After decryption of FileVault, MacBook could not start

Similar Questions

• Today my Macbook Pro could not start.  He showed me the ban or no symbol.  I was able to access disk utility and run first aid on the SM0256G of SSD Apple media successfully.  Cannot start in normal/safe mode.  Should I delete/install so I can?

  MacBook Pro 13 '' end 2015.  256 GB SSD drive. El Capitan last version 10.11.4. I turned on the Macbook Pro and it could not start.  The progress bar with the Apple Logo would be present but would end not showing the symbol «»  I tried to boot mode safe - no go.  I have not reset PRAM help.  I was able to access disk utility and run successfully the first aid. No help. I was unable to restore two separate backup.  The utility show me backups however when I would go to the next screen and no backup is available.  Disk utility displays the SSD.  Can I erase the disc and download OS X install?  Thank you.

  At this point, there is no need to delete. A new copy of Mac OS X can be installed directly over the old copy. This process replaces the components of Mac OS X on a file by file basis and adds missing ones, there will be no major throwing away what anyone, unless there is a power failure.

  You have already run disk first aid.

  Now use mode of recovery (command + R to start) to "Re-install Mac OS X. It should install the latest revision of the main version that you ran last.

• Want H8-1534: could not start HP Envy H8-1534 pc after Windows update 10, 1607

  Windows 10 has made automatically update 1607 (KB3176936) on the pc of my wife (HP Envy H8-1534) about 6 days ago. Since then I could not start the pc the first time I turn it on.

  When I hit the power button on the monitor lights up with the HP logo on black screen as usual but the loading icon (spinning points) does not start. Fans start, but there is no activity on the Tower in the way of flashing lights or beep sounds. If I turned off the pc by using the power button, wait 10 seconds and turn on again, the pc will start up as normal. So far, for the last 6 days, it took the 2nd attempt so that it starts the pc every time. It almost seems as if there are not able to go to the system except for the fans in this first attempt to start.

  I ran a test at startup by pressing the F2 key without no problems found. I disabled the SATA power management in the BIOS. I ran the Windows startup with no result repair. Here are the results of the txt file.

  I researched all the possibilities. I fear that this could begin to worsen. Any help will be appreciated.

  Name: Target OS Test
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 265 ms
  The test is performed:
  ---------------------------
  Name: Checking content Volume
  Result: Completed successfully. Error code = 0 x 0
  Setting time = ms 2391
  The test is performed:
  ---------------------------
  Name: Diagnostic Boot manager
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 63 ms
  The test is performed:
  ---------------------------
  Name: Diagnosis of the system startup log
  Result: Completed successfully. Error code = 0 x 0
  Time = 0 ms
  The test is performed:
  ---------------------------
  Name: event log diagnosis
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 62 ms
  The test is performed:
  ---------------------------
  Rated: Internal audit of State
  Result: Completed successfully. Error code = 0 x 0
  Time = 0 ms
  The test is performed:
  ---------------------------
  Name: Start-up condition Test
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 31 ms
  Root cause found:
  ---------------------------
  State the start indicates that the OS booted successfully.
  ---------------------------
  ---------------------------

  DBHPENVY,

  I turned off quickly startup on the pc and until now he started first try twice. I'll let you know how it does after a few days of testing.

  I read everything it does and it is perfectly logical, how it might affect our pc is the way. Go to this link and read about it and see if she could help. I thought I had turned off fast start already, but after an update he might have gotten turned on.

  Here is the link: http://www.tenforums.com/tutorials/4189-fast-startup-turn-off-windows-10-a.html

• I closed my laptop (Macbook pro 2012) screen with a day and immediately after 30-40 minutes his does not starts once again.

  I closed my laptop (Macbook pro 2012) screen with a day and immediately after 30-40 minutes his does not starts once again.

  Hello Varshil07,

  Thank you for using communities of Apple Support.

  If I understand your message, by updating your Mac you have forced stop, or you have closed the lid, and now it does not start.  To start, I suggest that try you to start in safe mode by following the instructions below.  For later use, it's a good idea to not force the computer to shut down or close the lid while it is up to date, because it can cause problems.

