Addition of LaserWriter 4/600 PS

Similar Questions

• HP ENVY PHOENIX CTO 810-135QE - 600 watts power supply Question

  In the near future, I would like to upgrade the video card in my desktop HP ENVY PHOENIX CTO 135QE-810 GT 640 default to something a little more powerful and I was wondering if there is any details about the default 600 watts power that will help me in my decision to the next video card.

  I know that some video cards require a number of amps on the 12 volt rail and all the information that I have found previously on the power of 600 watts power supply in the computer is not in that kind of detail.

  What I read, the power is a Petrus 600W e-star 5.0 Bronze, HP Part number 633186-002.

  Any additional details and details on this power to help me determine the next video card would be useful.

  On a side note the video card, I'm currently doing is one of the next Nvidia GTX 750 TI models, thoughts and recommendations on this specific map?

  Thank you

  JCOOPER2

  Hello

  Your PC has UEFI bios, so most video cards should work.  Some video cards will work in UEFI mode and others in legacy mode, that your PC is able to run.

  When the manufacturer of the video card and/or AMD or NVIDIA specify a minimum power supply size then it is best to stick to this recommendation.  Not all power supplies are built to the same standards of quality.  In addition the internal components, temperature, charges unknown and time that the PC will be placed under the maximum load are taken into account at the recommendation of minimum power supply is indicated.

  I have not seen a power of 500 watts with 12v rating of 18A, but this does not mean that there is not. And if that's the case, then the total power rating is suspect. A video card that requires an external auxiliary power connector will also draw power from the PCI-E slot.

  Are there cases where the minimum size of the power supply is insufficient? Yes, those who might be extreme but someone can have connected to power different connectors either to avoid buying a new power supply or maybe around just the food manufacturer minimum power rating. Some may do it thinking 'I'm going on fox the Fox ". It can work, but maybe the questions later start occurred.  I prefer to get the job done right the first time. You don't need a power supply to perhaps of overload and short circuit then internally causing spikes to the components in the PC.

• Battery not be dependent not on PRS - 600

  Hi all, I received a PRS - 600 (renovated) woot.com a week or two before, and unfortunately it will not load.

  Here's what I've tried so far:
  -plugged the drive on a laptop USB, with two different cables (at night). The laptop didn't see USB used, and the player remained empty, with no charge light.
  -plugged the player in an AC-> USB adapter and has left there for the night. The detected drive is plugged in a USB port, but it does not keep a charge.
  -plugged the player in a PSP adapter and has left there for the night. The reader could be activated and used, and there was a Flash by the symbol of the (empty) battery in the lower left and no charge light. When I unplugged the PSP adapter, there is no charge, and the player could not be turned on.
  -plugged the drive into a PSP adapter AND laptop USB at the same time (and all night). The detected laptop could interact with the player (I put a book on the subject), and the player said that a USB drive is connected. There was a lightning bolt symbol too, but when I unplugged the adapter PSP, laptop thought that the drive has been disconnected. The drive could not be activated after the PSP adapter has been removed.

  If anyone knows of another solution that would work I could have tried, please let me know! Or I send to Sony for repair?

  After the purchase of 4 different AC - USB adapters, I finally called Sony. The player seems to load, but was not. Low and behold, they told me that you can not load the PRS-600 with an AC - USB adapter. The USB charging can only be performed from a computer. To reload the computer from the wall, you can buy an adapter that plugs into the small yellow hole at the bottom of the player. In addition, I remember reading that you can't load a laptop which is plugged on the wall or in mode 'sleep'.

• Adding SSD to ProDesk 600 SFF: where can I find the good material facility?

  I bought the MFS 600 ProDesk. I want to add an SSD in the Bay 2.5 "and keep the hard drive 3.5".

  Read the service manual installation on a 2.5 drive ", page 121 said 'Install four black and blue isolation mounting guide screws M3'.

  The manual says:

  "NOTE: metric M3 isolation mounting guide screw can be bought from HP."

