Access VPN with expired password code
Is there a way to manage passwords expired on the ASA 5520 vpn users? We currently use the Windows 2008 Server NPS server as a Radius Server, which is located on a domain controller. When a VPN user attempts to log on if their password has expired, I would somehow put the user on a 'quarantine' VLAN and let them choose a new password right now, they just authentication failure. We use SSL VPN and AnyConnect client.
You can use the command 'the password management'. Please see this post https://supportforums.cisco.com/thread/2149986
Please rate if this can help
Tags: Cisco Security
Similar Questions
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Is it possible to send a pdf that they alone can / access view with a password for a password protected?
Thank you!
Hi wonderingtoday,
Yes, you can! If you have Acrobat, you can assign a "Password" in the PDF Open, so that only those with the password can open the PDF file. If you do not have Acrobat, you can try it free for 30 days. For more information, see www.adobe.com/products/acrobat.html.
Best,
Sara
-
ASA to remote access VPN with external IP dynamic
Hi forum,
I was wondering if it was possible to set up an ASA to provide access to remote connections VPN (IPSEC or WebVPN/SSL) of the outside world, if the external IP address is dynamic (i.e. obtained through DHCP)? I understand how to use DynamicDNS to provide a host name for the VPN clients, I ask simply if the SAA can be configured to allow VPN connections from a DHCP interface addressed. I understand there are problems with the site to site VPN when both sides are addressed in a dynamic way, but it seems that the remote VPN access should work. Just hoping to confirm this before I go and I'm working on a config.
Thanks in advance...
The same configuration applies.
In my view, that the only difference is that with the external IP being dynamic:
interface e0/0
IP address dhcp setroute
crypto map
The only difference is that (the PCF file) VPN clients should have the VPN connection with a hostname (rather than an IP address) and the IP must be solved at the IPs of the SAA.
I'll try to find you an example configuration if you do not.
Federico.
-
View Client to connect with expired password
Hello
One of our users has changed his password of Windows through the VMware view client. After a few minutes it disconnects and connects back with the old password and customer view allowed him to reconnect.
But he was allowed to log in when he got connected to the desktop "password username Incorrect please enter the appropriate credentials. Is there a way that we can avoid this?
We use the Horizon view 6 with Wyse D90D7 Windows embedded customers.
Horizon View Client version 3.1
Please notify
It will be down to the local domain to the computer thinclient controller. A password must be replicated instantly, as it is reported as an urgent change. Best to check the local domain controller and that it the replication on OK. Can you see where the user changes his password and check out the ads and Services Sites and make sure your customers are in a site with a domain controller that runs. If it's a RODC then check the password replication policy.
-
PT 8,53 expired password Causes Invalid access ID
People,
Hello. I've been running PeopleTools 8,53 Internet Architecture with Oracle Database 11 g 1 material and OS Oracle Linux 5 for awhile. PSADMIN connection in the browser of the user successfully. All applications run correctly.
A few weeks ago, I started an application server and received the error message as below:
"Password expires less than 6 days. Could not sign on user PSADMIN. »
I followed the tutorial of Nicolas http://gasparotto.blogspot.com/2010/03/psovm-sysadms-password-policy.html to do step by step below:
Step 1:
SQL > select username, ACCOUNT_STATUS, EXPIRY_DATE, PROFILE of dba_users;
His output: 10 rows back as below:
OUTLN Expired (Grace) 15 April 14 by DEFAULT
MYNAME Expired (Grace) 15 April 14 by DEFAULT
PEOPLE Expired (Grace) 15 April 14 by DEFAULT
PS Expired (Grace) 15 April 14 by DEFAULT
SYS Expired (Grace) 15 April 14 by DEFAULT
By default the SYSTEM Expired (Grace) 15 April 14
TSMSYS expired & locked by DEFAULT
DINH expired & locked down by DEFAULT
DBSNMP expired & locked down by DEFAULT
ORACLE_OCM expired & locked down by DEFAULT
As you can see above, the PSADMIN user isn't here. MYNAME is my ID of owner of Oracle database as well as the Linux login ID.
