your modem, router and Xbox... Wait a minute...

  (7) plug the power to the modem first, wait a minute and plug the router power cable, wait another minute and turn on the Xbox and... test it connects...

• Compare Dot1Q and QinQ with access ports and trunk?

  Hi all

  How do you compare Dot1Q and QinQ with access ports and trunk?

  Thank you

  Sunil Kumar

  Hey, Sunil,.

  With regard to your questions:

  1. we have a case of Dot1Q configured on the port of access of habit?  If not, then why? - Dot1q aims to tag executives leaving the switch and access is opposite, it does not therefore not used together marking.

  2. how the topology would be for QinQ case? - For QinQ as I mentioned in my last post one side will be set to while links to access than others. A simple example is explained on this link:http://networklessons.com/switching/802-1q-tunneling-q-q-configuration-example/

  HTH.

  Kind regards

  RS.

• Printer port configured incorrectly, how to remove or reconfigure

  I am setting up a new system of Windows 7 Home premium and made a mistake when setting up the new machine to access one of my existing home network printers. I have incorrectly set up a new printer port and need to know how to remove it.  When I try to install the network printer now (rightly), the wizard tells me to choose another port name because what I used already exists.  The port name is unique to my existing print server (DLink DP-G321) and should be used for this printer.  Can someone tell me how to remove the bad port configuration, or get the wizard you want to replace it?  I suspect that this may require a registry hack, which I have no problem to try with the correct instructions.  Thank you

  The 720C will not work on x 64 machines.  I contacted HP in this regard.

  "HP DeskJet 720C" is HPVDJ720. GPD.

  [HPVDJ720. GPD. CIM]

  E-mail address is removed from the privacy *, @HPVUD50. DLL,@HPVUI50. DLL,@HPVIMG50DLL,@HPVDB720. DLL,@HPVSCP50. DLL,@HPV700AL. DLL,@HPVDJ7XX. GPD,@HPVDJ720. GPD,@HPVNAM50. GPD Alan Morris Windows printing team; Here Microsoft Knowledge Base search: http://support.microsoft.com/search/Default.aspx?adv=1

• D DAQMx 6229 problems default IO port configuration

  Hello

  We use the PCI-6229 in an industrial PC / Windows 7 CVI application and are interested in the power setting to the top of the default configuration for the input/output digital port configuration.

  We used the utility NI Max Device Explorer and config to set the default values for the configuration of our application 26 DI + 6.

  It works very well which allows us to turn off the PC and power again upward and the Council retains its power to configuration.

  When we run our application and power cycle the PC, the power of the State seems to have returned to factory settings, which is all the output to 0 (I think).

  I don't think that we are running the functions that perform all reset of the card.

  Did someone saw this behavior like this and have any ideas of how we can know how to solve this problem?

  Thanks in advance.

  Steve Pinfold

  Hi Steve,.

  I conducted a survey on this issue, and it seems that this is a known bug and was returned in October last year.

  There is however a workaround solution.

  Cannot set the State of a single line at a time, because that will generate an error kErrorPowerupStateNotSpecdForEntirePort. Instead of so, write several DAQmxSetDigitalPowerUpStates() with different hardcoded calls a number of settings and switch between them during execution. I joined ppus_set.c, which is supposed to randomly through the adjustment lines.

  I hope that this should be a good starting point for you!

• Printer does not work on the Windows XP computer, get the error message like "an error occurred during port configuration. This operation is not supported.

  Original title: 1. printer stopped communicating with the computer. 2 port - associated configuration error?

  I have a big problem. All of a sudden my printer - AIO Photo964 said he cannot communicate with my computer. The printer works fine. I tried switching cables USB, all the trouble shooting suggestions, etc. etc. Nothing works and it makes no sense. I can't print anything. I thought it would be that I installed a Seagate external hard drive backup, then I uninstalled the program - no help. ITunes installed recently, because she had changed the printer default, changed back - no help. The USB cable is not tight in the printer (or both cables, I tried), but AFAIK it's not new (?) And when I try to configure the port, I get the error message "an error occurred during port configuration. This operation is not supported"I have no idea what it means.  Can someone help me with this? I have to return a new printer? The USB port on the printer is repairable if this is the problem? How will I know? Who would do that?

