Adding a new WAP browser home

Similar Questions

• Added the new computer but lost all favorite settings on old. I need new account keep different settings on both?

  My laptop (i5, running Win 7) is my workhorse computer that had all my favorite settings stored. I added a new office (AMD, Win 8.1) that will be used as a multimedia entertainment unit, but when I connected the cable to install FireFox it replaced all the settings in my laptop with the new computer. How can I keep the different settings on each computer? Must have 2 different accounts to be able to do this? I have now lost the web address for some of my sites, so it's quite painful. The "recently marked with a bookmark" folder is the main problem, because it is where I was monitoring my sites.
  Computer LAPTOP is Acer Aspire i5 & Win 7 runs the modules listed below.
  DESKTOP is a Medion with an AMD 3.8 GHz Turbo & Win 8.1, with the new version of the FF browser.
  Auto Firefox installed the same modules as the laptop, but I will change those & don't want to FF to automatically install the same on both computers. How can I separate them?

  See this - https://support.mozilla.org/en-US/kb/how-do-i-choose-what-types-information-sync-firefox

  You can only select favorite and maybe passwordsand uncheck other options of data type.

• Adding a new hard drive on e9180t

  Hi, I have e9180t and I'm considering adding a new hard drive.

  Can my office manage 3 to/6.0 GB/s 64 MB Cache SATA internal hard drive?  I get my full performance out of it?

  I read the possible combinations (http://support.hp.com/us-en/document/c01817977 specification page

  Is there a limit to the capacity of the hard drive?  (up to 2 TB)?

  Can handle a 6.0 GB/s transfer rate?

  I currently have 2 hard drives in the following:

  1 TB - Barracuda (st31000528as) 7200 RPM 32 MB SATA 3.0 GB / s
  500 GB - Maxtor DiamondMax 21 (STM3500630AS) 7200 RPM 16 MB SATA 3.0 GB/s

  If I buy 3 to/6.0 GB/s hard drive and use it as a hard drive, will I use these two hard drives as a secondary hard drives?

  Thank you!

  For those who might be interestd, this is what I found after some digging and calling:

  Since the motherboard that comes with e9180t (ipmtb-tk) is SATA 2, its speed is limited to 3.0 GB/s.   When 6.0 GB/s hard drive is connected, the speed will slow down to 3.0 GB/s.

  You can only use the full 3 TB capabity if your motherboard bios has opportunity to support UEFI interface.  However, most of the motherboards built before 2011 doesn't have this option.  ipmtb-tk is one of them.  However, there is a work around.

  1. go in the bios and check that the interface is set to AHCI (non-RAID).

  2. when the disk partition is loaded, you will be able only to the 2 TB partition.  another partition 750Go seems a separate partition that you cannot change.  Partition the 2 TB the way you want to and install Windows 7 on it.

  3. after that excavation is done, download Seagate Disk Wizard.  Later one of their homepage did not work, however.  You must download this one:

  http://www.seagate.com/staticfiles/support/downloads/discwizard/DiscWizardSetup-14382.en.exe
  

  I don't know why they don't have this default link on their home page when you go to download DiscWizard.

  Once the wizard disk is installed, it will pick up the 750Go that you weren't able to before partition as a new drive and now will allow you to partition.   (Keep the MBR instead of TPG setting, format it to NTFS)

  Once you partition using the tool, Viola!  a new drive with 750 GB of space has been added as a new drive.

• Error installing WAP browser - myapp - 1.cod 404 not found

  Hi all Experts,

  I am new to the BalckBerry Development.I have developed an application and have tested on Blackberry phone and Simulator.

  While testing on phoneI used BlackBerry Desktop manager to install the application on the phone. Now, I want to download from a wap browser and install on the phone so that one can install it. But I am getting following error when installing from the wap browser.

  "myapp - 1.cod 404 not found".

  I put the rest of files on the server

  1 myapp.cod

  2 myapp.jad

  3 myapp.csl

  4 myapp.cso

  5 myapp.alx (I used this file for installation using the BlackBerry Desktop Manager)

  Do I need to put any other file for this?

  When I debug it I found that my jad file contains sh1 signature for files myapp - 1.cod, 2.cod - myapp myapp - 3.cod.

  But I couldn't find the files above.

  Should I generate these files?

  If the cod file is greater then 64 k is a zip file. I use winrar in context menu. If all defective changes the extension zip and try it then.

  in the zip files are the Sub-Sub-cod-files, such as the cod-1, 2-cod etc.