Step 2:
SQL > select * from dba_profiles where the profile = 'DEFAULT' and limit is not null and limit! = "UNLIMITED";
Its outputs: 5 rows back as below:
10 FAILED_LOGIN_ATTEMPTS DEFAULT PASSWORD
PASSWORD_LIFE_TIME 180 DEFAULT PASSWORD
DEFAULT PASSWORD NULL PASSWORD_VERIFY_FUNCTION
PASSWORD BY DEFAULT PASSWORD_LOCK_TIME 1
PASSWORD BY DEFAULT PASSWORD_GRACE_TIME 7
Step 3:
SQL > changing the default profile limit
Unlimited failed_login_attempts
Unlimited password_life_time
Unlimited password_lock_time
password_grace_time unlimited;
Its release: modified profile.
Step 4:
SQL > alter user MYNAME identified by MYNAME;
Its release: modified user.
I do the same for the PEOPLE, PS, SYS, SYSTEM and OUTLN user.
Step 5:
SQL > select username, ACCOUNT_STATUS, EXPIRY_DATE, PROFILE of dba_users;
Its outputs:
OUTLN, MYNAME, PEOPLE, PS, SYS, SYSTEM, ACCOUNT_STATUS for each one is OPEN and no expiration date.
Finally, I start application server and got the error in APPSRV_0422.LOG as below:
«GenMessage Box (0,0,M): database access code: access code invalid or password database Signon.» Server was able to start. »
I think that the access code for the database feature is PSADMIN but is not in the table dba_users.
In the configuration of the Application Server domain: UserId is PSADMIN, login Id is "people".
I see no error in the above 5 steps to solve the issue expired password.
My question is:
All folk can help solve a problem 'Access Code invalid or pwd for identification of the database?
Thanks in advance.
Hello
You can view the rest of documents
E-SEC: how to change symbolic ID. access, SYSADM password? (Doc ID 609603.1)
E SEC: 2 - Tier connection error "Invalid ID and password for Signon" (Doc ID 611500.1)
I will suggest you to exclude users of password control that starts the application server.
You can consult the following document
E-SEC: password controls can be specific user? (Doc ID 611621.1)
Kind regards
Sanjay Pandey
-
Hello
I have a thin client HP 5740e and for some reason any local user account requires a password change. Yet, when I try to change the password it says access denied. And yet, I can't it to allow me to move to another counts as administrator to open a session. I held down the SHIFT key during startup, but it always goes straight to this local user account & the expired password prompt. I'm stuck in an infinite loop and do not know how to cope. Safe mode puts me in the same situation. And I can't update the BIOS because I can't have everything.
OS = Windows Embedded Standard 7
I also tried to reinstall the last image of the HP Web site using a USB key, but it fails every time. I tried 2 different USB drives with the same exact error no each.
Image, try to install = SP56020
ERROR: An unexpected condition has occurred
Does anyone have a suggestion?
I finally could get as an administrator using RDP to my office. I didn't know the name of thin client lacked a figure, that's why I've been unsuccessful before that.
Once I got away, I could watch the local user account permissions. Now I see what was wrong.
[Check] The user cannot change password
[Disabled] Password never expires
I still don't know why I couldn't install a new image of the plant, but at least I am now able to work with this device. I also disabled the automatic connection at the moment.
Sorry to have littered the Forum!
-
original title:
Finally, I registered my account some time in August, 2010. I noticed that when I tried to sign new after trying to connect using a mobile phone, has been denied access. Saying: my account has been blocked because I tried o identify you on several occations. My pin code is * and my email is * address email is removed from the privacy * help me with my password recovery I did not had access to my account for some time. Thank you and God bless you!
Hello
you ask about Hotmail?
If so, we can help you not in these responses Vista Forums
Please repost your question in hotmail in the hotmail link below forums
http://windowslivehelp.com/product.aspx?ProductID=1
ForumsConsult with Microsoft Certified Solutions -
Anyconnect VPN management if password password has already expired
Hello
I have ASA Cisco AnyConnect vpn with Microsoft AD ldaps authentication. In the Group of the tunnel, I configured management password (password expire days 14). It works but my testing it seems to be no possible to update the password if it is already expired. No way to solve this problem?
Thank you
Hi, Giuseppe.
Yes, the change of password should work even when he arrived at expiration.
Maybe you can try placing screenshots on the user and the server and make sure that the TCP process is successful when the password has expired.