  Thanks, I'd appreciate any help.

  It is always useful to have the complete error message without paraphrase.

  It also helps to identify the version of Windows you have, including service pack.

  And it helps to give the manufacturer of the printer in addition to the model.  In your case, I guess you have a Dell printer.  I know that some Dell printers are rebadged Lexmarks, but I don't know if it's a.

  Why you try to configure the USB port?  It cannot be configured - you've discovered.  It's normal.

  It's quite strange that an iTunes installation would have had something to do with the printers.  What printer was made by default after installing iTunes?

  You say you have tried another USB cable.  Have you tried using a different USB port on the computer? Have you checked in the Device Manager (start > run > devmgmt.msc > OK) to see if there is all the warning icons in the category "controllers of Bus USB?

  I suggest you uninstall the printer software and driver completely and reinstall by following the directions in Its first Article.

  Don't skip step 4.  After step 4 and step 5, follow these steps:

  Important: If you have a Lexmark printer, skip the following

  Open a command prompt window (start > run > cmd > OK)
  type the following in the black command prompt window, and then press ENTER after each line

  net stop spooler
  dependent on the spooler of sc config = RPCSS
  net start spooler
  output

  Note that there is no space before the = and there is a space after it.

  The Windows XP driver for the Dell Photo AIO 964 printer is here--> http://www.dell.com/support/drivers/us/en/04/DriverDetails/DriverFileFormats/Product/dell-964?DriverId=R113115&FileId=2731111743&urlProductCode=False

• Unable to access WRT1900AC configuration page when it is configured as AP only

  Problem: cannot access configuration page of WRT1900 or by using the linksyssmartwifi or the affected DHCP an address

  Configuration: I have a domain Active directory to manage all devices in my house and customers. MY ISP is uVerse.

  I first installed uVerse and the WRT1900 as being generally configured (uVerse providing DHCP and DNS), my field devices could not resolve the local my AD server domain name. To resolve this problem, I set up my server AD 2003 to act as a router, Server DNS and DHCP (see diagram below).

  In this configuration, all connected via LAN or WiFi devices can see internet and other LAN/WiFi field devices connected.

  The only problem I have is that I can't access the configuration page of WRT1900 or by using the linksyssmartwi or the address assigned DHCP

  The 2003 Server provides DHCP to all devices in the LAN attached including WiFi LinkSys attached devices

  Server 2003 provides DNS name resolution

  

  in my case it seems that the opposite was true.  I reset my router, which is configured as a LAN Gateway and now I can access limited menu.  most applications have disappeared and I can't do basic as things even see who is connected.  Almost everything that is available is to put the passwords for wifi access and the router itself.

  It will not even to change channels or wifi connection protocols.  Shame on Linksys for not properly support their interface.

  The good news is the still phone app works where some of the above items can still be configured (for example, you can configure at least most of the wifi settings)

  Thanks for your help!

• E2500: 'the connection to the 192.168.1.1 was interrupted." When you access the configuration page.

  Trying to access the configuration page, 'the connection to the 192.168.1.1 was interrupted."  I'm wired into the router.  Any idea of what is the cause?

  Ugh, I'm stupid... I was using the button in the back instead of the reset button on the bottom.  Thanks for the tip-off that the reset method should have worked.

• WRt160N is unable to access the configuration screen after the demotion to a lower version

  I just bought WRT160-V2 two weeks ago. The connection kept down all the minutes. After reading some threads in this forum, discovered that I was not alone. A thread under the instructions of a http://audipages.com/router/ site. So I upgraded my router for firmware v2.0.0.02 build 008. The connection is much more flexible. However, Setup screem has not come back. Now, I am not able to access the configuration with 10.10.10.1 screen. Help, please. Thanks in advance!

  After an update of the firmware, you must reset the default router, and then configure the router again from scratch.  If you have not done this since your last update of the firmware, please do it now and see if it solves your problem.  If you have saved a router configuration file, DO NOT use it.

