Add VPN users to 1801 router

Similar Questions

• ASA does not propagate any routes for VPN users

  Good afternoon

  I m a problem concerning the spread of the roads to authenticated VPN users through the asa tunnel-group.

  I have a VPN-users-pool where my users receive their IP address, and after authentication and the tunnel is established the idea is that the user get to the networks defined in the following ACL:

  access-list within the standard allow 10.1.0.0 255.255.0.0

  access-list within the standard allow 192.168.15.0 255.255.224.0

  Now, the problem is that, after the tunnel is set up the only way, that the user receives is the default route (which is not supposed to be sent). The user does not receive the roads specified in the ACL list above. It has not received the network mask and assumes one 8 netmask (given that the pool of network from where it receives the IP address is a class A network).

  Network routing works as expected (when I add the static routes directly to PC users, everything works OK). It s just the matter of the ASA do not spread the roads as it should.

  Here is my split tunneling settings:

  attributes of Group Policy DefaultRAGroup

  VPN-idle-timeout 1

  Protocol-tunnel-VPN l2tp ipsec

  disable the PFS

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  attributes of Group Policy DfltGrpPolicy

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  Any ideas?

  I have apreciate your help

  Best regards

  Just a question, I see:

  attributes of Group Policy DefaultRAGroup

  Protocol-tunnel-VPN l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  internal DefaultRAGroup_1 group strategy

  attributes of Group Policy DefaultRAGroup_1

  Split-tunnel-policy tunnelspecified

  It looks like your policy

  DefaultRAGroup_1 you set ACLs and the other doesn't seem to be for L2TP/IPSEC. How do you connect to the ASA, using L2TP/IPSEC or Cisco IPSEC client? In addition, if your users are devoted to this group policy:

  DefaultRAGroup_1 it looks like the acl is missing for the split tunneling

• Download ACL for VPN users. ACS 4.1 & 1841 router

  Hello

  I have configured the router 1841 as a VPN server. All VPN users get authenticated using RADIUS ACS 4.1

  I need to apply downloadable ACLs by user.

  I configured the Downlodabale ACL ACS. Same ACS event report shows that the ACL is applied to the authenticated user, but traffic is not blocked or past accordingly.

  What is your configuration?

  I think that the more easy to do is to use IPSEC TIV in interfaces, as well as the aaa authorization network and on the radius server, use ip:inacl to the cisco av pair, as

  IP:inacl #1 = permit tcp any any eq 80

  IP:inacl #2 = permit tcp any any eq 443

  ...

  Some documents:

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t14/feature/guide/gtIPSctm.html#wp1090634

• Routing of a VPN from Site to site to remote VPN users

  Hello

  We have a site and remote vpn site configured in the same interface in ASA 5520 (software version 8.3). When the remote vpn users try to connect to the computers located at the far end of the site to site VPN, their request has failed. I tried No.-Nat between remote vpn IP private to the private IP address of remote site, also said the same split tunneling. I can't find even the tracert, ping has also expired.

  Is there any solution to make this live thing.

  Shankar.

  There are a few things that need to be added to make it work:

  (1) on the SAA where remote vpn users connect to, you must add "permit same-security-traffic intra-interface"

  (2) you mention that you have added the LAN of remote site-to-site in the list of split tunnel, so that's good.

  (3) on the SAA ending the vpn for remote access, you must also add the following text:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  (4) on the ASA site to remote site, you must add:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  -No - Nat: ip access list allow

• Remote VPN users

  Hello

  I would just ask how many simultaneous remote client VPN users is allowed for a Cisco1841 router? Are there licenses required?

  Also, will there be a degradation of the performance of the router if there as 15 concurrent users active remote client and VPN L2L 2?

  Thank you!

  For IPSEC, I don't think that there are all the necessary licenses. For SSL, they (but it still works without the license, but unethical).

  Concerning

  Farrukh

• LAN to lan vpn between ASA and router 7200

  Hi friends,

  I need to configure the lan to lan between ASA vpn (remote location) and router 7200 (on our network).