-Javier-
-
Cisco ACS 5.1 and ASA SSL VPN change or notify the expired password
Hello
Now, my ACS and ASA related to RADIUS (MSCHAPv2). I've set up password life on GBA and password management on SAA. But Cisco ASA did prompt change or whatever it is to notify when the user tries to log on with Clientless SSL VPN. Could you advice me everything to change, or notify the expired password?
PS.
I check change password on the first login of th on ACS this confirmation of the ASA to change password dialog box. But I want change or warn when the expired password
Thank you
The default password is marked as disabled after expiry
I think that there is an improvement for this in the 5.2.0.26.2 patch and above, which includes the following:
CSCtk32168: Add an option to change the password when the password expires (T + and Radius)
After you install this hotfix, you get an option to the user authentication settings is:
-Disable the user account
-Expire the password
When the expiration period is exceeded
If password is expired then user will be asked to change password next authentication
Note this latest patch for 5.2 is 5.2.0.26.4. All patches are cumulative
-
Remote access VPN group name and password
Hi guys,.
Can someone tell me please the command to display a remote access VPN group name and the password on a firewall version 8.0 of ASA? Any help will be greatly appreciated.
Thank you
Lake
Remote VPN IPsec IKEv1 access are listed as groups of tunnel. If you enter
more system:running-config | b tunnel-groupYou can see the config sections (starting with the first mention of the tunnel-group) as well as the pre-shared key ikev1 plaintext String.
-
Another problem with the configuration of Cisco VPN Client access VPN Site2site
We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site. JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support. So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0
Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.
CORP netowrk 192.168.1.0
IP VPN 192.168.12.0 pool
Colo 10.1.0.0 internal ip address
Also, here's an example of my config ASA
: Saved
:
ASA Version 8.2 (1)
!
hostname lwchsasa
names of
name 10.1.0.1 colo
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
backup interface Vlan12
nameif outside_pri
security-level 0
IP 64.20.30.170 255.255.255.248
!
interface Vlan12
nameif backup
security-level 0
IP 173.165.159.241 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 12
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network NY
object-network 192.168.100.0 255.255.255.0
BSRO-3387 tcp service object-group
port-object eq 3387
BSRO-3388 tcp service object-group
port-object eq 3388
BSRO-3389 tcp service object-group
EQ port 3389 object
object-group service tcp OpenAtrium
port-object eq 8100
object-group service Proxy tcp
port-object eq 982
VOIP10K - 20K udp service object-group
10000 20000 object-port Beach
the clientvpn object-group network
object-network 192.168.12.0 255.255.255.0
APEX-SSL tcp service object-group
Description of Apex Dashboard Service
port-object eq 8586
object-group network CHS-Colo
object-network 10.1.0.0 255.255.255.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.1.0 255.255.255.0
host of the object-Network 64.20.30.170
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
ICMP service object
service-object icmp traceroute
the purpose of the service tcp - udp eq www
the tcp eq ftp service object
the purpose of the tcp eq ftp service - data
the eq sqlnet tcp service object
EQ-ssh tcp service object
the purpose of the service udp eq www
the eq tftp udp service object
object-group service DM_INLINE_SERVICE_2
the purpose of the ip service
ICMP service object
EQ-ssh tcp service object
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0
outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
outside_pri_access_in list extended access permit tcp any interface outside_pri eq www
outside_pri_access_in list extended access permit tcp any outside_pri eq https interface
outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100
outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface
outside_pri_access_in list extended access permit icmp any any echo response
outside_pri_access_in list extended access permit icmp any any source-quench
outside_pri_access_in list extended access allow all unreachable icmp
outside_pri_access_in list extended access permit icmp any one time exceed
outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586
levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0
outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0
outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0
outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0
Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list
OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0
L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
exploitation forest asdm warnings
record of the rate-limit unlimited level 4
destination of exports flow inside 192.168.1.1 2055
timeout-rate flow-export model 1
Within 1500 MTU
outside_pri MTU 1500
backup of MTU 1500
local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 100 burst-size 5
ICMP allow any inside
ICMP allow any outside_pri
don't allow no asdm history
ARP timeout 14400
NAT-control
interface of global (outside_pri) 1
Global 1 interface (backup)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside_pri) 0-list of access OUTSIDE-NAT0
backup_nat0_outbound (backup) NAT 0 access list
static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns
static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns
Access-group outside_pri_access_in in the outside_pri interface
Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1
Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254
Timeout xlate 03:00
Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
http server enable 981
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside_pri
http 0.0.0.0 0.0.0.0 backup
SNMP server group Authentication_Only v3 auth
SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection tcpmss 1200
monitor SLA 123
type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri
Annex ALS life monitor 123 to always start-time now
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outside_pri
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_pri_map 1 match address outside_pri_1_cryptomap
card crypto outside_pri_map 1 set pfs
peer set card crypto outside_pri_map 1 50.75.217.246
card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5
card crypto outside_pri_map 2 match address outside_pri_cryptomap
peer set card crypto outside_pri_map 2 216.59.44.220
card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
86400 seconds, duration of life card crypto outside_pri_map 2 set security-association
card crypto outside_pri_map 3 match address outside_pri_cryptomap_1
peer set card crypto outside_pri_map 3 216.59.44.220
outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
card crypto outside_pri_map interface outside_pri
crypto isakmp identity address
ISAKMP crypto enable outside_pri
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 50
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
!