  1. Choose the Apple menu > shut down.

  2. After your Mac stops, wait 10 seconds, then press the power button.

  3. As soon as you hear the startup tone, hold down the SHIFT key.

     You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.

  4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

  To exit safe mode, restart your Mac, but no press during the startup.

  OS X El Capitan: start in safe mode

  Have a good.

• most programs now get error message "could not start from this location after a mail there is session 2 nite".

  After a session 2 nites E-mail there, many programs said message error "could not start program from this location. In addition, long delays after you clicked on a link, a large display hourglass for up to several minutes. Have tried to rebuild, but I think that the problem is still there. Any suggestions?

  What is a "mail session?

  What is, "have tried to rebuild?"

  Edition with Service Pack of Windows XP _ _?

  What anti-virus application that you use, and if she slept in day?

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find.  Reboot when necessary.  (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  The less you have to run all the time, most things you want to run will perform:

  Use Autoruns to understand this all starts when your computer's / when you log in.  Look for whatever it is you do not know using Google (or ask here.)  You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory.  This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  Do a house cleaning and the dust of this hard drive:

  You can free up disk space (will also help get rid of the things that you do not use) through the following steps:

  Windows XP should take between 4.5 and 9 GB * with * an Office suite, editing Photo software, alternative Internet browser (s), various Internet plugins and a host of other things installed.

  If you are comfortable with the stability of your system, you can delete the uninstall of patches which has installed Windows XP...
  http://www3.TELUS.NET/dandemar/spack.htm
  (Especially of interest here - #4)
  (Variant: http://www.dougknox.com/xp/utils/xp_hotfix_backup.htm )

  You can run disk - integrated into Windows XP - cleanup to erase everything except your last restore point and yet more 'free '... files cleaning

  How to use disk cleanup
  http://support.Microsoft.com/kb/310312

  You can disable hibernation if it is enabled and you do not...

  When you Hibernate your computer, Windows saves the contents of the system memory in the hiberfil.sys file. As a result, the size of the hiberfil.sys file will always be equal to the amount of physical memory in your system. If you don't use the Hibernate feature and want to reclaim the space used by Windows for the hiberfil.sys file, perform the following steps:

  -Start the Control Panel Power Options applet (go to start, settings, Control Panel, and then click Power Options).
  -Select the Hibernate tab, uncheck "Activate the hibernation", and then click OK. Although you might think otherwise, selecting never under "Hibernate" option on the power management tab does not delete the hiberfil.sys file.
  -Windows remove the "Hibernate" option on the power management tab and delete the hiberfil.sys file.

  You can control the amount of space your system restore can use...

  1. Click Start, right click my computer and then click Properties.
  2. click on the System Restore tab.
  3. highlight one of your readers (or C: If you only) and click on the button "settings".
  4 change the percentage of disk space you want to allow... I suggest moving the slider until you have about 1 GB (1024 MB or close to that...)
  5. click on OK. Then click OK again.

  You can control the amount of space used may or may not temporary Internet files...

  Empty the temporary Internet files and reduce the size, that it stores a size between 64 MB and 128 MB...

  -Open a copy of Microsoft Internet Explorer.
  -Select TOOLS - Internet Options.
  -On the general tab in the section 'Temporary Internet files', follow these steps:
  -Click on 'Delete the Cookies' (click OK)
  -Click on "Settings" and change the "amount of disk space to use: ' something between 64 MB and 128 MB. (There may be many more now.)
  -Click OK.
  -Click on 'Delete files', then select "Delete all offline content" (the box), and then click OK. (If you had a LOT, it can take 2 to 10 minutes or more).
  -Once it's done, click OK, close Internet Explorer, open Internet Explorer.

  You can use an application that scans your system for the log files and temporary files and use it to get rid of those who:

  CCleaner (free!)
  http://www.CCleaner.com/
  (just disk cleanup - do not play with the part of the registry for the moment)

  Other ways to free up space...

  SequoiaView
  http://www.win.Tue.nl/SequoiaView/

  JDiskReport
  http://www.jgoodies.com/freeware/JDiskReport/index.html

  Those who can help you discover visually where all space is used.  Then, you can determine what to do.