• My MacBook Pro was built in mid-2009, I understand that I won't be able to get the next Sierra of OS.  I just put a new hard drive 700 GB, more I added a new battery to include a new CD/DVD drive.  I spent more than 400 million dollars. What I need to by

  My MacBook Pro was built in mid-2009, a 2.6 GHz, 13-inch, I just put a new hard drive 700 GB and I added a new battery to include a new CD/DVD drive.  I spent more than 400 million dollars.

  I understand that I won't be able to get the next Sierra of OS. I need to by a new Mac?

  Talk to the people the more I would get if I turn in I'd get is about are about $ 100 million.  Please tell me it isn't so.

  If you want Siera you will need a new Mac, but you can continue to use the old one as long as you want.

• I added a new apple ID. He continues to show former apple ID what me I forgot the password.  What should I do?

  I added a new apple ID. He continues to show former apple ID what me I forgot the password.  What should I do?

  Bought/downloaded content by one that Apple ID is linked forever, and in the case of applications will always require to update.

  Your best bet is to try to recover the password for it.  Go to http://iforgot.apple.com and try to get it back.

  If you forgot your Apple ID - Apple Support password

• Satilite M40X - adding a new processor

  I was wondering how I would go about adding a new processor in my laptop. I've never done anything like this before and I was wondering how I would go to do. Also, I still actually have to buy a new processor so if you have any suggestions, or if there are problems cause I should knowledge about it would be great if you could tell me.

  In your case, I won t exchange the CPU.
  It is not really important because the price of a new processor is high and you get much more performance.
  The BIOS does not always work with the CPU and Toshiba doesn't supports this service.

  I started an article on Exchange CPU/GPU:
  http://195.182.196.33/KB0/FAQ7A01ZW0007R01.htm

• RN104 - added 4 new 4 TB drives. 2.5 days of resynchronization. Start copying files, or wait until it's done?

  I think I've drunk mostly in the title...

  I just added four new 4TB discs (WD40EFRX) to a vacuum RN104 running the latest operating system. (6.4.0)

  At the start, he started a resynchronization estimated at about 70 hours.

  Is a resynchronization required on an empty set of disks? (If not, can I cancel?)

  If I have to re-sync, can I go ahead and start writing some stuff on the drive is Resyncing? (I'm willing to take whatever the performance hit, there could be.)

  Thank you!

  The synchronization is made at the level of the block of readers, even thoug hthey are empty, they still need to be resynced.

  If it's critical to copy the data across, you can start adding data while resynchronization is in progress. Although you will take a significant performance hit, synchronization and the writing speed. AND, you won't have the advantage of reduncancy until the end of the resynchronization.

  Unless it's critical data, my suggestion would be to wait until the Resync is finished, and THEN copy the data across.

• Added the new kingston 256 GB ssd to my MBP 13 "2012

  I added a new ssd 256 GB kingstone to my MBP 13 "2012 and it worked fine for a month, today it has frozen and restarted without reason. and there is a folder with a questionmark in the middle of the screen icon. I once git to start again and now it stoped working again. Can any ideas on how I fix this?

  You can contact the manufacturer and see what are the provisions of the warranty.

  Start the recovery partition and run disk utility > first aid.

  If there is no problem, remove the SSD and install it in a closed Chamber.  Plug it into the MBP via USB and see if it will start the MBP.  If so, the internal SATA may have to be replaced.

  Ciao.

• Salvation; I instaled a new Windows XP Home edition on my computer hp laptop, but it's not conect to the internet through my wireless card.how can solve this?

  Salvation; I instaled a new Windows XP Home edition on my computer hp laptop, but it's not conect to the internet through my wireless card.how can solve this?

  Did you use the recovery process HP plant or install using a different operating system disk? If the latter, you need to install the drivers for all your hardware, including drivers for wireless network cards. You will get only the pilot specific support for your laptop model HP Web site tech.

  If by "wireless card" you mean that you have a 3G USB modem through your cell phone provider, contact the cell phone provider for help with that. MS - MVP - Elephant Boy computers - don't panic!

• brand new windows 7 Home premium backup problem

  Hello

  I bought the new HP pavilion DM3 [external dvd player] with the new windows 7 Home premium intalled about 4 weeks ago. After the first round and all updates installed, real I tried windows backup on dvd - r media.

  I started windows backup, after whereas it wonder average wiriteable so I put the dvd - r inside, next step was to format dvd - r [little unusual, but I have no choice]... After succesfull formatting it starts to burn. After a few hours, he was still burning mode 54% without errors and progress too. I pull out the cable of the external dvd burner, the writing process has failed and on dvd was written about 1 cm of layer thickness.

  I tried 2 times again with the same result, but the different progress of burning 56% and 25%

  What should I do?