  Questions about the addition of the 2.5 "to a ProDesk 600

  1. How can I get these HP?

  2 are the sons of these screws compatible with most SSDS, more precisely from Samsung?  I have read conflicting information on the web (wow, contradictory information on the web? "It's shocking!)

  3. if HP screws are owners somehow, screws which can be used with standard SSD (thread and length, please)?  (I'd be happy to buy one of the SSD that HP sells on its Web site, but their prices are not compatible with other units currently available by a factor of at least 50%)

  Thanks in advance for suggestions and answers

  Ok.

  SSD drives are shock resistant. Which makes them very unlike electromagnetic inherited from hard drives, which can be destroyed easily by being moved or deleted.  That's why a lot of people just use tape double sided.  It is a solution of Occam.

• HP Prodesk 600 G2: HP Prodesk 600 G2

  Hello

  I have big problems with HP prodesk 600 machines of g2.

  They do not read the bios hard drive, new pushed hp which correct the error that its still there.

  After a few days the pc recognized hdd.

  We have more than 50 of the machines and it's a big problem for us.

  If anyone has any info please post it here.

  Thank you

  In addition, u cant new stable operating system from cd or a USB drive during the instalation to get to the point where u chose language it freezes, its verry frustrating.

  Thanks in advance.

  the new Skylake Intel processors have architectural changes to the way that USB is supported and the new implementation is not supported in Windows 7

  NOTE: creation of ISO and ability of DVD burning software are necessary to complete this process.

  1. Create an ISO from a DVD of Windows 7 OS image file
     a. Insert the Windows 7 DVD in the DVD drive.
     b. open the ISO creation software.
     c. create a picture ISO of DVD Windows OS file.
  2. Create a temp "folder on the HARD disk and copy all the files from Windows 7 image in the folder"
     For example. c:\Temp
  3. Create a folder called wim' under c:\
     For example c:\wim
  4. Copy the install.wim and boot.wim , files located in the folder c:\temp\source\ to c:\wim.
  5. Download and install the Setup Kit automated Windows for your specific operating system version
     Windows 7:

     Windows Automated Installation Kit

  6. Start the AIK with administrator rights deployment tools command prompt:
     a. search 'Deployment and imaging environment tools' in the Start Menu.
     b. right-click and select run as administrator.

  7. At the command prompt, replace the c:\wim location, command:
     CD c:\wim
  8. Create a directory under C:\wim called "mount", command:
     c:\wim > mkdir mount
  9. Mount the WIM image with write permissions, orders:
     For the 32-bit operating system:
     c:\wim > imagex/mountrw install.wim 5 c:\wim\mount
     For the 64-bit operating system:
     c:\wim > imagex/mountrw install.wim 4 c:\wim\mount
  10. Add the install.wim image USB3.0 pilots, orders:
      For the 32-bit operating system:
      c:\wim > cd c:\usb3\x86
      c:\USB3\x86 > / image: dism/Add-Driver driver:c:\USB3\x86 C:\wim\mount / recurse /forceunsigned
      For the 64-bit operating system:
      c:\wim > cd c:\usb3\x64
      c:\USB3\x64 > / image: dism/Add-Driver driver:c:\USB3\x64 C:\wim\mount / recurse /forceunsigned
  11. Save the WIM image with new drivers disassembly and validation, the command:
      For the 32-bit operating system:
      c:\USB3\x86 > imagex / disassembly / commit C:\wim\mount
      For the 64-bit operating system:
      c:\USB3\x64 > imagex / disassembly / commit C:\wim\mount
  12. Add the USB3.0 driver to two facilities boot.wim with the following steps, so that the drivers will be available during the installation.
      a. adding a driver in boot.wim 1
      i. Mount the boot.wim image 1 with write permissions
      For example c:\wim > imagex/mountrw boot.wim 1 c:\wim\mount
      II. access to the directory where the drivers USB3.0.
      For 32 bit OS: c:\wim > cd c:\usb3\x86
      For the 64 bit OS: c:\wim > cd c:\usb3\x64
      III. Add the USB3.0 Drivers (.inf) file to the boot.wim image base 1
      For the 32-bit operating system:
      c:\USB3\x86 > /add-driver/driver:./recurse/image: C:\wim\mount dism
      For the 64-bit operating system:
      c:\USB3\x64 > /add-driver/driver:./recurse/image: C:\wim\mount dism
      IV. unmount the boot.wim image 1
      For the 32-bit operating system: c:\USB3\x86 > imagex / disassembly / commit C:\wim\mount
      For the 64-bit operating system: c:\USB3\x64 > imagex / disassembly / commit C:\wim\mount
      b. Add pilot Boot.wim 2
      i. Mount the boot.wim image 2 with write permissions, command:
  