track 1 rtr 123 accessibility
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd auto_config outside_pri
!
dhcpd address 192.168.1.51 - 192.168.1.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
rental contract interface 86400 dhcpd inside
dhcpd field LM inside interface
dhcpd allow inside
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection host number rate 2
no statistical threat detection tcp-interception
WebVPN
port 980
allow inside
Select outside_pri
enable SVC
attributes of Group Policy DfltGrpPolicy
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal GroupPolicy2 group strategy
attributes of Group Policy GroupPolicy2
Protocol-tunnel-VPN IPSec svc
internal levelwingVPN group policy
attributes of the strategy of group levelwingVPN
Protocol-tunnel-VPN IPSec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl
username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard
aard attribute username
VPN-group-policy levelwingVPN
type of remote access service
rcossentino 4UpCXRA6T2ysRRdE encrypted password username
username rcossentino attributes
VPN-group-policy levelwingVPN
type of remote access service
bcherok evwBWqKKwrlABAUp encrypted password username
username bcherok attributes
VPN-group-policy levelwingVPN
type of remote access service
rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username
rscott username attributes
VPN-group-policy levelwingVPN
sryan 47u/nJvfm6kprQDs password encrypted username
sryan username attributes
VPN-group-policy levelwingVPN
type of nas-prompt service
username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0
username cbruch attributes
VPN-group-policy levelwingVPN
type of remote access service
apellegrino yy2aM21dV/11h7fR password encrypted username
username apellegrino attributes
VPN-group-policy levelwingVPN
type of remote access service
username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5
username rtuttle attributes
VPN-group-policy levelwingVPN
username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin
username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0
username nbrothers attributes
VPN-group-policy levelwingVPN
clong z.yb0Oc09oP3/mXV encrypted password username
clong attributes username
VPN-group-policy levelwingVPN
type of remote access service
username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0
username attributes finance
VPN-group-policy levelwingVPN
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
type of remote access service
IPSec-attributes tunnel-group DefaultL2LGroup
Disable ISAKMP keepalive
tunnel-group 50.75.217.246 type ipsec-l2l
IPSec-attributes tunnel-group 50.75.217.246
pre-shared-key *.
Disable ISAKMP keepalive
type tunnel-group levelwingVPN remote access
tunnel-group levelwingVPN General-attributes
address LVCHSVPN pool
Group Policy - by default-levelwingVPN
levelwingVPN group of tunnel ipsec-attributes
pre-shared-key *.
tunnel-group 216.59.44.221 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.221
pre-shared-key *.
tunnel-group 216.59.44.220 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.220
pre-shared-key *.
Disable ISAKMP keepalive
!
!
!
Policy-map global_policy
!
context of prompt hostname
Cryptochecksum:ed7f4451c98151b759d24a7d4387935b
: end
Hello
It seems to me that you've covered most of the things.
You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel
outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo
Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.
-Jouni
-
VPN (remote access, ASA5520) with 2 clients, one with Internet and other without Internet
Hello! I make a VPN with two clients, using the ASA5520 United Nations. Now I have to do what the customer has internet and the other does not. I can do using ACL? How?