  After that - you want to check any physical errors and fix everything for efficient access"

  CHKDSK
  How to scan your disks for errors* will take time and a reboot.

  Defragment
  How to defragment your hard drives* will take time

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need.  This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on the root of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you * NOT * use the aggressive version):
  How to reset the Windows Update components?

  Reset.

  Now that your system is generally free of malicious software (assuming you have an AntiVirus application), you've cleaned the "additional applications" that could be running and picking up your precious memory and the processor, you have authorized out of valuable and makes disk space as there are no problems with the drive itself and your Windows Update components are updates and should work fine - it is only only one other thing you pouvez wish to make:

  Get and install the hardware device last drivers for your system hardware/system manufacturers support and/or download web site.

  If you want, come back and let us know a bit more information on your system - particularly the brand / model of the system, you have - and maybe someone here can guide you to the place s x of law to this end.  This isn't 100% necessary - but I'd be willing to bet that you would gain some performance and features in making this part.

• PC with Windows Vista does not restart after installing updates, "Windows could not start...". "File:\Windows\system\winload.exe status: Oxcoooooof.

  Last night, I installed Windows updates on my HP Pavilion dv6227cl and now Windows will not boot.  I get the message "cannot start Windows.  A recent hardware or software change might be the cause.  File:\Windows\system\winload.exe status: Oxcoooooof Info: the selected entry could not be loaded because the application is missing or damaged.  I DO NOT have the Windows Setup disc.

  Hello

  I suggest you borrow the CD of windows vista to your friends

  Method 1:

  Step 1:

  I suggest you check in safe mode.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  If you be able to start your computer in safe mode, I'd say make clean boot and check.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, make sure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I also suggest you to see link and check.

  Error: Windows could not start. A recent hardware or software change might have caused the problem after installing Windows updates

  http://support.Microsoft.com/kb/2674065

• Windows could not start after activating the boot.

  Hi all

  I have a very serious problem.

  A few lost technology from Microsoft asked that I have to do the following:

  http://support.Microsoft.com/kb/929135.

  Immediately after the restart, I was confronted with the following message:

  Windows could not start.

  Status: 0xc000000e

  Info: A required device is not connected or is not accessible.

  Startup Repair does not work. -Root cause found: the partition table has not a Sys component validates.

  System Restore does not work - the system cannot find the specified file (0 x 80070002)

  Bootrec - rebuildbcd works no item was not found.

  Bootcfg does not work - could not open the TRUNK. INI file.

  Bcdedit does not work - the requested system device cannot be found.

  GParted does not work - cannot load the ntfs module: invalid argument.

  How can it be fixed, please?

  It is an extremely urgent situation which must be resolved immediately, because I use this computer for work and need to return to work on a large commercial project Monday. Forget the original question that MS tech was trying to 'help' with, everything what I need now is to be able to get into Windows, or even just make this record available and accessible on the LAN computer.

  Hi all, thank you for the advice.

  Problem has been resolved after a cold start.

• Can help to solve the issue of "the application could not start properly? < < Error after update CC

  After update Adobe after effects Adobe first Pro CC and CC, via the cloud to create, update, I get the following programs during the boot error message.

  Box "application error".

  "The application could not start correctly (0xc0000142). Click OK to close the application. »

  I had several programs that I've updated (Adobe PhotoShop, Adobe Audition, etc.), at the same time. None of the other programs seems to have problems starting.

  
  

  I uninstalled Adobe after effects Adobe Premiere Pro CC and CC and have the same results, aka, error notice, after reinstalling.
  

  
  

  I did some research and do not seem to have found a definitive solution to the problem.

  
  

  • Can you please help me solve this problem. If you have encountered this problem and it is successfully resolved your entry is particularly useful.
  • Can you suggest ways to avoid this, or similar questions in the future. It makes me feel very reluctant to update my software CC if I'm going to experience the hours/days/weeks of delay due to having to solve problems.

  
  

  Thanks in advance for your help.

  Hi Leslie,.