  Best regards...

  Hello D.A.E.Z.,

  Please check the site for problems with CD/DVD problems.
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  There is an automatic FIXIT who might help with your problem.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Citing a WAP browser on OS 7 (via BrowserSessionFactory)

  Our code is based on article "Invoke the browser."

  http://supportforums.BlackBerry.com/T5/Java-development/invoke-the-browser/Ta-p/445362

  On OS7 device BrowserSessionFactory cannot browser WAP - the reason for this is that the following code:

  if( myRecord.isValid() &&
      !myRecord.isDisabled() &&
      (myRecordHelper.getConfigType() ==
      ServiceRecordHelper.SERVICE_RECORD_CONFIG_TYPE_WAP2)
      && (myRecordHelper.getNavigationType() != -1))
  {
      uid = myRecord.getUid();
      break;
  }
  

  is not triggered because myRecordHelper.getNavigationType () returns-1.

  Here's the WAP2 folder properties in the maintenance book

  myRecord: WAP BrowserConfig[WAP BrowserConfig]
  myRecord.getUid: WAP BrowserConfig
  myRecord.isValid: true
  myRecord.isDisabled: false
  myRecord.getNavigationType: -1
  

  If we remove the "!" = - 1' check, the factory can detect and open the WAP browser
  (but this change has probably some other side effects)

  Can someone rim please look into this and let us know what is the good
  way to open a WAP browser on device 7 OS?

  Thanks Mark!

  We cannot test the BES browser now, I suppose that we can do a similar check one done for TransportInfo.TRANSPORT_BIS_B?

  We have also two different solutions when WiFi record returns isDisabled - is the difference between them? Can I keep one of them (and where?)

• Class not found exception after adding a new image in the folder resources.

  The app works perfectly well on the Simulator and the device. After adding a new set of images, he began to show in every race, on the Simulator and the device, a class not found exception.

  When you try to delete some images to find the cause, I get different classes not found when executing. Compilation and packaging the application generate warning or error. They even get signed. Some of the classes are not exception I get:

  Java.lang.StringBuilder

  NET. RIM. Device.API.UI.UIApplication

  I'm guessing this has something to do with the size of the total image, since the size of each range image from 100 KB to 300 KB, and we talk about only 25 or 30 images in total. Adding image outside of the 'res' folder does not generate the error, but the image is not added to the final files.

  In addition, this application is not large, but when compiling and packaging of the app, it generates and signs 125 cod files. Is this normal?

  I use Eclipse 3.6 (Helios) and BB SDK 5.0.0.25 won win 7

  Any help will be appreciated. Thank you.

  Have you seen this?

  http://supportforums.BlackBerry.com/T5/testing-and-deployment/the-maximum-size-of-a-BlackBerry-smart...

  I would recommend that you download these kinds of resources and put them on the SD card if you take a storage capacity that users will want to keep available for email and others.

• Error when adding a new section with SQL in application websheet

  Get the following error while adding a new section with inside on an existing page SQL query in websheet request.

  ()This is the first time I tried to add a SQL query to an article in a websheet. Is that suppose to work?)
  
  

  

  You can see that access SQL and PL/SQL is already enabled for this application websheet.

  
  

  

  After trying many things, I found the 'access SQL and PL/SQL' must be enabled at the level of the APEX INSTANCE also.

  This is how to do it:

  (1) connect APEX as a forum admin with the following credentials:

  workspace: internal

  user ID: admin id defined during the installation of the apex (usually, it will be admin only)

  password: admin password set during the installation of the apex

  2) click manage the Instance > feature Configuration

  (3) select Yes to enable access SQL in Websheets

  

• Adding a new license for a new Member, but may not use programs. Saying licensing issues... any advice?

  Adding a new license for a new Member, but may not use programs. Saying licensing issues... any advice?

  You use the Enterprise Dashboard?

  If so

  1. ensure that they use the correct ID type. So if they have been added to the dashboard with Enterprise or federated ID to ensure they do not use the Adobe ID or vice versa.

  2. bring to sign out and sign back in to check their eligibility.

  3. If the problem persists, then try this:

  The opm.db file contains the login user cached information and delete this file is a useful troubleshooting step. Once deleted a fresh file will be automatically created when you start creative cloud and reconnect.

  1. Close the creative cloud application.
  2. Navigate to the OOBE folder.
     Windows: [system drive]: \Users\ [user name] \AppData\Local\Adobe\OOBE
     Mac OS: /Users/ [user name] / folder/Library/Application Support / Adobe / OOBE
  3. Delete the file opm.db.
  4. Launch the creative cloud.