  c:\wim > imagex/mountrw boot.wim 2 c:\wim\mount
  II. access to the directory where the drivers USB3.0.
  For the 32-bit operating system: c:\wim > cd C:\USB3\x86
  For the 64-bit operating system: c:\wim > cd C:\USB3\x64
  III. Add the USB3.0 Drivers (.inf) file to the boot.wim image base 2
  For the 32-bit operating system:
  c:\USB3\x86 > /add-driver/driver:./recurse/image: C:\wim\mount dism
  For the 64-bit operating system:
  c:\USB3\x64 > /add-driver/driver:./recurse/image: C:\wim\mount dism
  IV. unmount the boot.wim image 2
  For the 32-bit operating system: c:\USB3\x86 > imagex / disassembly / commit C:\wim\mount
  For the 64-bit operating system: c:\USB3\x64 > imagex / disassembly / commit C:\wim\mount
• Copy time install.wim and boot.wim to c:\wim in the c:\temp\source\, replacing the original files.
• Burn the files to a new DVD (make sure that the DVD is bootable) or create the image on a flash USB (UFD) drive.
• Install Windows 7 as usual. After installation, Windows 7 will have the USB 3.0 correct and functional drivers.

• Satellite M30-801: CPU only works with a 600 MhZ

  Hi people, I have a strange problem since my PC back to toshiba support (lcd problem, on assistance report i red that the pcb has been replaced): my CPU goes up to 600 MhZ. I tried to update the version of the bios from 1.20 to 1.70 successfully and I have restored the default value believing it could be a related problem of bios , but nothing changes.

  The problem is present in a new installation of Windows XP (from recovery CD), so I think I could exclude a software problem.

  Any ideas?

  Thanks in advance
  Roberto

  Hello

  The update of BIOS does ' t solve this problem.
  It seems that the Toshiba service partner forgot to start several compatibility tests. This is necessary after some repair procedures. Without this additional test, the CPU does not work with maximum efficiency. Well, there is nothing to see. You must contact the service again and it should solve this problem.

• Printers Multifunction LaserJet 600: Laserjet MFP - tray 2 600 do not lift

  So I have a printer Laserjet 600 who repeat his tent raised tray 2 assumed that the engine is down I just here for an overview see if there is anything else I can do. I passed on trays just to make sure that it is not this, but still the message happens.

  Does anyone else have this problem? You can simply replace the engine? or does go deeper then that as a control on board is no longer sends the data to activate it?

  The number on the left indicates the number of page when the error occurred, the number on the right is the error code.
  
  In this case, your number of pages current is probably higher than the numbers on the left, which means that those who are the old codes and have nothing to do with the current problem.
  
  I just faked the problem on the M602, I removed the tray, determined which finger came out of letter size paper which is the middle finger.
  
  Then I reached in and pushed the switch from the Center to the bottom so that the printer has been trying to raise the tray and after about 10 seconds, he got an error 60.02. I repeated the process twice, in an interesting way, the first time that I had not seen the error immediately, I had to push the home button to access.
  
  I work under the assumption that your machine is not any additional trays under tray 2.
  
  At this point I would replace the DC controller, but I have a spare for troubleshooting if that would make it easier for me than for you.