The configuration is:
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.16.31.252 255.255.255.248
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 172.16.1.237 255.255.255.240
Access extensive list ip 172.16.1.224 ACLnonat allow 255.255.255.240 host 172.16.1.230
Standard access list Split_tunnel allow 172.16.1.224 255.255.255.240
IP local pool testpool 172.16.1.230 - 172.16.1.232 mask 255.255.255.240
NAT (inside) 0-list of access ACLnonat
Route outside 0.0.0.0 0.0.0.0 172.16.31.254 1
Crypto ipsec transform-set esp-3des esp-md5-hmac hw_trans
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map dyn_map 1 transform-set hw_trans
Crypto dynamic-map dyn_map 1 the value reverse-road
stat_map 10000 card crypto ipsec-isakmp dynamic dyn_map
stat_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 3600
Crypto isakmp nat-traversal 30
internal hw_policy group policy
attributes of the strategy of group hw_policy
value of server DNS 193.205.160.3
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_tunnel
Split-dns value 193.205.160.3
username User1 encrypted password privilege 0 pqA3EDHB1cfLxwWn
password username User2 FIQ1c02tX8lU1wHJ encrypted privilege 0
attributes of user User2 name
VPN-framed-ip-address 172.16.1.233 255.255.255.240
allow password-storage
type tunnel-group hwclients remote access
tunnel-group hwclients General-attributes
address testpool pool
Group Policy - by default-hw_policy
hwclients group of tunnel ipsec-attributes
pre-shared key *.
ISAKMP retry threshold 30 keepalive 5
Thanks in advance.
Hello Jose,.
I see that you use LOCAL authentication, what you can do is, you can create another political group and link this political group for the user name, example:
attributes of group PALLET policy
Split-tunnel-policy tunnelall
name of User1 user attributes
RANGE of VPN-group-policy
The other username will use hw_policy, since it is the default value for the tunnel-group hwclients.
HTH
AMatahen
-
Why my Cloud connectors expire with Eloqua password?
I recently added some calculator cloud connectors to my innate program date. Then my Eloqua password expired recently. Apparently, this caused all my Cloud Connector passwords also expire.
- Why did I not receive an email notice that all these connectors cloud has expired and therefore caused my stall programs?
- How can I prevent my cloud connectors to exhale with my password? It is such an inconvenience to have to go back in every single program and re - enter new password Eloqua.
Hi Krista, Eloqua our peeps can correct me if this is not correct, but I think that the solution for this is to set up a new user in Eloqua with access to the API. The value that the user so that they do not have to change the password, then press the shoulder of your support rep first to make sure this password does not expire. At least that's what (I believe) we come to one of our cloud connectors that we have put in place the week last with the help of our representative.
-
I have Apple TV gen 1. I changed my iTunes password and now I can't the Apple TV in the House. It will connect to iTunes. I type my Apple and a new password. My phone Gets a text with a verification code, but the Apple TVsaybadusername password or.
Your ATV1 has an old software system not updated for years. You have 2 factor (6 digits) or authorization of step 2 (4 digits) enabled for your Apple account. Here are the characteristics of the latter. I disable these on your Apple account and try again.
For Apple ID - Apple Support two-factor authentication
Frequently asked questions about the audit in two steps for Apple ID - Apple Support
Maybe you are looking for
-
Re: Equium A300D: need XP WLan & driver graphic
Hello. I have trouble finding drivers XP for my A300D. I ve managed to get everything works perfectly except the WIFI and the graphics card.I downloaded all the drivers for my laptop from the Toshiba site, but when I tried to install the ATI drivers,
-
SpeedStep technology is available in Satellite L300-11 q
Hello! Is option SpeedStep included in model Toshiba Satellite L300-11 q? Thank you!
-
Should I worry that my battery icon went from green to gray? He is currently 72% charged.
-
Whenever I use to connect to hotmail or facebook or anything else, the guest of fingerprints would come and ask me knocking on swiping, but something happened and now it does not appear and I am connected automatically. How can I get the guest of fi
-
How to open the files. ORF in Camera Raw 9.6.1 for Photoshop CC 2015.5.1?
Hello, I subscribed to the creative Cloud offer by monthly subscription in France: all is well except that I have a version of the camera Olympus OM - D EM10 1 and is listed as compatible with Adobe Camera Raw for its RAW files that are. Extension of