  <7200 router="" (ip="" add:="" 10.10.5.2)="">-(Internet) -<(IP add:="" 192.168.12.2)="" asa(5510)="">---192.135.5.0/24 network

  I will have the following configuration:

  7200 router:

  crypto ISAKMP policy 80

  the enc

  AUTH pre-shared

  Group 1

  life 3600

  ISAKMP crypto key cisco123 address 192.168.12.2

  Cryto ipsec transform-set esp - esp-md5-hmac VPNtrans

  map VPNTunnel 80 ipsec-isakmp crypto

  defined by peer 192.168.12.2

  game of transformation-VPNtrans

  match address 110

  int fa0/0

  IP add 10.10.5.2 255.255.255.192

  IP virtual-reassembly

  no ip route cache

  Speed 100

  full duplex

  card crypto VPNTunnel

  access-list 110 permit ip any 192.135.5.0 0.0.0.255

  ASA:

  int e0/0

  nameif inside

  security-level 100

  192.135.5.254 Add IP 255.255.255.0

  int e0/1

  nameif outside

  security-level 0

  IP add 192.168.12.2 255.255.255.240

  access-list ACL extended ip 192.135.5.0 allow 255.255.255.0 any

  Route outside 0.0.0.0 0.0.0.0.0 192.168.12.3 1

  "pre-shared key auth" ISAKMP policy 10

  ISAKMP policy 10-enc

  ISAKMP policy 10 md5 hash

  10 1 ISAKMP policy group

  ISAKMP duration strategy of life 10-3600

  Crypto ipsec transform-set esp - esp-md5-hmac VPNtran

  card crypto VPN 10 matches the ACL address

  card crypto VPN 10 set peer 10.10.5.2

  card crypto VPN 10 the transform-set VPNtran value

  tunnel-group 10.10.5.2 type ipsec-l2l

  IPSec-attributes of type tunnel-group 10.10.5.2

  cisco123 pre-shared key

  card crypto VPN outside interface

  ISAKMP allows outside

  dhcpd address 192.135.5.1 - 192.135.5.250 inside

  dhcpd dns 172.15.4.5 172.15.4.6

  dhcpd wins 172.15.76.5 172.15.74.5

  dhcpd lease 14400

  dhcpd ping_timeout 500

  dhcpd allow inside

  Please check the configuration, please correct me if I missed something. I'm in a critical situation at the moment...

  Please advise...

  Thank you very much...

  Where it fails at the present time?

  Can you share out of after trying to establish the VPN tunnel:

  See the isa scream his

  See the ipsec scream his

  Please also run the following debug to see where it is a failure:

  debugging cry isa

  debugging ipsec cry

• Doubt on the RA aaa using ACS 5.3 vpn user

  Hello

  I'm putting in place of the VPN on 8.4 ASA with 2 - VPNGp1 and VPNGp2. VPNGp1 groups users will access 1.2.3.0/24 and VPNGp2 users will have access to 5.6.7.0/24. User authentication will be done using RADIUS 5.3 ACS.

  On ASA, I configured pools VPN groups, ACL of VPN, IP, tunnel of groups and group for each group strategies.

  GBA, I created vpn-user1 and user2-vpn for each of the 2 groups.

  I don't know if some configurations more must be done on ASA and AC... Do I need to add new users - vpn-user1 and user2-vpn - on ASA, under each corresponding group policy, using the command political vpn-group?  Or I need to do something else on the ACS?

  Finally, how can I configure authorization and accounting for VPN users? I have to do this on GBA or ASA?

  Please advice.

  Thank you.

  Hello

  Authentication using radius aims to centralize user accounts and policies so that you will not have to configure these on the SAA. You must create a group of authentication servers that points to your ACS, then you will have to refer to this group of servers to your tunnel-group for user authentication queries will be forwarded to ACS for authentication. For accounting you will create an accounting server group and also assign to your tunnel group configuration.

  The GBA, you will need to create a network client that is ASA, and the shared secret will be the same. You create an element of authorization policy network who have the permission settings, or you can choose allowed access, which allows authentication succeed without any special authorization.

  You can debug the sessoin using crypto vpnclient 255 debugging to view the authentication stream.

  Using SSL vpn (anyconnect) for these sessions?

  Thank you

  Tarik Admani

• AnyConnect VPN Client on IOS router

  Hi guys, I configured AnyConnect SSL VPN on Cisco 2811 router. It works perfectly when I login via web and customer execution of secure mobility. However, when I connect directly from the mobility client connection fails. He does not even ask me user name and password.