• Fixing additional monitor

  I want to fix my HP 2709 monitor to my HPTouchsmart 600.   The monitor has only vga not cables not a usb key, so how can I do?   Thank you

  Looks like you will need to get a USB-to-Video feature.

  Here is a decent one for about $40 on amazon:

  http://www.Amazon.com/Generic-USB-2-0-multi-display-adapter/DP/B001NG8H9G/ref=sr_1_sc_2?s=electronics & ie = UTF8 & qid = 1334974913 & SR = 1-2 - Spell

  When you plug into a USB port on your Touchsmart computer it will basically turn it into a connection to your second monitor.

  Some people have commented that plug a USB-to-Video device can cause your tactile feature Act up.  If so, disconnect the USB-to-Video device should stop.

  Since you already have a VGA cable, you don't need to buy additional cables, but you will need to use the adapter DVI / VGA provided with this unit I linked to the top above.

  I hope this info helps!

• Satellite Pro P100: external display connected to DynaDock uses 800 x 600

  I have a P100 SatPro attached to a monitor external 19 "via a Dynadock.

  By default, whenever I start the laptop the screen resolution 800 x 600.
  I have to manually reset to my desired resolution (1280 x 1024, 32-bit colors).
  If I reboot at any time the resolution then default back to 800 x 600.

  It's driving me crazy! Why won't save the settings? I tried to reinstall the software with no joy.
  Operating system is Windows XP SP2 and I'm a full administrator.

  Any help or ideas appreciated.

  see you soon
  Ian

  Hello

  I m not 100% sure if this might help you, but I noticed a similar problem on the Tecra M4 anchored to the multiple dock Tablet.
  The update of the BIOS helped solve this problem.

  In addition, an update of the graphics card driver would be desirable.

  Good luck

• Update your TouchSmart 300 or 600 software to version 4!

  HP has released updates of software that allows you to have the same software used on TouchSmart 310 and 610 models. It takes a while, but I've updated successfully a TouchSmart 600-1050 and it seems to work very well.

  There are a few pretty cool additions... the biggest change is to the "canvas" TouchSmart... how you can use the software to interact with your photos, programs and notes.

  There are two methods that you can use to update... ((1) you can download all the files yourself and run separately or the 2) you can use HP Support Assistant and do automatically collect and download all the files (except the Activator - who must come first).

  The most important thing is that you must first download the activation software. If you do not download the software enabler - HP Support Assistant or the other files may not work.

  Here is the document of support for HP who offers the links to the files, and explains how do:

  Updated TouchSmart 3 to 4

  I published an all-in-one update to the TouchSmartDevZone.com tool. This tool simplifies the upgrade and installation process for those who want the TouchSmart 4.0 on their system software. The download link is: http://www.touchsmartdevzone.com/download/4070/TS4Upgrade/

  You will need a zip file tool to unzip the download. Windows has such a tool built starting with Windows 7. For other versions, I usually recommend using 7 - zip, an excellent free tool.

  Note that the tool is provided as-is without support of HP. use at your own risk.

• All written in Spanish? I have an IPhone 6. I'm traying, as I did in the past, my photos and videos from my phone to my laptop. I have done several times before. Today, he finds only 8 pictures when I have 600 ¡TKS for your help

  (1) I'm trying to transfer my photos from my IPhone to my laptop I did before. This time, my laptop only locates 8 IPhone 6 photos when I have about 600 on it (a long journey, long illness and recently became the only grandfather done I took this time so long this time).

  I tried to send back their of my IPhone in the mail of the laptop. In addition, to be a long waste of time, my photos arrive without order of photo I took, which makes very difficult to reorganize in the correct order, I took them. I don't know how to solve. I'm doing the right to 'synchronize' I tunes and my mobile.

  Pls help

  (2) in addition, I have another type of problems with my IPhone 6. I went this morning official Apple personal assitance but they offer me to do this here. "We only repair, but not fix softwore problems?" ¿ ?).