  After update Adobe after effects Adobe first Pro CC and CC, via the cloud to create, update, I get the following programs during the boot error message.

  Box "application error".

  "The application could not start correctly (0xc0000142). Click OK to close the application. »

  Update for Premiere Pro CC 2015 (9.2) for a fix.

  Thank you
  Kevin

• Try reinstalling firefox on a windows machine 7 and I get «the application could not start correctly (0xc0000142)»

  To solve a different problem, I uninstalled Firefox. After you have solved the other issue I'm tying to re - install Firefox and get an error message that says that "the application could not start correctly (0xc0000142). Click OK to close the application. "The title bar of the window, said"setup - stub.exe - Application error. "My PC is a Dell Studio 19 all-in-one running Windows 7 Home Premium.

  I ended up solving this problem by doing a reinstall on Windows 7 site. It took a little while but fixed this and a few other issues I've had.

• Qosmio G45-AV680 - Windows could not start

  My cousin has this laptop and could not start the system. It displays the message:

  "Unable to start Windows. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert your windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."

  If you don't have this disk, contact your system administrator or computer manufacturer for assistance. Status: 0xc000000f

  "Info: the boot selection failed because a required device is not accessible.

  I tried to go into safe MODE, but it cannot do so. It starts to load the drivers, but it stops at some point and will not continue...
  The problem is that she did not have any DVD with laptop. I guess that the Vista operating system, that comes with it is the special partition on the hard drive, but how can I access it? How can I reinstall the system? I don't mind if I lose data, I used just to make it work...

  If DVD recovery is not assured that means installation of recovery can be started from the HARD drive. I don't know how it works exactly on cell phones in the United States. Try pressing zero button after starting upwards to see if HARD drive recovery option can be started.

  By the way: check the Toshiba U.S. support under http://laptopforums.toshiba.com/tshb/ forum
  Maybe someone there can explain how it works to start the installation of the OS on the HARD drive.

• Computer laptop Compaq could not start

  My laptop model is Compaq Presario CQ40-502AU. I used it for over 2.5 years.

  Recently, the laptop could not start from time to time. The LED flashes to keep, but the laptop does not start.

  Referring to this article:

  http://support.HP.com/us-en/document/c01732674

  I preformed hard reset and manged to get the laptop starts. However, the problem after several days reappered and perform a hard reset is not enough to start the laptop. Sometimes, I need to do the hard reset many times to start the laptop.

  I recorded a video on the State of Flash of the LED.

  https://SkyDrive.live.com/redir.aspx?CID=4aa65a2248b908f1 & RESID = 4AA65A2248B908F1% 21412 & parid = 4AA65A2...

  I don't know if it qualifies as keeps flashing indicating the problem on my adapter?

  Someone please help me on this. Thank you!

  Greetings,

  Disconnect the power adapter and remove the battery from the laptop. Once this is done, press in and hold the power button on the PC for a minute. Only reconnect the AC adapter and try to turn the unit back on. If this problem persists, turn off the device by pressing the power button for 8 seconds. Disconnect the power adapter and the battery. Try to start the PC again.

  If the PC starts, during the Compaq logo, press the ESC key to enter the boot menu. While in the boot menu press the diagnostic mode (should be F10) and run a diagnostics of complete systems. That should tell you which device is a failure. I hope it's nothing serious, maybe a defective battery.

  If your system seems to be stable during the startup and shutdown not randomly on its own, I would try to update the BIOS once started in Windows by downloading on:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-86224-1 & CC = US & DLC = in & LC = on & os = 4062 & Product = 3973096 & sw_lang =

  Don't forget to follow directions exactly as displayed on the HP site.

  Good luck
  Brent

• I've updated my bios with lenovo update... then it could not start

  I have a 3000 n200 0769 b5g... I just updated the bios, then he could not start... What is the solution... is this a format? then I tried to format my pc but I didn't coz he has a 8 GB freespace only when I use my bootable drive... it must have 140 GB... where can I get a good start and I can burn it to a cd...

  Failed to start o? You mean it restarts when it comes to where windows should start up (you get a blue screen), if this is the case, go into the BIOS, and then search for the HARD drive mode (AHCI I think), if the mode is on, turn it off, it should work fine after that.