  ----------------------------------------------------------------------------------------------------

  Mar 7 21:36:47.613: % SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: successful with SSL/TLS connection distance

  21:36:47.617 7 March: WV: sslvpn rcvd context process queue event

  21:36:47.621 7 March: WV: sslvpn rcvd context process queue event

  21:36:47.745 7 March: WV: sslvpn rcvd context process queue event

  21:36:47.749 7 March: WV: entering APPL with framework: 0 x 49233618,

  Buffer (buffer: 0x4925DA18, data: 0x3F57ED98, len: 1,)

  offset: 0, area: 0)

  21:36:47.749 7 March: WV: fragmented data App - stamped

  21:36:47.749 7 March: WV: entering APPL with framework: 0 x 49233618,

  Buffer (buffer: 0x4925D818, data: 0x3F2033F8, len: 242,)

  offset: 0, area: 0)

  21:36:47.749 7 March: WV: Appl. Treatment failure: 2

  21:36:47.749 7 March: WV: server-side not ready to send.

  21:36:47.749 7 March: WV: server-side not ready to send.

  21:36:47.749 7 March: WV: server-side not ready to send.

  21:36:47.753 7 March: WV: sslvpn rcvd context process queue event

  21:36:47.753 7 March: WV: server-side not ready to send.

  --------------------------------------------------------------------------------------------

  ====================

  Here is the config:

  =====================

  Crypto pki trustpoint VPN_TRUSTPOINT

  enrollment selfsigned

  Serial number

  name of the object CN = Academy-certificate

  crl revocation checking

  rsakeypair RSA_KEY

  !

  !

  VPN_TRUSTPOINT crypto pki certificate chain

  !

  local IP VPN_POOL 192.168.7.100 pool 192.168.7.150

  !

  WebVPN gateway VPN_GATEWAY

  IP address

  trustpoint SSL VPN_TRUSTPOINT

  Enable logging

  development

  !

  WebVPN install svc flash:/webvpn/anyconnect-win-3.1.02040-k9.pkg sequence 1

  !

  WebVPN context VPN_CONTEXT

  title ".

• What happens when I add the user?

  Hello

  I want to add a user. I think with administrator privileges.

  How is the Admin differs from the standard?

  It will have access to everything in the two? Fine.

  Nothing will change in appearance in adding a user?

  Excuse my stupidity, but it indicates a base folder will be created with his name. Is that mean a home folder as average with separate applications, desktop, Documents, films, records, etc.?

  best,

  Elmer

  It's for Yosemite, but the same information applies to El Capitan-> OS X Yosemite: Configure users on your Mac will explain the differences between accounts.

• Valid email required? Failed to add another user to the escan.

  Hi, my printer is HP Photosmart 7520

  I try to add a user who will be my work email address, I get to the Welcome screen, then asked to enter the email address, this is made of sinople carefully and then I get a message "Please enter a valid email address to continue.

  I have re set the settings, look for the updates and tried a dozen times.

  Any ideas very welcome.

  It's what I suspected. Your SMTP server for the email client you are using doesn't have the necessary safety requirement, or it has too many. Some areas would not meet the criteria to be used for this feature, unfortunately. This is probably due to a change in our standards or their standards. I don't know who. But the round of work more accessible is to use another area.

  I'm sorry for the inconvenience this might cause.

  -Spencer

  PS I hope you have a wonderful day!

• Add a user outside the administrator account

  original title: is it possible for someone to add a user other than Administrator account?

  Somehow an added to user accounts user account and it is not me the administrator?

  Hello

  What operating system is installed on the computer?

  You can create a new user account without being an administrator, but the account will not be a standard user account that has limited privileges.

  Hope that helps.

• Add the user to the users group in the Users.ini file using c#

  Hello

  Using a c# application, we strive to add/remove a user from the TestStand Users.ini file.

  The CreateDeleteUsers.seq file in the samples of TestStand is used as a reference.

  We have seen that we are able to add the user to the list of user help file

  engine. UsersFile.UserList.SetPropertyObjectByOffset (0, 0 x 1, newUser.AsPropertyObject ());

  However, when we try to add the user to the user group, the sample file CreateDeleteUsers.seq said

  RunState.Engine.GetUserGroup (Locals.GroupName). Members.SetPropertyObjectByOffset (0, 0 x 1, Locals.User.AsUser.LoginName)

  If we try to replicate this in c#, the API seeks the last parameter (which is LoginName in the CreateDeleteUsers.seq file) as an object of property

  engine. GetUserGroup (this.) GroupName). Members.SetPropertyObjectByOffset (0, 0 x 1, newUser.AsPropertyObject ());

  This causes an exception of object reference when we run the application.