  I had 300 songs. Normally, my average photo stores about 150/200. Free space available aprox. : 2 GB (16 GB per device, 11 actually). Suddenly, there are a few days my started devide "complain". Says that space is not available. It's true that I increase my photos and videos to about 500. I deleted 225 songs. Now I have 3 GB of free space, although the device appears 4.5 GB occupied by "documents and data" and 1.5 as 'other '. I don't know what that means. I only keep photos, videos; I reduced the nr. space music and I hold not spam, and my APP aren't too 1.94 GB. How do I check the documents, data, and 'other' to delete and protect a lot more space?

  Sorry for my bad English. Pls if you're the kind to answer me, to make 'short and sweet', I mean, not only not too sophisticated. If you spoke Spanish... bingo

  My name is Jose Luis (Barcelona) - SPAIN - my name on this "support" under "jlhbcn".

  2016.1.7.

  Hola José Luis.

  Option 1: If tus fotos estan sincronizadas via iCloud:

  1. In el ordenador abre page web icloud.com
  2. writes you cuenta clave is the Apple
  3. ve al apartado fotos, ahi estan tus fotos, select a grupo senalando the phrase "seleccionar momento" that appears al pasar el raton sober una foto arriba has the derecha del grupo, you can add a una por grupos o una fotos
  4. en the part the pantalla in azul select download Arriba
  5. If borras las fotos descargadas is borraran en you iPhone también

  Option 2: sacar las fotos con a computer via iTunes:

  1. Conectas el iPhone al ordenador con iTunes
  2. IPhone iTunes pinchas el iconito del, ahora los apartados clamp ves en y e device
  3. Clamp en, pinchas en fotos, aqui puedes seleccionar una vidéoconférence caspula del ordenador y synchronise photos
  4. Dale al boton synchronise y las fotos is copiaran a dicha vidéoconférence

  Por defecto viene the fotos del ordenador, pero esto hara vidéoconférence what copien photos haya dentro al movil, por eso are mejor usar una vidéoconférence caspula.

  Los datos estan las applications dentro, y is pueden clear desde cada application, for example if walked in a group of whatssapp y borras the conversation y las fotos, will dropping el espacio as space watssapp. Desinstalando the application.

  In el iPhone, los use settings/general/storage y iCloud, puedes ver as space cada application + sus datos use in Storage manage Québec Hay el arriba, y el manage storage of abajo lo are using iCloud.

  Espero ayuda sido acercado

• 600 proDesk: power failure of HP

  I have a HP computer 600 ProDesk brand new I am trying to Setup. I press the power button and the flashes for a few seconds then back off and loops new throught he same process. I confirmed that the fan is running when the computer tries to turn on.  In addition, I replaced the power supply, but with the same problem. I don't hear any post beep errors during the current loop. Anyone have any suggestions on how to fix this? Thank you.

  @TECH1200

  Reinstall the memory.

  REO

• Remove cover Acer Aspire card mother z3 - 600 thermal shield

  Remove cover Acer Aspire card mother z3 - 600 thermal shield to upgrade memory

  I have an Acer Asipre Z3-600-UB16 and that you need to upgrade the RAM, but need to Remover the heat shield covers on the motherboard / RAM.

  I have already pulled the rear plastic cover, stand, removed the hard drive and the accessible screws that hold the screen cover / heat on the mother/RAM card.  It seems that additional disassembly is necessary, but there is absolutely zero information on the internet or even Youtube disassembly of this unit and nothing available for a repair or even simple images or patterns.

  Does anyone have video or written documents showing the additional steps on the removal of the cover (or heat shield) for the motherboard / RAM. Worst case, may have to cut a hole in the metal cover to get to the RAM/memory.

  Hello

  1. Remove the battery:
     Remove 1 screw from the battery door
     Lift the top edge of the battery holder
     Lift to remove the battery holder

     

  2. Remove the shield of the motherboard:
     Remove the 10 screws on the shield of the motherboard
     Lift the lower part of the shield of the motherboard
     Push the shield of the motherboard before the release of the fins of the heat, lift to remove the shield.