  To reset your router prress the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

• WRT54GX4 - difficulties to access the configuration Page of the router Web-based

  WRT54GX4 - difficulties to access the configuration Page of the router Web-based.

  I have tried all posted to forums and knowledge for several weeks now with no luck.  I can feed the router to push and access the router's web-based interface, but only for a few minutes that she was leaving the loading to half way through and or does not load.  If I turn on the wireless side I can access the router at will without any problem. My warranty is almost over. I'm at my wits end. I would like to replace it under warranty if I can. (^ 8.

  Update: I fell up on top of the fix for my problem. After many reconfigurations over the past two months I've tried turn on all newspapers. Since the age of the newspaper I did have a problem of access to my router.

• After installing a new HARD drive, I get a screen "control i to access the configuration utility.

  Help?

  I installed a new HARD drive on my xps 15 because the old drive crashed. Everything works fine and the system boots perfectly. Before entering the Dell splash screen, the screen "control i to access the configuration utility" appears for 5 seconds. After that, the normal boot sequence resumes. Can someone please explain to me why this is happening and what I can do about it?

  Here is a link to the screen I get started: http://s102.photobucket.com/user/alexcinie/media/photo_zpsb75f0a7f.jpg.html

  The mSATA drive is used as a cache for the hard drive dynamic - these are essentially implemented in a RAID 0 array.  See the link below (it is for Alienware, but applies to your system as well).

  If you want to keep the disk cache, you need to configure the array as shown.

  http://www.Dell.com/support/troubleshooting/us/en/04/KCS/kcsarticles/ArticleView?docid=564442

• Series 5300 MCUS are supported by the flexible port configuration?

  Hi all

  I could not find a guide to the administrator or something for the MCU5300 series. I want to learn if the ports are flexible or not. You know that it supports up to ports 20HD or 40SD. Is it possible to make this support 10HD and 20 ports SD at the same time as Polycom RMXes? Or do I have to choose a mode (HD or SD) and to use them only in this mode?

  Best regards

  Chambers oumar

  From what I understand, it is the characteristics of the MSE8510 in a standalone MCU.

  On the MSE8510 is not possible, then I say:

  No, it is not possible to have a flexible port configuration.

  So yes, it is a fixed parameter.

  Here, some more old, posting on the MSE8510:

  https://supportforums.Cisco.com/thread/2132414

• Can someone help me with printing. My settings have been changed. I have a printer Epson Stylus and pse 13. I can't access the configuration screens that they show that I need to access.

  I can't access the configuration screens that they show that I need to access.

  What is a forum. I don't understand. I'm 63 and they will not access my computer at ADobe

  I can't access the configuration screens that they show that I need to access.

  What do you need access? When you encounter a problem?

  What is a forum. I don't understand.

  A forum is a place which provides for exchanges between users.

• Unable to access the configuration of the EA6900v1.1 web page

  Hi guys,.

  I bought a second hand ea6900, the guy had its ssid wifi in there, so I took over and reset immediately.

  to reset that, I like the reset button, waited for the flash logo and then become solid.

  I can connect to it wired and wireless, however, when I type in 192.168.1.1. He takes me to smart wifi configuration page, that requires the internet connection or the router access password, I tried admin, password, empty, etc. non of them work.

  I plugged a cable to the internet port of my router/box of fiber, and it does not connect to the internet either.

  I also tried to update the firmware, http://www.linksys.com/us/support-article?articleNum=159332

  using the management http://www.linksys.com/nz/support-article?articleNum=140001 mode

  or TFTP method http://www.linksys.com/nz/support-article?articleNum=137928

  the two did not work, he brings me to the page of the wifi chip, when I tried to access the management mode,

  and it's the same thing when I press reset for a minute. always take back me to the wifi secruit and need this password.

  These items are Linksys live chat, after they discovered that his warranty has expired

  anyone would be able to help?

  Thank you

  Adam

  OK... This is simply ridiculous. I use IE to connect with admin, chrome does simply not work.