  If it's a different kind of problem starting, I don't know...

• HP-ENVY-23-d200: error no bootable floppy detected or could not start.

  Hello, I would be very happy to help of the computer. (I'm not all that tech savvy) even if I know a little.

  I have a HP Envy (all in one computer)

  Here is a link http://support.hp.com/us-en/product/HP-ENVY-23-d200-TouchSmart-All-in-One-Desktop-PC-series/5359011/...

  A few days ago, I noticed a few severe freezing. But I could still on my moms on the computer account. It happened because I had turned off the so-called "WMI provider host" I disabled it because he gave me a super high CPU usage. I also read that it was good to disable. But after that, I wasn't able to get into the account admin without her panic. Finally I had refreshed the computer which helped a lot.

  BUT after I had updated to 8.1 (which I have before) I STILL severe freezing. In my attempts to get that to stop, I have completed the tasks that I knew wouldn't freak out my computer. Finally I got fed up with it and tried to factory restore it. BUT during this attempt, my computer freaked out and never finished than restoring plant. He said then that the partition to restore disappeared? After all, I am finally back in the computer said it was fine, and nothing has changed. In order to be smart (for once), I moved everything I had on my external hard drive computer. I also went on the link above looking for updates of pilot thinking that the freezing issue had something to do with it. Had all these installs fact rebooted my computer to receive this error message on ipv4 (ipv6) pxe boot which had not my computer says "error no bootable floppy detected or could not start.»

  I then searched a solution for the PXE on error. Finally got in the bios and that oppresses. Saved and put off the computer. To my surprise the error went away but not only no bootable floppy detected or could not start.

  Then I went to diagonstics and everything seems to work very well. But my question is "is my hard drive of the computer by train to die?" (I have a deep feeling that is close to death) But not so sure, if the hard drive is not the problem. I was going to just to install a new OS which probably will Windows 10 because I don't have money to buy windows 8.1.

  I thank you very much in advance for reading and assistance!

  -Mariam

  Mariam, welcome to the forum.

  Yes, I think that your hard drive is dying. R.I.P.  Here is a guide to help you test using S.M.A.R.T. of the BIOS.  You can enter the BIOS by pressing F10 when the computer starts to boot.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Could not start the time service windows on the local computer 2 error

  Cannot update the system clock of time Internet.

  After double click to display the time in the taskbar, the Date and time properties window appears.

  Then I time tab-click Internet, and then click Update now - this produces the following message...
  "Year error occurred getting the status of the last synchronization." The RPC server is unavailable ".
  Then I clicked on start > Control Panel > Administrative Services > Services > time Windows
  I click Start the service and get the following message...
  "Could not start the time service windows on local computer."
  "error 2: the system cannot find the file specified."
  Help!  What now?

  Hello

  Glad to know that the problem has been resolved. If you have additional questions on the computer, please ask your question about Windows and we will be happy to help you.

• Windows ICS Services stopped & could not start the windows firewall in windows xp professional sp2.

  I am facing a problem regarding the ICS Service & could not start windows in windows Xp service pack 2 firewall, whenever I have install windows Xp Sp2 and join the network, the ics services ceased and the windows firewall. While windows firewall service starts when I restart my computer. But after some time stopped again had services that I'm cold does not access the readers of part, could not access network resources.this problem occurs only on windows xp sp2, when I install windows 7, then all better.i work fetch on different forums, apply the settings but I'm not able to solve the problem on base all the time. Someone tell me the permanent solution of this problem, on a forum, I see this solution,sharedaccess.reg and settings.but I am still unable to find a permanent solution.

  Someone tell me the permanent solution of this problem?
  
  
  
  

  Hello

  Here are a few troubleshooting steps that you can try to solve this problem. See the following links.

  You cannot start the Windows Firewall service in Windows XP SP2

  http://support.Microsoft.com/kb/920074

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

  http://support.Microsoft.com/kb/322756

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  http://support.Microsoft.com/kb/875357

  If you have additional problems, please reply to this post and we will be happy to help you further.