     

• Z3-600 thermal shield cover card mother Acer Aspire

  I have an Acer Asipre Z3-600-UB16 and you need to upgrade the RAM.

  I have already pulled the rear plastic cover, stand, removed the hard drive and the accessible screws that hold the screen cover / heat on the mother/RAM card.

  It seems that additional disassembly is necessary, but there is absolutely zero information on the internet or even Youtube disassembly of this unit and nothing available for a repair or even simple images or patterns.

  Does anyone have video or written documents showing the additional steps on the removal of the cover (or heat shield) for the motherboard / RAM.  Worst case, may have to cut a hole in the metal cover to get to the RAM/memory.

  I took a lot of pictures so far...
  Thank you.

  Remove 22 screws from the plate.

  

  Exit tank bezel LCD low hooks database. Lift the lower edge of the plate.

  Both sides

  

  Get out the base of the upper hooks of bezel LCD tank. Lift to remove the base plate passing the LVDS cable and touch the cable through the holes in the plate.

  

  Be careful with the plugs and cables

• HP Officejet Pro 8500 Wireless does not parse better than 600 dpi

  I searched and found a lot of similar complaints.

  Integrated display HP can only analyze up to 600 dpi, while the specification specifies 4800dpi with possibility to increase up to 19200 DPI. Then I went to get the 4 800 DPI 600 dpi is ugly to analyze detailed pictures.

  On the web, I found similar complaints and the indication that the HP Solution Center installation allows you to select higher resolutions on the PC which cannot be selected on the printing device itself.

  I don't have a Solution Center then downloaded the latest drivers and reinstalled the printer. HP Solution Center appears to be installed as well, although clicking it leads to an error to complete installation of the printer. I tried to reinstall with the addition of a printer icon: everything looks OK, printer is on an 802.11 wireless network, but after you find the printer, the last message is always "printer setting failed" (is actually in Dutch: "het instellen van printer is mislukt".)

  The strange thing is that printing is not actually a problem (on the wireless), or scan to email.

  I downloaded HP Print next and doctor Scan and the printer works perfectly (prints the test page), but the Solution Center still gives the message that it can not start due to an incomplete installation of the printer.

  I played with the firewall, turn off Norton360, Windows firewall and firewall router and then put it back, but the problem remains.

  In conclusion: it seems impossible to get the famous 4800 dpi.

  Someone knows the way out?

  Thank you

  It looks like something has not installed right. The best thing to do is rub the software of the printer to the computer using the integrated printer cleaning brush. The steps below will guide you in the process.

  Starting a download:

  1. run the disk cleanup on your computer

  2. download and run the software and the drivers below.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-88604-2&cc=us&DLC=en&LC=en&OS=4063&product=3752459&sw_lang=

  3. once the download is done retrieve, cancel the download.

  4. click on the start menu.

  5. click on run.

  6. type %temp% enforcement

  7. Locate and open the folder starting with 7z (example: 7zS2356)

  8 open the Util folder

  9 open the CCC folder

  10. run the L4.bat uninstall_ for computers not HP.  For HP computers, run the Uninstall_L3.bat

  11. once the uninstall is complete, restart the computer

  12. access to the files program and program (x 86) and delete all records that relate to the software of the printer.

  13 install an Accessories\ System Tools Disk Cleanup

  14. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  15. use this tool to clean the system and the registry.  Note: This utility is not HP sponsored or approved.  HP and I are not responsible for damage or loss of data caused by the utility.  This step is optional.   You can skip if you want.

  http://download.CNET.com/advanced-SystemCare/3000-2086_4-10407614.HTML?part=DL-6271865&Subj=DL&tag=button

  16 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-88604-2&cc=us&DLC=en&LC=en&OS=4063&product=3752459&sw_lang=

  17 run the download to reinstall the printer