  Please advise on how to proceed.

  Thank you

  Arun-

  The members property is an array of string, so the 3rd parameter to SetPropertyObjectByOffset requires a string property object, IE. the user name and not of the user object. From the will of the user object error with '-17308; Specified value is not the expected type. ». The example should really be using SetValStringByOffset to be clearer so that you only specify the user name of the actual string.

• Performance issuses, impossible to uninstall a program, add another user account, the computer doesn't turn off etc.

  Can anyone help, my vista home 32-bit edition computer is seriously messsed! ??

  I'm unable to download windows updates and I have like 20 of them to download, it just never performs an act he says its download, but it's not I can leave it for hours and nothing happens, this causes problems because my computer does now, because when you do it just says : configuration of updates and can last for hours, so I have to unplug the power to turn it off, which is not good for the computer.

  IM also having problems with other things such as it won't let me uninstall not more programs, I can't do a restore of the system from the control panel or add another user account. freezes Internet too much, slow start. I always get microsft popups saying: "the program has stopped working and not could find solutions to this problem" but I did a system restore in safe mode, but the dates were 3 months back and that didn't help the performance of this computer. I want to return to a closer date now, but I can't. as it doesn't let me do a restore of the system in the menu start control pannel ir.

  I run a scan with malaware had 181 made thereats that were deleted but I still have the same problems as above

  He said also my windows defender is not protected (outdated) more and needs to update, but it will not update

  Help, please

  Hi gandt85,

  1. you remember to make changes to the computer before this problem?

  2. are you able to boot into safe mode without any problem?

  Since you are not able to restore the system to normal mode, I suggest you to do a system restore to a recent date of WinRE using the full version of Windows Vista disk.

  Method 1:

  Do follow link below:

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Method 2:

  You can also try to run a scan using Microsoft Security Essentials.

  Check out the link:

  http://www.Microsoft.com/security/products/MSE.aspx

  Also, try the malicious software removal tool and check.

  http://www.Microsoft.com/security/malwareremove/default.aspx

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• You can select Add your ISP in your routing table

  Hi Tech support

  Ask a silly question

  You can add your ISP in your routing table, or is it just for subnets etc. to communicate to the outside world?

  In the affirmative. Can someone give me a link to do this

  I have a router MPS of 2691

  IOS is C2691-IPVOICEK9-M), Version 12.4 (25 d)

  Thanks in advance

  1 other question.

  Is implementation of a list of access via ip nat outside and inside of the only way to give devices internal internet access?

  Hi John,.

  Try this:

  Traceroute IP_ISP of your cme_router. If the first hop in the result table is your entry door and then nothing comes, maybe you should check the entry door.

  Concerning

• SNMP traps may explain PPPoE users on a router?

  For purposes of verification, I want to use SNMP traps to account for PPPoE users on a router?  I don't see a way to do this.  Is is possible?  If not, what is the best way to go about this?

  "Server enable snmp traps pppoe" is not providing this type of info, any more than I think it should anyway. OTOH, if you configure "accounting aaa" global or "ppp accounting" by interface, the NAS (your rtr) can report these modules to the server (RADIUS or GANYMEDE) AAA:

  rtr# show accounting
  

  Active Accounted actions on tty0, User (not logged in) Priv 1
  
      

   Task ID 1, EXEC Accounting record, 00:35:16 Elapsed
  
      

   task_id=1 service=shell
  
      

  Active Accounted actions on tty33, User ellie Priv 1
  
      

   Task ID 16, EXEC Accounting record, 00:00:17 Elapsed
  
      

   task_id=16 service=shell
  
      

  Active Accounted actions on Interface Async33, User tom Priv 1
  
      

   Task ID 17, Network Accounting record, 00:00:13 Elapsed
  
      

   task_id=17 service=ppp protocol=ip addr=10.0.0.1
  
  

  Then it's a matter of instrumentation of a solution on the AAA alert/report server however you want for the listeners. I think that SNMP trap would not be the first choice as a mechanism of benefit in this case, as there are a lot more simple options on a server.

  Alternatively, if you believe this info can be obtained with some show commands on the router itself and the router supports EEM, I'd want a solution based EEM on the other Network Management forum (https://supportforums.cisco.com/community/netpro/network-infrastructure/network-management), which can certainly generate an SNMP trap as a result.